Transflective LCD module with touch panel.
Resolution is selectable between VGA
(480H × 640V) or QVGA (240H × 320V).
Color mode is selectable between 262,144
colors (18-bit RGB) or 8 colors (3-bit RGB).
It incorporates a symmetric wide viewing
angle of 160° × 160°. Full specification listing.
LS037V7DW01 LCD Module
Product Specification
March 2008
LCD Specification
LCD Group
Technical Document
LCP-06008A-1
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright
laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express
written permission is also required before any use of this publication may be made by a third party.
The application circuit examples in this publication are provided to explain the representative applications of
SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or
other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property
right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device
manufacturing processes.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that
occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to
obtain the latest device specification sheets before using any SHARP's device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and
other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP
in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also
subject to change without notice.
Observe the following points when using any device in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices.
The devices in this publication are designed for use in general electronic equipment designs, such as:
Personal computers Office automation Telecommunication equipment
Test and measurement equipment Industrial control
Audio visual and multimedia equipment Consumer electronics
The appropriate design measures should be taken to ensure reliability and safety when SHARP's
devices are used for equipment such as:
Transportation control and safety equipment(i.e., aircraft, trains, automobiles, etc.)
Traffic signals Gas leakage sensor breakers
Alarm equipment Various safety devices etc.
SHARP's devices shall not be used for equipment that requires extremely high level of reliability,
such as:
Military and space applications Nuclear power control equipment
Medical equipment for life support
Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific"
applications other than those recommended by SHARP.
Contact and consult with a SHARP representative if there are any questions about the contents of this
publication.
LCP-06008A-2
(1) Application
This literature applies to LS037V7DW01.
(2) Overview
This module is a color transflective and active matrix LCD module incorporating CG-Silicon TFT
(Continuous Grain-Silicon Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs
(with control Function), an FPC(with DC-DC Converter), a back light, a touch panel and a back sealed casing.
It is composed control circuit. Graphics and texts can be displayed on a 480×3×640 dots panel with
262,144 colors by supplying.
This LCD module has multi resolution and multi colors functions. A resolution mode is selective in
VGA (480H×640V) or QVGA (240H×320V). A Color mode is selective in 262,144 colors (18bit RGB) or
8 colors (3bit RGB).
It is a wide viewing-angle-mode (Vertical viewing angle:(±80°) Horizontal viewing angle: (±80°) ,CR5).
(3) Mechanical specifications
Table 1
Parameter Specifications Units Remarks
Screen size (Diagonal) 9.4 [3.7”] Diagonal cm
Display active area 56.16H×74.88V mm
Touch panel active area 57.4H×76.1V mm
Pixel format 480(H)×640(V)
(1 pixel = R+G+B dots) pixels
Dot pitch 0.039H×0.117V mm
Pixel configuration R,G,B vertical stripe
Display mode Normally Black
Unit outline dimension 65.0(W)×89.2(H)×4.4(D) mm Note3-1
Mass Typ.48
Surface hardness 3H
Note 3-1Excluding protrusion. For detailed measurements and tolerances, please refer to Fig. 1.
(4) Pixel configuration
QVGA modem=240,n=320
VGA mode m=480,n=640
(m,n)
R G B
Display area
LCD/LED/TP
FPC
(m,1) (1,1)
(1,n)
1
51
LCP-06008A-3
(5) Input/Output terminal
5-1) TFT-LCD panel and Backlight driving section
Table2
Pin No. Symbol I/O
Description Remarks
1 LED+ LED power supply(High Voltage) Note5-1
2 NC
3 LED- LED power supply(Low Voltage)
4 NC
5 T4 Touch panel lower electrode(Right side)
6 T3 Touch panel upper electrode(6 o'clock side)
7 T2 Touch panel lower electrode(Left side)
8 T1 Touch panel upper electrode(12 o'clock side)
9 GND Ground
10 RESB I Reset signal Note5-2
11 GND Ground
12 MO I Selection for resolution(VGA/QVGA) Note5-3
13 UD I Selection for vertical scanning direction Note5-4
14 LR I Selection for horizontal scanning direction Note5-5
15 INI I Power on control Note5-2
16 DEN I Data enable signal Note5-6
17 GND Ground
18 VSYNC I Vertical synchronizing signal
19 GND Ground
20 HSYNC I Horizontal synchronizing signal
21 GND Ground
22 CLKIN I System clock signal
23 GND Ground
24 VCC Power supply(3.3V) Note5-2
25 VCC Power supply(3.3V) Note5-2
26 VCC Power supply(3.3V) Note5-2
27 GND Ground
28 B5 I Blue data signal(MSB)
29 B4 I Blue data signal
30 B3 I Blue data signal
31 B2 I Blue data signal
32 B1 I Blue data signal
33 B0 I Blue data signal(LSB)
34 GND Ground
35 G5 I Green data signal(MSB)
36 G4 I Green data signal
LCP-06008A-4
Pin No. Symbol I/O
Description Remarks
37 G3 I Green data signal
38 G2 I Green data signal
39 G1 I Green data signal
40 G0 I Green data signal(LSB)
41 GND Ground
42 R5 I Red data signal(MSB)
43 R4 I Red data signal
44 R3 I Red data signal
45 R2 I Red data signal
46 R1 I Red data signal
47 R0 I Red data signal(LSB)
48 GND Ground
49 SMPSYNC I
Selection for Vertical/ Horizontal synchronizing signal
timing(clock timing) Note5-7
50 SMPDATA I
Selection for Red, Green and Blue data signal timing
(clock timing) Note5-7
51 ID1 Ground
Note5-1When superfluous current flows,please intercept current with a fuse etc.
Note5-2See section(7-1)-(A) ”Cautions when you turn on or off the power supply”.
Note5-3 Selection for resolution mode
MO Resolution
Low VGA(480RGB×640)
High QVGA(240RGB×320)
Note5-4Selection for vertical scanning direction
U/L Scanning direction (Pixel configuration)
High
Conventional scanning ( X , 1 )
( X , Y )
Low
Inverted scanning ( X , 1)
( X , Y)
VGA mode: Y=640, QVGA mode: Y=320
Note5-5Selection for horizontal scanning direction
LBR Scanning direction (Pixel configuration)
High Conventional scanning (1,Y) (X,Y)
Low Inverted scanning (1,Y) (X,Y)
VGA mode: X=480, QVGA mode: X=240
Note5-6
DEN makes it possible to take effective data timing. Horizontal Data Sampling Timing is shown in 7-2)
Timing Characteristics of input signals.
LCP-06008A-5
Note5-7Selection for synchronizing signal and data signal timing(clock timing)
SMPSYNC Selection for Vertical/ Horizontal synchronizing
signal timing(clock timing) SMPDATA
Selection for Red,Green and Blue data signal
timing(clock timing)
High Rise edge of clock(CLKIN) High Rise edge of clock(CLKIN)
Low Fall edge of clock(CLKIN) Low Fall edge of clock(CLKIN)
(6)Absolute Maximum Ratings
Table 3
Parameter Symbol
Condition
Ratings Unit Remark
Power supply (COG driver / Digital) VSHD
Ta=25
-0.3+4.0 V
Input voltage (Digital) VID Ta=25
-0.3VSHD+0.3 V [Terminal]
Touch panel input voltage VIT Ta=25
7.0 V
Note6-1
Operating temperature(Panel surface) opp -1060 Note6-2
Storage temperature stg -2070 Note6-2
LED current IL Ta=25
30 mA
Note6-3
[Terminal] INI,VSYNC,HSYNC,MO,UD,LR,CLK,R0R5,G0G5,B0B5,DEN,RESB
Note6-1Applies to Touch panel input terminal.(xL,xR,yU,yD)
Note6-2Humidity: 95%RH Max.(at Ta 40). Maximum wet-bulb temperature is less than
39 (at Ta > 40). Condensation of dew must be avoided.
Note6-3( Provisional plan) LED current should be as per below figure.
Ambient Temperature vs.
LED Current
0
5
10
15
20
25
30
35
0 10203040506070
Ambient temperature[℃]
LED current[mA]
(7)Electrical characteristics
7-1) Recommended operating conditions
A) TFT-LCD panel driving section
Table4 GND=0V
Parameter Symbol Min. Typ.
Max. Unit Remarks
Supply voltage
for COG driver Digital VSHD +3.0 +3.3
+3.6 V
Input voltage (Low) VILS GND - 0.2VSHD
V Note 7-1
Input voltage (High) VIHS 0.8VSHD
- VSHD V
Note 7-1
Input current (Low) IILS - - 10 μA Note 7-1
Input current (High) IIHS - - 10 μA Note 7-1
LCP-06008A-6
Cautions when you turn on or off the power supply
ON
sequence OFF sequence
Conventional O peration
5Vsync
Conventional Operation
INI(Power on Control)
CLKIN,VSYNC,HSYNC GND
GND GND
GND RESB
VCC
(External power Supply 3.3V)
Min20
μ
sec Width
GND
RGB dat a Si gn al
Conventional Operation GND
GND
GND
2Vsync
2Vsync
(1) After VCC is ON ,please make sure to start HVIF(CLK,HSYNC,VSYNC,RGB data signal) synchronized
signal before INI(Power on control) becomes High.
(2) Please keep HVIF(CLK,HSYNC,VSYNC,RGB data signal) synchronized signal High for more than 5
vertical period after INI becomes Low to shut down VCC.
(3) Stabilize VCC(3.3V) within double vertical periods.
(4) VCC is stabilized to GND within double vertical periods.
(5) When the power supply is on again after Power Supply Off sequence ,please put the RESB signal before
Power Supply On sequence. RESB signal needs LOW level more than 20μsec after VCC(+3.3V) ON.
(6) Please Set RESB signal before INI Signal.
Note 7-1INI,VSYNC,HSYNC,MO,UD,LR,CLK,R0R5,G0G5,B0B5,DEN,RESB terminals are applied.
Each voltage should be kept to satisfy absolute maximum ratings.
If the applied voltage goes beyond absolute maximum ratings, the LCD module may be broken
eternally.
B) Back light driving section
Table 5 Ta=25
Parameter Symbol MIN TYP MAX Units Remarks terminal
LED voltage(VL) VL 27.9 31.5 V Note 7-2
LED current(IL) IL 16 20 mA
Power consumption WL 446.4 630 mW Note 7-3
Note 7-2VL(TYP) at IL(16mA). VL (MAX) at IL (20mA).
Note 7-3Calculated reference value. WL=(VL×IL)
LCP-06008A-7
7-2) Timing Characteristics of input signals
Table 6 AC Characteristics
Parameter Symbol MODE Min. Typ. Max. Unit Note
CLK Period tCLK VGA
QVGA
38
152
39.7
158.8
41.7
167 ns
CLK Low Width tCLKL 15 - - ns
CLK High Width tCLKH 15 - - ns
CLK
Data setup time tDS 10 - - ns
Data hold time tDH 10 - - ns
R0R5,
G0G5,
B0B5
Pulse width of DEN tHHW VGA
QVGA - 480
240 -
Period of HSYNC tHS VGA
QVGA - 648
324 - CLK
Pulse width of HSYNC thsw - 2 - CLK
HSYNC setup time tHSYS 10 - - ns
HSYNC hold time tHSYH 10 - - ns
HSYNC
Horizontal Back Porch tHBP VGA
QVGA
28
14
78
38
166
82 CLK
Horizontal Front Porch tHFP VGA
QVGA
0
0
88
44
138
68 CLK
Period of VSYNC tVS 57 59.94 63 Hz
Period of VSYNC tVS VGA
QVGA
-
-
648
324 - HCYC
Pulse width of VSYNC tvsw - 1 - HCYC
VSYNC setup time tVSYS 10 - - ns
VSYNC hold time tVSYH 10 - - ns
VSYNC
VSYNC-HSYNC
phase difference tVHD 0 HCYC-2 CLK
Note 7-4
Input Signal 1 Rising Time tRISE1 - - 5 ns
Note 7-5
Input Signal 1 Falling Time tFALL1 - - 5 ns
Note 7-5
Input Signal 2 Rising Time tRISE2 - - 5 μs Note 7-6
Input Signal 2 Falling Time tFALL2 - - 5 μs Note 7-6
Reset Pulse Width tRESW 20 - - μs Note 7-7
LCP-06008A-8
Note 7-4HCYC = HSYNC Period(VGA:Typ.648CLK, QVGA:Typ.324CLK)
Note 7-5VSYNC,HSYNC,CLK,R0R5,G0G5,B0B5,DEN terminals are applied.
Input Signal
tRISE1 tFALL1
0.9VDD
0.1VDD 0.1VDD
0.9VDD
Fig 7-1 Input Signal Rising/Falling Timing
Note 7-6INI,RESB terminals are applied.
Input Signal
tRISE2 tFALL2
0.9VDD
0.1VDD 0.1VDD
0.9VDD
Fig 7-2 Input Signal Rising/Falling Timing
Note 7-7Reset Signal Timing chart
RESB
tRESW
Fig 7-3 Reset Timing Signal
7-3)Power consumption
Measurement condition : Vsync=59.94Hz,Hsync=38.84kHz,CLK=25.17MHz,Ta=25 (VGA Mode)
Table 7 (when conventional scan mode)
Parameter Sym Conditions MIN
TYP
MAX Unit Remarks
VSHD Total(Digital+Analog) ISHD VSHD=+3.3V
45 75
mA Note7-8
Note 7-8White Pattern
LCP-06008A-9
VSYNC
RIN[5:0]
GIN[5:0]
BIN[5:0]
HSYNC
4801 3 478477 4
HS
(Typ.648CLK
VSTyp.648H
[Portrait VGA Mode Timing Chart]
RIN[5:0]
GIN[5:0]
BIN[5:0] 640LINE
639LINE 1LINE1LINE 2LINE
[V erti cal T i ming]
[Horizontal Timing]
CLK
HSYNC 2 1 3 4 648 648 3 641 642 643 644 646 647 2 1
DEN
CLKIN
1】
t
HSYS
t
HSYH
t
VHD
t
VSYS
t
VSYH
CLKIN
VSYNC
HSYNC
CLK
t
CLK
RIN[5:0]
GIN[5:0]
BIN[5:0]
t
CLKH
t
CLKL
t
DS
t
DH
Fig 7-3 LCDIF signal timing in Portrait VGA mode
【※1】
【※2】
【※2】
tHSW tHBP tHFP
tvsw
2479
tHHW
tvs(Typ.648)
645
LCP-06008A-10
RIN[5:0]
GIN[5:0]
BIN[5:0]
HSYNC
2401 3 238237 4
HSTyp.324CLK
vs
Typ.324H
[Portrait QVGA Mode Timing Chart]
[V erti cal Timing]
[Horizontal Timing]
CLK
HSYNC 2 1 3 4 324 324 3 321 322 323 2 1
DEN
RIN[5:0]
GIN[5:0]
BIN[5:0] 319LINE 1LINE1LINE 2LINE 320LINE
VSYNC
CLKIN
t
HSYS
t
HSYH
t
VHD
t
VSYS
t
VSYH
CLKIN
VSYNC
HSYNC
CLK
t
CLK
RIN[5: 0]
GIN[5:0]
BIN[5:0]
t
CLKH
t
CLKL
t
DS
t
DH
Fig 7-4 LCDIF signal timing in Portrait QVGA mode
【※1】
【※2】
【※1】 【※2】
tHBP tHFP
tVSW
tHSW
2239
tHHW
tVS(Typ.324)
LCP-06008A-11
() Input Signals, Basic Display Color and Gray Scale of Each Color
Table 8 18bit RGB color display mode
Colors & Data signal
Gray scale
Gray Scale
R0 R1 R2 R3 R4
R5
G0
G1
G2
G3
G4
G5 B0 B1 B2
B3
B4
B5
Black 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
Blue 0 0 0 0 0
0
0
0
0
0
0
0 1 1 1
1
1
1
Green 0 0 0 0 0
0
1
1
1
1
1
1 0 0 0
0
0
0
Cyan 0 0 0 0 0
0
1
1
1
1
1
1 1 1 1
1
1
1
Red 1 1 1 1 1
1
0
0
0
0
0
0 0 0 0
0
0
0
Magenta 1 1 1 1 1
1
0
0
0
0
0
0 1 1 1
1
1
1
Yellow 1 1 1 1 1
1
1
1
1
1
1
1 0 0 0
0
0
0
Basic color
White 1 1 1 1 1
1
1
1
1
1
1
1 1 1 1
1
1
1
Black GS0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
× GS1 1 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
Darker GS2 0 1 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
× È È È È
Ø È È È È
Brighter GS61 1 0 1 1 1
1
0
0
0
0
0
0 0 0 0
0
0
0
Ø GS62 0 1 1 1 1
1
0
0
0
0
0
0 0 0 0
0
0
0
Gray Scale of red
Red GS63 1 1 1 1 1
1
0
0
0
0
0
0 0 0 0
0
0
0
Black GS0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
× GS1 0 0 0 0 0
0
1
0
0
0
0
0 0 0 0
0
0
0
Darker GS2 0 0 0 0 0
0
0
1
0
0
0
0 0 0 0
0
0
0
× È È È È
Ø È È È È
Brighter GS61 0 0 0 0 0
0
1
0
1
1
1
1 0 0 0
0
0
0
Ø GS62 0 0 0 0 0
0
0
1
1
1
1
1 0 0 0
0
0
0
Gray Scale of green
Green GS63 0 0 0 0 0
0
1
1
1
1
1
1 0 0 0
0
0
0
Black GS0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
0
× GS1 0 0 0 0 0
0
0
0
0
0
0
0 1 0 0
0
0
0
Darker GS2 0 0 0 0 0
0
0
0
0
0
0
0 0 1 0
0
0
0
× È È È È
Ø È È È È
Brighter GS61 0 0 0 0 0
0
0
0
0
0
0
0 1 0 1
1
1
1
Ø GS62 0 0 0 0 0
0
0
0
0
0
0
0 0 1 1
1
1
1
Gray Scale of bleu
Bleu GS63 0 0 0 0 0
0
0
0
0
0
0
0 1 1 1
1
1
1
0 : Low level voltage 1 : High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of
total 18 bit data signals, the 262,144-color display can be achieved on the screen.
LCP-06008A-12
(9)Optical characteristics
9-1) Not driving the Back light condition
Table 9 Ta=25
°C
Parameter Symbol Condition Min Typ Max Unit Remarks
θ21,22 30 40 - degree Viewing angle
range θ11, 12 CR1.2 30 40 - degree
[Note 9-1,2]
Contrast ratio CRmax θ =0° - 2 - [Note 9-2,4]
Response Rise τ r - 10 20 ms
time Fall τ d - 10 20 ms [Note 9-3]
White chromaticity x 0.25 0.30 0.35
y
θ =0°
0.30 0.35 0.40 [Note 9-4]
Reflection ratio R θ =0° 2 4 - % [Note 9-5]
* The measuring method of the optical characteristics is shown by the following figure.
* A measurement device is Otsuka luminance meter LCD5200.(With the diffusion reflection unit.)
Center of display
Measuring method (a) for optical characteristics
Photodetector
(with luminosity correction system)
Module
Chemical coated surface
(Optical diffusion treatment)
A diffusion beam A diffusion beam
Normal line
A beam
(through an optical fiber) Touch panel
LCP-06008A-13
9-2) Driving the Back light condition
Table 10 Ta=25°C
Parameter Symbol Condition
Min Typ Max Unit Remarks
θ21,22 40 80 - degree
Viewing angle range
θ11,12 CR5
40 80 - degree [Note 9-1,2,6]
Contrast ratio Crmax 100 200 - [Note 9-2]
Rise τ r - 15 20 ms
Response
time Fall τ d - 20 30 ms [Note 9-3]
x 0.26 0.31 0.36
White chromaticity y
θ = 0°
0.28 0.33 0.38
NTSC ratio S - 35 - %
Brightness Y
θ = 0° 110 165 - cd/m2 I
L=16mA
Uniformity U θ = 0° 60 - - % [Note 9-7]
* The measuring method of the optical characteristics is shown by the following figure.
* A measurement device is TOPCON luminance meter SR-3.(Viewing cone 1)
Measuring method for optical characteristics
Photodetector(including luminosity facter)
Center
Touch
p
anel
LC D mod ule
LCP-06008A-14
Note 9-1Viewing angle range is defined as follows.
Normal Line
θ12
θ22
θ11
θ21
Definition for viewing angle
Note 9-2Definition of contrast ratio:
The contrast ratio is defined as follows:
Photodetecter output with all pixels white(GS63)
Contrast ratio(CR) =
Photodetecter output with all pixels black(GS0)
VCOMAC=5.0Vp-p
Note 9-3Definition of response time:
The response time is defined as the following figure and shall be measured by switching
the input signal for "black" and "white".
0%
10%
90%
100%
Black White
τ d τ r
Time
Photodetecter output
(arbitrary unit)
Black
Note 9-4A measurement device is Minolta CM-2002.
Note 9-5Definition of reflection ratio
Reflection ratio =
Note 9-6A measurement device is ELDIM EZContrast
Light detected level of the reflection by the LCD module
Light detected level of the reflection by the standard white board
LCP-06008A-15
Note 9-7Definition of Uniformity
The brightness should be measured on the
9-point as shown in the right figure.
(10) Display quality
The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection
Standards TFT-LCD.
(11) Touch panel characteristics
Table 11
Parameter Min. Typ. Max. Unit Remark
Input voltage - 5.0 7.0 V
Resistor between terminals(X1-X2) 200 - 650
Resistor between terminals(Y1-Y2) 200 - 640
Line linearity(X direction) - - ±1.5 %
Line linearity(Y direction) - - ±1.5 %
Insuration resistance 20 - - M DC25V 1min
Minimum tension for detecting - - 0.79 N
(12)Mechanical characteristics
12-1) External appearance
See Fig. 1 Outline Dimension
12-2) FPC (for LCD panel) characteristics
Specific connector
LCD-FPC : HIROSE FH23-51S-0.3SHAW(05) (Bottom contact only)
Minimum Brightness
Maximum Brightness
Uniformity = ×100(%)
1/6
1/6
LCP-06008A-16
(13)Design guidance for touchpanel(T/P)
(1) If an consumer will put a palm on housing in normal usage, care should be taken as follows.
(2) Keep the gap, for example 0.3 to 0.7mm,between bezel edge and T/P surface.
The reason is to avoid the bezel edge from contacting T/P surface that may cause a “short”
with bottom layer(See Fig.2)
(3) Insertion a cushion material is recommended.
(4) The cushion material should be limited just on the busbar insulation paste area.
If it is over the transparent insulation paste area, a ”short” may be occurred.
(5) There is one where a resistance film is left in the T/P part of the end of the pole.
Design to keep insulation from the perimeter to prevent from mis-operation and so on.
Housing
Cushion material
PET Film
Insulation metal
Glass
Transparent
Insulation Paste
Key Area
Prohibition Area
Electrode
Layer
0.3
Fig.2
0.7mm
LCP-06008A-17
(14)Handling Precautions
14-1) Insertion and taking out of FPCs
(1) Be sure insert and take out of the FPC into the connector of the set after turning off the power supply
on the set side.
14-2) Handling of FPCs
(1) The FPC for LCD panel shall be bent only slit portion. The bending slit shall be bent uniformly
on the whole slit portion with bending radius larger than 1.0mm ,and only inner side (back side of the
module). Don’t bend it outer side (display surface side).
(2) Don’t give the FPCs too large force, for example, hanging the module with holding FPC. Moreover,
Do not put stress on the components mounted on FPC to avoid failure of the components.
14-3) Installation of the module
(1) On mounting the module, be sure to fix the module on the same plane. Taking care not to warp or twist
the module.
14-4)Precaution when mounting
(1) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off
immediately.
(2) Glass is used for the TFT-LCD panel or touch panel. If it is dropped or bumped against a hard object, it
may be broken. Handle it with sufficient care.
(3) As the CMOS IC is used in this module, pay attention to static electricity when handling it. Take a
measure for grounding on the human body.
14-5)Others
(1) The liquid-crystal is deteriorated by ultraviolet rays. Do not leave it in direct sunlight and
strong ultraviolet rays for many hours.
(2) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and
the panel may be broken. Also, if it is kept at a temperature above the rated storage temperature,
it becomes isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it
at room temperature as much as possible.
(3) If the LCD breaks, don’t put internal liquid crystal into the mouth. When the liquid crystal sticks to the
hands, feet and clothes, wash it out immediately.
(4) Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or
spots.
(5) Observe general precautions for all electronic components.
(6) Static image should not be displayed more than 5 minutes in order to prevent from occurrence of
residual image.
LCP-06008A-18
(15)Reliability Test Conditions for TFT-LCD Module
Table 12
No. Test items Test conditions
1 High temperature storage test Ta=+70 240h
2 Low temperature storage test Ta=20 240h
3 High temperature and
high humidity operating test
Tp=+40 , 95%RH 240h
(But no condensation of dew)
4 High temperature operating test Tp=+60 240h
5 Low temperature operating test Tp=10 240h
6 Electro static discharge test ±200V200pF(0) to Terminals(Contact)
(1 time for each terminals)
7 Shock tset 980 m/s2, 6 ms
±X,±Y,±Z 3 times for each direction
(JIS C0041, A-7 Condition C)
8 Vibration test Frequency range: 10Hz5510Hz
Stroke: 1.5 mm Sweep: 10Hz55Hz
X,Y,Z 2 hours for each direction (total 6 hours)
(JIS C0040,A10 Condition A)
9 Heat shock test Ta=20℃~+70 / 5 cycles
(1h) (1h)
10 Point activation test
(Touch panel)
Hit it 1,000,000 times with a silicon rubber of R8 HS 60.
Hitting force :2.45N(250gf)
Hitting speed : 3 times per second
11 Writing friction resistance test
(Touch panel)
Slide Pen 100,000 times under following
conditions:
Pen : 0.8Rmm Polyacetal stylus
Load : 2.45N(250gf)
Speed : 3 strokes per second
Stroke : 35mm
Testing apparatus : shown in Fig.3
Fig.3
Motor
Touch Panel
Stroke 35mm
Weight
2.45N(250gf)
LCP-06008A-19
NoteTa = Ambient temperature, Tp = Panel temperature
Check items
Test No.19
In the standard condition, there shall be no practical problems that may
affect the display function.
Test No.10No.11
The measurements after the tests are satisfied (11)-Table 11 (Touch panel
characteristics)
(16) Others
16-1)Indication of lot number
The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions).
16-2) Used Regulation of Chemical Substances Breaking Ozone Stratum
Substances with the object of regulating: CFCS, Carbon tetrachloride, Halon
1,1,1-Trichloro ethane (Methyl chloroform)
(a) This LCD module, Constructed part and Parts don’t contain the above substances.
(b) This LCD module, Constructed part and Parts don’t contain the above substances in
processes of manufacture.
16-3) If some problems arise about mentioned items in this document and other items, the user of
the TFT-LCD module and Sharp will cooperate and make efforts to solve the problems with mutual
respect and good will.
(17)Forwarding form (fig4)
a) Piling number of cartons : 8
b) Package quality in one cartons : 100 pcs
c) Carton size : 575 mm × 360 mm × 225 mm
d) Total mass of 1 carton filled with full modules : 8,600 g
Conditions for storage
Environment
(1)Temperature : 040
(2)Humidity : 60%RH or less (at 40)
No dew condensation at low temperature and high humidity.
(3)Atmosphere : Harmful gas, such as acid or alkali which bites electronic
components and/or wires, must not be detected.
(4)Period : about 3 months
(5)Opening of the package : In order to prevent the LCD module from breakdown by
electrostatic charges, please control the room humidity
over 50%RH and open the package taking sufficient
countermeasures against electrostatic charges, such as
earth, etc.
LCP-06008A
NORTH AMERICA
Sharp Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
www.sharpsma.com
TAIWAN
Sharp Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
CHINA
Sharp Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: smc@china.global.sharp.co.jp
EUROPE
Sharp Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com
SINGAPORE
Sharp Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
KOREA
Sharp Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
JAPAN
Sharp Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
HONG KONG
Sharp-Roxy (Hong Kong) Ltd.
3rd Business Division,
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 13B1, Tower C,
Electronics Science & Technology Building
Shen Nan Zhong Road
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for
limitations on special applications. See Limited Warranty for SHARP’s product warranty.
The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,
ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in
any way, for any incidental or consequential economic or property damage.
LCD Group
LCD Specification
Technical Document