AMP INCORPORATED Harrisburg, Pa. 17105 AMP* COAXICON* IS 2028-4 50 OHM, R.F. CONNECTORS RELEASED] 6-8-70 SERIES N PANEL JACKS Se SS The connectors listed below are assem- bled and crimped as described on Page 2. Refer to the table below for tool In- struction Sheet numbers. The following publications contain infarmation on additional series WN connectors. Plugs 2028-4 Jacks 2028-2 Bulkhead Jacks 2028-3 Rt. Angle Plugs 2028-5 Rt. Angie Jacks 2028-6 RECOMMENDED PANEL CUT-OUT -125 MIN, DIA, 4 HOLES 003 FERRULE CENTER CONTACT 18 o-! PANEL JACK BODY NOTE: THIS TYPE FERRULE, CON- TAINING A SEAL, IS USED ON ALL WEATHE RPROGF CONNECTORS. by AMP Incorporatad, Copyright 1969,1970,1972,1974,1975,1976, 1980 Harrisburg, Pa. All Internationa? Rights Reserved. AMP incorporated Praducts covered by U.S. and Foreign Patents and/or Patents Pending. SILVER PLATED P/N TARNISH RES.P/N | CABLE| CRIMPING TOOL TOOL cones RG/u _ STRIP OR 69710 CABLE Desig.t | Standard Weather-| standard | Veatner- Instr. Instr. M39012/ proof proof Part No. Sheet Part No. Sheet . of oo 02-0015 | 61689-3 _ _ _ Fig. 2 | 220015-2 | 2331 _ _ B.8A, 213 02-0016 | 51689-2 | 225089-2| 225885-2} 225666-2] Fig. 2 | 220015-1 | 2331 _ _ 9.9A.9B.214 | 02-0017 | S1689-1 | 225089-1| 225685-1| 2256661 | Fig.1 | 220075-1 | 2331 _ _ 165 _ 51689-7 | 225089-5 _ 225666-6 | Fig.2 | 220015-1 | 2331 _ 225 _ 51689-5 | 225089-4| 225665-7 Fig.1 | 220075-1 | 2331 _ _ 14,114, 144 225666-4 | Fig.2 | 2200151 | 2331 _ 216 _ 225665-5| 225666-5 | Fig.1 | 220015-1 | 2331 _ sri? 30 3 _ 51689-6 | 225089-8 Fig.2 | 220015-3 } 2331 _ _ 115A 1689-4 | 225089-3 | 1-225665-0 _ Fig. 1 | 220015-1 | 2931 _ 58A, 58C _ 7253641 | 225606-4 | 1-225665-2|1-225666-2 | Fig.3 | 220045-2 | 2336 | 220062-1 | 2345 55A, 223 725364-2 | 225606-1 |1-225665-3|1-225666-3 | Fig.3 | 220045-2 | 2336 | 220062-1 | 2345 141, 141A 225364-3 | 225606-4 | 1-225665-4|1-225666-4 | Fig.3 | 220045-2 | 2336 | 220082-1 | 2345 142, 142A, 1428 325364-4 | 225606-2 |1-225665-5| 225701-1 | Fig.3 | 220045-2 | 2336 | 220062-1 | 2345 393 1689-5 | 225089-6 | 226665-7]1-225666-1 | Fig.1 | 220015-1 | 2331 _ ciMes. ie 4) - 225089-7 |t-zesees-6 | Fig.1 | 220015-1 | 2331 _ _ 217 51689-8 _ _ Fig.4 | 220065-1 | 2341 = tGovernment designation applies only to silver plated parts. PAGE 1 OF 2 * TRADEMARK OF AMP INCORPORATED TYPICAL ASSEMBLY PROCEDURE 1. Slide ferrule on cable, then strip cable. DO NOT COMB BRAID. Crimp center contact.(See tool in- structions referenced in table.) 2. insert contact into connector with braid over sup- port sleeve. Pull back lightly on wire to ensure con- tact is retained by an internat locking force established between connector dielectric and center contact. NOTE: The design of parts for smatier cables (RG 55, 58, 141 and 142) allows the center contact to pass beyond the internal locking feature if it is in- serted with too much force. Pull beck on the wire to properly locate and retain the contact in the tocking feature if this condition has occured. 3. Slide ferrule over braid and crimp faerule. (See tool instructions reference in table.) -* SUPPORT SLEEVE OF CONNECTOR CREMPED CONTACT FERRULE SUPPORT SLEEVE SLIDE FERRULE FORWARD OVER BRAID AND SUPPORT SLEEVE WEATHERPROOF CONNECTOR RUBBER SEAL + 1/64 _$__+} 11/16 1/64 vi2t a 3/16 REF. CUT DIELECTRIC SOUARE Fig. 1 + 1/64 es / IE 1/2 41/64 13/16 REF. CUT DIELECTRIC SQUARE Fig. 2 BRAID GVER CONNECTOR 9 +1/64 | 19/8 13/32 +1/64. -| 3/16 REF, CUT DIELECTRIC SQUARE PAGE 20F 2 Fig. 3 - 59/64 + 1/64 J 35/64 +1/64 | 3/8 REF. CUT DIELECTRIC SQUARE Fig. 4 IS 2028-4