T-1 3/4 (5mm) SOLID STATE LAMP Part Number: WP7113ID5V High Efficiency Red Features Description z Low power consumption. The High Efficiency Red source color devices are made with z Popular T-1 3/4 diameter package. Gallium Arsenide Phosphide on Gallium Phosphide Orange z General purpose leads. Light Emitting Diode. z Reliable and rugged. z Long life - solid state reliability. z Available on tape and reel. z 5V internal resistor. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047 Selection Guide Part No. Dice WP7113ID5V Lens Type High Efficiency Red (GaAsP/GaP) Iv (mcd) [2] V= 5V Viewing Angle [1] Min. Typ. 20 40 *12 *25 Red Diffused 21/2 30 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Device Typ. peak Peak Wavelength High Efficiency Red D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 627 nm VF=5V High Efficiency Red 617 nm VF=5V Spectral Line Half-width High Efficiency Red 45 nm VF=5V IF Forward Current High Efficiency Red 13 17.5 mA VF=5V IR Reverse Current High Efficiency Red 10 uA VR = 5V Note: 1.Wavelength: +/-1nm. 2.Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25C Parameter High Efficiency Red Units Power dissipation 85 mW Forward Voltage 6 V Reverse Voltage 5 V Operating Temperature -40C To +70C Storage Temperature -40C To +85C Lead Solder Temperature [1] 260C For 3 Seconds Lead Solder Temperature [2] 260C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047 High Efficiency Red WP7113ID5V SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047 PACKING & LABEL SPECIFICATIONS WP7113ID5V SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047 SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047 All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2406 REV NO: V.4A DATE: MAR/30/2013 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1101005047