Product Specification 25.78Gb/s RoHS Compliant Short Wavelength SFP+ Transceiver FTLF8536P4BCL PRODUCT FEATURES Up to 25.78 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS compliant 100m over M5F MMF (50/125 um OM4) 70m over M5E MMF (50/125um OM3) 20m on MMF (50/125m OM2) Metal enclosure, for lower EMI 1.2W maximum power consumption Single 3.3V power supply Operating temperature range: APPLICATIONS 25.78 Gb/s single lane 100GE SR4 0C to 70C Finisar's FTLF8536P4BCL SFP+ transceivers are designed for use in 25Gb/s data rate over multimode fiber. They are compliant to IEEE802.3by, SFF-8472 Rev 12.2b and SFF-8402g, and compatible with SFF-8432a and applicable portions of SFF-8431 Rev. 4.1c. The transceiver is RoHS compliant and per Directive 2011/65/EUd . See Finisar Application Note AN-2038 for more details. PRODUCT SELECTION FTLF8536P4BCL Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 1 FTLF8536P4BCL Product Specification I. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Descriptions Symbol VEET TFAULT TDIS SDA SCA MOD_ABS RS0 LOS RS1 VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. 2-wire Serial Interface Data Line (MOD-DEF2) 2-wire Serial Interface Clock (MOD-DEF1) Module Absent, connected to VEET or VEER NC Loss of Signal indication. Logic 0 indicates normal operation. NC Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 4 4 4 5 6 5 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k - 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 4. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. Rate select can also be set through the 2-wire bus in accordance with SFF-8472 v. 12.1c. Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h. Note: writing a "1" selects maximum bandwidth operation. Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. 6. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 2 FTLF8536P4BCL Product Specification Towards Bezel 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 Towards ASIC Diagram of Host Board Connector Block Pin Numbers and Names Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 3 FTLF8536P4BCL Product Specification II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity (Non-condensing) Symbol Vcc TS TC RH Min -0.5 -40 0 0 Typ Max 4.0 85 70 85 Unit V C C % Ref. Max 3.46 290 Unit V mA mV V V mV V V mVpp 1 Notes: 1. Non Condensing III. Electrical Characteristics (TA, VCC = 3.15 to 3.46 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single-ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Single ended data output swing LOS Fault LOS Normal Power Supply Rejection Symbol Vcc Icc Min 3.15 Typ Rin Vin,pp VD VEN 100 90 2 Vee 800 Vcc Vee+0.8 Vout,pp VLOS fault VLOS norm PSR 185 2 Vee 100 425 VccHOST Vee+0.8 Ref. 1 2 3 4 5 5 6 Notes: 1. With established link. The total power dissipation could exceed 1W when the module is trying to establish link at operating case temperature below 25oC 2. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. LOS is an open collector output. Should be pulled up with 4.7k - 10kohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 4 FTLF8536P4BCL Product Specification IV. Optical Characteristics (TA, VCC = 3. 15 to 3.46 Volts) Parameter Symbol Min POUT Optical Modulation Amplitude OMA -6.4 Transmitter and Dispersion Eye Closure @25.7Gb/s TDEC Typ Max Unit Ref. -8.4 2.4 860 0.60 dBm nm nm dBm dB dB/Hz 1 840 Transmitter Avergare Output Power: 50 or 62.5 MMF Optical Wavelength Spectral Width (RMS) Relative Intensity Noise Extinction Ratio @25.78Gb/s RIN ER 3 4.3 -128 2 Receiver Stressed Receiver OMA Sensitivity @25.78Gb/s Average Receiver Power @25.78Gb/s Optical Center Wavelength Optical Return Loss LOS De-Assert LOS Assert LOS Hysteresis RxSENS dBm -5.2 RxMAX -10.3 3 C 840 860 12 LOSD LOSA -13 -30 0.5 dBm nm dB dBm dBm dB Notes: 1. Class 1 Laser Safety limit per FDA/CDRH, and EN (IEC) 60825 laser safety standards. 2. Informative Only Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 5 2 FTLF8536P4BCL Product Specification IV. General Specifications Parameter Data Rate Bit Error Rate Fiber Length on 50/125m highbandwidth (OM3/M5E) MMF Fiber Length on 50/125m highbandwidth (OM4/M5F) MMF Symbol Min BR BER Typ Max 25.78 Units Ref. Gb/sec 5E(-5) L 70 m 1 L 100 m 6 Max 70 85 Units C C Notes: 1. At 25.78Gb/s Ethernet data rate (IEEE 802.3by) VI. Environmental Specifications Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. . Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 6 FTLF8536P4BCL Product Specification VIII. Digital Diagnostic Functions Finisar FTLF8536P4BCL SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFP MSAf. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN-2030: "Digital Diagnostics Monitoring Interface for SFP Optical Transceivers". The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentationc,f and Finisar Application Note AN2030. TX Equalization Control Tx input equalization control can be accessed through 2-wire serial interface at byte address 114 (A2h). Tx input equalization control for 25GE is located at the upper 4 bits of byte 114 (A2h) while the lower 4 bits are reserved for rate low in the case of dual rate application. RX Emphasis Control Rx output emphasis control can be accessed through 2-wire serial interface at byte address 115 (A2h). Rx output emphasis control for 25GE is located at the upper 4 bits of byte 115 (A2h) while the lower 4 bits are reserved for rate low in the case of dual rate application. Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 7 FTLF8536P4BCL Product Specification IX. Digital Diagnostic Specifications FTLF8536P4BCL transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Transceiver temperature Transceiver supply voltage Transmitter bias current Transmitter output power Receiver average optical input power Symbol Units DDDTemp C DDDVoltage V DDDBias mA DDDTx-Power dBm DDDRx-Power dBm Min 0 3.14 0 -9 -11 Max +70 3.45 50 +2.4 +2.4 Accuracy Ref. 5C 3% 10% 1 3dB 3dB Notes: 1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser. Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 8 FTLF8536P4BCL Product Specification X. Mechanical Specifications Finisar's FTLF8536P4BCL SFP+ transceivers are compatible with the SFF-8432b specification for improved pluggable form factor. FTLF8536P4BCL Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 9 FTLF8536P4BCL Product Specification XI. PCB Layout and Bezel Recommendations Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 10 FTLF8536P4BCL Product Specification Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 11 FTLF8536P4BCL Product Specification XII. References a. "Improved Pluggable Form Factor", SFF Document Number SFF-8432, Revision 5.0, July 16, 2007. b. "Digital Monitoring Interface for Optical Transceivers", SFF Document Number SFF-8472, Revision 12.2. c. "Enhanced Small Form Factor Pluggable Module `SFP+ `", SFF Document Number SFF-8431, Revision 4.1, July 6, 2009; Addendum Jun 21, 2013. d. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". 08-June 2011, which supercedes the previous ROHS Directive 2002/95/EC. e. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000 which is available as SFF Document Number INF-8074, Revision 1.0 May 12, 2001 f. "0.8mm Card Edge Connector for 16Gb/s Applications", SFF Document Number SFF-8081, Revision 0.2, December 21, 2009. g. SFF-8402, Revision 0.2 XIII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - January 2017 Rev C2 Finisar Confidential Page 12