PD 1.033A DPA Series ChipSwitch(R) DIP Relay Microelectronic Power IC Relay 1.0 Amp Load Current, 20 - 280 VACRMS General Description DPA Series Features The DPA Series ChipSwitch uses exclusive International Rectifier S3X power integrated circuit technology to form a fully functioning solid-state relay. The S3X technology combines MOS and bipolar processes, derived from IR's HEXFET(R) power MOSFET designs, to eliminate the need for both discrete components and hybrid circuits. The basic DPA Series ChipSwitch consists of two identical power integrated circuits connected in inverse parallel (analogous to back-to-back SCRs) for AC control plus an isolated GaAIAs light emitting diode (LED) for actuation. Voltage controlled models with an internal resistor to limit the control current are also available. Extreme reliability is achieved by the reduction of component count from approximately 20 discrete components in a conventional SSR to 3 basic components in the ChipSwitch. The DPA Series ChipSwitch is a single-pole, normally-open SSR capable of switching up to 1.0 ARMS load currents with precise zero-voltage turnon and zero-current turn-off, thus reducing EMI emissions. These devices are ideally suited for interfacing microprocessors to AC loads, such as small motors, lamps, solenoids, valves and high power motor starters. The economy of the DPA Series ChipSwitch allows the in-house manufacturer to replace assemblies of triacs, triac drivers and associated components with a highly reliable, miniature, standard SSR. S3X power IC chips n 25 Amp surge n 4,000 VRMS I/O isolation n 10 A off-state leakage current n Zero-voltage turn-on n Operates without snubber n 600 V/s off-state dv/dt n Solid-State reliability n UL recognized and CSA certified n Part Identification Part Number DPA4111 DPA4119 DPA6111 DPA6119 Transient Overvoltage (V PEAK) 400 400 600 600 Operating Voltage (VRMS) 20-140 20-140 20-280 20-280 (ChipSwitch and HEXFET are trademarks of International Rectifier) DC Input Sensitivity (Turn-On) 10mA 3.5V 10mA 3.5V Series DPA ChipSwitch(R) DIP Relay Electrical Specifications (-30C TA +85C unless otherwise specified) INPUT CHARACTERISTICS Limits Units Maximum Turn-On Current: DPA4111, DPA6111 Minimum Turn-Off Current: DPA4111, DPA6111 Control Current Range (Caution: current limit input LED, see figure 3) DPA4111, DPA6111 (see figure 4 for DPA4119, DPA6119) Maximum Turn-On Voltage: DPA4119, DPA6119 Minimum Turn-Off Voltage: DPA4119, DPA6119 Control Voltage Range: DPA4119, DPA6119 Maximum Reverse Voltage (All Models) 10.0 0.5 10 to 25 mA mA mA 3.5 0.8 3.5 to 7 7.0 V V V V OUTPUT CHARACTERISTICS Operating Voltage Range (47 - 63 Hz) Transient Overvoltage (non-repetitive) Maximum Load Current @ TA=+40C (see figure 1) (see Note 3) Minimum Load Current Minimum Off-State dv/dt (see Note 1) Power Factor Range Maximum On-State Voltage Drop @ 1.0 ARMS Maximum Off-State Leakage Current (see Note 2) Maximum Turn-On Time (60 Hz) Maximum Turn-Off Time (60 Hz) Maximum Surge Current, Single-Cycle, Non-Repetitive 20 ms (see figure 2) Maximum Overcurrent, Non-Repetitive 1 second Maximum I2T for Fusing (0.01 sec) Maximum Zero Voltage Turn-on GENERAL CHARACTERISTICS Minimum Dielectric Strength, Input-Output Minimum Insulation Resistance, Input-Output, @TA=+25C, 50%RH, 500VDC Tracking Resistance (VDE Test) Maximum Capacitance, Input-Output Maximum Pin Soldering Temperature (10 seconds maximum) Ambient Temperature Range: Operating Storage Limits DPA4111 DPA4119 DPA6111 DPA6119 20-140 400 20-280 600 Units 1.0 0.5 600 0.2 to 1.0 1.5 10 8.3 8.3 25 7.5 4.5 12 VRMS VPEAK ARMS mARMS V/S -- VPEAK ARMS ms ms APEAK APEAK A2s VPEAK Limits Units 4000 1012 KB 100/A 2.0 +260 -30 to +85 -40 to +100 VRMS -- pF C Notes: 1. Off-state dv/dt test method per EIA/NARM standard RS-443 with VP equal to the instantaneous peak of the maximum operating voltage. 2. LED input currrent of zero mA(DPA4111, DPA6111) or input voltage of zero Volts (DPA4119, DPA6119). 3. The UL508 motor control rating per Sec. 52 overload test conditions is 0.4A max., and general purpose and incandescent load control rating is 1.0A. Series DPA ChipSwitch(R) DIP Relay 40 Maximum Surge Current (A peak) 1.4 Load Current (Arms) 1.2 1.0 0.8 0.6 0.4 0.2 Note: Curve represents a non-repetitive uniform amplitude pulse of given time and peak current. Tj 40 deg.C before surge. Control of conduction may be lost during surge. 35 30 25 20 15 10 5 0 0.0 20 30 40 50 60 70 80 90 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2.0 Ambient Temperature (deg. C) Surge Duration (seconds) Figure 1. Derating Curve, Free Standing Figure 2. Maximum Allowable Surge 5.0 10 20 CAUTION: p rovide current lim iting so that 25 m A max imum stead ysta te control current rating is not exceeded 16 30 DPA4111 DPA6111 0 0 0.5 Maximum Input Current (mA) Ma x. de vic e Min . de vice 4 an d -4 0 de g. C limit 8 TYP I CAL and +85 de g. C l imit Input Current (mA) 12 1.0 1.5 2.0 DPA4119 DPA6119 20 10 0 1 2 3 4 5 6 7 8 LED Forward Voltage Drop (Volts DC) Input Voltage (Volts DC) Figure 3. Input Characteristics (Current Controlled) Figure 4. Input Characteristics (Voltage Controlled) Series DPA ChipSwitch(R) DIP Relay Case Outline Dimensions in millimeters (inches) Wiring Diagram +DC 16 Input (Control) -DC 1 10 AC Output (Load) 8 AC WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331 EUROPEAN HEADQUARTERS: Hurst Green, Oxted, Surrey RH8 9BB, UK Tel: ++ 44 1883 713215 IR CANADA: 7321 Victoria Park Ave., Suite 201, Markham, Ontario L3R 2Z8, Tel: (905) 475 1897 IR GERMANY: Saalburgstrasse 157, 61350 Bad Homburg Tel: ++ 49 6172 96590 IR ITALY: Via Liguria 49, 10071 Borgaro, Torino Tel: ++ 39 11 451 0111 IR FAR EAST: K&H Bldg., 2F, 3-30-4 Nishi-Ikeburo 3-Chome, Toshima-Ku, Tokyo, Japan 171 Tel: ++ 81 3 3983 0641 IR SOUTHEAST ASIA: 315 Outram Road, #10-02 Tan Boon Liat Building, Singapore 0316 Tel: ++ 65 221 8371 http://www/irf.com/ Data and specifications subject to change without notice. 9/96