萬達光電科技股份有限公司
PRODUCT SPECIFICATIONS
產 品 規 範 書
Customer (客戶)：
Model (型式)：T170S-5RB004N-0A18R0-200FH
Mode (種類)：Five-wire Analog Touch Panel
Date (日期)：May 06, 2008
Version (版本)：6.3
Customer Approval
客 戶 簽 認
HIGGSTEC INCORPORATED
8 F., No. 609, Wan Shou Rd., Sec. 1,
Kweishan, Taoyuan Hsien 33350,
Taiwan.
TEL：886-2-8209-9696
FAX：886-2-8200-3030
E-mail：info@higgstec.com.tw
Approve
確認
Review
審訂
Preparation
製表
Henry Andy Young
TABLE OF CONTENTS
目 錄
00. Specification Revision Record [規格變更記錄].……………………………………….. 01
00. Dimension Drawing [尺寸圖].…………………………………………………. ……….. 02
01. Scope [範圍].……………………………………………………………………………….. 03
02. Features [特性].…………………………………………………………………………….. 03
03. General Specification [一般規格].………………………………………………………... 03
04. Environmental Characteristics [環境特性].……………………………………………. 03
05. Optical Characteristics [光學特性].……………………………………………………… 04
06. Electrical Characteristics [電子特性].…………………………………………………… 04
07. Mechanical Characteristics [機械特性].………………………………………………... 05
08. Reliability [可靠度].…………………………………………………………………………. 05
09. Durability [耐久性].…………………………………………………………………. ……… 05
10. Inspection Methods [檢查方法].………………………………………………….………. 06
11. Appearance Inspection [外觀檢查].……………………………………………………… 07
12. Attention for Mounting Condition [裝機注意事項].……………………………..………. 08
13. Warranty [保固].……………………………………………………………………………. 09
14. Appendices [附註].………………………………………………………………………… 09
Appearance Specification [外觀檢查規格]………………………………………………. 11
15. Caution [注意事項].…………………………………………………………………………... 10
Date: May 06, 2008 Version: 6.3
SPECIFICATION REVISION RECORD
規格變更記錄
Customer [客戶名稱]： Date [發行日期]：May 06, 2008
Customer NO. [客戶編號]： Model [型式]：T170S-5RB004N-0A18R0-200FH
NO.
[項次]
Version.
[版本]
Date
[變更發行日期]
Summary of Changes
[變更內容摘要]
Page
[變更頁碼]
＜Remarks＞[備註欄]
Date: May 06, 2008 Version: 6.3 Page: 01/11
01. Scope
[範圍] The specification is for Five-Wire Analog Resistive touch panel.
[此規格適用於五線-類比電阻式觸控屏幕]
02. Features
[特性] Item [項目] Specifications [規格]
(1) Type
[型式]
Five-Wire Analog Resistive
[五線-類比電阻式]
(2) Input Mode
[操作模式]
Stylus or Finger
[筆觸或手觸]
(3) Cable
[連結線] FFC
03. General
Specification
[一般規格]
Item [項目] Specifications [規格]
(1) Frame Size
[外框尺寸] 356.00±0.30 X 286.50±0.30 mm
(2) View Area
[可視區] 343.00±0.20 X 275.50±0.20 mm
(3) Active Area
[動作區] 337.00±0.20 X 269.50±0.20 mm
(4)
Tota l
Thickness
[總厚度]
2.20±0.20 mm
(5) Tail Length
[出線長度] 205.00±6.00 mm
04. Environmental
Characteristics
[環境特性] Item [項目]
Specifications [規格]
Temperature [溫度] Humidity [濕度]
(Non Condensing)
[未凝結]
(1) Operation
[操作] -10°C ~ +70°C 20%RH ~ 80%RH
(2) Storage
[儲存] -40°C ~ +80°C 10%RH ~ 85%RH
Note: All terms under 1 atmosphere.
[註:於正常的 1大氣壓下]
Date: May 06, 2008 Version: 6.3 Page: 03/11
05. Optical
Characteristics
[光學特性]
Item [項目] Specifications [規格]
(1) Transparency
[透光度]
80% ± 3%
(Measured by BYK-Gardner )
(2) Haze
[霧化度] 8% ± 3%
06. Electrical
Characteristics
[電子特性]
Item [項目] Specifications [規格]
(1)
Loop
Resistance
[迴路阻抗]
X:20~500Ω, Y:20~500Ω (See Figure 6-1)
(2) Linearity
[線性] X≦1.0%, Y≦1.0% (See Figure 10-2)
(3) Chattering
[作動時間] ≦15ms
(4) Insulation
[絕緣阻抗] ≧20MΩ/25V(DC)
(5) Endurance
[耐電壓] No acting damage at DC50V/60sec.
Figure 6-1
Loop Resistance X = short RT and RL , short LT and
LL , measure the resistance between RT and LT
Loop Resistance Y = short RT and LT , short RL and
LL ,measure the resistance between RT and RL
Date: May 06, 2008 Version: 6.3 Page: 04/11
07. Mechanical
Characteristics
[機械特性]
Item [項目] Specification [規格] Condition [條件]
Operating Force
[作動力]
Stylus=R0.8
[筆式=R0.8] ≦50g
Impact
[撞擊]
13.0ψDIA. Steel Ball/9g
Height=30cm
[13ψ/9g 鋼球 高度=30cm]
1 time, no damage
[Impact at center area]
[中央區域撞擊 1次,不能破損]
Static Load
[靜態承重]
500g within 10cm ² area for
30sec
[500g 置於 10cm²內，30 秒]
Satisfy(1) of Item 7 and
(1), (2),(4) of Item 6
[符合7項目(1)及6項目(1),(2),(4)]
Hardness
[硬度]
3H pencil, pressure 1N/45°
[鉛筆 3H,壓力 1N/45°(JIS K5400)] ≧3H
Peeling
[剝離]
800g by vertical 90°
[800g , 垂直 90°]
Satisfy (1) of Item 6
[符合 6項目(1)]
Bending
[繞折]
135°10 times left & right
[135°角,左右來回 10 次]
Satisfy (1) of Item 6
[符合 6項目(1)]
08. Reliability
[可靠度] Item [項目] Specification [規格] Condition [條件]
High
Temperature
/Humidity
[高溫高濕]
70°C /90%RH, 500 hrs, allow
panel stays in normal
environment for 4 hrs
[70°C /90%RH，500 小時，回常溫 4小時後
始可測試]
Reliability test may cause the
film puffed yet the electric
characteristic stays intact. (1),
(2) of Item 5; (1), (4) of Item 6;
(2) of item 6 satisfies
X≦2.0%, Y≦2.0%;Actuation
force must not exceed 150g
after reliability test.
經由可靠度測試後，外觀不在其規
範內，但功能性仍符合以下條件
[符合 5項目(1)、(2)及6項目(1)、
(4) ; 6 項目(2)符合 X≦2.0%, Y≦
2.0%; 測試後作動力不能超過
150g]
High temperature
[高溫]
70°C /500 hrs allow panel stays
in normal environment for 4 hrs
[70°C /500 小時，回常溫 4小時後始可測試]
Low temperature
[低溫]
-40°C /500 hrs allow panel
stays in normal environment for
4 hrs
[-40°C /500 小時，回常溫 4小時後始可測試]
Thermal Cycle
[冷熱循環]
-40°C ~70℃
[60 min./cycle] *100 cycles
allow panel stays in normal
environment for 4 hrs
[-40°C ~70°C，每循環 60 分鐘，共 100 次循
環，回常溫 4小時後始可測試]
09. Durability
[耐久性] Item [項目] Specification [規格] Condition [條件]
Knock Test
[觸擊測試]
35,000,000 times
[3500 萬次]
Satisfy (1), (2) of Item 5; (1),
(4) of Item 6; (2) of item 6
satisfies X≦2.0%, Y≦2.0%;
Actuation force must not
exceed 150g after durability
test.
[符合 5項目(1)、(2)及6項目(1)、
(4) ; 6 項目(2)符合 X≦2.0%, Y≦
2.0%; 測試後作動力不能超過
150g]
Date: May 06, 2008 Version: 6.3 Page: 05/11
10. Inspection
Methods：
[檢查方法]
(1) Linearity Condition [線性測試條件]
Step 1: short RT and RL(or short RL and LL).
Step 2: apply voltage DC 5V.
Step 3: short LT and LL (or short RT and LT).
Step 4: apply grounding.
Step 5: draw points along LX and LY at 5.0mm intervals within
pattern area and detect the voltage at SG.
Step 6: measure the voltage differences between RT and LT
(or RT and RL) (Fig 10-1) (Fig 10-2)
[將RT , RL 短路(或 RL , LL 短路)並接上 5V 的直流電, 另外將 LT , LL 短路(或 RT , LT 短路)並接上接地
線圈 0V , 以5.0mm 的間隔, 利用手寫筆(stylus)劃直線(如圖 2中LX 和LY),並量測 SG 的電壓, 量測並計
算 RT 與 LT 間的電位差(或 RT 與 RL 間的電位差) ] (Fig 10-1) (Fig 10-2)
Figure 10-1
Figure 10-2
※ Linearity: [│Vxm-Vxi│] / (Va-Vb) X 100%
(2) Specification [規範]
Linearity must meet the electrical characteristic specified in Item 6
[線性必須符合 6項目的電性規範]
Date: May 06, 2008 Version: 6.3 Page: 06/11
11.
A
ppearance
Inspection
[外觀檢查]
(1) A 17W fluorescent luminant lamp is used for appearance
inspection. Detail settings are shown in (Fig 11-1) and (Fig 11-2).
[(1) 檢測始用之燈光為一盞 17W 白熾燈光，詳細的擺設方式，請參考圖(Fig11-1), (Fig11-2) ]
(2) Minor impurities outside viewing area are acceptable unless
their existance affect electrical functions.
[(2) 只要不影響電器功能性，可視區外之外觀暇疵是可以被允許的]
.
Figure 11-1 Figure 11-2
(3) Glass Flaw [玻璃瑕疵]
Item [項目] Picture [圖示] Specification [規
格]
Corner Flaw
[角瑕疵]
X≦3.0mm
Y≦3.0mm
Z≦T
Edge Flaw
[邊緣瑕疵]
X≦3.0mm
Y≦3.0mm
Z≦T
Progressive Flaw
[裂縫瑕疵]
Not allowed
[不允許]
Note: T=Glass thickness
(4) Please refer to AppendixⅠ：Appearance Specification.
[(4)外觀規格請詳見(附註 1)]
Date: May 06, 2008 Version: 6.3 Page: 07/11
12.
A
ttention of
Mounting
Condition
[裝機注意事項]
(1) The gasket support of touch panel must allocate outside of
Viewable Area. Reserve enough clearance between panel
surface and enclosure for normal panel operation.
To avoid pressing error, please retain enough space between
surface panel and Bezel.
[請將固定觸控屏用的支撐體(support)設計於可視區(Viewable area)之外。為避免不小心碰到觸控
屏而產生動作，請預留空間於面板與機體外殼之間]
(2) Bezel opening must not touch Viewable Area, Bezel opening
must be designed between Viewable Area and Active Area.
[外殼內緣(Bezel opening)應設計於可視區及動作區之間，並且不得碰到可視區]
(3) We recommend elastic material support.
[建議使用彈性物質製成的支撐體]
(4) Due to the conductive characteristic of the panel backside,
prevent metal contact after mounting.
[觸控屏面板背面具導電性質，
