B32672L8562J189 - EPCOS (TDK)

Film Capacitors

Metallized Polypropylene Film Capacitors (MKP)

Series/Type: B32671L, B32672L

Date: June 2018

information contained therein without EPCOS' prior express consent is prohibited.

EPCOS AG is a TDK Group Company.

Typical applications

Electronic ballasts (resonant circuits)

SMPS

High-frequency AC loads

Pulse circuits

Climatic

Max. operating temperature: 125 °C

Climatic category (IEC 60068-1:2013):

55/110/56

Construction

Dielectric: metallized polypropylene (PP)

Wound capacitor technology

Plastic case (UL 94 V-0)

Epoxy resin sealing

Features

Very high AC voltages for all frequency

ranges

Very small dimensions

High peak voltage for short time periods

High peak current

High pulse withstand capability

RoHS-compatible

Halogen-free capacitors available on request

AEC-Q200D compliant

Terminals

Parallel wire leads, lead-free tinned

Special lead lengths available on request

Marking

Manufacturer's logo

lot number, series number

Rated capacitance (coded)

Capacitance tolerance (code letter)

Rated voltage

Date of manufacture (coded)

Delivery mode

Bulk (untaped)

Taped (Ammo pack or reel)

For notes on taping, refer to chapter "Taping and packing“.

Dimensional drawing

Dimensions in mm

Lead spacing

±0.4

Lead diameter

d1±0.05

Type

10 0.6 B32671L

15 0.8 B32672L

Metallized polypropylene film capacitors (MKP) B32671L, B32672L

High V AC, high temperature (wound)

Page2of39Please read Cautions and warnings and

Important notes at the end of this document.

Overview of available types

Lead spacing 10 mm 15 mm

Type B32671L B32672L

Page 4 6

VRMS (V AC) 200 250 250 500 600 700 160 200 250 250 500 600 700 900

VR(V DC) 400 630 1000 1000 1600 2000 250 450 630 1000 1300 1600 2000 2000

CR(nF)

1.0

1.2

1.5

2.2

2.7

3.3

3.9

4.7

5.6

6.2

6.8

8.2

100

150

220

330

390

470

680

1000

B32671L, B32672L

High V AC, high temperature (wound)

Page3of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 10 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

200 400 22 4.0 ×9.0 ×13.0 B32671L4223+*** 4000 6800 4000

33 4.0 ×9.0 ×13.0 B32671L4333+*** 4000 6800 4000

47 5.0 ×11.0 ×13.0 B32671L4473+*** 3320 5200 4000

68 5.0 ×11.0 ×13.0 B32671L4683+*** 3320 5200 4000

100 6.0 ×12.0 ×13.0 B32671L4104+*** 2720 4400 4000

250 630 15 4.0 ×9.0 ×13.0 B32671L6153+*** 4000 6800 4000

22 5.0 ×11.0 ×13.0 B32671L6223+*** 3320 5200 4000

33 5.0 ×11.0 ×13.0 B32671L6333+*** 3320 5200 4000

47 6.0 ×12.0 ×13.0 B32671L6473+*** 2720 4400 4000

56 6.0 ×12.0 ×13.0 B32671L6563+*** 2720 4400 4000

250 1000 4.7 4.0 ×9.0 ×13.0 B32671L9472+*** 4000 6800 4000

6.8 4.0 ×9.0 ×13.0 B32671L9682+*** 4000 6800 4000

10 5.0 ×11.0 ×13.0 B32671L9103+*** 3320 5200 4000

15 5.0 ×11.0 ×13.0 B32671L9153+*** 3320 5200 4000

22 6.0 ×12.0 ×13.0 B32671L9223+*** 2720 4400 4000

500 1000 3.3 4.0 ×9.0 ×13.0 B32671L0332+*** 4000 6800 4000

3.9 4.0 ×9.0 ×13.0 B32671L0392+*** 4000 6800 4000

4.7 4.0 ×9.0 ×13.0 B32671L0472+*** 4000 6800 4000

5.6 5.0 ×11.0 ×13.0 B32671L0562+*** 3320 5200 4000

6.2 5.0 ×11.0 ×13.0 B32671L0622+*** 3320 5200 4000

6.8 5.0 ×11.0 ×13.0 B32671L0682+*** 3320 5200 4000

8.2 6.0 ×12.0 ×13.0 B32671L0822+*** 2720 4400 4000

10 6.0 ×12.0 ×13.0 B32671L0103+*** 2720 4400 4000

12 6.0 ×12.0 ×13.0 B32671L0123+*** 2720 4400 4000

B32671L

High V AC, high temperature (wound)

Page4of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 10 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

600 1600 1.2 4.0 ×9.0 ×13.0 B32671L1122+*** 4000 6800 4000

1.5 4.0 ×9.0 ×13.0 B32671L1152+*** 4000 6800 4000

2.2 5.0 ×11.0 ×13.0 B32671L1222+*** 3320 5200 4000

2.7 5.0 ×11.0 ×13.0 B32671L1272+*** 3320 5200 4000

3.3 6.0 ×12.0 ×13.0 B32671L1332+*** 2720 4400 4000

3.9 6.0 ×12.0 ×13.0 B32671L1392+*** 2720 4400 4000

4.7 6.0 ×12.0 ×13.0 B32671L1472+*** 2720 4400 4000

700 2000 1.0 4.0 ×9.0 ×13.0 B32671L8102+*** 4000 6800 4000

1.2 4.0 ×9.0 ×13.0 B32671L8122+*** 4000 6800 4000

1.5 4.0 ×9.0 ×13.0 B32671L8152+*** 4000 6800 4000

2.2 5.0 ×11.0 ×13.0 B32671L8222+*** 3320 5200 4000

2.7 5.0 ×11.0 ×13.0 B32671L8272+*** 3320 5200 4000

3.3 5.0 ×11.0 ×13.0 B32671L8332+*** 3320 5200 4000

3.9 6.0 ×12.0 ×13.0 B32671L8392+*** 2720 4400 4000

4.7 6.0 ×12.0 ×13.0 B32671L8472+*** 2720 4400 4000

B32671L

High V AC, high temperature (wound)

Page5of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

160 250 150 5.0 ×10.5 ×18.0 B32672L2154+*** 4680 5200 4000

220 6.0 ×11.0 ×18.0 B32672L2224+*** 3840 4400 4000

330 7.0 ×12.5 ×18.0 B32672L2334+*** 3320 3600 4000

470 8.5 ×14.5 ×18.0 B32672L2474+*** 2720 2800 2000

680 9.0 ×17.5 ×18.0 B32672L2684+*** 2560 2800 2000

1000 11.0 ×18.5 ×18.0 B32672L2105+*** 2200 1200

200 450 68 5.0 ×10.5 ×18.0 B32672L4683+*** 4680 5200 4000

100 5.0 ×10.5 ×18.0 B32672L4104+*** 4680 5200 4000

150 6.0 ×11.0 ×18.0 B32672L4154+*** 3840 4400 4000

220 7.0 ×12.5 ×18.0 B32672L4224+*** 3320 3600 4000

330 8.0 ×14.0 ×18.0 B32672L4334+*** 2920 3000 2000

470 9.0 ×17.5 ×18.0 B32672L4474+*** 2560 2800 2000

680 11.0 ×18.5 ×18.0 B32672L4684+*** 2200 1200

250 630 33 5.0 ×10.5 ×18.0 B32672L6333+*** 4680 5200 4000

47 5.0 ×10.5 ×18.0 B32672L6473+*** 4680 5200 4000

68 6.0 ×11.0 ×18.0 B32672L6683+*** 3840 4400 4000

100 7.0 ×12.5 ×18.0 B32672L6104+*** 3320 3600 4000

150 8.5 ×14.5 ×18.0 B32672L6154+*** 2720 2800 2000

220 9.0 ×17.5 ×18.0 B32672L6224+*** 2560 2800 2000

390 11.0 ×18.5 ×18.0 B32672L6394+*** 2200 1200

B32672L

High V AC, high temperature (wound)

Page6of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

250 1000 10 5.0 ×10.5 ×18.0 B32672L0103+*** 4680 5200 4000

15 5.0 ×10.5 ×18.0 B32672L0153+*** 4680 5200 4000

22 5.0 ×10.5 ×18.0 B32672L0223+*** 4680 5200 4000

33 6.0 ×11.0 ×18.0 B32672L0333+*** 3840 4400 4000

47 7.0 ×12.5 ×18.0 B32672L0473+*** 3320 3600 4000

68 8.5 ×14.5 ×18.0 B32672L0683+*** 2720 2800 2000

100 9.0 ×17.5 ×18.0 B32672L0104+*** 2560 2800 2000

150 11.0 ×18.5 ×18.0 B32672L0154+*** 2200 1200

500 1300 6.8 5.0 ×10.5 ×18.0 B32672L7682+*** 4680 5200 4000

10 5.0 ×10.5 ×18.0 B32672L7103+*** 4680 5200 4000

22 7.0 ×12.5 ×18.0 B32672L7223+*** 3320 3600 4000

33 8.5 ×14.5 ×18.0 B32672L7333+*** 2720 2800 2000

47 9.0 ×17.5 ×18.0 B32672L7473+*** 2560 2800 2000

68 11.0 ×18.5 ×18.0 B32672L7683+*** 2200 1200

600 1600 6.2 5.0 ×10.5 ×18.0 B32672L1622+*** 4680 5200 4000

6.8 5.0 ×10.5 ×18.0 B32672L1682+*** 4680 5200 4000

8.2 6.0 ×11.0 ×18.0 B32672L1822+*** 3840 4400 4000

10 6.0 ×11.0 ×18.0 B32672L1103+*** 3840 4400 4000

12 6.0 ×12.0 ×18.0 B32672L1123+*** 3840 4400 4000

15 7.0 ×12.5 ×18.0 B32672L1153+*** 3320 3600 4000

22 8.5 ×14.5 ×18.0 B32672L1223+*** 2720 2800 2000

33 9.0 ×17.5 ×18.0 B32672L1333+*** 2560 2800 2000

47 11.0 ×18.5 ×18.0 B32672L1473+*** 2200 1200

B32672L

High V AC, high temperature (wound)

Page7of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

700 2000 1.0 5.0 ×10.5 ×18.0 B32672L8102+*** 4680 5200 4000

1.2 5.0 ×10.5 ×18.0 B32672L8122+*** 4680 5200 4000

1.5 5.0 ×10.5 ×18.0 B32672L8152+*** 4680 5200 4000

2.2 5.0 ×10.5 ×18.0 B32672L8222+*** 4680 5200 4000

2.7 5.0 ×10.5 ×18.0 B32672L8272+*** 4680 5200 4000

3.3 5.0 ×10.5 ×18.0 B32672L8332+*** 4680 5200 4000

3.9 5.0 ×10.5 ×18.0 B32672L8392+*** 4680 5200 4000

4.7 5.0 ×10.5 ×18.0 B32672L8472+*** 4680 5200 4000

5.6 6.0 ×11.0 ×18.0 B32672L8562+*** 3840 4400 4000

6.2 6.0 ×11.0 ×18.0 B32672L8622+*** 3840 4400 4000

6.8 6.0 ×11.0 ×18.0 B32672L8682+*** 3840 4400 4000

8.2 6.0 ×12.0 ×18.0 B32672L8822+*** 3840 4400 4000

10 7.0 ×12.5 ×18.0 B32672L8103+*** 3320 3600 4000

12 8.5 ×14.5 ×18.0 B32672L8123+*** 2720 2800 2000

15 8.5 ×14.5 ×18.0 B32672L8153+*** 2720 2800 2000

22 9.0 ×17.5 ×18.0 B32672L8223+*** 2560 2800 2000

33 11.0 ×18.5 ×18.0 B32672L8333+*** 2200 1200

B32672L

High V AC, high temperature (wound)

Page8of39Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

VRMS

f≤1 kHz

VAC

VDC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series, intermediate capacitance values and closer tolerances on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K=±10%

J= ±5%

289 = Straight terminals, Ammo pack

189 = Straight terminals, Reel

003 = Straight terminals, untaped (lead length

3.2 ±0.3 mm)

000 = Straight terminals, untaped (lead length

61 mm)

900 2000 1.0 5.0 ×10.5 ×18.0 B32672L9102+*** 4680 5200 4000

1.2 6.0 ×11.0 ×18.0 B32672L9122+*** 3840 4400 4000

1.5 6.0 ×11.0 ×18.0 B32672L9152+*** 3840 4400 4000

2.2 7.0 ×12.5 ×18.0 B32672L9222+*** 3320 3600 4000

2.7 8.0 ×14.0 ×18.0 B32672L9272+*** 2920 3000 2000

3.3 8.5 ×14.5 ×18.0 B32672L9332+*** 2720 2800 2000

3.9 9.0 ×17.5 ×18.0 B32672L9392+*** 2560 2800 2000

4.7 9.0 ×17.5 ×18.0 B32672L9472+*** 2560 2800 2000

5.6 11.0 ×18.5 ×18.0 B32672L9562+*** 2200 1200

6.2 11.0 ×18.5 ×18.0 B32672L9622+*** 2200 1200

6.8 11.0 ×18.5 ×18.0 B32672L9682K*** 2200 1200

B32672L

High V AC, high temperature (wound)

Page9of39Please read Cautions and warnings and

Important notes at the end of this document.

Technical data

Reference standard: IEC 60384-16:2005 and AEC-Q200D. All data given atT=20°C, unless

otherwise specified.

Rated temperature TR+85 °C

Operating temperature

range

Max. operating temperature Top,max

Upper category temperature Tmax

Lower category temperature Tmin

Rated temperature TR

+125 °C

+110 °C

55 °C

+85 °C

Dissipation factor tan δ

(in 10-3)at20°C

(upper limit values)

at ≤27 nF 27 nF< CR≤0.1 μF0.1 μF<C

R≤1μF >1 μF

1 kHz 0.8 0.8 0.8 0.8

10 kHz 1.0 1.0 1.0 

100 kHz 2.0 3.0  

Insulation resistance Rins

or time constant

τ=C

RRins at 20 °C,

rel. humidity ≤65%

(minimum as-delivered

values)

100 GΩ(CR≤0.33 μF)

30000 s (CR> 0.33 μF)

DC test voltage 1.6 VR,2s

Category voltage VCTop (°C) DC voltage derating AC voltage derating

(continuous operation

with VDC or VAC atf≤1 kHz)

Top ≤85

85<Top≤110

VC=V

R(165Top)/80

VC,RMS =V

RMS

VC,RMS=VRMS (165Top)/80

Operating voltage Vop for Top (°C) DC voltage (max. hours) AC voltage (max. hours)

short operating periods Top ≤100 Vop = 1.25 VC(2000 h) Vop = 1.0 VC,RMS (2000 h)

(VDC or VAC at f ≤1 kHz) 100<Top≤125 Vop = 1.25 VC(1000 h) Vop = 1.0 VC,RMS (1000 h)

Biased humidity 1000h/40°C / 93% relative humidity with VR,DC

Limit values after test Capacitance change ΔC/C

Dissipation factor change Δtan δ

Insulation resistance Rins

≤5%

≤0.002 (at 1 kHz)

≥200 MΩ

Reliability:

Failure rate λ1 fit (≤110-9/h) at 0.5 VR,40°C

Service life tSL 200 000 h at 1.0 VR,85°C

For conversion to other operating conditions and temperatures, refer

to chapter "Quality, 2 Reliability".

Failure criteria:

Total failure Short circuit or open circuit

Failure due to variation Capacitance change ΔC/C> 10%

of parameters Dissipation factor tan δ>4upper limit values

Insulation resistance Rins < 1500 MΩ

B32671L, B32672L

High V AC, high temperature (wound)

Page 10 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Pulse handling capability

"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal

voltages, expressed in V/μs.

"k0" represents the maximum permissible pulse characteristic of the waveform applied to the

capacitor, expressed in V2/μs.

Note:

The values of dV/dt and k0provided below must not be exceeded in order to avoid damaging the

capacitor. These parameters are given for isolated pulses in such a way that the heat generated

by one pulse will be completely dissipated before applying the next pulse. For a train of pulses,

please refer to the curves of permissible AC voltage-current versus frequency.

dV/dt values

Lead spacing 10 mm

Type B32671L

VRMS (V AC) 200 250 500 600 700

VR(V DC) 400 630 1000 1000 1600 2000

CR(nF) dV/dt in V/μs

1.0      11000

1.2     6000 10000

1.5     5600 9500

2.2     5200 9000

2.7     5000 8600

3.3    4700 4700 8500

3.9    4300 4500 8200

4.7   810 3800 4000 8000

5.6    3400  

6.2    3200  

6.8   810 3100  

8.2    2700  

10   810 2500  

12    2300  

15 540 810   

22 400 540 810   

33 400 540    

47 400 540    

56 540    

68 400     

100 400     

B32671L, B32672L

High V AC, high temperature (wound)

Page 11 of 39Please read Cautions and warnings and

Important notes at the end of this document.

dV/dt values

Lead spacing 15 mm

Type B32672L

VRMS (V AC) 160 200 250 500 600 700 900

VR(V DC) 250 450 630 1000 1300 1600 2000 2000

CR(nF) dV/dt in V/μs

1.0       10000 15000

1.2       9400 14100

1.5       9000 13500

2.2       7500 11000

2.7       7100 10600

3.3       6800 10000

3.9       6000 9000

4.7       5500 8200

5.6       5000 7500

6.2      3600 4700 7000

6.8     1000 3500 4500 6700

8.2      3100 4200 

10    445 1000 2800 3900 

12      2600 3600 

15    445 2300 3300 

22    445 1000 2000 2900 

33   300 445 1000 1700 2300 

47   300 445 1000 1400  

56        

68 200 300 445 1000   

100 200 300 445    

150 170 200 300 445    

220 170 200 300     

330 170 200      

390   300     

470 170 200      

680 170 200      

1000 170       

B32671L, B32672L

High V AC, high temperature (wound)

Page 12 of 39Please read Cautions and warnings and

Important notes at the end of this document.

k0values

Lead spacing 10 mm

Type B32671L

VRMS (V AC) 200 250 500 600 700

VR(V DC) 400 630 1000 1000 1600 2000

CR(nF) k0in V2/μs

1.0      25000000

1.2     14400000 23000000

1.5     14000000 22500000

2.2     13800000 22000000

2.7     13600000 21500000

3.3    9400000 13300000 21000000

3.9    8600000 13100000 20900000

4.7   400000 8200000 12000000 20800000

5.6    7600000 

6.2    6800000 

6.8   400000 6200000 

8.2    5400000 

10   400000 5000000 

12    4600000 

15 200000 400000  

22 150000 200000 400000  

33 150000 200000   

47 150000 200000   

56 200000   

68 150000    

100 150000    

B32671L, B32672L

High V AC, high temperature (wound)

Page 13 of 39Please read Cautions and warnings and

Important notes at the end of this document.

k0values

Lead spacing 15 mm

Type B32672L

VRMS (V AC) 160 200 250 500 600 700 900

VR(V DC) 250 450 630 1000 1300 1600 2000 2000

CR(nF) k0in V2/μs

1.0       20300000 30000000

1.2       19600000 29400000

1.5       19200000 28000000

2.2       18600000 27500000

2.7       18200000 27300000

3.3       18000000 27000000

3.9       16800000 25200000

4.7       15800000 23500000

5.6       13100000 19500000

6.2      11520000 12700000 19000000

6.8     3000000 11200000 12300000 18400000

8.2      9920000 11800000 

10 1000000 3000000 8960000 11100000 

12      8320000 10600000 

15 1000000 7360000 10400000 

22 1000000 3000000 6400000 9300000 

33   500000 1000000 3000000 5440000 9000000 

47   500000 1000000 3000000 4480000  

56        

68 120000 500000 1000000 3000000   

100 120000 500000 1000000    

150 100000 120000 500000 1000000    

220 100000 120000 500000     

330 100000 120000      

390   500000     

470 100000 120000      

680 100000      

1000 100000       

B32671L, B32672L

High V AC, high temperature (wound)

Page 14 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Impedance Z versus frequency f

(typical values)

B32671L, B32672L

High V AC, high temperature (wound)

Page 15 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 10 mm

400 V DC/200 V AC 630 V DC/250 V AC

1000 V DC/250 V AC 1000 V DC/500 V AC

B32671L

High V AC, high temperature (wound)

Page 16 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 10 mm

1600 V DC/600 V AC 2000 V DC/700 V AC

B32671L

High V AC, high temperature (wound)

Page 17 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 15 mm

250 V DC/160 V AC 450 V DC/200 V AC

630 V DC/250 V AC 1000 V DC/250 V AC

B32672L

High V AC, high temperature (wound)

Page 18 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 15 mm

1300 V DC/500 V AC 1600 V DC/600 V AC

2000 V DC/700 V AC 2000 V DC/900 V AC

B32672L

High V AC, high temperature (wound)

Page 19 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 10 mm

400 V DC/200 V AC 630 V DC/250 V AC

1000 V DC/250 V AC 1000 V DC/500 V AC

B32671L

High V AC, high temperature (wound)

Page 20 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 10 mm

1600 V DC/600 V AC 2000 V DC/700 V AC

B32671L

High V AC, high temperature (wound)

Page 21 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 15 mm

250 V DC/160 V AC 450 V DC/200 V AC

630 V DC/250 V AC 1000 V DC/250 V AC

B32672L

High V AC, high temperature (wound)

Page 22 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Permissible current IRMS versus frequency f (for sinusoidal waveforms TA≤100 °C)

For TA>100 °C, please use derating factor FT.

Lead spacing 15 mm

1300 V DC/500 V AC 1600 V DC/600 V AC

2000 V DC/700 V AC 2000 V DC/900 V AC

B32672L

High V AC, high temperature (wound)

Page 23 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Maximum AC voltage (VRMS), current (IRMS) versus frequency and temperature for TA>100 °C

The graphs described in the previous section for the permissible AC voltage (VRMS) or current

(IRMS) versus frequency are given for a maximum ambient temperature TA≤100 ºC. In case of

higher ambient temperatures (TA), the self-heating (ΔT) of the component must be reduced to

avoid that temperature of the component (Top=T

A+ΔT) reaches values above maximum

operating temperature.The factor FTshall be applied in the following way:

And FTis given by the following curve:

B32671L, B32672L

High V AC, high temperature (wound)

Page 24 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Operation at overvoltages during heating and ignition of lamps (TA≤40 °C)

In lighting applications, the capacitors can be subjected to overvoltages during the heating and ig-

nition periods. An overvoltage occurs when the operation voltage exceeds the permissible

AC voltage at the resonant frequency fr.

For a repetitive application of on/off switching pulses (as for example in the life tests applied by

electronic ballast manufacturers), limits have to be imposed on the time periods under overvolt-

age and on the duty cycle, in order to keep the capacitance value within the required margins:

The overvoltage time tOV should be less than 1 sec.

The K0calculated in the overvoltage period (see general technical information) shall be lower

than the maximum K0provided.

The maximum duty cycle of the overvoltage is given by

where VRMS,ov is the RMS voltage during period tOV

and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr

(given by the “permissible AC voltage versus frequency f” graphics in theprevious pages).

The drift of capacitance depends on the Vpp attained, and the total time under overvoltage,

which is calculated in hours as follows:

(NitOV) / 3600

where Niis the number of overvoltage impulses and tOV is expressed in seconds.

The maximum drift of capacitance as a function of both parameters is provided graphically in the

following pages.

B32671L, B32672L

High V AC, high temperature (wound)

Page 25 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Estimation of the maximum drift of capacitance value in function of the number of total

hours overvoltage

Lead spacing 10 mm

500 V AC/1000 V DC 600 V AC/1600 V DC

B32671L

High V AC, high temperature (wound)

Page 26 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Estimation of the maximum drift of capacitance value in function of the number of total

hours overvoltage

Lead spacing 15 mm

600 V AC/1600 V DC 700 V AC/2000 V DC

B32672L

High V AC, high temperature (wound)

Page 27 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Testing and Standards

Test Reference Conditions of test Performance

requirements

Electrical

para-

meters

IEC 60384-16:2005 Voltage proof, 1.6 VR, 1 minute

Insulation resistance, Rins

Capacitance, C

Dissipation factor, tan δ

Within specified limits

Robust-

ness of ter-

minations

IEC

60068-2-21:2006

Tensile strength (test Ua1) Capacitance and tan δ

within specified limits

Wire diameter Tensile force

0.5<d1≤0.8 mm 10 N

Resis-

tance to

soldering

heat

IEC

60068-2-20:2008,

test Tb,

method 1A

Solder bath temperature at 260 ±5°C,

immersion for 10 seconds

ΔC/C0≤2%

Δtan δ≤0.002

Rapid

change of

tempera-

ture

IEC 60384-16:2005 TA= lower category temperature

TB= upper category temperature

Five cycles, duration t = 30 min.

Vibration IEC 60384-16:2005 Test Fc: vibration sinusoidal

Displacement: 0.75 mm

Accleration: 98 m/s2

Frequency: 10 Hz ... 500 Hz

Test duration: 3 orthogonal axes,

2 hours each axe

No visible damage

Bump IEC 60384-16:2005 Test Eb: Total 4000 bumps with

390 m/s2mounted on PCB

Duration: 6 ms

No visible damage

ΔC/C0≤2%

Δtan δ≤0.002

Rins ≥50% of initial limit

Climatic

sequence

IEC 60384-16:2005 Dry heat Tb / 16 h

Damp heat cyclic, 1st cycle

+55 °C / 24 h / 95% ... 100% RH

Cold Ta/2h

Damp heat cyclic, 5 cycles

+55 °C / 24 h / 95% ... 100% RH

No visible damage

ΔC/C0≤3%

Δtan δ≤0.001

Rins ≥50% of initial limit

Damp

heat,

steady

state

IEC 60384-16:2005 Test Ca

40 °C / 93% RH / 56 days

No visible damage

ΔC/C0≤3%

Δtan δ≤0.001

Rins ≥50% of initial limit

Advanced

biased

humidity

60 °C / 95% RH / 1000 hours with VR,DC No visible damage

ΔC/C0≤10%

Δtan δ≤0.002

Rins ≥50% of initial limit

B32671L, B32672L

High V AC, high temperature (wound)

Page 28 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Test Reference Conditions of test Performance

requirements

Endurance IEC 60384-16:2005 85 °C / 1.25 VR/ 2000 hours No visible damage

ΔC/C0≤5%

Δtan δ≤0.002

Rins ≥50% of initial limit

Endurance IEC 60384-16:2005 110 °C / 1.25 VC/ 2000 hours No visible damage

ΔC/C0≤10%

Δtan δ≤0.002

Rins ≥50% of initial limit

Mounting guidelines

1 Soldering

1.1 Solderability of leads

The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.

Before a solderability test is carried out, terminals are subjected to accelerated ageing (to

IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far

higher than the upper category temperature of the capacitors, the terminal wires should be cut off

from the capacitor before the ageing procedure to prevent the solderability being impaired by the

products of any capacitor decomposition that might occur.

Solder bath temperature 235 ±5°C

Soldering time 2.0 ±0.5 s

Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane

Evaluation criteria:

Visual inspection Wetting of wire surface by new solder ≥90%,

free-flowing solder

B32671L, B32672L

High V AC, high temperature (wound)

Page 29 of 39Please read Cautions and warnings and

Important notes at the end of this document.

1.2 Resistance to soldering heat

Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1.

Conditions:

Series Solder bath temperature Soldering time

MKT boxed (except 2.5 ×6.5 ×7.2 mm)

coated

uncoated (lead spacing >10 mm)

260 ±5°C 10 ±1s

MFP

MKP (lead spacing >7.5 mm)

MKT boxed (case 2.5 ×6.5 ×7.2 mm) 5±1s

MKP

MKT

(lead spacing ≤7.5 mm)

uncoated (lead spacing ≤10 mm)

insulated (B32559)

<4 s

recommended soldering

profile for MKT uncoated

(lead spacing ≤10 mm) and

insulated (B32559)

Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane

Shield Heat-absorbing board, (1.5 ±0.5) mm thick, between

capacitor body and liquid solder

Evaluation criteria:

Visual inspection No visible damage

ΔC/C0

2% for MKT/MKP/MFP

5% for EMI suppression capacitors

tan δAs specified in sectional specification

B32671L, B32672L

High V AC, high temperature (wound)

Page 30 of 39Please read Cautions and warnings and

Important notes at the end of this document.

1.3 General notes on soldering

Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-

gory temperature Tmax. Long exposure to temperatures above this type-related temperature limit

can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical

characteristics. For short exposures (as in practical soldering processes) the heat load (and thus

the possible effects on a capacitor) will also depend on other factors like:

Pre-heating temperature and time

Forced cooling immediately after soldering

Terminal characteristics:

diameter, length, thermal resistance, special configurations (e.g. crimping)

Height of capacitor above solder bath

Shadowing by neighboring components

Additional heating due to heat dissipation by neighboring components

Use of solder-resist coatings

The overheating associated with some of these factors can usually be reduced by suitable coun-

termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced

cooling process may possibly have to be included.

EPCOS recommendations

As a reference, the recommended wave soldering profile for our film capacitors is as follows:

B32671L, B32672L

High V AC, high temperature (wound)

Page 31 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Body temperature should follow the description below:

MKP capacitor

During pre-heating: Tp≤110 °C

During soldering: Ts≤120 °C, ts≤45 s

MKT capacitor

During pre-heating: Tp≤125 °C

During soldering: Ts≤160 °C, ts≤45 s

When SMD components are used together with leaded ones, the film capacitors should not pass

into the SMD adhesive curing oven. The leaded components should be assembled after the SMD

curing step.

Leaded film capacitors are not suitable for reflow soldering.

In order to ensure proper conditions for manual or selective soldering, the body temperature of

the capacitor (Ts) must be ≤120 °C.

One recommended condition for manual soldering is that the tip of the soldering iron should

be <360 °C and the soldering contact time should be no longer than 3 seconds.

For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following mea-

sures are recommended:

pre-heating to not more than 110 °C in the preheater phase

rapid cooling after soldering

Please refer to EPCOS Film Capacitor Data Book in case more details are needed.

B32671L, B32672L

High V AC, high temperature (wound)

Page 32 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Cautions and warnings

Do not exceed the upper category temperature (UCT).

Do not apply any mechanical stress to the capacitor terminals.

Avoid any compressive, tensile or flexural stress.

Do not move the capacitor after it has been soldered to the PC board.

Do not pick up the PC board by the soldered capacitor.

Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified

lead spacing.

Do not exceed the specified time or temperature limits during soldering.

Avoid external energy inputs, such as fire or electricity.

Avoid overload of the capacitors.

Consult us if application is with severe temperature and humidity condition.

There are no serviceable or repairable parts inside the capacitor. Opening the capacitor or

any attempts to open or repair the capacitor will void the warranty and liability of EPCOS.

Please note that the standards referred to in this publication may have been revised in the

meantime.

The table below summarizes the safety instructions that must always be observed. A detailed de-

scription can be found in the relevant sections of the chapters "General technical information" and

"Mounting guidelines".

Topic Safety information Reference chapter

"General technical

information"

Storage

conditions

Make sure that capacitors are stored within the specified

range of time, temperature and humidity conditions.

4.5

"Storage conditions"

Flammability Avoid external energy, such as fire or electricity (passive

flammability), avoid overload of the capacitors (active

flammability) and consider the flammability of materials.

5.3

"Flammability"

Resistance to

vibration

Do not exceed the tested ability to withstand vibration.

The capacitors are tested to IEC 60068-2-6:2007.

EPCOS offers film capacitors specially designed for

operation under more severe vibration regimes such as

those found in automotive applications. Consult our

catalog "Film Capacitors for Automotive Electronics".

5.2

"Resistance to

vibration"

Topic Safety information Reference chapter

"Mounting guidelines"

Soldering Do not exceed the specified time or temperature limits

during soldering.

1 "Soldering"

Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning"

B32671L, B32672L

High V AC, high temperature (wound)

Page 33 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Topic Safety information Reference chapter

"Mounting guidelines"

Embedding of

capacitors in

finished

assemblies

When embedding finished circuit assemblies in plastic

resins, chemical and thermal influences must be taken

into account.

Caution: Consult us first, if you also wish to embed other

uncoated component types!

3 "Embedding of

capacitors in finished

assemblies"

Display of ordering codes for EPCOS products

The ordering code for one and the same product can be represented differently in data sheets,

data books, other publications and the website of EPCOS, or in order-related documents such as

shipping notes, order confirmations and product labels. The varying representations of the or-

dering codes are due to different processes employed and do not affect the specifications

of the respective products. Detailed information can be found on the Internet under

www.epcos.com/orderingcodes.

B32671L, B32672L

High V AC, high temperature (wound)

Page 34 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Symbols and terms

Symbol English German

αHeat transfer coefficient Wärmeübergangszahl

αCTemperature coefficient of capacitance Temperaturkoeffizient der Kapazität

ACapacitor surface area Kondensatoroberfläche

βCHumidity coefficient of capacitance Feuchtekoeffizient der Kapazität

CCapacitance Kapazität

CRRated capacitance Nennkapazität

ΔCAbsolute capacitance change Absolute Kapazitätsänderung

ΔC/C Relative capacitance change (relative

deviation of actual value)

Relative Kapazitätsänderung (relative

Abweichung vom Ist-Wert)

ΔC/CRCapacitance tolerance (relative deviation

from rated capacitance)

Kapazitätstoleranz (relative Abweichung

vom Nennwert)

dt Time differential Differentielle Zeit

ΔtTime interval Zeitintervall

ΔTAbsolute temperature change

(self-heating)

Absolute Temperaturänderung

(Selbsterwärmung)

Δtan δAbsolute change of dissipation factor Absolute Änderung des Verlustfaktors

ΔVAbsolute voltage change Absolute Spannungsänderung

dV/dt Time differential of voltage function (rate

of voltage rise)

Differentielle Spannungsänderung

(Spannungsflankensteilheit)

ΔV/ΔtVoltage change per time interval Spannungsänderung pro Zeitintervall

EActivation energy for diffusion Aktivierungsenergie zur Diffusion

ESL Self-inductance Eigeninduktivität

ESR Equivalent series resistance Ersatz-Serienwiderstand

fFrequency Frequenz

f1Frequency limit for reducing permissible

AC voltage due to thermal limits

Grenzfrequenz für thermisch bedingte

Reduzierung der zulässigen

Wechselspannung

f2Frequency limit for reducing permissible

AC voltage due to current limit

Grenzfrequenz für strombedingte

Reduzierung der zulässigen

Wechselspannung

frResonant frequency Resonanzfrequenz

FDThermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur

Diffusion

FTDerating factor Deratingfaktor

iCurrent (peak) Stromspitze

ICCategory current (max. continuous

current)

Kategoriestrom (max. Dauerstrom)

B32671L, B32672L

High V AC, high temperature (wound)

Page 35 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Symbol English German

IRMS (Sinusoidal) alternating current,

root-mean-square value

(Sinusförmiger) Wechselstrom

izCapacitance drift Inkonstanz der Kapazität

k0Pulse characteristic Impulskennwert

LSSeries inductance Serieninduktivität

λFailure rate Ausfallrate

λ0Constant failure rate during useful

service life

Konstante Ausfallrate in der

Nutzungsphase

λtest Failure rate, determined by tests Experimentell ermittelte Ausfallrate

Pdiss Dissipated power Abgegebene Verlustleistung

Pgen Generated power Erzeugte Verlustleistung

QHeat energy Wärmeenergie

ρDensity of water vapor in air Dichte von Wasserdampf in Luft

RUniversal molar constant for gases Allg. Molarkonstante für Gas

ROhmic resistance of discharge circuit Ohmscher Widerstand des

Entladekreises

RiInternal resistance Innenwiderstand

Rins Insulation resistance Isolationswiderstand

RPParallel resistance Parallelwiderstand

RSSeries resistance Serienwiderstand

Sseverity (humidity test) Schärfegrad (Feuchtetest)

tTime Zeit

TTemperature Temperatur

τTime constant Zeitkonstante

tan δDissipation factor Verlustfaktor

tan δDDielectric component of dissipation

factor

Dielektrischer Anteil des Verlustfaktors

tan δPParallel component of dissipation factor Parallelanteil des Verlfustfaktors

tan δSSeries component of dissipation factor Serienanteil des Verlustfaktors

TATemperature of the air surrounding the

component

Temperatur der Luft, die das Bauteil

umgibt

Tmax Upper category temperature Obere Kategorietemperatur

Tmin Lower category temperature Untere Kategorietemperatur

tOL Operating life at operating temperature

and voltage

Betriebszeit bei Betriebstemperatur und

-spannung

Top Operating temperature, TA+ΔT Beriebstemperatur, TA+ΔT

TRRated temperature Nenntemperatur

Tref Reference temperature Referenztemperatur

tSL Reference service life Referenz-Lebensdauer

B32671L, B32672L

High V AC, high temperature (wound)

Page 36 of 39Please read Cautions and warnings and

Important notes at the end of this document.

Symbol English German

VAC AC voltage Wechselspannung

VCCategory voltage Kategoriespannung

VC,RMS Category AC voltage (Sinusförmige)

Kategorie-Wechselspannung

VCD Corona-discharge onset voltage Teilentlade-Einsatzspannung

Vch Charging voltage Ladespannung

VDC DC voltage Gleichspannung

VFB Fly-back capacitor voltage Spannung (Flyback)

ViInput voltage Eingangsspannung

VoOutput voltage Ausgangssspannung

Vop Operating voltage Betriebsspannung

VpPeak pulse voltage Impuls-Spitzenspannung

Vpp Peak-to-peak voltage Impedance Spannungshub

VRRated voltage Nennspannung

RAmplitude of rated AC voltage Amplitude der Nenn-Wechselspannung

VRMS (Sinusoidal) alternating voltage,

root-mean-square value

(Sinusförmige) Wechselspannung

VSC S-correction voltage Spannung bei Anwendung "S-correction"

Vsn Snubber capacitor voltage Spannung bei Anwendung

"Beschaltung"

ZImpedance Scheinwiderstand

Lead spacing Rastermaß

B32671L, B32672L

High V AC, high temperature (wound)

Page 37 of 39Please read Cautions and warnings and

Important notes at the end of this document.

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

Important notes

Page 38 of 39

7. Our manufacturing sites serving the automotive business apply the IATF 16949

standard. The IATF certifications confirm our compliance with requirements regarding the

quality management system in the automotive industry. Referring to customer requirements

and customer specific requirements (“CSR”) TDK always has and will continue to have the

policy of respecting individual agreements. Even if IATF 16949 may appear to support the

acceptance of unilateral requirements, we hereby like to emphasize that only requirements

mutually agreed upon can and will be implemented in our Quality Management System.

For clarification purposes we like to point out that obligations from IATF 16949 shall only

become legally binding if individually agreed upon.

8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP,

CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD,

MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine,

PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV,

ThermoFuse, WindCap are trademarks registered or pending in Europe and in other coun-

tries. Further information will be found on the Internet at www.epcos.com/trademarks.

Release 2018-06

Important notes

Page 39 of 39