■性能 Performance
■負荷軽減曲線 Derating Curve
周囲温度70℃以上で使用される場合は、上図負荷軽減曲線
に従って、定格電力を軽減して御使用ください。
For resistors operated at an ambient temperature of 70℃ or
above, a power rating shall be derated in accordance with
the above derating curve.
100
80
60
40
20
0
-60 -40 -20 0204060
70 155-55
80 100 120 140 160
Percentratedpower
周囲温度 Ambienttemperature(℃)
あ1
あ1
定格電力比(%)
1E/0.125W
1J/0.2W
2A/0.25W
2B/0.33W
2E/0.5W
■ワンパルス限界電力曲線
One-Pulse Limiting Electric Power
角形面実装抵抗器
Flat Chip Resistors
本カタログに掲載の仕様は予告なく変更する場合があります。ご注文およびご使用前に納入仕様書で内容をご確認ください。 Apr.2018
車載機器、医療機器、航空機器など人命に関わったり、あるいは甚大な損害を引き起こす可能性のある機器へのご使用を検討される場合には、必ず事前にご相談ください。
Specificationsgivenhereinmaybechangedatanytimewithoutpriornotice.Pleaseconfirmtechnicalspecificationsbeforeyouorderand/oruse.
Contactoursalesrepresentativesbeforeyouuseourproductsforapplicationsincludingautomotives,medicalequipmentandaerospaceequipment.
Malfunctionorfailureoftheproductsinsuchapplicationsmaycauselossofhumanlifeorseriousdamage. www.koaglobal.com
0.1
1.0
10.0
100.0
1000.0
0.001 0.01 0.1 110 100 1000
ワンパルス限界電力(W)
One-pulselimitingelectricpower
パルス持続時間 Pulseduration(ms)
1
10
100
1000
0.001 0.01 0.1 110 100 1000
SG73P2E
SG73P1J
SG73P2A
SG73P2B
ワンパルス限界電力(W)
One-pulselimitingelectricpower
パルス持続時間 Pulseduration(ms)
SG73P2E
SG73P2B
SG73P2A
SG73P1J
SG73P1E
SG73P
試験項目
TestItems
規格値 PerformanceRequirements
ΔR±(%+0.1Ω) 試験方法
TestMethods
保証値 Limit 代表値 Typical
抵抗値
Resistance
規定の許容差内
Withinspecifiedtolerance — 25℃
抵抗温度係数
T.C.R.
規定値内
WithinspecifiedT.C.R. — +25℃/−55℃and+25℃/+125℃
過負荷(短時間)
Overload(Shorttime) 2 0.5
定格電圧×2.5倍を5秒印加(2A:0.4W、0.5W、2B:0.75W、2E:0.75W定格電圧×2倍)
Ratedvoltage×2.5for5s(2A:0.4W,0.5W,2B:0.75W,2E:0.75WRatedvoltage×2for5s)
はんだ耐熱性
Resistancetosolderingheat 1 0.75 260℃±5℃,10s±1s
温度急変
Rapidchangeoftemperature 0.5 0.3 −55℃(30min.)/+125℃(30min.)100cycles
耐湿負荷
Moistureresistance 3 0.75 40℃±2℃,90%〜95%RH,1000h
1.5時間ON/0.5時間OFFの周期1.5hON/0.5hOFFcycle
70℃での耐久性
Enduranceat70℃ 3 0.75 70℃±2℃,1000h
1.5時間ON/0.5時間OFFの周期1.5hON/0.5hOFFcycle
高温放置
Hightemperatureexposure 1 0.3 +155℃,1000h
100
80
60
40
20
0
-60 -40 -20 0204060
12 5 155-55
8 0 100 120 140 160
Percentratedpower
端子部温度 Terminalparttemperature(℃)
あ1
あ1
定格電力比(%)
1E/0.125W
1J/0.2W
2A/0.25W
2B/0.33W
2E/0.5W
端子部温度Terminalparttemperature 端子部温度Terminalparttemperature周囲温度Ambienttemperature
上記の端子部温度以上で使用される場合は、負荷軽減曲線に従って定格電力を軽減してご使用ください。
※2、※3の定格電力で使用される場合は右側の端子部温度による負荷軽減曲線をご使用ください。
※ ご使用方法につきましては巻頭の“端子部温度の負荷軽減曲線の紹介”を参照願います。
For resistors operated terminal part temperature of described for each size or above, a power rating shall be
derated in accordance with derating curve.
If you want to use at the rated power of ※2 or ※3, please use the derating curves based on the terminal part
temperature of right side.
※ Please refer to“Introduction of the derating curves based on the terminal part temperature”on the beginning
of our catalog before use.
100
80
60
40
20
0
-60 -40 -20 0204060
1 0 51 1 0
155-55
8 0 100
120
140 160
Percentratedpower
端子部温度 Terminalparttemperature(℃)
1 2 5
あ1
あ1
定格電力比(%)
2E/0.75W(110℃)
1J/0.33W(125℃)
2A/0.5W(100℃)
1E/0.2W,2B/0.75W(105℃)
■使用上の注意事項 Precautions for Use
● チップ抵抗器の基材はアルミナです。実装すると基板との熱膨張係数の違いから、ヒートサイクル等の熱ストレスを繰り返し与えた
場合、接合部のはんだ(はんだフィレット部)にクラックが発生する場合があります。周囲温度の変動が大きく繰り返される場合や、
負荷のオンオフが繰り返される場合は、クラックの発生に注意が必要です。熱ストレスによるクラックの発生は、実装されるランド
の大きさ、はんだ量、実装基板の放熱性等に左右されますので、周囲温度の大きな変化や負荷のオンオフのような使用条件が想定さ
れる場合は、十分注意して設計してください。
● The substrate of chip resistors is alumina. Cracks may occur at the connection of solder (solder fillet portion) due to the difference of
the coefficient of thermal expansion from a mounting board when heat stress like heat cycle, etc. are repeatedly given to them. Care
should be taken to the occurrence of the cracks when the change in ambient temperature or ON/OFF of load is repeated. The
occurrence of the crack by heat stress may be influenced by the size of a pad, solder volume, heat radiation of mounting board etc., so
please pay careful attention to designing when a big change in ambient temperature and conditions for use like ON/OFF of load can
be assumed.
印加可能な電圧の上限は最高過負荷電圧になります。
パルスを連続して印加する場合の耐性はお問い合わせください。
The maximum applicable voltage is equal to the max. overload voltage.
Please ask us about the resistance characteristic of continuous applied pulse.