Evaluation Board for 14-/16-Bit, Serial Input, VOUT NanoDACsTM EVAL-AD5040EB/EVAL-AD506xEB FEATURES The AD5040/AD506x devices offer a relative accuracy specification of 1 LSB and operation is guaranteed monotonic with a 1 LSB DNL specification. Full-featured evaluation board for the AD5040/AD506x Operates from single 2.7 V to 5.5 V supplies On-board reference Direct hookup to USB port of PC PC software for control of DAC Power-on reset to midscale or zero scale 3 power-down functions The AD5040 and AD506x devices use a versatile 3-wire serial interface that operates at clock rates up to 30 MHz and are compatible with standard SPI(R), QSPITM, MICROWIRETM, and DSP interface standards. The reference for the AD5040 and AD506x devices is supplied from an external VREF pin. A reference buffer is also provided on-chip. The AD5040/AD506x incorporate a power-on reset circuit that ensures the DAC output powers up to midscale or zero scale and remains there until a valid write occurs. PACKAGE CONTENTS AD5040/AD506x evaluation board AD5040/AD506x device 3 V reference (ADR423) CD including Self-installing software that allows you to control the DAC and exercise all functions of the device Electronic version of device data sheet Electronic version of EVAL-AD5040EB/EVAL-AD506xEB data sheet OP97 op amp (provided with EVAL-AD5063 only) The AD5040 and the AD506x devices contain a power-down feature that reduces the current consumption of the device and provides software-selectable output loads while in power-down mode. The AD5061 is a low power, single 16-bit buffered voltage-out DAC. The AD5061 part offers a relative accuracy specification of 4 LSB, and operation is guaranteed monotonic with a 1 LSB DNL specification. The AD5063 is a low power, single 16-bit buffered voltage-out DAC and comes with on-board resistors in a 10-lead MSOP, allowing bipolar signals to be generated with an output amplifier. The AD5062 is a low power, single 16-bit unbuffered voltage-out DAC. The AD5062 offers a relative accuracy specification of 1 LSB, and operation is guaranteed monotonic with a 1 LSB DNL specification. An external reference can also be applied via an SMB input connector. The evaluation board is powered via terminal blocks. GENERAL DESCRIPTION This data sheet describes the evaluation board for evaluating the AD5040, AD5060, AD5061, AD5062, and AD5063 nanoDACs. These devices are low power, single 14-/16-bit buffered voltage-out DACs. Operating from single 2.7 V to 5.5 V supplies, the devices are well suited to battery-powered and other applications. FUNCTIONAL BLOCK DIAGRAM POWER SUPPLY INPUTS USB CONNECTOR VDD REFIN AGND 3V VOLTAGE REFERENCE EEPROM CONTROLLER CY7C68013 VDD BUFFER REFIN SPI AD5040/AD506x VOUT SMB CONNECTORS AGND DACGND 06141-001 14-/16-BIT DAC Figure 1. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved. EVAL-AD5040EB/EVAL-AD506xEB TABLE OF CONTENTS Features .............................................................................................. 1 Installing the Software ..................................................................4 Package Contents.............................................................................. 1 Operating the Software.................................................................4 General Description ......................................................................... 1 Schematics and Artwork ..................................................................5 Functional Block Diagram .............................................................. 1 PCB Layers for EVAL-AD5040EB/EVAL-AD5060EB/ EVAL-AD5061EB/EVAL-AD5062EB.........................................8 Revision History ............................................................................... 2 Evaluation Board Hardware ............................................................ 3 Evaluation Board Link Configuraton ........................................ 3 Setup Conditions .......................................................................... 3 Evaluation Board Interfacing...................................................... 3 Sockets ........................................................................................... 3 PCB Layers for EVAL-AD5063EB ..............................................9 Ordering Information.................................................................... 10 Bills of Materials ......................................................................... 10 Ordering Guide .......................................................................... 12 ESD Caution................................................................................ 12 Connectors .................................................................................... 3 Evaluation Board Software .............................................................. 4 REVISION HISTORY 7/06--Revision 0: Initial Version Rev. 0 | Page 2 of 12 EVAL-AD5040EB/EVAL-AD506xEB EVALUATION BOARD HARDWARE The evaluation board for the AD5040/AD506x requires a single positive supply (+2.7 V to +5.5 V). The evaluation board for the AD5063 requires a single negative supply, such as -5 V, for the external on-board op amp in order to generate a bipolar signal. A +5 VDD and -5 VSS supply are required to power the output amplifier in the AD5063, if the user requires a bipolar signal. The +5 V VDD is used to power the DAC. All supplies are decoupled to ground with 10 F tantalum and 0.1 F ceramic capacitors. Table 2. AD5040/AD506x Pin Configuration Mnemonic VDD VREF DACGND VOUT SYNC EVALUATION BOARD LINK CONFIGURATON The three link options (LK1, LK2, and LK3) must be set before using the evaluation board. LK1 This sets the power to the Cypress USB microcontroller that controls the USB section of the chip. The supply for the microcontroller can be provided from an external supply or from the computer via the USB interface. Using the computer to set the supply, set Link 1 to Position A. To use an external supply, set the link to Position B. LK2 Link 2 connects the on chip reference to the Reference pin on the DAC. If you are using the ADR423 to provide the reference to the DAC, then Link 2 must be set. SCLK DIN AGND INV 1 RFB11 1 LK3 Link 3 is normally connected. This shows proper connection of the USB chip. Function Power supply input. Devices can operate from 2.7 V to 5.5 V and VDD, and should be decoupled to GND. Reference voltage input. Ground input to the DAC. Analog output voltage from DAC. Level triggered control input (active low). This is the frame synchronization signal for the input data. When SYNC goes low, it enables the input shift register and data is transferred in on the falling edges of the following clocks. The DAC is updated following the 16th clock cycle unless SYNC is taken high before this edge in which case the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the DAC. Serial clock input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates up to 30 MHz. Serial data input. This device has a 16-/24-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. Ground reference point for analog circuitry on part. Connected to the internal scaling resistors of the DAC. Connect the INV pin to the external op amp's inverting input in bipolar mode. Feedback resistor. In bipolar mode, connect this pin to the external op amp circuit. For AD5063 only. SOCKETS The J3 and J6 sockets are described in Table 3. Table 3. Socket Functions SETUP CONDITIONS Care should be taken before applying power and signals to the evaluation board to ensure that all link positions are as per the required operating mode. Table 1 shows the position in which all the links are set when the evaluation board is packaged. Socket J3 J6 Function Subminiature BNC socket for the DAC output. Subminiature BNC socket for the reference output. CONNECTORS Table 1. Initial Link and Switch Positions The evaluation board connectors are described in Table 4. Link No. LK1 LK2 Initial Position Set to Position A Closed Table 4. Connector Function LK3 Closed Function Power supplied from computer. Reference supplied to Reference pin from ADR423. USB cable connected. EVALUATION BOARD INTERFACING Connector Functions J1 USB connector. PCB-mounting terminal block. Supplies the digital power supply to the microcontroller. PCB-mounting SMB connector. Provides connection to on-board reference output voltage. PCB-mounting terminal block. Provides the reference power supply. PCB-mounting terminal block. Provides the power supply to the AD5040/AD506x. PCB-mounting terminal block. Provides connection to the DAC RFB pin. J2 J3, J6 The AD5040/AD5060/AD5061/AD5062 have 8 pins while the AD5063 has 10 pins as described in Table 2. Note that the last two entries in Table 2 (Pin INV and Pin RFB) apply only to the AD5063. Communication to the devices is accomplished via the Cypress CY7C63013 microcontroller Pin 45, Pin 46, and Pin 47. J4, J71 J5 J91 1 For AD5063 only. Rev. 0 | Page 3 of 12 EVAL-AD5040EB/EVAL-AD506xEB EVALUATION BOARD SOFTWARE INSTALLING THE SOFTWARE 3. Select how the device should operate. Choose Normal to operate the device in normal mode. For power-down mode, choose one of the three available options (Tri-State, 100 kOhm to GND or 1 kOhm to GND) as shown in Figure 3. 4. Enter the DAC code in either decimal or hex code. Select the field populated with zeroes (0000) for decimal or Hex for hex. The AD5040 accepts a 16-bit command whereas AD506x accepts a 24-bit command. 5. Select Update DAC to update DAC output. The AD5040/AD506x evaluation kit includes self-installing software on CD-ROM. The software is compatible with Microsoft(R) Windows(R) 95 or higher. Install the evaluation board software before connecting the evaluation board to the USB port of the PC. This ensures the evaluation board is correctly recognized when connected to the PC. 1. Start the Windows operating system and insert the CD-ROM. The installation software launches automatically. If it does not, use Windows Explorer to locate the file setup.exe on the CD-ROM. Select this file to start the installation procedure. 2. At the prompt, select a destination directory, which is C:\Program Files\Analog Devices\AD506X by default. Once the directory is selected, the installation procedure copies the files into the relevant directories on the hard drive. The installation program creates a program group called Analog Devices with subgroup AD506X in the Start menu of the taskbar. OPERATING THE SOFTWARE Once the installation procedure is complete, select the AD5040/60/61/62/63 icon to start the program. 2. Choose the part to be tested as shown in Figure 2. 06141-003 1. 06141-002 Figure 3. DAC Operation Selection Figure 2. Device Selection Rev. 0 | Page 4 of 12 EVAL-AD5040EB/EVAL-AD506xEB SCHEMATICS AND ARTWORK U5 06141-004 EVAL-AD5040/ AD5060/ AD5061/ AD5062 Figure 4. Evaluation Board Schematic for EVAL-AD5040/AD5060/AD5061/AD5062 Rev. 0 | Page 5 of 12 06141-005 EVAL-AD5040EB/EVAL-AD506xEB Figure 5. Evaluation Board Schematic for EVAL-AD5063 Rev. 0 | Page 6 of 12 06141-006 EVAL-AD5040EB/EVAL-AD506xEB Figure 6. Evaluation Board Schematic for AD5040/AD506x Controller Rev. 0 | Page 7 of 12 EVAL-AD5040EB/EVAL-AD506xEB 06141-010 06141-011 PCB LAYERS FOR EVAL-AD5040EB/EVAL-AD5060EB/EVAL-AD5061EB/EVAL-AD5062EB Figure 7. EVAL-AD5040EB/AD5060EB/AD5061EB/AD5062EB-- Component Side Artwork 06141-012 Figure 9. EVAL-AD5040EB/AD5060EB/AD5061EB/AD5062EB-- Component Side View (Top) Figure 8. EVAL-AD5040EB/AD5060EB/AD5061EB/AD5062EB-- Solder-Side Artwork Rev. 0 | Page 8 of 12 EVAL-AD5040EB/EVAL-AD506xEB 06141-008 06141-007 PCB LAYERS FOR EVAL-AD5063EB Figure 12. EVAL-AD603EB--Component Side View (Top) 06141-009 Figure 10. EVAL-AD5063EB --Component Side Artwork Figure 11. EVAL-AD5063EB--Solder-Side Artwork Rev. 0 | Page 9 of 12 EVAL-AD5040EB/EVAL-AD506xEB ORDERING INFORMATION BILLS OF MATERIALS Table 5. EVAL-AD5040EB/EVAL-AD5060EB/EVAL-AD5061EB/EVAL-AD5062EB Bill of Materials Qty. 2 24 3 1 2 3 1 2 3 1 1 1 1 1 Name C1, C2 C3 to C8, C10, C12, C13, C16, C17, C19, C22 to C25, C27, C28, C31 to C36 C9, C11, C14, C15, C18, C20, C21, C26, C29, C30 D1 J1 J2, J4-1, J4-2, J5-1, J5-2, J7 J3, J6, J9 LK1 LK2, LK3 R1, R2, R6 R3 R4, R5 T1, T2, T3 U1 U2 U3 U4 U5 1 1 1 U6 U7 Y1 10 1 1 6 Part Type Capacitor Capacitor Part Description 603 603 Stock Code FEC 722-005 FEC 499-675 Capacitor (tantalum, polarized) LED USB Power connector CAP\TAJ_A FEC 197-014 LED-0805 USB_RECPTACLE_B CON\POWER FEC 359-9681 FEC 152-754 FEC 151-785 PCB Jack Jumper_2 SIP-2P 603 603 603 Testpoint SSOP56 SO8NB 3.3 V Regulator SO8NB MSO10 FEC 310-682 FEC 148-535 and FEC 150-411 (36-pin strip) FEC 511-705 and FEC 150-411 (36-pin strip) FEC 911-276 FEC 911-239 FEC 911-471 FEC 240-333 Digikey 428-1332-ND Digikey 24LC64B-1/SN-ND ADP3303AR-3.3 ADR425 AD5040/AD5060/AD5061/AD5062 Quad Buffer 3.3 V Regulator HC49 FEC 492-395 ADP3303AR-3.3 FEC 569-860 SMA Jumper_2 Jumper Resistor Resistor Resistor Testpoint CY7C68013 24LC64 ADP3303-3.3 ADR425 AD5040/AD5060/ AD5061/AD5062 74HC125 ADP3303 XTAL Rev. 0 | Page 10 of 12 EVAL-AD5040EB/EVAL-AD506xEB Table 6. EVAL-AD5063EB Bill of Materials Qty. 2 24 1 1 4 Name C1, C2 C3 to C8, C10, C12, C13, C16, C17, C19, C22 to C25, C27, C28, C31 to C36 C9, C11, C14, C15, C18, C20, C21, C26, C29, C30 D1 J1 J2, J4, J5, J7 3 1 2 3 1 2 3 1 1 1 1 1 1 1 1 1 J3, J6, J9 LK1 LK2, LK3 R1, R2, R6 R3 R4, R5 T1, T2, T3 U1 U2 U3 U4 U5 U6 U7 U8 Y1 10 Part Type Capacitor Capacitor Part Description 603 603 Stock Code FEC 722-005 FEC 499-675 Capacitor+ CAP\TAJ_A FEC 197-014 LED USB Power connector SMA Jumper_2 Jumper Resistor Resistor Resistor Testpoint CY7C68013 24LC64 ADP3303-3.3 ADR423 AD5063BRMZ 74HC125 ADP3303 OP97 XTAL LED-0805 USB_RECPTACLE_B CON\POWER FEC 359-9681 FEC 152-754 FEC 151-785 PCB Jack Jumper_2 SIP-2P 603 603 603 Testpoint SSOP56 SO8NB SO8NB SO8NB MSO10 Quad Buffer 3.3 V Regulator SO8NB HC49 FEC 310-682 FEC 148-535 and FEC 150-411 (36-pin strip) FEC 511-705 and FEC 150-411 (36-pin strip) FEC 911-276 FEC 911-239 FEC 911-471 FEC 240-333 Digikey 428-1332-ND Digikey 24LC64B-1/SN-ND ADP3303AR-3.3 ADR425 AD5063BRMZ FEC 492-395 ADP3300ART-5 OP97FS FEC 569-860 Rev. 0 | Page 11 of 12 EVAL-AD5040EB/EVAL-AD506xEB ORDERING GUIDE Model EVAL-AD5040EB EVAL-AD5060EB EVAL-AD5061EB EVAL-AD5062EB EVAL-AD5063EB Description Evaluation Board Evaluation Board Evaluation Board Evaluation Board Evaluation Board ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. (c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. EB06141-0-7/06(0) Rev. 0 | Page 12 of 12