DS3884A
DS3884A BTL Handshake Transceiver
Literature Number: SNOS655B
DS3884A
BTL Handshake Transceiver
General Description
The DS3884A is one in a series of transceivers designed
specifically for the implementation of high performance Fu-
turebus+ and proprietary bus interfaces. The DS3884A is a
BTL 6-bit Handshake Transceiver designed to conform to
IEEE 1194.1 (Backplane Transceiver Logic—BTL) as speci-
fied in the IEEE 896.2 Futurebus+ specification.
Features
nFast propagation delay (3 ns typ)
n6-bit BTL transceiver
nSelective receiver glitch filtering (FR1–FR3)
nMeets 1194.1 Standard on Backplane Transceiver Logic
(BTL)
nSupports live insertion
nGlitch free power-up/down protection
nTypically less than 5 pF bus-port capacitance
nLow Bus-port voltage swing (typically 1V) at 80 mA
nTTL compatible driver and control inputs
nSeparate TTL I/O
nOpen collector bus-port outputs allow Wired-OR
connection
nControlled rise and fall time to reduce noise coupling to
adjacent lines
nBuilt in Bandgap reference with separate QV
CC
and
QGND pins for precise receiver thresholds
nExceeds 2 kV ESD testing (Human Body Model)
nIndividual Bus-port ground pins
nProduct offered in PQFP package styles
Connection Diagram
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
DS011460-1
Order Number DS3884AVF
See NS Package VF44B
August 2000
DS3884A BTL Handshake Transceiver
© 2001 National Semiconductor Corporation DS011460 www.national.com
Logic Diagram
DS011460-3
DS3884A
www.national.com 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage 6.5V
Control Input Voltage 6.5V
Driver Input and Receiver Output 5.5V
Receiver Input Current ±15 mA
Bus Termination Voltage 2.4V
Power Dissipation at 25˚C
PQFP 1.3W
Derate PQFP Package 11.1 mW/˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature
(Soldering, 4 seconds): 260˚C
Recommended Operating
Conditions
Supply Voltage, V
CC
4.5V–5.5V
Bus Termination Voltage (V
T
) 2.06V–2.14V
Operating Free Air Temperature 0˚C to 70˚C
DC Electrical Characteristics (Notes 2, 3)
T
A
= 0 to +70˚C, V
CC
=5V±
10%
Symbol Parameter Conditions Min Typ Max Units
DRIVER AND CONTROL INPUT: (Dn, DE*, PS1 and PS2)
V
IH
Minimum Input High Voltage 2.0 V
V
IL
Maximum Input Low Voltage 0.8 V
I
I
Input Leakage Current V
IN
=V
CC
= 5.5V 100 µA
I
IH
Input High Current V
IN
= 2.4V 40 µA
I
IL
Input Low Current V
IN
= 0.5V −100 µA
V
CL
Input Diode Clamp Voltage I
CLAMP
= −12 mA −1.2 V
DRIVER OUTPUT/RECEIVER INPUT: (Bn)
V
OLB
Output Low Bus Voltage Dn = 2.4V, DE*= 0V, 0.75 1.0 1.1 V
(Note 5) I
OL
=80mA
I
OLBZ
Output Low Bus Current Dn = 0.5V, DE*= 2.4V, Bn = 0.75V 100 µA
I
OHBZ
Output High Bus Current Dn = 0.5V, DE*= 2.4V, Bn = 2.1V 100 µA
I
OLB
Output Low Bus Current Dn = 0.5V, DE*= 0V, Bn = 0.75V 220 µA
I
OHB
Output High Bus Current Dn = 0.5V, DE*= 0V, Bn = 2.1V 350 µA
V
TH
Receiver Input Threshold DE*= 2.4V 1.47 1.55 1.62 V
V
CLP
Positive Clamp Voltage V
CC
= Max or 0V, I
Bn
= 1 mA 2.4 3.4 4.5 V
V
CC
= Max or 0V, I
Bn
= 10 mA 2.9 3.9 5.0 V
V
CLN
Negative Clamp Voltage I
CLAMP
= −12 mA −1.2 V
RECEIVER OUTPUT: (FRn and Rn)
V
OH
Voltage Output High Bn = 1.1V, DE*= 2.4V, I
OH
= −2 mA 2.4 3.2 V
V
OL
Voltage Output Low Bn = 2.1V, DE*= 2.4V, I
OL
= 24 mA 0.35 0.5 V
Bn = 2.1V, DE*= 2.4V, I
OL
= 8 mA 0.35 0.4 V
I
OS
Output Short Circuit Current Bn = 1.1V, DE*= 2.4V (Note 4) −40 −70 −100 mA
SUPPLY CURRENT
I
CC
Supply Current: Includes V
CC
,DE
*
= 0.5V, All Dn = 2.4V 50 70 mA
QV
CC
and LI DE*= 2.4V, All Bn = 2.1V 50 70 mA
I
LI
Live Insertion Current DE*= 2.4V, All Dn = 0.5V 1 3 mA
DE*= 0.5V, All Dn = 2.4V 2 5 mA
Note 1: “Absolute Maximum Ratings” are those beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The table of “Electrical Characteristics” provide conditions for actual device operation.
Note 2: All input and/or output pins shall not exceed VCC plus 0.5V and shall not exceed the absolute maximum rating at anytime, including power-up and
power-down. This prevents the ESD structure from being damaged due to excessive currents flowing from the input and/or output pins to QV CC and VCC. There
is a diode between each input and/or output to VCC which is forward biased when incorrect sequencing is applied.Alternatively, a current limiting resistor can be used
when pulling-up the inputs to prevent damage. The current into any input/output pin shall be no greater than 50 mA. Exception, LI and Bn pins do not have power
sequencing requirements with respect to VCC and QVCC. Furthermore, the difference between VCC and QVCC should never be greater than 0.5V at any time
including power-up.
Note 3: All currents into device pins are positive; all currents out of device pins are negative.All voltages are referenced to device ground unless otherwise specified.
All typical values are specified under these conditions.: VCC = 5V and TA= 25˚C unless otherwise stated.
Note 4: Only one output should be shorted at a time, and duration of the short should not exceed one second.
Note 5: Referenced to appropriate signal ground. Do not exceed maximum power dissipation of package.
DS3884A
www.national.com3
AC Electrical Characteristics (Note 6)
T
A
= 0˚C to +70˚C, V
CC
=5V±
10%
Symbol Parameter Conditions Min Typ Max Units
DRIVER
t
PHL
Dn to Bn Prop. Delay DE*=0V 135 ns
t
PLH
(
Figure 1
,
Figure 2
) 135 ns
t
PHL
DE*to Bn Enable Time Dn = 3V 2 4 6 ns
t
PLH
Disable Time (
Figure 1
,
Figure 3
) 246 ns
t
r
Transition Time—Rise/Fall (
Figure 1
,
Figure 2
) 1 2 3.5 ns
t
f
20% to 80% 1 2 3.5 ns
SR Skew Rate is Calculated (Note 11) 0.5 V/ns
from 1.3V to 1.8V
t
skew
Skew between Drivers in (Note 7) 1 3 ns
the Same Package
RECEIVER
t
PHL
Bn to Rn Prop. Delay DE*=3V 245 ns
t
PLH
(
Figure 4
,
Figure 5
) 246 ns
t
skew
Skew between Receivers in (Note 7) 1 3 ns
Same Package
FILTERED RECEIVER
t
PHL
Bn to FRn Prop. Delay PS1 = 0V PS2 = 0V DE*= 3V 6 12 16 ns
(
Figure 4
,
Figure 5
), R
EXT
=13kΩ
PS1=0V PS2=3V DE
*=3V 111621 ns
(
Figure 4
,
Figure 5
), R
EXT
=13kΩ
PS1=3V PS2=0V DE
*=3V 152127 ns
(
Figure 4
,
Figure 5
), R
EXT
=13kΩ
PS1=3V PS2=3V DE
*=3V 253345 ns
(
Figure 4
,
Figure 5
), R
EXT
=13kΩ
t
PLH
Bn to FRn Prop. Delay DE*=3V(
Figure 4
,
Figure 5
)
(Note 8) 257 ns
R
EXT
=13kΩ
t
GR
Glitch Rejection PS1 = 0V PS2 = 0V DE*=3V 5 9 16 ns
(
Figure 4
,
Figure 6
), R
EXT
=13kΩ
PS1=0V PS2=3V DE
*=3V 101318 ns
(
Figure 4
,
Figure 6
), R
EXT
=13kΩ
PS1=3V PS2=0V DE
*=3V 141824 ns
(
Figure 4
,
Figure 6
), R
EXT
=13kΩ
PS1=3V PS2=3V DE
*=3V 243142 ns
(
Figure 4
,
Figure 6
), R
EXT
=13kΩ
FILTERED RECEIVER TIMING REQUIREMENTS
t
s
PSn to Bn Set-Up Time (
Figure 7
), R
EXT
=13kΩ250 ns
PARAMETERS NOT TESTED
Coutput Capacitance at Bn (Note 9) 5 pF
t
NR
Noise Rejection (Note 10) 1 ns
Note 6: Input waveforms shall have a rise/fall time of 3 ns.
Note 7: tskew is an absolute value defined as differences seen in propagation delays between drivers in the same package with identical load conditions.
Note 8: Filtered receiver tPLH is independent of filter setting.
Note 9: The parameter is tested using TDR techniques described in P1194.0 BTL Backplane Design Guide.
Note 10: This parameter is tested during device characterization. The measurements revealed that the part will reject 1 ns pulse width.
Note 11: Futurebus+ transceivers are required to limit bus signal rise and fall times to no faster than 0.5V/ns, measured between 1.3V and 1.8V (approximately 20%
to 80% of nominal voltage swing). The rise and fall times are measured with a transceiver loading equivalent to 12.5Ωtied to +2.1V DC.
DS3884A
www.national.com 4
Pin Descriptions
Pin Name Number of Input/ Description
Pins Output
B1–B6 6 I/O BTL receiver input and driver output
B1GND–B6GND 6 NA Driver output ground reduces bounce due to high
current switching of driver outputs
(Note 12)
DE*1 I Driver Enable Low
D1–D6 6 I TTL Driver Input
FR1–FR3 3 O TTL Filtered Receiver Output
GND 3 NA Ground reference for switching circuits.
(Note 12)
LI 1 NA Power supply for live insertion. Boards that require live
insertion should connect LI to the live insertion pin on
the connector. (Note 13)
NC 4 NA No Connect
PS1, PS2 2 I Pulse Width Selection pin determines glitch filter setting
(Note 14)
R1–R6 6 O TTL Receiver Output
REXT 1 NA External Resistor pin. External resistor is used for
internal biasing of filter circuitry. The 13 kΩresistor shall
be connected between REXT and GND. The resistor
shall have a tolerance of 1% and a temperature
coefficient of 100 ppm/˚C or better.
QGND 2 NA Ground reference for receiver input bandgap reference
and non-switching circuits (Note 12)
QV
CC
1NAV
CC
supply for bandgap reference and non-switching
circuits (Note 13)
V
CC
2NAV
CC
supply for switching circuits (Note 13)
Note 12: the multiplicity of grounds reduces the effective inductance of bonding wires and leads, which then reduces the noise caused by transients on the ground
path. The various ground pins can be tied together provided that the external ground has low inductance (i.e., ground plane with power pins and many signal pins
connected to the backplane ground). If the external ground floats considerably during transients, precautionary steps should be taken to prevent QGND from moving
with reference to the backplane ground. The receiver threshold should have the same ground reference as the signal coming from the backplane. A voltage offset
between their grounds will degrade the noise margin.
Note 13: The same considerations for ground are used for V CC in reducing lead inductance (see Note 12). QVCC and V CC should be tied together externally. If
live insertion is not supported, the LI pin can be tied together with QVCC and VCC.
Note 14: See AC characteristics for filter setting.
DS3884A
www.national.com5
Pin Descriptions (Continued)
DE*Dn FRn Rn Bn
HXHHL
HXLLH
LHHHL
LLLLH
X: High or low logic state
L: Low state
H: High state
L-H: Low to high transition
Glitch Filter Table
PS1 PS2 Filter Setting
LL 5ns
L H 10 ns
H L 14 ns
H H 24 ns
Application Information
The DS3884A is pin to pin and functionally compatible with
the DS3884. The DS3884A is a speed and power enhanced
version of the DS3884. There are two minor differences
between the DS3884 and DS3884A.
The external resistor used in the DS3884A is different from
that used in the DS3884. REXT for the DS3884 is 6.2k while
REXT for the DS3884Ais 13k. The available filter settings for
the DS3884Aare 5 ns, 10 ns, 14 ns, 24 ns, while the settings
for the DS3884 are 5 ns, 7.5 ns, 15 ns, and 25 ns.
Utilization of the DS3884A simplifies the implementation of
all handshake signals which require Wired-OR glitch filtering.
Three of the six bits have an additional parallel Wired-OR
filtered receive output giving a total of nine receiver outputs.
DS011460-5
FIGURE 1. Driver Propagation Delay Set-Up
DS011460-6
FIGURE 2. Driver: Dn to Bn
DS011460-7
FIGURE 3. Driver: DE*to Bn
DS011460-8
Switch Position
t
PLH
t
PHL
S1 open close
FIGURE 4. Receiver Propagation Delay Set-Up
DS011460-9
FIGURE 5. Receiver: Bn to FRn, Bn to Rn
DS011460-10
FIGURE 6. Receiver: t
GR
, FRn(min) = 2V
DS011460-11
FIGURE 7. Receiver: PSn to Bn
DS3884A
www.national.com 6
Application Information (Continued)
In Wired-OR applications, the glitch generated as drivers are
released from the bus, is dependent upon the backplane and
parasitic wiring components causing the characteristics of
the glitch to vary in pulse width and amplitude. To accom-
modate this variation the DS3884Afeatures two pins defined
as PS1 and PS2 which allow selection of a 5 ns, 10 ns, 14 ns
and 24 ns filter setting to optimize glitch filtering for a given
situation. The REXT pin is issued in conjunction with the
filtering circuitry and requires a 13 kΩresistor to ground. For
additional information on Wired-OR glitch, reference Appli-
cation Note AN-774.
The DS3884A driver output configuration is an NPN open
collector which allows Wired-OR connection on the bus.
Each driver output incorporates a Schottky diode in series
with its collector to isolate the transistor output capacitance
from the bus thus reducing the bus loading in the inactive
state. The combined output capacitance of the driver and
receiver input is typically less than 5 pF. The driver also has
high sink current capability to comply with the bus loading
requirements defined within IEEE 1194.1 BTL specification.
Backplane Transceiver Logic (BTL) is a signaling standard
that was invented and first introduced by National Semicon-
ductor, then developed by the IEEE to enhance the perfor-
mance of backplane buses. BTL compatible transceivers
feature low output capacitance drivers to minimize bus load-
ing, a 1V nominal signal swing for reduced power consump-
tion and receivers with precision thresholds for maximum
noise immunity. The BTL standard eliminates settling time
delays that severely limit TTL bus performance, and thus
provide significantly higher bus transfer rates. The back-
plane bus is intended to be operated with termination resis-
tors (selected to match the bus impedance) connected to
2.1V at both ends. The low voltage is typically 1V.
Separate ground pins are provided for each BTL output to
minimize induced ground noise during simultaneous switch-
ing.
The device’s unique driver circuitry meets a maximum slew
rate of 0.5V/ns which allows controlled rise and fall times to
reduce noise coupling to adjacent lines.
The transceiver’s high impedance control and driver inputs
are fully TTL compatible.
The receiver is a high speed comparator that utilizes a
bandgap reference for precision threshold control allowing
maximum noise immunity to the BTL 1V signaling level.
Separate QV
CC
and QGND pins are provided to minimize
the effects of high current switching noise. Output pins
FR1–FR3 are the filtered outputs and R1–R6 are the unfil-
tered outputs. All receiver outputs are fully TTL compatible.
The DS3884A supports live insertion as defined for Future-
bus+ through the LI (Live Insertion) pin. To implement live
insertion the LI pin should be connected to the live insertion
power connector. If this function is not supported the LI pin
must be tied to the V
CC
pin. The DS3884A also provides
power up/down glitch free protection during power sequenc-
ing.
The DS3884A has two types of power connections in addi-
tion to the LI pin. They are the Logic V
CC
(V
CC
) and the Quiet
V
CC
(QV
CC
). There are two V
CC
pins on the DS3884A that
provide the supply voltage for the logic and control circuitry.
Multiple connections are provided to reduce the effects of
package inductance and thereby minimize switching noise.
As these pins are common to the V
CC
bus internal to the
device, a voltage difference should never exist between
these pins and the voltage difference between V
CC
and QV
CC
should never exceed ±0.5V because of ESD circuitry.
Additionally, the ESD circuitry between the V
CC
pins and all
other pins except for BTL I/O’s and LI pins requires that any
voltage on these pins should not exceed the voltage on V
CC
+ 0.5V.
There are three different types of ground pins on the
DS3884A. They are the logic ground (GND), BTL grounds
(B1GND–B6GND) and the Bandgap reference ground
(QGND). All of these ground reference pins are isolated
within the chip to minimize the effects of high current switch-
ing transients. For optimum performance the QGND should
be returned to the connector through a quiet channel that
does not carry transient switching current. The GND and
B1GND–B6GND should be connected to the nearest back-
plane ground pin with the shortest possible path.
Since many different grounding schemes could be imple-
mented and ESD circuitry exist on the DS3884A, it is impor-
tant to note that any voltage difference between ground pins,
QGND, GND or B1GND–B6GND should not exceed ±5V
including power up/down sequencing.
Additional transceivers included in the Futurebus+ / BTL
family are; the DS3883A BTL 9-bit Transceiver, and the
DS3886A BTL 9-bit Latching Data Transceiver featuring
edge triggered latches in the driver which may be bypassed
during a fall-through mode and a transparent latch in the
receiver.
DS3884A
www.national.com7
Physical Dimensions inches (millimeters) unless otherwise noted
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
44-Pin PQFP
Order Number DS3884AVF
NS Package VF44B
DS3884A BTL Handshake Transceiver
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
