ISL9214A (R) Data Sheet May 5, 2008 FN6698.0 Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources Features The ISL9214A is a fully integrated low-cost single-cell Li-ion or Li-polymer battery charger. The charger accepts two power inputs, normally one from a USB (Universal Serial Bus) port and the other from a desktop cradle. The ISL9214A is an ideal charger for smart handheld devices that need to communicate with a personal computer via USB. * Dual Input Power Sources for Cradle and USB The ISL9214A features 28V maximum voltages for both the cradle and the USB inputs. Due to the 28V rated inputs, low-cost, large output tolerance adapters can be used safely. When both inputs are powered, the cradle input is used to charge the battery. The charge current is programmable for the cradle input with a small resistor. The end-of-charge current is also programmable by another external resistor. The charger incorporates ThermaguardTM which protects the IC against over-temperature. If the die temperature rises above a typical value of +125C, a thermal foldback function reduces the charge current automatically to prevent further temperature rise. The charger has two indication pins. The PPR (power present) pin outputs an open-drain logic LOW when either the cradle or the USB input power is attached. The CHG (charge) pin is also an open-drain output that indicates a logic LOW when the charge current is above a minimum current level. When the charge current is below the preset minimum current, the CHG pin will indicate a logic HIGH signal. This status is latched and will be reset under one of the following events: * Charge Current ThermaguardTM for Thermal Protection * Complete Charger for Single-Cell Li-ion/Polymer Batteries 1. The part is disabled and re-enabled 2. The selected input source has been removed and reapplied 3. The USBON turns LOW 4. The BAT pin voltage falls below the recharge threshold (~3.9V). ISL9214AIRZ* PART TEMP. MARKING RANGE (C) 214A -40 to +85 PACKAGE (Pb-Free) * Fixed 380mA USB Charge Current * Programmable Cradle Charge Current * 28V Maximum Voltages for Cradle and USB Inputs * Adapter Presence and Charge Indications * Less than 0.5A Leakage Current Off the Battery When No Input Power Attached * Programmable End-of-Charge Current * Ambient Temperature Range: -40C to +85C * No External Blocking Diode Required Applications * Smart Handheld Devices * Cell Phones, PDAs, MP3 Players * Digital Still Cameras * Handheld Test Equipment Related Literature * Technical Brief TB363 "Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)" * Technical Brief TB389 "PCB Land Pattern Design and Surface Mount Guidelines for QFN Packages" ISL9214A (10 LD DFN) TOP VIEW PKG. DWG. # 10 Ld 3x3 DFN L10.3x3C *Add "-T" suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 * Integrated Pass Elements Pinout Ordering Information PART NUMBER (Note) * Low Component Count CRDL 1 10 BAT USB 2 9 ICDL PPR 3 8 GND CHG 4 7 USBON EN 5 6 IMIN CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved. Thermaguard is a trademark of Intersil Americas Inc. All other trademarks mentioned are the property of their respective owners. ISL9214A Block Diagram CRDL BAT USB TEMP MONITOR CA + CPPR + VA ICDL VREF REFERENCE CURRENT IR CONTROL IMIN ENA USB CPPR CRDL BAT LBAT EN PPR CONTROL GND CHG USBON 2 FN6698.0 May 5, 2008 ISL9214A Typical Applications A Simple Charger Accepting Power from Both a USB Port and a Desktop Cradle TO CRADLE CONNECTOR TO BATTERY BAT CRDL C1 RICDL ICDL R1 C3 ISL9214A TO USB CONNECTOR ON OFF USBON USB PPR C2 R3 R4 D1 D2 CHG R2 EN DISABLE ENABLE GND IMIN RIMIN TABLE 1. COMPONENT SELECTION RICDL 12.4k for 0.55A cradle charge current RIMIN 10k for 55mA end-of-charge current R3, R4 350 C1, C2, C3 1F ceramic capacitor R1, R2 1 D1, D2 LEDs A Simple Charger with Programmable Charge Current and Wide Input Voltage Range TO CRADLE CONNECTOR TO BATTERY BAT CRDL C1 RICDL ICDL R1 ISL9214A C3 R3 R4 D1 D2 USBON PPR USB CHG EN RIMIN GND IMIN DISABLE ENABLE TABLE 2. COMPONENT SELECTION RICDL 12.4k for 0.55A cradle charge current RIMIN 10k for 55mA end-of-charge current R3, R4 350 C1, C3 1F ceramic capacitor R1 D1, D2 3 1 LEDs FN6698.0 May 5, 2008 ISL9214A Absolute Maximum Ratings Thermal Information Supply Voltage (CRDL, USB) . . . . . . . . . . . . . . . . . . . . -0.3V to 28V Other Input Voltage (EN, USBON, ICDL, IMIN, BAT) . . . -0.3V to 7V Open-Drain Pull-Up Voltage (PPR, CHG) . . . . . . . . . . . . -0.3V to 7V Thermal Resistance JA (C/W) JC (C/W) DFN Package (Notes 1, 2) . . . . . . . . . . 40 2.5 Maximum Junction Temperature (Plastic Package) . . . . . . . +150C Maximum Storage Temperature Range . . . . . . . . . .-65C to +150C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Temperature Range . . . . . . . . . . . . . . . . . . .-40C to +85C Supply Voltage (USB Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 5.5V Supply Voltage (CRDL Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 24V Typical Cradle Charge Current . . . . . . . . . . . . . . . . . . 100mA to 1A Typical USB Charge Current . . . . . . . . . . . . . . . . . . . . . . . . . 380mA CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. 2. For theta JC the "case temp." location is the center of the exposed metal pad on the package underside. Electrical Specifications Typical values are tested at USB = CRDL = 5V and +25C Ambient Temperature, maximum and minimum values are established over the recommended operating conditions, unless otherwise noted. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Rising USB/CRDL Threshold 3.4 3.9 4.2 V Falling USB/CRDL Threshold 3.15 3.3 3.45 V - 150 250 mV 20 80 - mV - 0.05 0.5 A - 150 220 A - 150 220 A - 0.55 0.8 mA POWER-ON RESET VIN-BAT OFFSET VOLTAGE Rising Edge VOS Falling Edge VOS VBAT = 4.0V, use CHG pin to indicate the comparator output (Note 3) STANDBY CURRENT BAT Pin Sink Current ISTANDBY EN = HIGH or both inputs are floating CRDL Pin Supply Current ICRDL USB Pin Supply Current EN = HIGH IUSB CRDL/USB Pin Supply Current EN = LOW or floating VOLTAGE REGULATION Output Voltage VCH Load = 10mA 4.158 4.2 4.242 V Output Voltage VCH Load = 10mA (Tj = +25C) 4.174 4.2 4.226 V CRDL PMOS ON-Resistance VBAT = 3.8V, ICHARGER = 0.3A, (Tj = +25C) 200 600 850 m USB PMOS ON-Resistance VBAT = 3.8V, ICHARGER = 0.3A, (Tj = +25C) 200 600 850 m VBAT = 3.8V 1.19 1.22 1.25 V CHARGE CURRENT (Note 4) ICDL Pin Output Voltage VICDL CRDL Input Constant Charge Current ICHARGE RICDL = 12.4k, VBAT: 2.7V to 3.8V 520 550 580 mA CRDL Input Trickle Charge Current ITRICKLE 16 18 20 % 46.5 55 63.5 mA 332 380 410 mA 66 80 91 mA 2.5 2.6 2.7 V CRDL and USB End-of-Charge Threshold IMIN RICDL = 12.4k, VBAT = 2.2V Given as a % of the CRDL ICHARGE RIMIN = 10.0k USB Input Constant Charge Current ICHARGE USBON = HIGH, VBAT: 2.7V to 3.8V USB Input Trickle Charge Current ITRICKLE VBAT = 2.2V PRECONDITIONING CHARGE THRESHOLD Preconditioning Charge Threshold Voltage 4 VMIN FN6698.0 May 5, 2008 ISL9214A Electrical Specifications Typical values are tested at USB = CRDL = 5V and +25C Ambient Temperature, maximum and minimum values are established over the recommended operating conditions, unless otherwise noted. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS VRCH 3.8 3.9 4.0 V TFOLD 110 125 140 C USBON Logic Input High 1.3 - - V USBON Logic Input LOW - - 0.4 V EN Pin Logic Input High 1.3 - - V EN Pin Logic Input Low - - 0.4 V EN Pin Internal Pull-Down Resistance 350 600 850 k USBON Pin internal Pull-Down Resistance 700 1000 1300 k 10 - - mA RECHARGE THRESHOLD Recharge Threshold Voltage INTERNAL TEMPERATURE MONITORING Current Foldback Threshold (Note 5) LOGIC INPUT AND OUTPUT CHG/PPR Sink Current Pin Voltage = 0.8V NOTES: 3. The 4.0V VBAT is selected so that the CHG output can be used as the indication for the offset comparator output indication. If the VBAT is lower than the POR threshold, no output pin can be used for indication. 4. The charge current can be affected by the thermal foldback function if the IC under the test setup cannot dissipate the heat. 5. Limits established by characterization and are not production tested. Typical Operating Performance The test conditions for the Typical Operating Performance are: VIN = 5V, TA = +25C, RICDL = 12.4k, RIMIN = 10.0k, VBAT = 3.7V, Unless Otherwise Noted. 4.2100 CHARGE CURRENT = 1mA 4.20 4.2075 CRDL 4.2050 VBAT (V) VBAT (V) 4.18 4.16 USB 4.14 CHARGE CURRENT = 1mA 4.2025 CRDL 4.2000 USB 4.1975 4.1950 4.12 4.1925 4.10 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 140 FIGURE 1. CHARGER OUTPUT VOLTAGE vs TEMPERATURE 5 4.1900 0 5 10 15 20 25 VIN (V) FIGURE 2. CHARGER OUTPUT VOLTAGE vs INPUT VOLTAGE FN6698.0 May 5, 2008 ISL9214A Typical Operating Performance The test conditions for the Typical Operating Performance are: VIN = 5V, TA = +25C, RICDL = 12.4k, RIMIN = 10.0k, VBAT = 3.7V, Unless Otherwise Noted. (Continued) 600 600 550 CRDL, RICDL = 12.4k CHARGE CURRENT (mA) CHARGE CURRENT (mA) 550 500 450 400 USB 350 300 250 450 400 350 2.8 3.0 3.3 VBAT (V) 3.5 3.8 300 200 -40 4.0 FIGURE 3. CHARGE CURRENT vs OUTPUT VOLTAGE 1.8 1.8 1.6 1.6 LEAKAGE CURRENT (A) 2.0 1.4 1.2 CRDL 1.0 0.8 0.6 USB -20 0 20 40 60 TEMPERATURE (C) 80 120 140 VBAT = 4.2V 1.2 1.0 0.8 0.6 0.4 -20 0 20 40 60 80 100 120 140 TEMPERATURE (C) FIGURE 6. REVERSE CURRENT vs TEMPERATURE 700 700 IOUT = 0mA IOUT = 0mA 600 500 QUIESCENT CURRENT 600 QUIESCENT CURRENT 20 40 60 80 100 TEMPERATURE (C) 1.4 0 -40 100 FIGURE 5. rDS(ON) vs TEMPERATURE AT 3.7V OUTPUT CRDL 400 300 USB 200 500 CRDL 400 300 200 USB 100 100 0 -40 0 0.2 0.2 0 -40 -20 FIGURE 4. CHARGE CURRENT vs AMBIENT TEMPERATURE 2.0 0.4 USB 250 200 2.5 rDS(ON) () CRDL, RICDL = 12.4k 500 -20 0 20 40 60 80 100 120 TEMPERATURE (C) FIGURE 7. CRADLE INPUT QUIESCENT CURRENT vs TEMPERATURE 6 140 0 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (C) FIGURE 8. USB INPUT QUIESCENT CURRENT vs TEMPERATURE FN6698.0 May 5, 2008 ISL9214A Typical Operating Performance The test conditions for the Typical Operating Performance are: VIN = 5V, TA = +25C, RICDL = 12.4k, RIMIN = 10.0k, VBAT = 3.7V, Unless Otherwise Noted. (Continued) 800 800 IOUT = 0mA IOUT = 0mA 700 QUIESCENT CURRENT QUIESCENT CURRENT 700 600 ENABLED 500 IOUT = 0mA 400 300 200 DISABLED 600 ENABLED 500 IOUT = 0mA 400 300 200 DISABLED 100 100 0 0 0 5 10 15 20 25 0 FIGURE 9. CRADLE INPUT QUIESCENT CURRENT vs INPUT VOLTAGE 5 10 15 20 25 TEMPERATURE (C) TEMPERATURE (C) FIGURE 10. USB INPUT QUIESCENT CURRENT vs INPUT VOLTAGE Functional Pin Description IMIN (Pin 6) CRDL (Pin 1) IMIN is the programmable input for the end-of-charge current. IMIN is calculated by using Equation 1: Cradle input. This pin is usually connected to a cradle power input. The maximum input voltage is 28V. The charge current from this pin is programmable with the ICDL pin up to 1A. When this pin is connected to a power source, no charge current is drawn from the USB pin. A 1F or larger value ceramic capacitor is recommended for decoupling. Where RIMIN is in k. IMIN is applicable for both cradle and USB charging. USB (Pin 2) USBON (Pin 7) USB input. This pin is usually connected to a USB port power connector and other sources that are also acceptable. The charge current from the USB pin is fixed at typically 380mA. A 1F or larger value ceramic capacitor is recommended for decoupling. It is also recommended to have a 1 resistor in series with the decoupling capacitor to prevent an over-shoot voltage when a USB cable is plugged in. The USBON pin is a control input to turn off the USB charge function if desired. Connect to LOW or leave floating to turn off USB charge. PPR (Pin 3) Power presence indication. An open-drain output pin, which turns ON when either the USB input voltage or the CRDL input voltage is above its POR level, regardless of the charger is enabled or disabled, otherwise it turns OFF. This pin provides a wake-up signal to a microprocessor when either the cradle or the USB power is connected. CHG (Pin 4) Charge indication pin. An open-drain output, which turns ON when the charge current is above programmable threshold, otherwise it turns OFF. 550 I MIN = ---------------R IMIN ( mA ) (EQ. 1) GND (Pin 8) System ground. ICDL (Pin 9) The ICDL pin has two functions. The first function is to program the cradle charge current during the constant-current mode. The voltage of this pin is 1.22V during the constant-current mode of the cradle charger. The constant-current mode current is programmed by using Equation 2: 6820 I CDL = ----------------R ICDL ( mA ) (EQ. 2) where RICDL is the resistor in k, connected to the ICDL pin (see "Typical Applications" on page 3). It is recommended that the charge current be programmed in the range of 100mA to 1000mA. EN (Pin 5) Enable logic input. Connect to LOW or leave floating to enable the charger. 7 The second function of the ICDL pin is to monitor the actual charge current. The voltage of this pin, VICDL, is proportional to the actual charge current, ICHG. FN6698.0 May 5, 2008 ISL9214A The cradle charge current should be programmed equal or higher than the USB current; otherwise, the ICDL pin voltage will be higher than 1.22V during the constant-current mode when the USB charger is working. The charger still works properly but the accuracy of the current monitoring voltage degrades and saturates at approximately 2.1V. BAT (Pin 10) Charger output pin. Connect this pin to the battery pack or the battery cell. A 1F or larger value ceramic capacitor is recommended for decoupling. The charger relies on the battery for stability so a battery should always be connected to the BAT pin. Description The ISL9214A is designed for a single-cell Li-ion or Li-polymer battery charging circuit that accepts both a USB port and a desktop cradle as its power source. While the charge-current from the USB input source is fixed at 380mA, the charge current from the cradle input is programmable between 0.1A and 1.0A by the resistor RICDL. Similarly, the end-of-charge current is programmable by connecting a resistor at the IMIN pin. The end-of-charge threshold can be calculated with the Equation 1 given in the "Functional Pin Description" on page 7. The same threshold applies to both the cradle and the USB inputs. Input Auto Selection When both input sources are present, the charger selects only one power source to charge the battery. When the CRDL input is higher than the POR threshold, CRDL is selected as the power source, otherwise, the USB input is selected. If the CRDL input voltage is below the battery voltage but the USB input voltage is higher than the battery voltage, then the USB input is used to charge the battery. The control circuit always breaks both internal power devices before switching from one power source to the other to avoid a cross conduction of both power MOSFETs. The USBON pin is equivalent to a logic LOW when left floating. Typically, the P-Channel MOSFET for the USB input has an rDS(ON) of 600m at room temperature. With a 380mA charge current, the typical head room is 228mV. Thus, if the input voltage drops to a level that the voltage difference between the USB pin and the BAT pin is less than 228mV, the rDS(ON) becomes a limiting factor of the charge-current; and the charger drops out the constant-current regulation. Cradle Charge Current The cradle charge current is enabled by the EN pin only; the USBON pin has no control on the cradle charge current. The cradle charge current is programmed with the external resistor connected between the ICDL pin and the GND pin. The current can be calculated with Equation 2 given in the ICDL pin description on page 7. The typical rDS(ON) of the P-Channel MOSFET for the CRDL input is 600m at room temperature. When the head room between the input and output voltages is small, the actual charge current, similar to the USB case, could be limited by the rDS(ON). On the other hand, if the headroom between the input and output voltages is large, the charge current may be limited by the thermal foldback threshold. Floating Charge Voltage The floating voltage during the constant voltage phase is 4.2V. The floating voltage has an 1% accuracy over the ambient temperature range of -40C to +85C. Trickle Charge Current When the battery voltage is below the minimum battery voltage VMIN given in the "Electrical Specification" table on page 4, the charger operates in a trickle/preconditioning mode, where the charge current is typically 18% of the programmed charge current for the cradle input. If power comes from the USB input, the trickle current is approximately 80mA. End-Of-Charge Indication USB Charge Current When the USB port is selected as the power source, the charge-current is enabled by the logic input at the USBON pin. When the USBON is driven to logic LOW, the charger is disabled. When the USBON is driven to logic HIGH, the charge current is fixed at a typical value of 380mA. Thus, for the USB input, the USBON pin has a similar function as the EN pin. Table 3 describes the USB charge control by both the USBON pin and EN pin: 1. The part is disabled and re-enabled 2. The selected input source has been removed and reapplied TABLE 3. USB CHARGE CONTROL EN = LOW EN = HIGH USBON = LOW Disabled Disabled USBON = HIGH Enabled Disabled 8 When an EOC condition (charge current falls below IMIN during constant voltage charge) is encountered, the CHG pin internal open-drain MOSFET turns off. The IMIN threshold is programmable by the resistor at the IMIN pin for both cradle and USB inputs. Once the EOC condition is reached, the status is latched and can be reset at one of the following conditions: 3. The USBON turns LOW and turns back to HIGH for the USB input 4. The BAT pin voltage falls below the recharge threshold (~3.9V) FN6698.0 May 5, 2008 ISL9214A TRICKLE CC not charge the battery if the input voltage does not meet the power-good conditions. CV 4.2V IREF CHARGE VOLTAGE 3.9V The thermal foldback function reduces the charge current when the internal temperature reaches the thermal foldback threshold, which is typically +125C. This protects the charger from excessive thermal stress at high input voltages. CHARGE CURRENT 2.6V 18 100 IREF IMIN Input Bypass Capacitors CHG INDICATION TIME FIGURE 11. TYPICAL CHARGE CYCLE Figure 11 shows the typical charge profile including the end-of-charge event. Power Presence Indication When either the USB or the cradle input voltage is above the POR threshold, the PPR pin internal open-drain MOSFET turns on indicating the presence of input power. Power-Good Conditions Even if there is power present, the charger will not deliver any current to the output if the power-good conditions are not met. The following two conditions together define the power-good voltage range: 1. VCDRL or VUSB > VPOR 2. VCDRL or VUSB - VBAT > VOS where VPOR is the power-on reset threshold and VOS is the offset voltage for the input and output voltage comparator. All of these thresholds have hysteresis, as given in the "Electrical Specification" table on page 4. The charger will 9 Thermal Foldback (ThermaguardTM) Due to the inductance of the power leads of the wall adapter or USB source, the input capacitor type must be properly selected to prevent high voltage transient during a hot-plug event. A tantalum capacitor is a good choice for its high ESR, which provides damping to the voltage transient. Multilayer ceramic capacitors, however, have a very low ESR, and hence, when chosen as input capacitors, a 1 series resistor must be used (as shown in the "Typical Applications" on page 3) in order to provide adequate damping. State Diagram The state diagram for the charger functions is shown in Figure 12. The diagram starts with the Power-Off state. When at least one input voltage rises above the POR threshold, the charge resets it self. If both input voltages are above the POR threshold, the charger selects the CRDL input as the power source. Then, if the EN pin is at a logic HIGH voltage, the charger stays in disabled state. If the EN pin goes LOW, the fast charge starts. Any time the EN pin turns HIGH, the charger returns to the disabled state. When the EOC condition is reached, the CHG will turn to logic HIGH to indicate a charge complete status but the charge will continue. The EOC condition is then latched until one of the four re-charge conditions is encountered, as shown in Figure 11. FN6698.0 May 5, 2008 ISL9214A VCRDL < VPOR VUSB < VPOR PWR OFF CHARGER: OFF PPR: OFF CHG: OFF POR USB INPUT SELECTED CHARGER: OFF PPR: ON CHG: OFF VCRDL > VPOR VUSB > VPOR EN = HI VCRDL > VPOR VUSB < VPOR EN = HI VCRDL < VPOR VUSB > VPOR EN = HI POR CRDL INPUT SELECTED CHARGER: OFF PPR: ON CHG: OFF POR CRDL INPUT SELECTED CHARGER: OFF PPR: ON CHG: OFF SOURCE SELECTED CHARGER DISABLED CHARGER: OFF PPR: ON CHG: OFF ANYTIME EN PIN CHANGES TO DISABLE NOT ENABLED ENABLED, VBAT<VMIN ENABLED, VBAT>VMIN TRICKLE CHARGE CHARGER: ON PPR: ON CHG: ON VBAT>VMIN FAST CHARGE CHARGER: ON PPR: ON CHG: ON VBAT > VRCH AND ICHG < IMIN RECHARGE CONDITION IS MET AND VBAT> VMIN RECHARGE CONDITION IS MET AND VBAT< VMIN CHARGE COMPLETE CHARGER: ON PPR: ON CHG: OFF FIGURE 12. STATE DIAGRAM 10 FN6698.0 May 5, 2008 ISL9214A Dual Flat No-Lead Plastic Package (DFN) L10.3x3C 2X 0.10 C A A 10 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE D MILLIMETERS 2X 0.10 C B E SYMBOL MIN NOMINAL MAX NOTES A 0.85 0.90 0.95 - A1 - - 0.05 - A3 6 INDEX AREA b 0.20 REF 0.20 D TOP VIEW B D2 // A C SEATING PLANE D2 6 INDEX AREA 0.08 C 7 8 D2/2 1 2.33 2.38 2.43 7, 8 1.69 7, 8 3.00 BSC 1.59 e 1.64 - 0.50 BSC - k 0.20 - - - L 0.35 0.40 0.45 8 N 10 2 Nd 5 3 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. NX k 2. N is the number of terminals. 3. Nd refers to the number of terminals on D. E2 E2/2 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. NX L N N-1 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX b e (Nd-1)Xe REF. BOTTOM VIEW 5 0.10 M C A B (A1) 9 L 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. CL NX (b) 5, 8 Rev. 1 4/06 2 (DATUM A) 8 0.30 3.00 BSC E E2 A3 SIDE VIEW (DATUM B) 0.10 C 0.25 - 9. COMPLIANT TO JEDEC MO-229-WEED-3 except for dimensions E2 & D2. e SECTION "C-C" C C TERMINAL TIP FOR ODD TERMINAL/SIDE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 FN6698.0 May 5, 2008