Flameproof Power Metal Film Resistors Welwyn Components MFP Series * * * Smallest size for power rating Resistance range 0.1 ohms to 1M ohms Flameproof protection Electrical Data MFP1 Power rating at 70C watts Resistance range ohms Limiting element voltage <1 : 0.7 MFP2 >=1 : 1.0 2 0R1 - 1M 1R0 - 1M volts TCR ppm/C Resistance tolerance 350 < 1 : 300 1 - 9.1 : 200 10 : 50 % 100 1, 2, 5 Standard values E24 preferred Thermal impedance C/watt Ambient temperature range 120 82 C -55 to 155 Physical Data Dimensions (mm) & Weight (g) PCB Min. bend radius Wt.nom L Max D Max f min d nom mounting centres MFP1 6.2 2.5 21.0 0.6 10.2 0.6 0.3 MFP2 10.0 4.0 27.0 0.8 18.4 1.2 0.55 Type d D L f Construction Marking The resistance element is a precisely controlled thin film of metal alloy on a high purity ceramic core, protected by a cement coating applied so that terminations remain completely clear. This permits a well defined body length (clean lead to clean lead dimension L). Resistors are colour coded with 4 or 5 bands depending on value and tolerance. IEC 62 colours are used. Solvent Resistance The body protection and marking are resistant to all normal industrial cleaning solvents suitable for printed circuits. Terminations Material Solder-coated copper wire. Flammability Strength The terminations meet the requirements of IEC 68.2.21 The resistor coating will not burn or emit incandescent particles under any condition of applied temperature or power overload. Solderability The terminations meet the requirements of IEC 115-1, Clause 4.17.3.2 General Note Welwyn Components reserves the right to make changes in product specification without notice or liability. All information is subject to Welwyn's own data and is considered accurate at time of going to print. A subsidiary of TT electronics plc (c) Welwyn Components Limited * Bedlington, Northumberland NE22 7AA, UK Telephone: +44 (0) 1670 822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com Issue D * 03.06 143 Flameproof Power Metal Film Resistors Welwyn Components MFP Series Performance Data Maximum Load at rated power : 1000 hours at 70C R % 5 Shelf life : 12 months at room temperature R % 2 Derating from rated power at 70C R % zero at 155C Climatic R % 3 Climatic category 50/155/56 Temperature rapid change R % 0.5 Resistance to solder heat R % 0.5 volts 500 min Voltage proof Application Notes Packaging 1. If the resistors are to dissipate full rated power, it is recommended that the terminations should not be soldered closer than 4mm from the body. 2. Due to operating temperature limitations imposed by some pcb materials, derating may be necessary. An estimate of the temperature rise to be expected can be calculated using the thermal impedance figures given under Electrical Data. 3. MFP resistors an also be supplied pre-formed. MFP resistors are normally supplied tape packed ready for loading onto automatic sequencing and insertion machines. The standard taping method and critical dimensions are shown in Figure 1. Component wires will not protrude beyond the outside edge of the tapes. Alternative packaging available by request. Lead Formed resistors can also be supplied. Standard options of Lancet, Radial and Goalpost forming are shown in lead Form Information section. Figure 1 Type MFP1 MFP2 52 68 b (mm) 5 f1 6 f2 b 6 Body location f1 - f2 1.4 mm Ordering Procedure Example: MFP2 at 4.7 kilohms and 1% tolerance in ammo pack box of 2000 pieces - MFP2- 4K7FI Type Value (use IEC62 code) Tolerance (use IEC62 code) F G J 1% 2% 5% Packing I Ammo MFP1 MFP2 5000/box 2000/box Standard (c) Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK Telephone: +44 (0) 1670 822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com 144 Issue D * 03.06