ST www.vishay.com Vishay SuperTan(R) Wet Tantalum Capacitors with Hermetic Seal FEATURES * * * * * * * * * Vishay ST represents a major breakthrough in wet tantalum capacitor technology. Its unique cathode system provides the highest capacitance per unit volume. The design facilitates a doubling of capacitance, lower ESR and higher ripple current rating compared with conventional wet tantalum products. Moreover, the ST has the capacitance stability of a solid tantalum capacitor and there are no circuit impedance restrictions. The ST is housed in an all tantalum, hermetically sealed case and is manufactured to withstand hazardous environments. The ST is used widely in the defense and aerospace industries and whenever there is a space problem. PERFORMANCE CHARACTERISTICS Operating Temperature: -55 C to +85 C (to +125 C with voltage derating) Capacitance Tolerance: at 120 Hz, +25 C. 20 % standard. 10 % available as special. Very high capacitance 10 F to 1800 F Available 25 VDC to 125 VDC Very low ESR Available High ripple current All tantalum case Hermetically sealed Low DCL Axial through-hole terminations: standard tin / lead (Sn / Pb), 100 % tin (RoHS-compliant) available * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details APPLICATION NOTES a. No continuous reverse voltage permissible. b. The peak of the applied AC ripple and the applied DC voltage must not exceed the DC voltage rating of the capacitor. c. Ripple current ratings by part number at 85 C and 40 kHz are included in the table. Ripple current correction factors for other temperatures and frequencies are given on the next page. d. Transient reverse voltage surges are acceptable under the following conditions: the peak reverse voltage does not exceed 1.5 V and the peak current times the duration of the reverse transient does not exceed 0.05 As. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. DIMENSIONS in inches [millimeters] Terminal welded to case 0.250 [6.35] MAX. 0.0253 0.002 [0.64 0.05] dia. (no. 22 AWG) tinned nickel leads solderable and weldable 0.094 [2.38] MAX. L1 E E "D" DIA. Terminal location within 0.031 of center CASE CODE D 0.016 [0.41] MAX. INSULATED (DIA.) L1 + 0.031 / - 0.016 [+ 0.79 / - 0.41] UNINSULATED E 0.250 [6.3] MAX. T1 0.188 [4.78] 0.219 [5.56] 0.453 [11.51] 1.500 [38.10] T2 0.281 [7.14] 0.312 [7.92] 0.641 [16.28] 2.250 [57.15] L2 0.281 [7.14] 0.312 [7.92] 1.008 [25.60] 2.250 [57.15] T3 0.375 [9.52] 0.406 [10.31] 0.766 [19.46] 2.250 [57.15] T4 0.375 [9.52] 0.406 [10.31] 1.062 [26.97] 2.250 [57.15] Notes * Material at egress is Tantalum * Insulation sleeving will lap over the ends of the capacitor case Revision: 25-Jun-2018 * Approx. weight: T1: 2.3 g, T2: 5.7 g, T3: 9.4 g, T4: 14.8 g Document Number: 43000 1 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay ORDERING INFORMATION ST 220 100 T4 M I E3 Super Tan(R) COMMERCIAL CAP. TYPE CAPACITANCE F 85 C RATED DC VOLTAGE CASE CODE CAPACITANCE TOLERANCE INSULATING SLEEVE RoHS-compliant M = 20 % K = 10 % I = insulated X = uninsulated E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination (standard design) STANDARD RATINGS MAX. DCL AT MAX. IMP. AT -55 C AND 120 Hz () MAX. CAPACITANCE CHANGE AT +125 C (%) AC RIPPLE 85 C 40 kHz (mA) RMS PART NUMBER +8 +12 1250 ST120-25T1MI +10 +15 2100 ST560-25T2MI +45 3200 ST1100-25L2MI CAPACITANCE AT 25 C AND 120 Hz (F) CASE CODE MAX. ESR 120 Hz () +25 C (A) +85 C / +125 C (A) 120 T1 1.3 1 5 25 -42 560 T2 0.83 2 10 12 -65 1100 L2 0.5 3 25 7 -60 +20 1200 T3 0.65 5 20 7 -70 +12 +18 2600 ST1200-25T3MI 1800 T4 0.5 6 25 7 -72 +12 +20 3100 ST1800-25T4MI -55 C (%) +85 C (%) 25 VDC AT 85 C; 15 VDC AT 125 C 30 VDC AT 85 C; 20 VDC AT 125 C 100 T1 1.3 1 5 25 -38 +8 +12 1200 ST100-30TMI 470 T2 0.85 2 10 15 -65 +10 +18 1800 ST470-30T2MI 950 L2 0.5 5 30 7 -55 +18 +35 3200 ST950-30L2MI 1000 T3 0.7 7 25 7 -70 +10 +18 2500 ST1000-30T3MI 1500 T4 0.6 12 35 6 -72 +10 +20 3000 ST1500-30T4MI 50 VDC AT 85 C; 30 VDC AT 125 C 68 T1 1.5 1 5 35 -25 +8 +15 1050 ST68-50T1MI 220 T2 0.9 2 10 17.5 -50 +8 +15 1800 ST220-50T2MI 450 L2 0.6 3 25 7.5 -45 +12 +30 2900 ST450-50L2MI 470 T3 0.75 3 25 10 -45 +8 +15 2100 ST470-50T3MI 680 T4 0.7 5 40 8 -58 +10 +20 2750 ST680-50T4MI 60 VDC AT 85 C; 40 VDC AT 125 C 47 T1 2.0 1 5 44 -25 +8 +12 1050 ST47-60T1MI 150 T2 1.1 2 10 20 -40 +8 +15 1800 ST150-60T2MI 370 L2 0.6 3 25 9 -33 +9 +20 2900 ST370-60L2MI 390 T3 0.9 3 25 15 -45 +8 +15 2100 ST390-60T3MI 560 T4 0.8 5 40 10 -58 +8 +15 2750 ST560-60T4MI 1000 T4 1.0 12 90 20 -90 +30 +50 3200 ST1000-60T4MI 33 T1 2.5 1 5 66 -25 +5 +9 1050 ST33-75T1MI 110 T2 1.3 2 10 24 -35 +6 +10 1650 ST110-75T2MI 250 L2 0.8 5 30 12 -30 +6 +15 2500 ST250-75L2MI 330 T3 1.0 3 30 12 -45 +6 +10 2100 ST330-75T3MI 470 T4 0.9 5 50 12 -50 +6 +10 2750 ST470-75T4MI 75 VDC AT 85 C; 50 VDC AT 125 C Notes * (K = 10 %, M = 20 %) and insulation letter (I = insulation, X = uninsulated) * Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following the letter "X" from "0" to "9". For units with outer plastic-film insulation, substitute "2" for "0" at the end of the part number * For RoHS-compliant add "E3" for suffix Revision: 25-Jun-2018 Document Number: 43000 2 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay STANDARD RATINGS CAPACITANCE AT 25 C AND 120 Hz (F) CASE CODE MAX. ESR 120 Hz () MAX. DCL AT +25 C (A) +85 C / +125 C (A) MAX. CAPACITANCE CHANGE AT MAX. IMP. AT -55 C AND 120 Hz () -55 C (%) +85 C (%) +125 C (%) AC RIPPLE 85 C 40 kHz (mA) RMS PART NUMBER 100 VDC AT 85 C; 65 VDC AT 125 C 15 T1 3.5 1 5 125 -18 +3 +10 1050 ST15-100T1MI 68 T2 2.1 2 10 37 -30 +4 +12 1650 ST68-100T2MI 120 L2 1.0 3 25 20.5 -30 +4 +12 2200 ST120-100L2MI 150 T3 1.6 3 25 22 -35 +6 +12 2100 ST150-100T3MI 220 T4 1.2 5 50 15 -40 +6 +12 2750 ST220-100T4MI 10 T1 5.5 1 +10 1050 ST10-125T1MI 47 T2 2.3 2 10 47 -25 +5 +12 1650 ST47-125T2MI 90 L2 1.3 5 25 25 -22 +4 +15 2000 ST90-125L2MI 125 VDC AT 85 C; 85 VDC AT 125 C 5 175 -15 +3 82 T3 1.8 3 25 40 -35 +5 +12 1950 ST82-125T3MI 100 T3 1.8 3 25 35 -35 +5 +12 2100 ST100-125T3MI 150 T4 1.6 5 50 20 -35 +6 +12 2750 ST150-125T4MI Notes * (K = 10 %, M = 20 %) and insulation letter (I = insulation, X = uninsulated) * Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following the letter "X" from "0" to "9". For units with outer plastic-film insulation, substitute "2" for "0" at the end of the part number * For RoHS-compliant add "E3" for suffix RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE, AND APPLIES PEAK VOLTAGE FREQUENCY OF APPLIED RIPPLE CURRENT 120 Hz 800 Hz 1 kHz 10 kHz 40 kHz 100 kHz AMBIENT STILL 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 AIR TEMP. IN C % of 85 C rated peak voltage 100 % 0.60 0.39 - - 0.71 0.43 - - 0.72 0.46 - - 0.88 0.55 - - 1.0 0.63 - - 1.1 0.69 - - 90 % 0.60 0.46 - - 0.71 0.55 - - 0.72 0.55 - - 0.88 0.67 - - 1.0 0.77 - - 1.1 0.85 - - 80 % 0.60 0.52 0.35 - 0.71 0.62 0.42 - 0.72 0.62 0.42 - 0.88 0.76 0.52 - 1.0 0.87 0.59 - 1.1 0.96 0.65 - 70 % 0.60 0.58 0.44 - 0.71 0.69 0.52 - 0.72 0.70 0.52 - 0.88 0.85 0.64 - 1.0 0.97 0.73 - 1.1 1.07 0.80 - 66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50 Revision: 25-Jun-2018 Document Number: 43000 3 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay TYPICAL PERFORMANCE CHARACTERISTICS OF ST CAPACITORS ELECTRICAL CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Operating temperature range -55 C to +85 C (to +125 C with voltage derating) Capacitor tolerance 20 %, 10 % at 120 Hz, at +25 C Capacitor change by temperature Limit per Standard Ratings table ESR Limit per Standard Ratings table, at +25 C, 120 Hz Impedance Limit per Standard Ratings table, at -55 C, 120 Hz DCL (leakage current) Limit per Standard Ratings table AC ripple current Limit per Standard Ratings table, at +85 C and 40 kHz Reverse voltage There shall be no continuous reverse voltage. Transient reverse voltage surges are acceptable under the following conditions: a) The peak reverse voltage is equal to or less than 1.5 V and the product of the peak current times the duration of the reverse transient is 0.05 As or less b) The repetition rate of the reverse voltage surges is less than 10 Hz Surge voltage Surge voltage shall be in accordance with MIL-PRF-39006 and Table II of DSCC93026. The DC rated surge voltage is the maximum voltage to which the capacitors can be subjected under any conditions including transients and peak ripple at the highest line voltage. The DC surge voltage is 115 % of rated DC voltage. PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Life testing Capacitors shall be capable of withstanding a 2000 h life test at a temperature +85 C at rated voltage, or a 2000 h life test at 125 C test at derated voltage. After the test, the capacitors shall meet the following requirements: a) DC leakage at 85 C and 125 C shall not exceed 125 % of the specified value b) DC leakage at 25 C shall not exceed the specified value c) Capacitance shall be within +10 %, -20 % of initial value d) ESR shall not exceed 200 % of the specified value ENVIRONMENTAL CHARACTERISTICS ITEM CONDITION COMMENTS Seal MIL-PRF-39006 When the capacitors are tested as specified in MIL-PRF-39006, there shall be no evidence of leakage. Moisture resistance MIL-PRF-39006 Moisture resistance shall be in accordance with MIL-PRF-39006. Number of cycles: 10 continuous cycles Barometric pressure (reduced) MIL-STD-202, method 105, condition E Altitude 150 000 feet Revision: 25-Jun-2018 Document Number: 43000 4 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay MECHANICAL CHARACTERISTICS ITEM CONDITION COMMENTS Shock (specified pulse) MIL-STD-202, method 213, condition I (100 g) The capacitors shall meet the requirements of MIL-PRF-39006. Vibration, high frequency MIL-STD-202, method 204, condition D (20 g peak) The capacitors shall meet the requirements of MIL-PRF-39006. Thermal shock MIL-STD-202, method 107, condition A Thermal shock shall be in accordance with MIL-PRF-39006 when tested for 30 cycles. Solderability MIL-STD-202, method 208, ANSI/J-STD-002, test A Solderability shall be in accordance with MIL-PRF-39006. Terminal strength MIL-STD-202, method 211 Terminal strength shall be in accordance with MIL-PRF-39006. Resistance to solder heat MIL-STD-202, method 210, condition C The capacitors shall meet the requirements of MIL-PRF-39006. Terminals MIL-STD-1276 Terminals shall be as specified in MIL-STD-1276. The length and diameter of the terminals shall be as specified in Dimensions table. All terminals shall be permanently secured internally and externally, as applicable. All external joints shall be welded. Marking MIL-STD-1285 Marking of capacitors conforms to method I of MIL-STD-1285 and include capacitance (in F), capacitance tolerance letter, rated voltage, date code, lot symbol and Vishay trademark. SELECTOR GUIDES Tantalum Selector Guide www.vishay.com/doc?49054 Parameter Comparison Guide www.vishay.com/doc?42088 Revision: 25-Jun-2018 Document Number: 43000 5 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000