LFxxAB LFxxC Very low drop voltage regulators with inhibit Features Very low dropout voltage (0.45V) Very low quiescent current (typ. 50 A in OFF mode, 500 A in ON mode) Output current up to 500 mA Logic-controlled electronic shutdown Output voltages of 1.5; 1.8; 2.5; 3.3; 4.7; 5; 6; 8; 8.5; 9; 12V Automotive Grade product: 1.8V, 2.5V, 3.3V, 5.0V, 8.0V, 8.5V VOUT in DPAK and PPAK packages Internal current and thermal limit Only 2.2 F for stability Available in 1% (AB) or 2% (C) selection at 25C Supply voltage rejection: 80db (typ.) Temperature range: -40 to 125 C PPAK Description The LFxxAB/LFxxC are very Low Drop regulators available in PENTAWATT, TO-220, TO-220FP, DPAK and PPAK package and in a wide range of output voltages. The very low drop voltage (0.45 V) and the very low quiescent current make them particularly suitable for low noise, low power applications and specially in battery powered systems. In the 5 pins configuration (PENTAWATT and PPAK) a Shutdown Logic Control function is available (pin 2, TTL compatible). This means that when the device is used as a local regulator, it is possible to Table 1. TO-220FP TO-220 DPAK PENTAWATT put a part of the board in standby, decreasing the total power consumption. In the three terminal configuration the device has the same electrical performance, but is fixed in the ON state. It requires only a 2.2 F capacitor for stability allowing space and cost saving. The LFxx is available as Automotive Grade in DPAK and PPAK packages, for the options of output voltages whose commercial Part Numbers are shown in the Table 32 (order codes). These devices are qualified according to the specification AEC-Q100 of the Automotive market, in the temperature range -40 C to 125 C, and the statistical tests PAT, SYL, SBL are performed. Device summary Part numbers LF15C LF18AB LF33C LF50C LF60AB LF85C LF90AB LF15AB LF25C LF33AB LF50AB LF80C LF85AB LF120C LF18C LF25AB LF47C LF60C LF80AB LF90C LF120AB February 2008 Rev 21 1/49 www.st.com 49 Contents LFxxAB - LFxxC Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 7 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 2/49 LFxxAB - LFxxC List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Dropout voltage vs output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Dropout voltage vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Supply current vs input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Supply current vs input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Short circuit current vs input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Supply current vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Logic controlled precision 3.3/5.0 V selectable output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Sequential multi-output supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Multiple supply with ON/OFF toggle switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Basic inhibit functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Delayed turn-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Low voltage bulb blinker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3/49 List of tables LFxxAB - LFxxC List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. 4/49 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical characteristics for LF15AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electrical characteristics for LF15C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Electrical characteristics for LF18AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electrical characteristics for LF18C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical characteristics for LF18CDT-TRY (Automotive Grade). . . . . . . . . . . . . . . . . . . . 12 Electrical characteristics for LF25AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Electrical characteristics for LF25ABDT-TRY (Automotive Grade). . . . . . . . . . . . . . . . . . . 14 Electrical characteristics for LF25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical characteristics for LF25CDT-TRY (Automotive Grade). . . . . . . . . . . . . . . . . . . . 16 Electrical characteristics for LF33AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Electrical characteristics for LF33C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Electrical characteristics for LF33CDT-TRY and LF33CPT-TRY (Automotive Grade) . . . . 19 Electrical characteristics for LF50AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Electrical characteristics for LF50ABDT-TRY (Automotive Grade). . . . . . . . . . . . . . . . . . . 21 Electrical characteristics for LF50C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Electrical characteristics for LF50CDT-TRY and LF50CPT-TRY (Automotive Grade) . . . . 23 Electrical characteristics for LF60AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Electrical characteristics for LF60C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Electrical characteristics for LF80AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Electrical characteristics for LF80C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Electrical characteristics for LF80CDT-TRY (Automotive Grade). . . . . . . . . . . . . . . . . . . . 28 Electrical characteristics for LF85AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Electrical characteristics for LF85C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Electrical characteristics for LF85CDT-TRY and LF85CPT-TRY (Automotive Grade) . . . . 31 Electrical characteristics for LF90AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Electrical characteristics for LF90C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Electrical characteristics for LF120AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Electrical characteristics for LF120C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 LFxxAB - LFxxC 1 Diagram Figure 1. Block diagram Diagram 5/49 Pin configuration LFxxAB - LFxxC 2 Pin configuration Figure 2. Pin connections (top view) TO-220 TO-220FP DPAK PPAK PENTAWATT 6/49 LFxxAB - LFxxC Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit -0.5 to 40(1) V VI DC input voltage IO Output current Internally Limited PTOT Power dissipation Internally Limited TSTG Storage temperature range -40 to 150 C TOP Operating junction temperature range -40 to 125 C 1. For 18 < VI < 40 the regulator is in shut-down Table 3. Symbol Thermal data Parameter PENTAWATT TO-220 TO-220FP DPAK/PPAK Unit RthJC Thermal resistance junction-case 3 3 5 8 C/W RthJA Thermal resistance junction-ambient 50 50 60 100 C/W Figure 3. Test circuit 7/49 Electrical characteristics LFxxAB - LFxxC 4 Electrical characteristics Table 4. Electrical characteristics for LF15AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Symbol Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 3.5 V 1.485 1.5 1.515 IO = 50 mA, VI = 3.5 V, Ta = -25 to 85C 1.470 1.530 2.5 16 Unit V IO = 500 mA 1 V A VO Line regulation VI = 2.5 to 16 V, IO = 5 mA 2 10 mV VO Load regulation VI = 2.8 V, IO = 5 to 500 mA 2 10 mV 0.5 1 VI = 2.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection mA VI = 2.8 to 16V, IO=500mA VI = 6 V SVR ON MODE IO = 5 mA, VI = 3.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 100 A dB eN Output noise voltage B = 10 Hz to 100 kHz 50 V Vd Dropout voltage IO = 200 mA 1 V VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 8/49 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 5. Symbol Electrical characteristics Electrical characteristics for LF15C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 3.5 V 1.47 1.5 1.53 IO = 50 mA, VI = 3.5 V, Ta = -25 to 85C 1.44 1.56 IO = 500 mA 2.5 16 Unit V 1 V A VO Line regulation VI = 2.5 to 16 V, IO = 5 mA 2 10 mV VO Load regulation VI = 2.8 V, IO = 5 to 500 mA 2 10 mV 0.5 1 VI = 2.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection mA VI = 2.8 to 16V, IO=500mA VI = 6 V SVR ON MODE IO = 5 mA, VI = 3.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 100 A dB eN Output noise voltage B = 10 Hz to 100 kHz 50 V Vd Dropout voltage IO = 200 mA 1 V VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 0.8 2 2 V V 10 A 10 F 9/49 Electrical characteristics Table 6. Symbol LFxxAB - LFxxC Electrical characteristics for LF18AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 3.3 V 1.782 1.8 1.818 IO = 50 mA, VI = 3.3 V, Ta = -25 to 85C 1.764 1.836 3 16 Unit V IO = 500 mA 1 V A VO Line regulation VI = 2.8 to 16 V, IO = 5 mA 2 12 mV VO Load regulation VI = 3.3 V, IO = 5 to 500 mA 2 10 mV 0.5 1 VI = 2.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection mA VI = 3.1 to 16V, IO=500mA VI = 6 V SVR ON MODE IO = 5 mA, VI = 3.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 60 100 A dB eN Output noise voltage B = 10 Hz to 100 kHz 50 V Vd Dropout voltage IO = 200 mA 0.7 V VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 10/49 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 7. Symbol Electrical characteristics Electrical characteristics for LF18C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 3.5 V 1.764 1.8 1.836 IO = 50 mA, VI = 3.5 V, Ta = -25 to 85C 1.728 1.872 3 16 Unit V IO = 500 mA 1 V A VO Line regulation VI = 2.8 to 16 V, IO = 5 mA 2 12 mV VO Load regulation VI = 3.3 V, IO = 5 to 500 mA 2 10 mV 0.5 1 VI = 2.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection mA VI = 3.1 to 16V, IO=500mA VI = 6 V SVR ON MODE IO = 5 mA, VI = 3.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 60 100 A dB eN Output noise voltage B = 10 Hz to 100 kHz 50 V Vd Dropout voltage IO = 200 mA 0.7 V VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 0.8 2 2 V V 10 A 10 F 11/49 Electrical characteristics Table 8. Symbol LFxxAB - LFxxC Electrical characteristics for LF18CDT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 3.5 V, Ta = 25C 1.764 1.8 1.836 IO = 50 mA, VI = 3.5 V 1.713 1.887 3 16 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 2.8 to 16 V, IO = 5 mA 2 15 mV VO Load regulation VI = 3.3 V, IO = 5 to 500 mA 2 15 mV 0.5 2 VI = 2.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 12/49 IO = 5 mA, VI = 3.5 1 V Ta = 25C V A ON MODE mA VI = 3.1 to 16V, IO=500mA VI = 6 V SVR V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 60 120 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F LFxxAB - LFxxC Table 9. Symbol Electrical characteristics Electrical characteristics for LF25AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 4.5 V 2.475 2.5 2.525 IO = 50 mA, VI = 4.5 V, Ta = -25 to 85C 2.450 Unit V 2.550 IO = 500 mA 16 1 V A VO Line regulation VI = 3.5 to 16 V, IO = 5 mA 2 12 mV VO Load regulation VI = 3.8 V, IO = 5 to 500 mA 2 12 mV 0.5 1 VI = 3.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 4.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 3.8 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 13/49 Electrical characteristics Table 10. Symbol LFxxAB - LFxxC Electrical characteristics for LF25ABDT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 4.5 V, Ta = 25C 2.475 2.5 2.525 IO = 50 mA, VI = 4.5 V 2.435 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 3.5 to 16 V, IO = 5 mA 2 15 mV VO Load regulation VI = 3.8 V, IO = 5 to 500 mA 2 15 mV 0.5 2 VI = 3.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 14/49 16 IO = 5 mA, VI = 4.5 1 V Ta = 25C V A ON MODE mA VI = 3.8 to 16V, IO=500mA VI = 6 V SVR V 2.565 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 120 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F LFxxAB - LFxxC Table 11. Symbol Electrical characteristics Electrical characteristics for LF25C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 4.5 V 2.45 2.5 2.55 IO = 50 mA, VI = 4.5 V, Ta = -25 to 85C 2.4 Unit V 2.6 IO = 500 mA 16 1 V A VO Line regulation VI = 3.5 to 16 V, IO = 5 mA 2 12 mV VO Load regulation VI = 3.8 V, IO = 5 to 500 mA 2 12 mV 0.5 1 VI = 3.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 4.5 1 V 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 3.8 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 15/49 Electrical characteristics Table 12. Symbol LFxxAB - LFxxC Electrical characteristics for LF25CDT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 4.5 V, Ta = 25C 2.45 2.5 2.55 IO = 50 mA, VI = 4.5 V 2.385 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 3.5 to 16 V, IO = 5 mA 2 15 mV VO Load regulation VI = 3.8 V, IO = 5 to 500 mA 2 15 mV 0.5 2 VI = 3.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 16/49 16 IO = 5 mA, VI = 4.5 1 V Ta = 25C V A ON MODE mA VI = 3.8 to 16V, IO=500mA VI = 6 V SVR V 2.615 12 OFF MODE 50 f = 120 Hz 82 f = 1 kHz 77 f = 10 kHz 65 120 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F LFxxAB - LFxxC Table 13. Symbol Electrical characteristics Electrical characteristics for LF33AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 5.3 V 3.267 3.3 3.333 IO = 50 mA, VI = 5.3 V, Ta = -25 to 85C 3.234 Unit V 3.366 IO = 500 mA 16 1 V A VO Line regulation VI = 4.3 to 16 V, IO = 5 mA 3 16 mV VO Load regulation VI = 4.6 V, IO = 5 to 500 mA 3 16 mV 0.5 1 VI = 4.3 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 5.3 1 V 12 OFF MODE 50 f = 120 Hz 80 f = 1 kHz 75 f = 10 kHz 65 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 4.6 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 17/49 Electrical characteristics Table 14. Symbol LFxxAB - LFxxC Electrical characteristics for LF33C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 5.3 V 3.234 3.3 3.366 IO = 50 mA, VI = 5.3 V, Ta = -25 to 85C 3.168 Unit V 3.432 IO = 500 mA 16 1 V A VO Line regulation VI = 4.3 to 16 V, IO = 5 mA 3 16 mV VO Load regulation VI = 4.6 V, IO = 5 to 500 mA 3 16 mV 0.5 1 VI = 4.3 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 5.3 1 V 12 OFF MODE 50 f = 120 Hz 80 f = 1 kHz 75 f = 10 kHz 65 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 18/49 mA VI = 4.6 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 15. Symbol Electrical characteristics Electrical characteristics for LF33CDT-TRY and LF33CPT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 5.3 V, Ta = 25C 3.234 3.3 3.366 IO = 50 mA, VI = 5.3 V, 3.153 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 4.3 to 16 V, IO = 5 mA 3 19 mV VO Load regulation VI = 4.6 V, IO = 5 to 500 mA 3 19 mV 0.5 2 VI = 4.3 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 16 IO = 5 mA, VI = 5.3 1 V Ta = 25C V A ON MODE mA VI = 4.6 to 16V, IO=500mA VI = 6 V SVR V 3.447 12 OFF MODE 50 f = 120 Hz 80 f = 1 kHz 75 f = 10 kHz 65 120 dB B = 10 Hz to 100 KHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F 19/49 Electrical characteristics Table 16. Symbol LFxxAB - LFxxC Electrical characteristics for LF50AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 7 V 4.95 5 5.05 IO = 50 mA, VI = 7 V, Ta = -25 to 85C 4.9 Unit V 5.1 IO = 500 mA 16 1 V A VO Line regulation VI = 6 to 16 V, IO = 5 mA 5 25 mV VO Load regulation VI = 6.3 V, IO = 5 to 500 mA 5 25 mV 0.5 1 VI = 6 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 7 1 V 12 OFF MODE 50 f = 120 Hz 76 f = 1 kHz 71 f = 10 kHz 60 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 20/49 mA VI = 6.3 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 17. Symbol Electrical characteristics Electrical characteristics for LF50ABDT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 7 V, Ta = 25C 4.95 5 5.05 IO = 50 mA, VI = 7 V 4.885 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 6 to 16 V, IO = 5 mA 5 28 mV VO Load regulation VI = 6.3 V, IO = 5 to 500 mA 5 28 mV 0.5 2 VI = 6 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 16 IO = 5 mA, VI = 7 1 V Ta = 25C V A ON MODE mA VI = 6.3 to 16V, IO=500mA VI = 6 V SVR V 5.115 12 OFF MODE 50 f = 120 Hz 76 f = 1 kHz 71 f = 10 kHz 60 120 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F 21/49 Electrical characteristics Table 18. Symbol LFxxAB - LFxxC Electrical characteristics for LF50C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 7 V 4.9 5 5.1 IO = 50 mA, VI = 7 V, Ta = -25 to 85C 4.8 Unit V 5.2 IO = 500 mA 16 1 V A VO Line regulation VI = 6 to 16 V, IO = 5 mA 5 25 mV VO Load regulation VI = 6.3 V, IO = 5 to 500 mA 5 25 mV 0.5 1 VI = 6 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 7 1 V 12 OFF MODE 50 f = 120 Hz 76 f = 1 kHz 71 f = 10 kHz 60 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 6 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 22/49 mA VI = 6.3 to 16V, IO=500mA VI = 6 V SVR ON MODE 100 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 19. Symbol Electrical characteristics Electrical characteristics for LF50CDT-TRY and LF50CPT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions IO = 50 mA, VI = 7 V, Ta = 25C Min. Typ. Max. 4.9 5 5.1 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 6 to 16 V, IO = 5 mA 5 28 mV VO Load regulation VI = 6.3 V, IO = 5 to 500 mA 5 28 mV 0.5 2 IO = 50 mA, VI = 7 V VI = 6 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 5.215 16 IO = 5 mA, VI = 7 1 V Ta = 25C V A ON MODE mA VI = 6.3 to 16V, IO=500mA VI = 6 V SVR V 4.785 12 OFF MODE 50 f = 120 Hz 76 f = 1 kHz 71 f = 10 kHz 60 120 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 6 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F 23/49 Electrical characteristics Table 20. Symbol LFxxAB - LFxxC Electrical characteristics for LF60AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 8 V 5.94 6 6.06 IO = 50 mA, VI = 8 V, Ta = -25 to 85C 5.88 Unit V 6.12 IO = 500 mA 16 1 V A VO Line regulation VI = 7 to 16 V, IO = 5 mA 6 30 mV VO Load regulation VI = 7.3 V, IO = 5 to 500 mA 6 30 mV 0.7 1.5 VI = 7 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 8 1 V 12 OFF MODE 70 f = 120 Hz 75 f = 1 kHz 70 f = 10 kHz 60 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 24/49 mA VI = 7.3 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 21. Symbol Electrical characteristics Electrical characteristics for LF60C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 8 V 5.88 6 6.12 IO = 50 mA, VI = 8 V, Ta = -25 to 85C 5.76 Unit V 6.24 IO = 500 mA 16 1 V A VO Line regulation VI = 7 to 16 V, IO = 5 mA 6 30 mV VO Load regulation VI = 7.3 V, IO = 5 to 500 mA 6 30 mV 0.7 1.5 VI = 7 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 8 1 V 12 OFF MODE 70 f = 120 Hz 75 f = 1 kHz 70 f = 10 kHz 60 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 7.3 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 25/49 Electrical characteristics Table 22. Symbol LFxxAB - LFxxC Electrical characteristics for LF80AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 10 V 7.92 8 8.08 IO = 50 mA, VI = 10 V, Ta = -25 to 85C 7.84 Unit V 8.16 IO = 500 mA 16 1 V A VO Line regulation VI = 9 to 16 V, IO = 5 mA 8 40 mV VO Load regulation VI = 9.3 V, IO = 5 to 500 mA 8 40 mV 0.7 1.5 VI = 9 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 10 1 V 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 26/49 mA VI = 9.3 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 23. Symbol Electrical characteristics Electrical characteristics for LF80C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 10 V 7.84 8 8.16 IO = 50 mA, VI = 10 V, Ta = -25 to 85C 7.68 Unit V 8.32 IO = 500 mA 16 1 V A VO Line regulation VI = 9 to 16 V, IO = 5 mA 8 40 mV VO Load regulation VI = 9.3 V, IO = 5 to 500 mA 8 40 mV 0.7 1.5 VI = 9 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 10 1 V 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 9.3 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 27/49 Electrical characteristics Table 24. Symbol LFxxAB - LFxxC Electrical characteristics for LF80CDT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 125C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 10 V, Ta = 25C 7.84 8 8.16 IO = 50 mA, VI = 10 V 7.665 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 9 to 16 V, IO = 5 mA 8 44 mV VO Load regulation VI = 9.3 V, IO = 5 to 500 mA 8 44 mV 0.7 2.5 VI = 9 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 28/49 16 IO = 5 mA, VI = 10 1 V Ta = 25C V A ON MODE mA VI = 9.3 to 16V, IO=500mA VI = 9 V SVR V 8.335 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 160 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 9 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F LFxxAB - LFxxC Table 25. Symbol Electrical characteristics Electrical characteristics for LF85AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 10.5 V 8.415 8.5 8.585 IO = 50 mA, VI = 10.5 V, Ta = -25 to 85C 8.33 Unit V 8.67 IO = 500 mA 16 1 V A VO Line regulation VI = 9.5 to 16 V, IO = 5 mA 8 42 mV VO Load regulation VI = 9.8 V, IO = 5 to 500 mA 8 42 mV 0.7 1.5 VI = 9.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 10.5 1 V 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA VI = 9.8 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 29/49 Electrical characteristics Table 26. Symbol LFxxAB - LFxxC Electrical characteristics for LF85C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 10.5 V 8.33 8.5 8.67 IO = 50 mA, VI = 10.5 V, Ta = -25 to 85C 8.16 Unit V 8.84 IO = 500 mA 16 1 V A VO Line regulation VI = 9.5 to 16 V, IO = 5 mA 8 42 mV VO Load regulation VI = 9.8 V, IO = 5 to 500 mA 8 42 mV 0.7 1.5 VI = 9.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection IO = 5 mA, VI = 10.5 1 V 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 9 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 30/49 mA VI = 9.8 to 16V, IO=500mA VI = 9 V SVR ON MODE 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 27. Symbol Electrical characteristics Electrical characteristics for LF85CDT-TRY and LF85CPT-TRY (Automotive Grade) (refer to the test circuits, TA = -40 to 25C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter Test conditions Min. Typ. Max. IO = 50 mA, VI = 10.5 V, Ta = 25C 8.33 8.5 8.67 IO = 50 mA, VI = 10.5 V 8.145 Unit VO Output voltage VI Operating input voltage IO = 500 mA IO Output current limit Ta = 25C 1 VO Line regulation VI = 9.5 to 16 V, IO = 5 mA 8 44 mV VO Load regulation VI = 9.8 V, IO = 5 to 500 mA 8 44 mV 0.7 2.5 VI = 9.5 to 16V, IO = 0mA Id Quiescent current Supply voltage rejection eN Output noise voltage Vd Dropout voltage VIL Control input logic low VIH Control input logic high II CO 16 IO = 5 mA, VI = 10.5 1 V Ta = 25C V A ON MODE mA VI = 9.8 to 16V, IO=500mA VI = 9 V SVR V 8.855 12 OFF MODE 70 f = 120 Hz 72 f = 1 kHz 67 f = 10 kHz 57 160 dB B = 10 Hz to 100 kHz, Ta = 25C 50 IO = 200 mA 0.2 1.3 IO = 500 mA 0.4 1.3 V V 0.8 2 Control input current VI = 9 V, VC = 6 V, Ta = 25C Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA A 2 V V 10 A 10 F 31/49 Electrical characteristics Table 28. Symbol LFxxAB - LFxxC Electrical characteristics for LF90AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 11 V 8.91 9 9.09 IO = 50 mA, VI = 11 V, Ta = -25 to 85C 8.82 Unit V 9.18 IO = 500 mA 16 1 V A VO Line regulation VI = 10 to 16 V, IO = 5 mA 9 45 mV VO Load regulation VI = 10.3 V, IO = 5 to 500 mA 9 45 mV 0.7 1.5 VI = 10 to 16V, IO = 0mA Id SVR Quiescent current Supply voltage rejection VI = 10.3 to 16V, IO = 500mA ON MODE VI = 10 V OFF MODE 70 f = 120 Hz 71 f = 1 kHz 66 f = 10 kHz 56 IO = 5 mA, VI = 11 1 V eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 10 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 32/49 mA 12 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 29. Symbol Electrical characteristics Electrical characteristics for LF90C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 11 V 8.82 9 9.18 IO = 50 mA, VI = 11 V, Ta = -25 to 85C 8.64 Unit V 9.36 IO = 500 mA 16 1 V A VO Line regulation VI = 10 to 16 V, IO = 5 mA 9 45 mV VO Load regulation VI = 10.3 V, IO = 5 to 500 mA 9 45 mV 0.7 1.5 VI = 10 to 16V, IO = 0mA Id SVR Quiescent current Supply voltage rejection VI = 10.3 to 16V, IO = 500mA ON MODE VI = 10 V OFF MODE 70 f = 120 Hz 71 f = 1 kHz 66 f = 10 kHz 56 IO = 5 mA, VI = 11 1 V eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 10 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA 12 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 33/49 Electrical characteristics Table 30. Symbol LFxxAB - LFxxC Electrical characteristics for LF120AB (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified.) Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 15 V 11.88 12 12.12 IO = 50 mA, VI = 15 V, Ta = -25 to 85C 11.76 Unit V 12.24 IO = 500 mA 16 1 V A VO Line regulation VI = 13 to 16 V, IO = 5 mA 12 60 mV VO Load regulation VI = 13.3 V, IO = 5 to 500 mA 12 60 mV VI = 13 to 16V, IO = 0mA 0.7 1.5 Id SVR Quiescent current Supply voltage rejection VI = 13.3 to 16V, IO = 500mA ON MODE VI = 13 V OFF MODE 70 f = 120 Hz 69 f = 1 kHz 64 f = 10 kHz 54 IO = 5 mA, VI = 14 1 V eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 13 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO 34/49 mA 12 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F LFxxAB - LFxxC Table 31. Symbol Electrical characteristics Electrical characteristics for LF120C (refer to the test circuits, TJ = 25 C, CI = 0.1 F, CO = 2.2 F unless otherwise specified). Parameter VO Output voltage VI Operating input voltage IO Output current limit Test conditions Min. Typ. Max. IO = 50 mA, VI = 14 V 11.76 12 12.24 IO = 50 mA, VI = 14 V, Ta = -25 to 85C 11.52 Unit V 12.48 IO = 500 mA 16 1 V A VO Line regulation VI = 13 to 16 V, IO = 5 mA 12 60 mV VO Load regulation VI = 13.3 V, IO = 5 to 500 mA 12 60 mV VI = 13 to 16V, IO = 0mA 0.7 1.5 Id SVR Quiescent current Supply voltage rejection VI = 13.3 to 16V, IO = 500mA ON MODE VI = 13 V OFF MODE 70 f = 120 Hz 69 f = 1 kHz 64 f = 10 kHz 54 IO = 5 mA, VI = 14 1 V eN Output noise voltage Vd Dropout voltage VIL Control input logic low Ta = -40 to 125C VIH Control input logic high Ta = -40 to 125C Control input current VI = 13 V, VC = 6 V Output bypass capacitance ESR = 0.1 to 10 , IO = 0 to 500 mA II CO mA 12 140 A dB B = 10 Hz to 100 kHz 50 V IO = 200 mA 0.2 0.35 IO = 500 mA 0.4 0.7 V 0.8 2 2 V V 10 A 10 F 35/49 Typical performance characteristics LFxxAB - LFxxC 5 Typical performance characteristics Figure 4. (unless otherwise specified VO(NOM) = 3.3 V) Dropout voltage vs output current Figure 5. Dropout voltage vs temperature Figure 6. Supply current vs input voltage Figure 7. Supply current vs input voltage Figure 8. Short circuit current vs input voltage Figure 9. Supply current vs temperature 36/49 LFxxAB - LFxxC Typical performance characteristics Figure 10. Logic controlled precision 3.3/5.0 V selectable output Figure 11. Sequential multi-output supply 37/49 Typical performance characteristics Figure 12. Multiple supply with ON/OFF toggle switch Figure 13. Basic inhibit functions 38/49 LFxxAB - LFxxC LFxxAB - LFxxC Typical performance characteristics Figure 14. Delayed turn-on Figure 15. Low voltage bulb blinker 39/49 Package mechanical data 6 LFxxAB - LFxxC Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 40/49 LFxxAB - LFxxC Package mechanical data PENTAWATT (Vertical) mechanical data Dim. A C D D1 E F F1 G G1 H2 H3 L L1 L2 L3 L5 L6 L7 M M1 Dia1 Min. 2.4 1.2 0.35 0.8 1 3.2 6.6 mm. Typ. 3.4 6.8 10.05 Max. 4.8 1.37 2.8 1.35 0.55 1.05 1.4 3.6 7 10.4 10.4 Min. inch. Typ. 0.094 0.047 0.014 0.031 0.039 0.126 0.260 0.134 0.268 0.396 17.85 15.75 21.4 22.5 2.6 15.1 6 0.703 0.620 0.843 0.886 3 15.8 6.6 0.102 0.594 0.236 4.5 4 3.65 Max. 0.189 0.054 0.110 0.053 0.022 0.041 0.055 0.142 0.276 0.409 0.409 0.118 0.622 0.260 0.177 0.157 3.85 0.144 0.152 P010E 41/49 Package mechanical data LFxxAB - LFxxC TO-220 mechanical data Dim. mm. Min. Max. Min. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 D1 Typ. inch. 1.27 Typ. Max. 0.107 0.050 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 L2 L4 16.4 13.0 0.409 0.645 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 P011C 42/49 LFxxAB - LFxxC Package mechanical data TO-220FP mechanical data Dim. mm. Min. Max. Min. A 4.40 4.60 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.50 0.045 0.059 F2 1.15 1.50 0.045 0.059 G 4.95 5.2 0.194 0.204 G1 2.4 2.7 0.094 0.106 H 10.0 10.40 0.393 0.409 L2 Typ inch. 16 Typ. Max. 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 0.385 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.645 L7 9 9.3 0.354 0.366 DIA. 3 3.2 0.118 0.126 7012510A-H 43/49 Package mechanical data LFxxAB - LFxxC DPAK mechanical data mm. inch. Dim. Min. A A1 A2 B b4 C C2 D D1 E E1 e e1 H L (L1) L2 L4 R V2 Typ. 2.2 0.9 0.03 0.64 5.2 0.45 0.48 6 Max. Min. 2.4 1.1 0.23 0.9 5.4 0.6 0.6 6.2 0.086 0.035 0.001 0.025 0.204 0.017 0.019 0.236 6.6 0.252 5.1 6.4 0.260 0.173 0.368 0.039 2.8 0.8 0.181 0.397 0.110 0.031 1 0.023 0.2 0 0.094 0.043 0.009 0.035 0.212 0.023 0.023 0.244 0.185 0.090 4.6 10.1 0.6 Max. 0.200 4.7 2.28 4.4 9.35 1 Typ. 0.039 0.008 8 0 8 0068772-F 44/49 LFxxAB - LFxxC Package mechanical data PPAK mechanical data mm. inch. Dim. Min. A Typ. 2.2 Max. Min. Typ. Max. 2.4 0.086 0.094 A1 0.9 1.1 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.4 0.6 0.015 0.023 B2 5.2 5.4 0.204 0.212 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 0.244 D1 E 5.1 6.4 0.201 6.6 0.252 0.260 E1 4.7 0.185 e 1.27 0.050 G 4.9 5.25 0.193 G1 2.38 2.7 0.093 0.106 H 9.35 10.1 0.368 0.397 0.039 L2 0.8 L4 0.6 L5 1 L6 1 1 2.8 0.206 0.031 0.023 0.039 0.039 0.110 0078180-E 45/49 Package mechanical data LFxxAB - LFxxC Tape & reel DPAK-PPAK mechanical data mm. inch. Dim. Min. Typ. A Min. Typ. 330 13.0 13.2 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 46/49 Max. 0.504 0.512 22.4 0.519 0.882 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 LFxxAB - LFxxC Order codes 7 Order codes Table 32. Order codes Packages TO-220 LF15CV(1) LF15ABV(1) TO-220FP DPAK DPAK (T&R) PPAK (1) LF15CP LF15CPT LF15ABP(1) LF15ABDT-TR (1) PPAK (T&R) (1) LF15ABPT(1) LF18CDT-TR LF18CP LF15CPT-TR(1) LF18ABP LF25CP(1) LF18CPT-TR LF18ABDT-TR LF18ABPT-TR 1.8 V LF25CDT-TR LF25CPT-TR 2.5 V LF25ABDT-TR LF25ABP 2.5 V LF25ABPT(1) 2.5 V (2) 2.5 V LF25ABDT-TRY LF33CV LF33ABV LF33CDT-TR LF33CPT-TR 3.3 V LF33CDT-TRY(2) LF33CPT-TRY(2) 3.3 V LF33ABDT-TR 3.3 V LF47CV LF50CV 4.7 V LF50CP LF50CDT-TR (2) LF50CDT-TRY LF50ABV LF50ABP LF50ABDT-TR LF50CPT-TR 5V LF50CPT-TRY(2) 5V LF50ABPT-TR 5V LF50ABDT-TRY(2) LF60CV LF60CP(1) LF60ABV LF60ABP(1) LF80CV 5V LF60CDT-TR LF60ABDT-TR (1) LF60ABPT(1) LF80CDT-TR LF80CP LF60CPT-TR(1) 6V LF60ABPT-TR(1) 6V LF80CPT-TR 8V (2) 8V LF80CDT-TRY LF80ABV 1.8 V 1.8 V LF25CDT-TRY(2) (1) 1.5 V 1.5 V LF18CDT-TRY(2) (1) Output voltage LF80ABP(1) LF80ABDT-TR LF80ABPT-TR 8V LF85CP LF85CDT-TR LF85CPT-TR 8.5 V LF85CDT-TRY(2) LF90CP(1) LF90ABV LF90ABP(1) 8.5 V LF90CDT-TR LF90CPT-TR 9V LF120CP (1) LF90ABDT-TR LF90ABPT-TR 9V LF120ABV LF85ABPT (1) LF90ABDT 8.5 V LF85ABPT-TR LF85ABP LF90CV LF85CPT-TRY (1) (2) LF120CDT-TR LF120ABDT-TR 12 V (1) LF120ABPT 12 V 1. Available on request. 2. Automotive Grade products. 47/49 Revision history LFxxAB - LFxxC 8 Revision history Table 33. Document revision history Date Revision 21-Jun-2004 14 Document updating. 24-May-2006 15 Order codes updated. 02-Apr-2007 16 Order codes updated. 14-May-2007 17 Order codes updated. 26-Jul-2007 18 Add Table 1 in cover page. 26-Nov-2007 19 Modified: Table 32. 16-Jan-2008 20 Added new order codes for Automotive grade products see Table 32 on page 47. 12-Feb-2008 21 Modified: Table 32 on page 47. 48/49 Changes LFxxAB - LFxxC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 49/49