UCC27524DGNR - Texas Instruments

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

UCC27523

Dual Inverting Inputs

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

UCC27524

Dual Non-Inverting Inputs

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

UCC27525

One Inverting and One

Non-Inverting Input

INA-

INB-

GND

OUTB

INA+

INB+

OUTA

VDD

UCC27526

Dual Input Configuration

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

UCC2752x Dual 5-A High-Speed, Low-Side Gate Driver

1 Features 3 Description

The UCC2752x family of devices are dual-channel,

1• Industry-Standard Pinout high-speed, low-side gate-driver devices capable of

• Two Independent Gate-Drive Channels effectively driving MOSFET and IGBT power

• 5-A Peak Source and Sink-Drive Current switches. Using a design that inherently minimizes

shoot-through current, UCC2752x can deliver high-

• Independent-Enable Function for Each Output peak current pulses of up to 5-A source and 5-A sink

• TTL and CMOS Compatible Logic Threshold into capacitive loads along with rail-to-rail drive

Independent of Supply Voltage capability and extremely small propagation delay

• Hysteretic-Logic Thresholds for High Noise (typically 13 ns). In addition, the drivers feature

Immunity matched internal propagation delays between the two

channels. These delays are very well suited for

• Inputs and Enable Pin-Voltage Levels Not applications requiring dual-gate drives with critical

Restricted by VDD Pin Bias Supply Voltage timing, such as synchronous rectifiers. This also

• 4.5-V to 18-V Single-Supply Range enables connecting two channels in parallel to

• Outputs Held Low During VDD-UVLO, (Ensures effectively increase current-drive capability or driving

Glitch-Free Operation at Power up and Power two switches in parallel with one input signal. The

input pin thresholds are based on TTL and CMOS

Down) compatible low-voltage logic, which is fixed and

• Fast Propagation Delays (13-ns Typical) independent of the VDD supply voltage. Wide

• Fast Rise and Fall Times (7-ns and 6-ns Typical) hysteresis between the high and low thresholds offers

• 1-ns Typical Delay Matching Between Two excellent noise immunity.

Channels Device Information(1)

• Two Outputs are in Parallel for Higher Drive PART NUMBER PACKAGE BODY SIZE (NOM)

Current SOT-23 (8) 4.90 mm × 3.91 mm

• Outputs Held Low When Inputs Floating UCC27523 HVSSOP (8)

• PDIP (8), SOIC (8), MSOP (8) PowerPAD™ and 3.00 mm × 3.00 mm

WSON (8)

3-mm × 3-mm WSON-8 Package Options SOT-23 (8) 4.90 mm × 3.91 mm

• Operating Temperature Range of –40°C to 140°C HVSSOP (8)

UCC27524 3.00 mm × 3.00 mm

WSON (8)

2 Applications PDIP (8) 9.81 mm × 6.35 mm

• Switched-Mode Power Supplies SOT-23 (8) 4.90 mm × 3.91 mm

• DC-DC Converters UCC27525 HVSSOP (8)

• Motor Control, Solar Power 3.00 mm × 3.00 mm

WSON (8)

• Gate Drive for Emerging Wide Band-Gap Power UCC27526 WSON (8) 3.00 mm × 3.00 mm

Devices such as GaN (1) For all available packages, see the orderable addendum at

the end of the data sheet.

Pin Configuration

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Table of Contents

8.3 Feature Description................................................. 13

1 Features.................................................................. 18.4 Device Functional Modes........................................ 20

2 Applications ........................................................... 19 Application and Implementation ........................ 21

3 Description............................................................. 19.1 Application Information............................................ 21

4 Revision History..................................................... 29.2 Typical Application.................................................. 21

5 Description (continued)......................................... 410 Power Supply Recommendations ..................... 26

6 Pin Configuration and Functions......................... 411 Layout................................................................... 26

7 Specifications......................................................... 611.1 Layout Guidelines ................................................. 26

7.1 Absolute Maximum Ratings ...................................... 611.2 Layout Example .................................................... 27

7.2 ESD Ratings.............................................................. 611.3 Thermal Considerations........................................ 27

7.3 Recommended Operating Conditions....................... 612 Device and Documentation Support................. 29

7.4 Thermal Information.................................................. 612.1 Related Links ........................................................ 29

7.5 Electrical Characteristics........................................... 712.2 Trademarks........................................................... 29

7.6 Switching Characteristics.......................................... 812.3 Electrostatic Discharge Caution............................ 29

7.7 Typical Characteristics.............................................. 912.4 Glossary................................................................ 29

8 Detailed Description............................................ 12 13 Mechanical, Packaging, and Orderable

8.1 Overview................................................................. 12 Information........................................................... 29

8.2 Functional Block Diagrams ..................................... 12

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision F (May, 2013) to Revision G Page

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional

Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device

and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1

• Changed UCC2752X Gate Driver Output Structure image.................................................................................................. 17

Changes from Revision E (June 2012) to Revision F Page

• Added 0.5 to PSW equation in Drive Current and Power Dissipation section....................................................................... 24

Changes from Revision D (April 2012) to Revision E Page

• Added OUTA, OUTB voltage field and values. ...................................................................................................................... 6

• Changed table note from "Values are verified by characterization and are not production tested." to "Values are

verified by characterization on bench."................................................................................................................................... 6

• Added note, "Values are verified by characterization and are not production tested.".......................................................... 6

• Changed Switching Time tPW values from 10 ns and 25 ns to 15 ns and 25 ns ns............................................................... 7

• Changed Functional Block Diagrams images....................................................................................................................... 12

• Changed Slow Input Signal Figure 33.................................................................................................................................. 18

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Changes from Revision C (March 2012) to Revision D Page

• Changed Inputs (INA, INB, INA+, INA–, INB+, INB-) section to include UCC2752X (D, DGN, DSD) information................ 7

• Added Inputs (INA, INB, INA+, INA-, INB+, INB-) UCC27524P ONLY section. .................................................................... 7

• Changed Enable (ENA, ENB) section to include UCC2752X (D, DGN, DSD) information.................................................... 7

• Added ENABLE (ENA, ENB) UCC27524P ONLY section..................................................................................................... 7

Changes from Revision B ( December 2011) to Revision C Page

• Added ROH note in the Outputs (OUTA, OUTB) section. ....................................................................................................... 7

• Added an updated Output Stage section. ............................................................................................................................ 17

• Added UCC2752X Gate Driver Output Structure image...................................................................................................... 17

• Added an updated Low Propagation Delays and Tightly Matched Outputs section............................................................ 18

• Added Slow Input Signal Combined with Differences in Input Threshold Voltage image.................................................... 18

• Added updated Drive Current and Power Dissipation section............................................................................................. 23

• Added a PSW... equation..................................................................................................................................................... 24

Changes from Revision A (November 2011) to Revision B Page

• Changed Supply start threshold row to include two temperature ranges............................................................................... 7

• Changed Minimum operating voltage after supply start min and max values from 3.6 V to 4.2 V to 3.40 V and 4.40 V...... 7

• Changed Supply voltage hysteresis typ value from 0.35 to 0.30........................................................................................... 7

• Changed UCC27526 Block Diagram drawing...................................................................................................................... 13

• Changed UCC27526 Channel A in Inverting and Channel B in Non-Inverting Configuration drawing................................ 21

Changes from Original (November 2011) to Revision A Page

• Changed data sheet status to Production Data...................................................................................................................... 1

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

INA-

INB-

GND

OUTB

INA+

INB+

OUTA

VDD

INA-

INB-

GND

OUTB

INA+

INB+

OUTA

VDD

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

5 Description (continued)

The UCC2752x family provide the combination of three standard logic options — dual inverting, dual

noninverting, one inverting and one noninverting driver. UCC27526 features a dual input design which offers

flexibility of both inverting (IN– pin) and non-inverting (IN+ pin) configuration for each channel. Either IN+ or IN–

pin controls the state of the driver output. The unused input pin is used for enable and disable functions. For

safety purpose, internal pullup and pulldown resistors on the input pins of all the devices in UCC2752x family

ensure that outputs are held LOW when input pins are in floating condition. The UCC27523, UCC27524, and

UCC27525 devices feature Enable pins (ENA and ENB) to have better control of the operation of the driver

applications. The pins are internally pulled up to VDD for active-high logic and are left open for standard

operation.

UCC2752x family of devices are available in SOIC-8 (D), MSOP-8 with exposed pad (DGN) and 3-mm × 3-mm

WSON-8 with exposed pad (DSD) packages. UCC27524 is also offered in PDIP-8 (P) package. UCC27526 is

only offered in 3-mm × 3-mm WSON (DSD) package.

6 Pin Configuration and Functions

D, DGN, or P Package UCC2752(3,4,5) DSD Package UCC2752(3,4,5)

8-Pin SOT-23, HVSSOP, or PDIP 8-Pin WSON

Top View Top View

DSD Package UCC27526

8-Pin WSON

Top View

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Pin Functions (UCC27523 / UCC27524 / UCC27525)

PIN I/O DESCRIPTION

NO. NAME

Enable input for Channel A: ENA biased LOW Disables Channel A output regardless of INA state,

1 ENA I ENA biased HIGH or floating Enables Channel A output, ENA allowed to float hence the pin-to-pin

compatibility with UCC2732X N/C pin.

Input to Channel A: Inverting Input in UCC27523, Non-Inverting Input in UCC27524, Inverting

2 INA I Input in UCC27525, OUTA held LOW if INA is unbiased or floating.

3 GND - Ground: All signals referenced to this pin.

Input to Channel B: Inverting Input in UCC27523, Non-Inverting Input in UCC27524, Non-Inverting

4 INB I Input in UCC27525, OUTB held LOW if INB is unbiased or floating.

5 OUTB O Output of Channel B

6 VDD I Bias supply input

7 OUTA O Output of Channel A

Enable input for Channel B: ENB biased LOW Disables Channel B output regardless of INB state,

8 ENB I ENB biased HIGH or floating Enables Channel B output, ENB allowed to float hence the pin-to-pin

compatibility with UCC2732X N/C pin.

Pin Functions (UCC27526)

PIN I/O DESCRIPTION

NO. NAME

Inverting Input to Channel A: When Channel A is used in Non-Inverting configuration, connect

1 INA– I INA– to GND in order to Enable Channel A output, OUTA held LOW if INA– is unbiased or floating.

Inverting Input to Channel B: When Channel B is used in Non-Inverting configuration, connect

2 INB– I INB– to GND in order to Enable Channel B output, OUTB held LOW if INB– is unbiased or floating.

3 GND - Ground: All signals referenced to this pin.

4 OUTB I Output of Channel B

5 VDD O Bias Supply Input

6 OUTA I Output of Channel A

Non-Inverting Input to Channel B: When Channel B is used in Inverting configuration, connect

7 INB+ O INB+ to VDD in order to Enable Channel B output, OUTB held LOW if INB+ is unbiased or floating.

Non-Inverting Input to Channel A: When Channel A is used in Inverting configuration, connect

8 INA+ I INA+ to VDD in order to Enable Channel A output, OUTA held LOW if INA+ is unbiased or floating.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

7 Specifications

7.1 Absolute Maximum Ratings(1)(2)

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

Supply voltage VDD –0.3 20

DC –0.3 VDD + 0.3 V

OUTA, OUTB voltage Repetitive pulse < 200 ns(3) –2 VDD + 0.3

Output continuous source/sink IOUT_DC 0.3

current A

Output pulsed source/sink current IOUT_pulsed 5

(0.5 µs)

INA, INB, INA+, INA–, INB+, INB–, ENA, ENB voltage(4) –0.3 20 V

Operating virtual junction temperature, TJ–40 150

Soldering, 10 s 300 °C

Lead temperature Reflow 260

Storage temperature, Tstg –65 150 °C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating

Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) All voltages are with respect to GND unless otherwise noted. Currents are positive into, negative out of the specified terminal. See

Mechanical, Packaging, and Orderable Information for thermal limitations and considerations of packages.

(3) Values are verified by characterization on bench.

(4) The maximum voltage on the Input and Enable pins is not restricted by the voltage on the VDD pin.

7.2 ESD Ratings VALUE UNIT

Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±4000

V(ESD) Electrostatic discharge V

Charged-device model (CDM), per JEDEC specification JESD22- ±1000

C101(2)

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT

Supply voltage, VDD 4.5 12 18 V

Operating junction temperature –40 140 °C

Input voltage, INA, INB, INA+, INA–, INB+, INB– 0 18 V

Enable voltage, ENA and ENB 0 18

7.4 Thermal Information UCC27523/4/5 UCC27524 UCC27523/4/5/6

THERMAL METRIC(1) SOIC (D) MSOP (DGN) PDIP (P) WSON (DSD) UNIT

8 PINS 8 PINS 8 PINS 8 PINS

RθJA Junction-to-ambient thermal resistance 130.9 71.8 62.1 46.7

RθJC(top) Junction-to-case (top) thermal resistance 80 65.6 52.7 46.7

RθJB Junction-to-board thermal resistance 71.4 7.4 39.1 22.4 °C/W

ψJT Junction-to-top characterization parameter 21.9 7.4 31 0.7

ψJB Junction-to-board characterization parameter 70.9 31.5 39.1 22.6

RθJC(bot) Junction-to-case (bottom) thermal resistance – 19.6 – 9.5

(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

7.5 Electrical Characteristics

VDD = 12 V, TA= TJ= –40°C to 140°C, 1-µF capacitor from VDD to GND. Currents are positive into, negative out of the

specified terminal (unless otherwise noted,)

PARAMETER TEST CONDITION MIN TYP MAX UNIT

BIAS CURRENTS

VDD = 3.4 V,

INA = VDD, 55 110 175

Start-up current, INB = VDD

IDD(off) (based on UCC27524 Input μA

VDD = 3.4 V,

configuration) INA = GND, 25 75 145

INB = GND

UNDERVOLTAGE LOCKOUT (UVLO)

TJ= 25°C 3.91 4.2 4.5

VON Supply start threshold TJ= –40°C to 140°C 3.7 4.2 4.65 V

Minimum operating voltage

VOFF 3.4 3.9 4.4

after supply start

VDD_H Supply voltage hysteresis 0.2 0.3 0.5

INPUTS (INA, INB, INA+, INA–, INB+, INB–), UCC2752X (D, DGN, DSD)

Output high for non-inverting input pins

VIN_H Input signal high threshold 1.9 2.1 2.3

Output low for inverting input pins

Output low for non-inverting input pins V

VIN_L Input signal low threshold 1 1.2 1.4

Output high for inverting input pins

VIN_HYS Input hysteresis 0.7 0.9 1.1

INPUTS (INA, INB, INA+, INA–, INB+, INB–) UCC27524P ONLY

Output high for non-inverting input pins

VIN_H Input signal high threshold 2.3

Output low for inverting input pins

Output low for non-inverting input pins V

VIN_L Input signal low threshold 1

Output high for inverting input pins

VIN_HYS Input hysteresis 0.9

ENABLE (ENA, ENB) UCC2752X (D, DGN, DSD)

VEN_H Enable signal high threshold Output enabled 1.9 2.1 2.3

VEN_L Enable signal low threshold Output disabled 0.95 1.15 1.35 V

VEN_HYS Enable hysteresis 0.7 0.95 1.1

ENABLE (ENA, ENB) UCC27524P ONLY

VEN_H Enable signal high threshold Output enabled 2.3

VEN_L Enable signal low threshold Output disabled 0.95 V

VEN_HYS Enable hysteresis 0.95

OUTPUTS (OUTA, OUTB)

ISNK/SRC Sink/source peak current(1) CLOAD = 0.22 µF, FSW = 1 kHz ±5 A

VDD-VOH High output voltage IOUT = –10 mA 0.075 V

VOL Low output voltage IOUT = 10 mA 0.01

ROH Output pullup resistance(2) IOUT = –10 mA 2.5 5 7.5 Ω

ROL Output pulldown resistance IOUT = 10 mA 0.15 0.5 1 Ω

(1) Ensured by design.

(2) ROH represents on-resistance of only the P-Channel MOSFET device in pullup structure of UCC2752X output stage.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

10%

90%

Enable

Output

Low

High

Low

High

Input

tD1 tD2 UDG-11219

10%

90%

Enable

Output

Low

High

Low

High

Input

tD1 tD2 UDG-11220

10%

90%

Enable

Output

Low

High

Low

High

Input

tD3 tD4 UDG-11217

10%

90%

Enable

Output

Low

High

Low

High

Input

tD3 tD4 UDG-11218

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

7.6 Switching Characteristics

over operating free-air temperature range (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

tRRise time (1) CLOAD = 1.8 nF 7 18

tFFall time(1) CLOAD = 1.8 nF 6 10

INA = INB, OUTA and OUTB at 50%

tMDelay matching between 2 channels 1 4

transition point ns

Minimum input pulse width that

tPW 15 25

changes the output state

tD1, tD2 Input to output propagation delay (1) CLOAD = 1.8 nF, 5-V input pulse 6 13 23

tD3, tD4 EN to output propagation delay (1) CLOAD = 1.8 nF, 5-V enable pulse 6 13 23

(1) See timing diagrams in Figure 1,Figure 2,Figure 3, and Figure 4

Figure 1. Enable Function Figure 2. Enable Function

(For Non-Inverting Input Driver Operation) (For Inverting Input Driver Operation)

Figure 3. Non-Inverting Input Driver Operation Figure 4. Inverting Input Driver Operation

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

0.5

1.5

2.5

−50 0 50 100 150

Temperature (°C)

Input Threshold (V)

Input High Threshold

Input Low Threshold

VDD = 12 V

G004

0.5

1.5

2.5

−50 0 50 100 150

Temperature (°C)

Enable Threshold (V)

Enable High Threshold

Enable Low Threshold

VDD = 12 V

G005

0.2

0.3

0.4

0.5

0.6

−50 0 50 100 150

Temperature (°C)

Supply Current (mA)

Input=GND

Input=VDD

Enable=12 V

VDD = 12 V

G012

3.5

4.5

−50 0 50 100 150

Temperature (°C)

UVLO Threshold (V)

UVLO Rising

UVLO Falling

G003

0.06

0.08

0.1

0.12

0.14

−50 0 50 100 150

Temperature (°C)

Startup Current (mA)

Input=VDD

Input=GND

VDD=3.4V

G001

2.5

3.5

−50 0 50 100 150

Temperature (°C)

Operating Supply Current (mA)

VDD = 12 V

fSW = 500 kHz

CL = 500 pF

G002

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

7.7 Typical Characteristics

Figure 5. Start-Up Current vs Temperature Figure 6. Operating Supply Current vs Temperature

(Outputs Switching)

Figure 7. Supply Current vs Temperature (Outputs in DC Figure 8. UVLO Threshold vs Temperature

ON/OFF Condition)

Figure 9. Input Threshold vs Temperature Figure 10. Enable Threshold vs Temperature

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

−50 0 50 100 150

Temperature (°C)

Input to Output Propagation Delay (ns)

Turn−on

Turn−off

VDD = 12 V

CLOAD = 1.8 nF

G010

−50 0 50 100 150

Temperature (°C)

EN to Output Propagation Delay (ns)

EN to Output High

EN to Output Low

VDD = 12 V

CLOAD = 1.8 nF

G011

−50 0 50 100 150

Temperature (°C)

Rise Time (ns)

VDD = 12 V

CLOAD = 1.8 nF

G008

−50 0 50 100 150

Temperature (°C)

Fall Time (ns)

VDD = 12 V

CLOAD = 1.8 nF

G009

−50 0 50 100 150

Temperature (°C)

Output Pull−up Resistance (Ω)

VDD = 12 V

IOUT = −10 mA

G006

0.2

0.4

0.6

0.8

−50 0 50 100 150

Temperature (°C)

Output Pull−down Resistance (Ω)

VDD = 12 V

IOUT = 10 mA

G007

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Typical Characteristics (continued)

Figure 11. Output Pullup Resistance vs Temperature Figure 12. Output Pulldown Resistance vs Temperature

Figure 13. Rise Time vs Temperature Figure 14. Fall Time vs Temperature

Figure 15. Input to Output Propagation Delay vs Figure 16. EN to Output Propagation Delay vs Temperature

Temperature

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

0.5

1.5

2.5

−50 0 50 100 150

Temperature (°C)

Enable Threshold (V)

Enable High Threshold

Enable Low Threshold VDD = 4.5 V

G017

4 8 12 16 20

Supply Voltage (V)

Rise Time (ns)

CLOAD = 1.8 nF

G015

4 8 12 16 20

Supply Voltage (V)

Fall Time (ns)

CLOAD = 1.8 nF

G016

0 100 200 300 400 500 600 700 800 900 1000

Frequency (kHz)

Operating Supply Current (mA)

VDD = 4.5 V

VDD = 12 V

VDD = 15 V

CLOAD = 1.8 nF

Both channels switching

G013

4 8 12 16 20

Supply Voltage (V)

Propagation Delays (ns)

Input to Output On delay

Input to Ouptut Off Delay

EN to Output On Delay

EN to Output Off Delay

CLOAD = 1.8 nF

G014

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Typical Characteristics (continued)

Figure 17. Operating Supply Current vs Frequency Figure 18. Propagation Delays vs Supply Voltage

Figure 19. Rise Time vs Supply Voltage Figure 20. Fall Time vs Supply Voltage

Figure 21. Enable Threshold vs Temperature

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

1ENA

200 kW

VDD

INA

400 kW

3GND

INB

400 kW

UVLO

VDD

ENB

OUTA

VDD

OUTB

200 kW

VDD

1ENA

200 kW

VDD

2INA

200 kW

VDD

3GND

4INB

200 kW

VDD UVLO

VDD

ENB

OUTA

VDD

OUTB

200 kW

VDD

UDG-11221

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

8 Detailed Description

8.1 Overview

The UCC2752x family of products represent TI’s latest generation of dual-channel, low-side, high-speed gate-

driver devices featuring 5-A source and sink current capability, industry best-in-class switching characteristics

and a host of other features listed in Table 1 all of which combine to ensure efficient, robust and reliable

operation in high-frequency switching power circuits.

Table 1. UCC2752x Family of Features and Benefits

FEATURE BENEFIT

Best-in-class 13-ns (typ) propagation delay Extremely low-pulse transmission distortion

1-ns (typ) delay matching between channels Ease of paralleling outputs for higher (2 times) current capability,

ease of driving parallel-power switches

Expanded VDD Operating range of 4.5 to 18 V Flexibility in system design

Expanded operating temperature range of –40°C to 140°C

(See Electrical Characteristics)

VDD UVLO Protection Outputs are held Low in UVLO condition, which ensures predictable,

glitch-free operation at power-up and power-down

Outputs held Low when input pins (INx) in floating condition Safety feature, especially useful in passing abnormal condition tests

during safety certification

Outputs enable when enable pins (ENx) in floating condition Pin-to-pin compatibility with UCC2732X family of products from TI, in

designs where pin 1 and 8 are in floating condition

CMOS/TTL compatible input and enable threshold with wide Enhanced noise immunity, while retaining compatibility with

hysteresis microcontroller logic level input signals (3.3 V, 5 V) optimized for

digital power

Ability of input and enable pins to handle voltage levels not restricted System simplification, especially related to auxiliary bias supply

by VDD pin bias voltage architecture

8.2 Functional Block Diagrams

Figure 22. UCC27523 Block Diagram Figure 23. UCC27524 Block Diagram

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

8INA+

200 kW

VDD

1INA-

400 kW

3GND

7INB+

400 kW

UVLO

VDD

OUTA

VDD

OUTB

VDD

UDG-11222

2INB-

200 kW

VDD

1ENA

200 kW

VDD

2INA

3GND

4INB

400 kW

UVLO

VDD

ENB

OUTA

VDD

OUTB

200 kW

VDD

UDG-11223

200 kW

VDD

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Functional Block Diagrams (continued)

Figure 24. UCC27525 Block Diagram Figure 25. UCC27526 Block Diagram

8.3 Feature Description

8.3.1 VDD and Undervoltage Lockout

The UCC2752x devices have internal undervoltage-lockout (UVLO) protection feature on the VDD pin supply

circuit blocks. When VDD is rising and the level is still below UVLO threshold, this circuit holds the output LOW,

regardless of the status of the inputs. The UVLO is typically 4.2 V with 300-mV typical hysteresis. This hysteresis

prevents chatter when low VDD supply voltages have noise from the power supply and also when there are

droops in the VDD bias voltage when the system commences switching and there is a sudden increase in IDD.

The capability to operate at low voltage levels such as below 5 V, along with best-in-class switching

characteristics, is especially suited for driving emerging GaN power semiconductor devices.

For example, at power up, the UCC2752x driver-device output remains LOW until the VDD voltage reaches the

UVLO threshold if Enable pin is active or floating. The magnitude of the OUT signal rises with VDD until steady-

state VDD is reached. The non-inverting operation in Figure 26 shows that the output remains LOW until the

UVLO threshold is reached, and then the output is in-phase with the input. The inverting operation in Figure 27

shows that the output remains LOW until the UVLO threshold is reached, and then the output is out-phase with

the input. With UCC27526 the output turns to high-state only if INX+ is high and INX– is low after the UVLO

threshold is reached.

Because the device draws current from the VDD pin to bias all internal circuits, for the best high-speed circuit

performance, TI recommends two VDD bypass capacitors to prevent noise problems. TI highly recommends using

surface-mount components. A 0.1-μF ceramic capacitor must be located as close as possible to the VDD to GND

pins of the gate-driver device. In addition, a larger capacitor (such as 1-μF) with relatively low ESR must be

connected in parallel and close proximity, in order to help deliver the high-current peaks required by the load.

The parallel combination of capacitors presents a low impedance characteristic for the expected current levels

and switching frequencies in the application.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

VDD

OUT

VDD Threshold

UDG-11228

VDD

OUT

VDD Threshold

UDG-11229

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Feature Description (continued)

Figure 27. Power up Inverting Driver

Figure 26. Power up Non-Inverting Driver

8.3.2 Operating Supply Current

The UCC2752x products feature very low quiescent IDD currents. The typical operating-supply current in UVLO

state and fully on state (under static and switching conditions) are summarized in Figure 5,Figure 6 and

Figure 7. The IDD current when the device is fully on and outputs are in a static state (DC high or DC low, refer

Figure 6) represents lowest quiescent IDD current when all the internal logic circuits of the device are fully

operational. The total supply current is the sum of the quiescent IDD current, the average IOUT current due to

switching and finally any current related to pullup resistors on the enable pins and inverting input pins. For

example when the inverting Input pins are pulled low additional current is drawn from VDD supply through the

pullup resistors (refer to Figure 22 though Figure 25). Knowing the operating frequency (fSW) and the MOSFET

gate (QG) charge at the drive voltage being used, the average IOUT current can be calculated as product of QG

and fSW.

A complete characterization of the IDD current as a function of switching frequency at different VDD bias voltages

under 1.8-nF switching load in both channels is provided in Figure 17. The strikingly linear variation and close

correlation with theoretical value of average IOUT indicates negligible shoot-through inside the gate-driver device

attesting to its high-speed characteristics.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Feature Description (continued)

8.3.3 Input Stage

The input pins of UCC2752x gate-driver devices are based on a TTL and CMOS compatible input-threshold logic

that is independent of the VDD supply voltage. With typically high threshold = 2.1 V and typically low threshold =

1.2 V, the logic level thresholds are conveniently driven with PWM control signals derived from 3.3-V and 5-V

digital power-controller devices. Wider hysteresis (typ 0.9 V) offers enhanced noise immunity compared to

traditional TTL logic implementations, where the hysteresis is typically less than 0.5 V. UCC2752x devices also

feature tight control of the input pin threshold voltage levels which eases system design considerations and

ensures stable operation across temperature (refer to Figure 9). The very low input capacitance on these pins

reduces loading and increases switching speed.

The UCC2752x devices feature an important safety feature wherein, whenever any of the input pins is in a

floating condition, the output of the respective channel is held in the low state. This is achieved using VDD pullup

resistors on all the Inverting inputs (INA, INB in UCC27523, INA in UCC27525 and INA–, INB– in UCC27526) or

GND pulldown resistors on all the non-inverting input pins (INA, INB in UCC27524, INB in UCC27525 and INA+,

INB+ in UCC27526), as shown in the device block diagrams.

While UCC27523/4/5 devices feature one input pin per channel, the UCC27526 features a dual input

configuration with two input pins available to control the output state of each channel. With the UCC27526 device

the user has the flexibility to drive each channel using either a non-inverting input pin (INx+) or an inverting input

pin (INx–). The state of the output pin is dependent on the bias on both the INx+ and INx– pins (where x = A, B).

Once an Input pin is chosen to drive a channel, the other input pin of that channel (the unused input pin) must be

properly biased in order to enable the output of the channel. The unused input pin cannot remain in a floating

condition because, as mentioned earlier, whenever any input pin is left in a floating condition, the output of that

channel is disabled using the internal pullup or pulldown resistors for safety purposes. Alternatively, the unused

input pin is used effectively to implement an enable/disable function, as explained below.

• In order to drive the channel x (x = A or B) in a non-inverting configuration, apply the PWM control input

signal to INx+ pin. In this case, the unused input pin, INx-, must be biased low (for example, tied to GND) in

order to enable the output of this channel.

– Alternately, the INx– pin can be used to implement the enable/disable function using an external logic

signal. OUTx is disabled when INx- is biased High and OUTx is enabled when INX– is biased low.

• In order to drive the channel x (x = A or B) in an Inverting configuration, apply the PWM control input signal to

INX– pin. In this case, the unused input pin, INX+, must be biased high (for example, tied to VDD) in order to

enable the output of the channel.

– Alternately, the INX+ pin can be used to implement the enable/disable function using an external logic

signal. OUTX is disabled when INX+ is biased low and OUTX is enabled when INX+ is biased high.

• Finally, it is worth noting that the UCC27526 output pin can be driven into high state only when INx+ pin is

biased high and INx- input is biased low.

Refer to the input/output logic truth table and typical application diagrams, (Figure 34,Figure 35, and Figure 35),

for additional clarification.

The input stage of each driver is driven by a signal with a short rise or fall time. This condition is satisfied in

typical power supply applications, where the input signals are provided by a PWM controller or logic gates with

fast transition times (< 200 ns) with a slow changing input voltage, the output of the driver may switch repeatedly

at a high frequency. While the wide hysteresis offered in UCC2752x definitely alleviates this concern over most

other TTL input threshold devices, extra care is necessary in these implementations. If limiting the rise or fall

times to the power device is the primary goal, then TI highly recommends an external resistance between the

output of the driver and the power device. This external resistor has the additional benefit of reducing part of the

gate-charge related power dissipation in the gate-driver device package and transferring it into the external

resistor itself.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Feature Description (continued)

8.3.4 Enable Function

The enable function is an extremely beneficial feature in gate-driver devices especially for certain applications

such as synchronous rectification where the driver outputs disable in light-load conditions to prevent negative

current circulation and to improve light-load efficiency.

UCC27523/4/5 devices are provided with independent enable pins ENx for exclusive control of each driver-

channel operation. The enable pins are based on a non-inverting configuration (active-high operation). Thus

when ENx pins are driven high the drivers are enabled and when ENx pins are driven low the drivers are

disabled. Like the input pins, the enable pins are also based on a TTL and CMOS compatible input-threshold

logic that is independent of the supply voltage and are effectively controlled using logic signals from 3.3-V and 5-

V microcontrollers. The UCC2752X devices also feature tight control of the Enable-function threshold-voltage

levels which eases system design considerations and ensures stable operation across temperature (refer to

Figure 10). The ENx pins are internally pulled up to VDD using pullup resistors as a result of which the outputs of

the device are enabled in the default state. Hence the ENx pins are left floating or Not Connected (N/C) for

standard operation, where the enable feature is not needed. Essentially, this floating allows the UCC27523/4/5

devices to be pin-to-pin compatible with TI’s previous generation drivers UCC27323/4/5 respectively, where pins

1, 8 are N/C pins. If the Channel A and Channel B inputs and outputs are connected in parallel to increase the

driver current capacity, ENA and ENB are connected and driven together.

The UCC27526 device does not feature dedicated enable pins. However, as mentioned earlier, an

enable/disable function is easily implemented in UCC27526 using the unused input pin. When INx+ is pulled

down to GND or INx– is pulled down to VDD, the output is disabled. Thus INx+ pin is used like an enable pin that

is based on active high logic, while INx– is used like an enable pin that is based on active low logic. Note that

while the ENA, ENB pins in UCC27523/4/5 are allowed to be in floating condition during standard operation and

the outputs will be enabled, the INx+, INx– pins in UCC27526 are not allowed to be floating because this will

disable the outputs.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

VCC

ROH

ROL

Gate

Voltage

Boost

Narrow Pulse at

each Turn On

Anti Shoot-

Through

Circuitry

Input Signal

RNMOS, Pull Up

OUT

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Feature Description (continued)

8.3.5 Output Stage

The UCC2752x device output stage features a unique architecture on the pullup structure which delivers the

highest peak-source current when it is most needed during the Miller plateau region of the power-switch turnon

transition (when the power switch drain or collector voltage experiences dV/dt). The output stage pullup structure

features a P-channel MOSFET and an additional N-channel MOSFET in parallel. The function of the N-channel

MOSFET is to provide a brief boost in the peak sourcing current enabling fast turnon. This is accomplished by

briefly turning-on the N-channel MOSFET during a narrow instant when the output is changing state from Low to

High.

Figure 28. UCC2752x Gate Driver Output Structure

The ROH parameter (see Electrical Characteristics) is a DC measurement and it is representative of the on-

resistance of the P-Channel device only. This is because the N-Channel device is held in the off state in DC

condition and is turned-on only for a narrow instant when output changes state from low to high. Note that

effective resistance of UCC2752x pullup stage during the turnon instant is much lower than what is represented

by ROH parameter.

The pulldown structure in UCC2752x is simply composed of a N-Channel MOSFET. The ROL parameter (see

Electrical Characteristics), which is also a DC measurement, is representative of the impedance of the pulldown

stage in the device. In UCC2752x, the effective resistance of the hybrid pullup structure during turnon is

estimated to be approximately 1.5 × ROL, estimated based on design considerations.

Each output stage in UCC2752x can supply 5-A peak source and 5-A peak sink current pulses. The output

voltage swings between VDD and GND providing rail-to-rail operation, thanks to the MOS-output stage which

delivers very low drop-out. The presence of the MOSFET-body diodes also offers low impedance to switching

overshoots and undershoots which means that in many cases, external Schottky-diode clamps may be

eliminated. The outputs of these drivers are designed to withstand 500-mA reverse current without either

damage to the device or logic malfunction.

The UCC2752x devices are particularly suited for dual-polarity, symmetrical drive-gate transformer applications

where the primary winding of transformer driven by OUTA and OUTB, with inputs INA and INB being driven

complementary to each other. This situation is due to the extremely low drop-out offered by the MOS output

stage of these devices, both during high (VOH) and low (VOL) states along with the low impedance of the driver

output stage, all of which allow alleviate concerns regarding transformer demagnetization and flux imbalance.

The low propagation delays also ensure accurate reset for high-frequency applications.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

1ENA

200 kW

VDD

INA

400 kW

3GND

INB

400 kW

UVLO

VDD

ENB

OUTA

VDD

OUTB

200 kW

VDD

ISHOOT-THROUGH

VIN_H

(Channel B)

VIN_H

(Channel A)

Slow Input Signal

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Feature Description (continued)

For applications that have zero voltage switching during power MOSFET turnon or turnoff interval, the driver

supplies high-peak current for fast switching even though the miller plateau is not present. This situation often

occurs in synchronous rectifier applications because the body diode is generally conducting before power

MOSFET is switched on.

8.3.6 Low Propagation Delays and Tightly Matched Outputs

The UCC2752x driver devices feature a best in class, 13-ns (typical) propagation delay between input and output

which goes to offer the lowest level of pulse-transmission distortion available in the industry for high frequency

switching applications. For example in synchronous rectifier applications, the SR MOSFETs are driven with very

low distortion when one driver device is used to drive both the SR MOSFETs. Further, the driver devices also

feature an extremely accurate, 1-ns (typ) matched internal-propagation delays between the two channels which

is beneficial for applications requiring dual gate drives with critical timing. For example in a PFC application, a

pair of paralleled MOSFETs may be driven independently using each output channel, which the inputs of both

channels are driven by a common control signal from the PFC controller device. In this case the 1ns delay

matching ensures that the paralleled MOSFETs are driven in a simultaneous fashion with the minimum of turnon

delay difference. Yet another benefit of the tight matching between the two channels is that the two channels are

connected together to effectively increase current drive capability, for example A and B channels may be

combined into one driver by connecting the INA and INB inputs together and the OUTA and OUTB outputs

together. Then, one signal controls the paralleled combination.

Caution must be exercised when directly connecting OUTA and OUTB pins together because there is the

possibility that any delay between the two channels during turnon or turnoff may result in shoot-through current

conduction as shown in Figure 29. While the two channels are inherently very well matched (4-ns Max

propagation delay), note that there may be differences in the input threshold voltage level between the two

channels which causes the delay between the two outputs especially when slow dV/dt input signals are

employed. TI recommends the following guidelines whenever the two driver channels are paralleled using direct

connections between OUTA and OUTB along with INA and INB:

• Use very fast dV/dt input signals (20 V/µs or greater) on INA and INB pins to minimize impact of differences

in input thresholds causing delays between the channels.

• INA and INB connections must be made as close to the device pins as possible.

Wherever possible, a safe practice would be to add an option in the design to have gate resistors in series with

OUTA and OUTB. This allows the option to use 0-Ωresistors for paralleling outputs directly or to add appropriate

series resistances to limit shoot-through current, should it become necessary.

Figure 29. Slow Input Signal May Cause Shoot-Through Between Channels During Paralleling

(Recommended dV/dT is 20 V/Μs or Higher)

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Feature Description (continued)

Figure 30. Turnon Propagation Delay Figure 31. Turnon Rise Time

(CL= 1.8 nF, VDD = 12 V) (CL= 1.8 nF, VDD = 12 V)

Figure 32. Turnoff Propagation Delay Figure 33. Turnoff Fall Time

(CL= 1.8 nF, VDD = 12 V) (CL= 1.8 nF, VDD = 12 V)

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

8.4 Device Functional Modes

Table 2. Device Logic Table (UCC27523/4/5)

UCC27523/4/5 UCC27523 UCC27524 UCC27525

ENA ENB INA INB OUTA OUTB OUTA OUTB OUTA OUTB

H H L L H H L L H L

H H L H H L L H H H

H H H L L H H L L L

H H H H L L H H L H

L L Any Any L L L L L L

Any Any x(1) x(1) LLLLLL

x(1) x(1) L L H H L L H L

x(1) x(1) L H H L L H H H

x(1) x(1) H L L H H L L L

x(1) x(1) H H L L H H L H

(1) Floating condition.

Table 3. Device Logic Table (UCC27526)

INx+ (x = A or B) INx- (x = A or B) OUTx (x = A or B)

LLL

L H L

H L H

H H L

x(1) Any L

Any x(1) L

(1) x = Floating condition.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

ENA

INA

GND

INB

ENB

OUTA

VDD

OUTB

UCC2752x

GND

V+

INB

INA

ENA

ENB

UDG-11225

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

High-current gate-driver devices are required in switching power applications for a variety of reasons. In order to

effect fast switching of power devices and reduce associated switching-power losses, a powerful gate-driver

device employs between the PWM output of control devices and the gates of the power semiconductor devices.

Further, gate-driver devices are indispensable when having the PWM controller device directly drive the gates of

the switching devices is sometimes not feasible. With advent of digital power, this situation is often encountered

because the PWM signal from the digital controller is often a 3.3-V logic signal which cannot effectively turn on a

power switch. A level-shifting circuitry is needed to boost the 3.3-V signal to the gate-drive voltage (such as 12 V)

in order to fully turn on the power device and minimize conduction losses. Traditional buffer-drive circuits based

on NPN/PNP bipolar transistors in totem-pole arrangement, being emitter-follower configurations, prove

inadequate with digital power because they lack level-shifting capability. Gate-driver devices effectively combine

both the level-shifting and buffer-drive functions. Gate-driver devices also find other needs such as minimizing

the effect of high-frequency switching noise by locating the high-current driver physically close to the power

switch, driving gate-drive transformers and controlling floating power-device gates, reducing power dissipation

and thermal stress in controller devices by moving gate-charge power losses into the controller.

Finally, emerging wide band-gap power-device technologies such as GaN based switches, which can support

very high switching frequency operation, are driving special requirements in terms of gate-drive capability. These

requirements include operation at low VDD voltages (5 V or lower), low propagation delays, tight delay matching

and availability in compact, low-inductance packages with good thermal capability.

In summary gate-driver devices are extremely important components in switching power combining benefits of

high-performance, low-cost, component-count, board-space reduction, and simplified system design.

9.2 Typical Application

Figure 34. UCC2752x Typical Application Diagram (x = 3, 4, or 5)

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

INA-

INB-

GND

OUTB

INA+

INB+

OUTA

VDD

UCC27526

GND

V+

INA-

INB+

ENA

ENB

OUTB is

ENABLED when

ENB is LOW

OUTA is

ENABLED when

ENA is HIGH

UDG-11227

INA-

INB-

GND

OUTB

INA+

INB+

OUTA

VDD

UCC27526

GND

V+

INA-

INB+

UDG-11226

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Typical Application (continued)

Figure 35. UCC27526 Channel A in Inverting and Channel B in Non-Inverting Configuration (Enable

Function Not Used)

Figure 36. UCC27526 Channel A in Inverting and Channel B in Non-Inverting Configuration (Enable

Function Implemented)

9.2.1 Design Requirements

When selecting the proper gate-driver device for an end application, some design considerations must be

evaluated first in order to make the most appropriate selection. Among these considerations are input-to-output

logic, VDD, UVLO, Drive current and power dissipation.

9.2.2 Detailed Design Procedure

9.2.2.1 Input-to-Output Logic

The design should specify which type of input-to-output configuration should be used. The UCC27523 device can

provide dual inverting input to output with enable control. The UCC27524 device can provide dual non-inverting

input to output with enable control. The UCC27525 device can provide one inverting and one non-inverting input

to output control. If turning on the power MOSFET or IGBT when the input signal is in high state is preferred,

then the non-inverting configuration must be selected. If turning off the power MOSFET or IGBT when the input

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Typical Application (continued)

signal is in high state is preferred, the inverting configuration must be chosen. UCC27526 has dual configuration

channel. Each Channel of UCC27526 device can be configured in either an inverting or non-inverting input-to-

output configuration using the INx– or INx+ pins respectively like in Figure 35 and Figure 36. To configure the

channel for use in inverting mode, tie the INx+ pin to VDD and apply the input signal to the INx– pin. For the non-

inverting configuration, tie the INx– pin to GND and apply the input signal to the INx+ pin.

9.2.2.2 Enable and Disable Function

Certain applications demand independent control of the output state of the driver. The UCC27523/4/5 device

offers two independent enable pins ENx for exclusive control of each driver channels as listed in Table 2.

The UCC27526 device does not feature dedicated enable pins. However, as mentioned earlier, an

enable/disable function can be easily implemented in UCC27526 using the unused input pin. When INx+ is

pulled-down to GND or INx– is pulled-down to VDD, the output is disabled as listed in Table 3. Thus INx+ pin can

be used like an enable pin that is based on active high logic, while INx– can be used like an enable pin that is

based on active low logic. It is important to note that while the ENA, ENB pins in the UCC27523/4/5 are allowed

to be in floating condition during standard operation and the outputs will be enabled, the INx+, INx– pins in

UCC27526 are not allowed to be floating because this will disable the outputs.

9.2.2.3 VDD Bias Supply Voltage

The bias supply voltage to be applied to the VDD pin of the device should never exceed the values listed in the

Recommended Operating Conditions. However, different power switches demand different voltage levels to be

applied at the gate terminals for effective turnon and turnoff. With certain power switches, a positive gate voltage

may be required for turnon and a negative gate voltage may be required for turnoff, in which case the VDD bias

supply equals the voltage differential. With a wide operating range from 4.5 V to 18 V, the UCC2752x device can

be used to drive a variety of power switches, such as Si MOSFETs (for example, VGS = 4.5 V, 10 V, 12 V),

IGBTs (VGE = 15 V, 18 V).

9.2.2.4 Propagation Delay

The acceptable propagation delay from the gate driver is dependent on the switching frequency at which it is

used and the acceptable level of pulse distortion to the system. The UCC2752x device features fast 13-ns

(typical) propagation delays which ensures very little pulse distortion and allows operation at very high-

frequencies. See the Switching Characteristics for the propagation and switching characteristics of the

UCC2752x device.

9.2.2.5 Drive Current and Power Dissipation

The UCC27523/4/5/6 family of drivers are capable of delivering 5-A of current to a MOSFET gate for a period of

several-hundred nanoseconds at VDD = 12 V. High peak current is required to turn the device ON quickly. Then,

to turn the device OFF, the driver is required to sink a similar amount of current to ground which repeats at the

operating frequency of the power device. The power dissipated in the gate-driver device package depends on the

following factors:

• Gate charge required of the power MOSFET (usually a function of the drive voltage VGS, which is very close

to input bias supply voltage VDD due to low VOH drop-out)

• Switching frequency

• Use of external gate resistors

Because UCC2752x features very low quiescent currents and internal logic to eliminate any shoot-through in the

output driver stage, their effect on the power dissipation within the gate driver can be safely assumed to be

negligible.

When a driver device is tested with a discrete, capacitive load calculating the power that is required from the bias

supply is fairly simple. The energy that must be transferred from the bias supply to charge the capacitor is given

by Equation 1.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

P 0.6 mA 12 V 7.2mW= ´ =

Q DD DD

P I V=

OFF ON

SW G SW

OFF GATE ON GATE

R R

P 0.5 Q VDD f

R R R R

æ ö

= ´ ´ ´ ´ +

ç ÷

+ +

è ø

P 2 x 60nC 12 V 300 kHz 0.432 W= ´ ´ =

G LOAD DD SW g DD SW

P C V f Q V f= =

P 10 nF 12 V 300 kHz 0.432 W= ´ ´ =

G LOAD DD SW

P C V f=

G LOAD DD

E C V

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Typical Application (continued)

where

• CLOAD is load capacitor

• VDD is bias voltage feeding the driver. (1)

There is an equal amount of energy dissipated when the capacitor is charged. This leads to a total power loss

given by Equation 2.

where

• fSW is the switching frequency (2)

With VDD = 12 V, CLOAD = 10 nF and ƒSW = 300 kHz the power loss is calculated as (see Equation 3):

(3)

The switching load presented by a power MOSFET is converted to an equivalent capacitance by examining the

gate charge required to switch the device. This gate charge includes the effects of the input capacitance plus the

added charge needed to swing the drain voltage of the power device as it switches between the ON and OFF

states. Most manufacturers provide specifications that provide the typical and maximum gate charge, in nC, to

switch the device under specified conditions. Using the gate charge Qg, the power that must be dissipated when

charging a capacitor is determined which by using the equivalence Qg= CLOADVDD to provide Equation 4 for

power:

(4)

Assuming that UCC2752x is driving power MOSFET with 60 nC of gate charge (Qg= 60 nC at VDD = 12 V) on

each output, the gate charge related power loss is calculated as (see Equation 5):

(5)

This power PG is dissipated in the resistive elements of the circuit when the MOSFET turns on or turns off. Half

of the total power is dissipated when the load capacitor is charged during turnon, and the other half is dissipated

when the load capacitor is discharged during turnoff. When no external gate resistor is employed between the

driver and MOSFET/IGBT, this power is completely dissipated inside the driver package. With the use of external

gate drive resistors, the power dissipation is shared between the internal resistance of driver and external gate

resistor in accordance to the ratio of the resistances (more power dissipated in the higher resistance component).

Based on this simplified analysis, the driver power dissipation during switching is calculated as follows (see

Equation 6):

where

• ROFF = ROL

• RON (effective resistance of pullup structure) = 1.5 x ROL (6)

In addition to the above gate-charge related power dissipation, additional dissipation in the driver is related to the

power associated with the quiescent bias current consumed by the device to bias all internal circuits such as

input stage (with pullup and pulldown resistors), enable, and UVLO sections. As shown in Figure 6, the quiescent

current is less than 0.6 mA even in the highest case. The quiescent power dissipation is calculated easily with

Equation 7.

(7)

Assuming , IDD = 6 mA, the power loss is:

(8)

Clearly, this power loss is insignificant compared to gate charge related power dissipation calculated earlier.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

P0.432 W

I ~ 0.036 A

V 12 V

= =

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Typical Application (continued)

With a 12-V supply, the bias current is estimated as follows, with an additional 0.6-mA overhead for the

quiescent consumption:

(9)

9.2.3 Application Curves

Figure 37 and Figure 38 show the typical switching characteristics of the non-inverting input driver operation for

UCC27523/4/5/6 device. CL= 1.8 nF, VDD = 12 V

Figure 37. Typical Turnon Waveform Figure 38. Typical Turnoff Waveform

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

10 Power Supply Recommendations

The bias supply voltage range for which the UCC2752X device is rated to operate is from 4.5 V to 18 V. The

lower end of this range is governed by the internal undervoltage-lockout (UVLO) protection feature on the VDD

pin supply circuit blocks. Whenever the driver is in UVLO condition when the VDD pin voltage is below the VON

supply start threshold, this feature holds the output low, regardless of the status of the inputs. The upper end of

this range is driven by the 20-V absolute maximum voltage rating of the VDD pin of the device (which is a stress

rating). Keeping a 2-V margin to allow for transient voltage spikes, the maximum recommended voltage for the

VDD pin is 18 V.

The UVLO protection feature also involves a hysteresis function. This means that when the VDD pin bias voltage

has exceeded the threshold voltage, device begins to operate, and if the voltage drops, then the device

continues to deliver normal functionality unless the voltage drop exceeds the hysteresis specification VDD_H.

Therefore, ensuring that, while operating at or near the 4.2-V range, the voltage ripple on the auxiliary power

supply output is smaller than the hysteresis specification of the device is important to avoid triggering device

shutdown. During system shutdown, the device operation continues until the VDD pin voltage has dropped below

the VOFF threshold which must be accounted for while evaluating system shutdown timing design requirements.

Likewise, at system startup, the device does not begin operation until the VDD pin voltage has exceeded above

the VON threshold. The quiescent current consumed by the internal circuit blocks of the device is supplied

through the VDD pin. It is important to recognize that the charge for source current pulses delivered by the

OUTA/B pin is also supplied through the same VDD pin. As a result, every time a current is sourced out of the

output pins, a corresponding current pulse is delivered into the device through the VDD pin. Thus ensuring that

local bypass capacitors are provided between the VDD and GND pins and located as close to the device as

possible for the purpose of decoupling is important. A low ESR, ceramic surface mount capacitor is a must. TI

recommends having two capacitors; a 100-nF ceramic surface-mount capacitor which can be nudged very close

to the pins of the device and another surface-mount capacitor of few microfarads added in parallel.

11 Layout

11.1 Layout Guidelines

Proper PCB layout is extremely important in a high-current fast-switching circuit to provide appropriate device

operation and design robustness. The UCC27523/4/5/6 family of gate drivers incorporates short propagation

delays and powerful output stages capable of delivering large current peaks with very fast rise and fall times at

the gate of power MOSFET to facilitate voltage transitions very quickly. At higher VDD voltages, the peak current

capability is even higher (5-A peak current is at VDD = 12 V). Very high di/dt causes unacceptable ringing if the

trace lengths and impedances are not well controlled. TI strongly recommends the following circuit layout

guidelines when designing with these high-speed drivers.

• Locate the driver device as close as possible to power device in order to minimize the length of high-current

traces between the Output pins and the Gate of the power device.

• Locate the VDD bypass capacitors between VDD and GND as close as possible to the driver with minimal trace

length to improve the noise filtering. These capacitors support high peak current being drawn from VDD during

turnon of power MOSFET. The use of low inductance SMD components such as chip resistors and chip

capacitors is highly recommended.

• The turnon and turnoff current loop paths (driver device, power MOSFET and VDD bypass capacitor) should

be minimized as much as possible in order to keep the stray inductance to a minimum. High dI/dt is

established in these loops at 2 instances during turnon and turnoff transients, which will induce significant

voltage transients on the output pin of the driver device and Gate of the power MOSFET.

• Wherever possible, parallel the source and return traces, taking advantage of flux cancellation

• Separate power traces and signal traces, such as output and input signals.

• Star-point grounding is a good way to minimize noise coupling from one current loop to another. The GND of

the driver is connected to the other circuit nodes such as source of power MOSFET and ground of PWM

controller at one, single point. The connected paths must be as short as possible to reduce inductance and

be as wide as possible to reduce resistance.

• Use a ground plane to provide noise shielding. Fast rise and fall times at OUT may corrupt the input signals

during transition. The ground plane must not be a conduction path for any current loop. Instead the ground

plane must be connected to the star-point with one single trace to establish the ground potential. In addition

to noise shielding, the ground plane can help in power dissipation as well

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

Layout Guidelines (continued)

• In noisy environments, tying inputs of an unused channel of UCC27526 to VDD (in case of INx+) or GND (in

case of INX–) using short traces in order to ensure that the output is enabled and to prevent noise from

causing malfunction in the output may be necessary.

• Exercise caution when replacing the UCC2732x/UCC2742x devices with the UCC2752x:

– UCC2752x is a much stronger gate driver (5-A peak current versus 4-A peak current).

– UCC2752x is a much faster gate driver (13-ns/13-ns rise/fall propagation delay versus 25-ns/35-ns rise/fall

propagation delay).

11.2 Layout Example

Figure 39. Layout Example for UCC27523/4/5 (D, DGN)

11.3 Thermal Considerations

The useful range of a driver is greatly affected by the drive power requirements of the load and the thermal

characteristics of the device package. In order for a gate-driver device to be useful over a particular temperature

range the package must allow for the efficient removal of the heat produced while keeping the junction

temperature within rated limits. The UCC27523/4/5/6 family of drivers is available in four different packages to

cover a range of application requirements. The thermal metrics for each of these packages are summarized in

Thermal Information. For detailed information regarding the thermal information table, refer to Application Note

from Texas Instruments entitled, IC Package Thermal Metrics (SPRA953).

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

www.ti.com

Thermal Considerations (continued)

Among the different package options available in the UCC2752x family, of particular mention are the DSD and

DGN packages when it comes to power dissipation capability. The MSOP PowerPAD-8 (DGN) package and 3-

mm × 3-mm WSON (DSD) package offer a means of removing the heat from the semiconductor junction through

the bottom of the package. Both these packages offer an exposed thermal pad at the base of the package. This

pad is soldered to the copper on the printed-circuit-board directly underneath the device package, reducing the

thermal resistance to a very low value. This allows a significant improvement in heat-sinking over that available in

the D or P packages. The printed-circuit-board must be designed with thermal lands and thermal vias to

complete the heat removal subsystem. Note that the exposed pads in the MSOP-8 (PowerPAD) and WSON-8

packages are not directly connected to any leads of the package, however, it is electrically and thermally

connected to the substrate of the device which is the ground of the device. TI recommends to externally connect

the exposed pads to GND in PCB layout for better EMI immunity.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

UCC27523

UCC27524

UCC27525

UCC27526

www.ti.com

SLUSAQ3G –NOVEMBER 2011–REVISED APRIL 2015

12 Device and Documentation Support

12.1 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 4. Related Links

TECHNICAL TOOLS & SUPPORT &

PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY

UCC27523 Click here Click here Click here Click here Click here

UCC27524 Click here Click here Click here Click here Click here

UCC27525 Click here Click here Click here Click here Click here

UCC27526 Click here Click here Click here Click here Click here

12.2 Trademarks

PowerPAD is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.3 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12.4 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

Product Folder Links: UCC27523 UCC27524 UCC27525 UCC27526

PACKAGE OPTION ADDENDUM

www.ti.com 16-Oct-2013

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

UCC27523D ACTIVE SOIC D 8 75 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27523

UCC27523DGN ACTIVE MSOP-

PowerPAD DGN 8 80 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27523

UCC27523DGNR ACTIVE MSOP-

PowerPAD DGN 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27523

UCC27523DR ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27523

UCC27523DSDR ACTIVE SON DSD 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 27523

UCC27523DSDT ACTIVE SON DSD 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 27523

UCC27524D ACTIVE SOIC D 8 75 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27524

UCC27524DGN ACTIVE MSOP-

PowerPAD DGN 8 80 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27524

UCC27524DGNR ACTIVE MSOP-

PowerPAD DGN 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27524

UCC27524DR ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27524

UCC27524DSDR ACTIVE SON DSD 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 SBA

UCC27524DSDT ACTIVE SON DSD 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 SBA

UCC27524P ACTIVE PDIP P 8 50 Green (RoHS

& no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 140 27524

UCC27525D ACTIVE SOIC D 8 75 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27525

UCC27525DGN ACTIVE MSOP-

PowerPAD DGN 8 80 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27525

UCC27525DGNR ACTIVE MSOP-

PowerPAD DGN 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 140 27525

UCC27525DR ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 140 27525

PACKAGE OPTION ADDENDUM

www.ti.com 16-Oct-2013

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

UCC27525DSDR ACTIVE SON DSD 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 27525

UCC27525DSDT ACTIVE SON DSD 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 27525

UCC27526DSDR ACTIVE SON DSD 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 SCB

UCC27526DSDT ACTIVE SON DSD 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 140 SCB

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

PACKAGE OPTION ADDENDUM

www.ti.com 16-Oct-2013

Addendum-Page 3

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

UCC27523DGNR MSOP-

Power

PAD

DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

UCC27523DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

UCC27523DSDR SON DSD 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27523DSDT SON DSD 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27524DGNR MSOP-

Power

PAD

DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

UCC27524DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

UCC27524DSDR SON DSD 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27524DSDT SON DSD 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27525DGNR MSOP-

Power

PAD

DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

UCC27525DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

UCC27525DSDR SON DSD 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27525DSDT SON DSD 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27526DSDR SON DSD 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

UCC27526DSDT SON DSD 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2

PACKAGE MATERIALS INFORMATION

www.ti.com 9-Dec-2017

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

UCC27523DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0

UCC27523DR SOIC D 8 2500 367.0 367.0 35.0

UCC27523DSDR SON DSD 8 3000 367.0 367.0 35.0

UCC27523DSDT SON DSD 8 250 210.0 185.0 35.0

UCC27524DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0

UCC27524DR SOIC D 8 2500 367.0 367.0 35.0

UCC27524DSDR SON DSD 8 3000 367.0 367.0 35.0

UCC27524DSDT SON DSD 8 250 210.0 185.0 35.0

UCC27525DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0

UCC27525DR SOIC D 8 2500 367.0 367.0 35.0

UCC27525DSDR SON DSD 8 3000 367.0 367.0 35.0

UCC27525DSDT SON DSD 8 250 210.0 185.0 35.0

UCC27526DSDR SON DSD 8 3000 367.0 367.0 35.0

UCC27526DSDT SON DSD 8 250 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 9-Dec-2017

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

UCC27524D UCC27524DR UCC27524P UCC27524DGNR UCC27524DSDR UCC27524DSDT UCC27524DGN