S6020LV - Teccor Electronics, Inc.

Selected Packages*

U.L. RECOGNIZED

File #E71639

TO-92 TO-218AC

TO-202AB

TO-218X THERMOTAB

TO-220AB

Teccor Elec tronics, Inc. 6-1 SCRs

(972) 580-7777

SCRs

(1 – 70 Amps)

General Des cription

The Teccor Electronics line of thyristor SCR semi-conductors are

half-wave, unidirectional, gate -controlled recti fiers whic h com p le-

ment Teccor's line of sensitive SCRs. Teccor offers devices w ith

ratings of 1-70 amps and 50-800 volt s, wit h gate sensi tivities

from 10-50 m illia mps. If gate curre nts in the 12-500 micr oamp

ran ges are require d, plea se consult Tec cor's sensi tive SCR tech-

nical data sheets.

Elec tr i cally Isol ated Pack ag es

Teccor's SCRs are av ailable in a choi ce of nine different devi ce

packages. Four (of the eight) pac kages are offer ed in electrically

isolat ed construc tion where the case or tab i s inter nally isol ated

to all ow the use of low-cost assem bly and c onvenient p ackaging

techniques.

The Teccor line of SCRs featu res gla ss passivat ed device j unc-

tions to ensure long term device reliability and parameter stab il-

ity. Teccor' s glass offe rs a rugged, reliable bar rier against

juncti on contamination.

Variat ions of devic es covered in this data sheet are a vailabl e for

custom design a pplications. Please consul t the factor y for more

information.

Features

• Electrically-isolat ed package

• High voltage capabilit y — 50 up to 800 Volts

• High surge capability — up to 950 Amps

• Glass passivated chip

Electrical Specifications

SCRs 6-2 Teccor Electronics, Inc.

(972) 580-7777

General Note s

• All measurements are made at 60Hz with a resist ive load at an

ambient temperature of +25°C unless ot herwise specified.

• Operating temperature range (TJ) is -65°C to +125°C for TO-92

devices and -40°C to +125°C for all other packages.

• Storage temperature range (TS) is -65°C to +150°C for TO-92

dev ice s, - 40°C to +150 °C for TO-202 and TO-220 devices, -40°C to

+125°C for all others.

• Lead solder temperature is a maximum of 230 °C for 10 seconds

maximum; 1/16" (1.59mm) from ca se.

• The case t empera ture (TC) is measured as shown on dimensional

outline drawings. See “Package Dimensions” section of this

catalog.

Electrica l Specification Notes

(1) See Fig ures 6. 5 thr ough 6.16 for current rating at specifi ed opera t-

ing case temperature.

(2) See Figures 6 .1 and 6.2 fo r free air current rating.

(3) See Figures 6.19 and 6.20 for instantaneous on-state current vs

on-state voltage (typical).

(4) See Figure 6.18 for IGT vs TC.

(5) See Figure 6.17 for IH vs TC.

(6) For mo re than one full cycl e rating, see Fig ure 6.23.

(7) See Figure 6.22 for tgt vs IGT.

(8) See Figure 6.21 for VGT vs TC.

(9) Test condit ions ar e as foll ows: IT = 1A for 1.0A device s and 2A for

all other devices. Pulse duration = 50µs, dv/dt = 20V/µs, di/dt =

-10A/µs for 1. 0A devices, and -30A/µS for other devices.

IGT = 200mA at turn-on.

(10) See Figures 6.5 through 6.10 for maximum al lowab le case tem-

peratures at maximum rated current.

(11) Pulse width ≤ 10µs.

(12) Initial o n-state current = 200mA(D C) for 1A through 16A de vices;

400mA(DC) for 20A through 70A devices.

(13) TC = TJ for test conditions in off-state.

TYPE

Part Number IT

VDRM

& VRRM IGT IDRM & IRRM VTM VGT

Isolated Non-Isolated

TO - 92 TO - 220AB TO - 202AB TO -220AB

Maximum

On-State

Current

(1) (2)

Amps

Repetitive

Peak

Off-State

Forward

& Reverse

Voltage

Volts

DC Gate

Trigger

Current

VD = 12VDC

RL = 60Ω

(4)

mAmps

Peak Off-State

Forward & Reverse

Current at

VDRM & VRRM

(13)

mAmps

Peak

On-State

Voltage at

Max Rated

RMS

Current

TC = 25°C

(3)

Volts

DC Gate-

Trigger

Voltage

VD = 12VDC

RL = 60Ω

(8)

Volts

See “Package Dimensions” section for variations. IT(RMS) IT(AV) TC =

25°C TC =

100°C TC =

125°C TC =

25°C TC =

125°C

MAX MAX MIN MIN MAX MAX MAX MAX MIN

1.0

Amp

S051E 1.0 0.64 50 110 .01 0.2 0.5 1.6 1.5 0.2

S101E 1.0 0.64 100 110 .01 0.2 0.5 1.6 1.5 0.2

S201E 1.0 0.64 200 110 .01 0.2 0.5 1.6 1.5 0.2

S401E 1.0 0.64 400 110 .01 0.2 0.5 1.6 1.5 0.2

S601E 1.0 0.64 600 110 .01 0.2 0.5 1.6 1.5 0.2

6.0

Amps

S0506L S0506F1 6.0 3.8 50 1 15 .01 0.2 0.5 1.6 1.5 0.2

S1006L S1006F1 6.0 3.8 100 1 15 .01 0.2 0.5 1.6 1.5 0.2

S2006L S2006F1 6.0 3.8 200 1 15 .01 0.2 0.5 1.6 1.5 0.2

S4006L S4006F1 6.0 3.8 400 1 15 .01 0.2 0.5 1.6 1.5 0.2

S6006L S6006F1 6.0 3.8 600 1 15 .01 0.2 0.5 1.6 1.5 0.2

S8006L 6.0 3.8 800 1 15 .01 0.2 0.5 1.6 1.5 0.2

8.0

Amps

S0508L S0508F1 S0508R 8.0 5.1 50 115 .01 0.2 0.5 1.6 1.5 0.2

S1008L S1008F1 S1008R 8.0 5.1 100 115 .01 0.2 0.5 1.6 1.5 0.2

S2008L S2008F1 S2008R 8.0 5.1 200 115 .01 0.2 0.5 1.6 1.5 0.2

S4008L S4008F1 S4008R 8.0 5.1 400 115 .01 0.2 0.5 1.6 1.5 0.2

S6008L S6008F1 S6008R 8.0 5.1 600 115 .01 0.2 0.5 1.6 1.5 0.2

S8008L S8008R 8.0 5.1 800 115 .01 0.2 0.5 1.6 1.5 0.2

KGA

KAG

SCRs

Teccor Elec tronics, Inc. 6-3 SCRs

(972) 580-7777

IHIGM PGM PG(AV) ITSM dv/dt I2tdi/dt tgt tq

DC Holding

Current

Gate Open

(5) (12)

mAmps

Peak Gate

Current

(11)

Amps

Peak Gate

Power

Dissipation

(11)

Watts

Average

Gate Power

Dissipation

Watts

Peak One

Cycle Surge

Forward

Current

(6) (10)

Amps

Critical Rate

of Applied

Forward

Voltage

Volts/µS

RMS Surge

(Non-Repetitive)

On-State

Current

for a Period

of 8.3 ms

for Fusing

Amps2Sec

Maximum

Rate-of-Rise

of On-State

Current

IGT = 150mA

with 0.1µs

Rise Time

Amps/µSec

Gate Contr olled

Turn-On Time

Gate Pulse

= 100mA

Minimum Width=15µS

with Rise

Time ≤ 0.1µS

(7)

µSec

Circuit

Commutated

Turn-Off

Time

(9) (10)

µSec60Hz 50Hz TC =

100°C TC =

125°C

MAX MIN MIN TYP MAX

30 1.5 15 0.3 30 25 40 30 3.7 50 2.0 35

30 1.5 15 0.3 30 25 40 20 3.7 50 2.0 35

30 2.0 20 0.5 100 83 350 250 41 100 2.0 35

30 2.0 20 0.5 100 83 300 225 41 100 2.0 35

30 2.0 20 0.5 100 83 250 200 41 100 2.0 35

30 2.0 20 0.5 100 83 350 250 41 100 2.0 35

30 2.0 20 0.5 100 83 300 225 41 100 2.0 35

30 2.0 20 0.5 100 83 250 200 41 100 2.0 35

Electrical Specifications

SCRs 6-4 Teccor Electronics, Inc.

(972) 580-7777

General Note s

• All measurements are made at 60Hz with a resist ive load at an

ambient temperature of +25°C unless ot herwise specified.

• Operating temperature range (TJ) is -65°C to +125°C for TO-92

devices and -40°C to +125°C for all other packages.

• Storage temperature range (TS) is -65°C to +150°C for TO-92

dev ice s, - 40°C to +150 °C for TO-202 and TO-220 devices, -40°C to

+125°C for all others.

• Lead solder temperature is a maximum of 230 °C for 10 seconds

maximum; 1/16" (1.59mm) from ca se.

• The case t empera ture (TC) is measured as shown on dimensional

outline drawings. See “Package Dimensions” section of this

catalog.

TYPE

Part Number IT

VDRM

& VRRM IGT IDRM & IRRM VTM VGT

Isolated Non-Isolated

TO-220AB TO-202AB TO-220AB

Maximum

On-State

Current

(1)

Amps

Repetitive

Peak

Off-State

Forward

and

Reverse

Voltage

Volts

DC Gate

Trigger

Current

VD = 12VD C

RL = 60Ω

(4)

mAmps

Peak Off-State

Forward and

Reverse Current

at VDRM & VRRM

(13)

mAmps

Peak

On-State

Voltage at

Max Rated

RMS

Current

TC = 25°C

(3)

Volts

DC Gate

Trigger

Voltage

VD = 12VDC

RL = 60Ω

(8)

Volts

IT(RMS) IT(AV)

TC =

25°C TC =

100°C TC =

125°C TC =

25°C TC =

125°C

See “Package Dimensions” section for variations. MAX MAX MIN MIN MAX MAX MAX MAX MIN

10.0

Amps

S0510L S0510F1 10 6.4 50 115 .01 0.2 0.5 1.6 1.5 0.2

S1010L S1010F1 10 6.4 100 115 .01 0.2 0.5 1.6 1.5 0.2

S2010L S2010F1 10 6.4 200 115 .01 0.2 0.5 1.6 1.5 0.2

S4010L S4010F1 10 6.4 400 115 .01 0.2 0.5 1.6 1.5 0.2

S6010L S6010F1 10 6.4 600 115 .01 0.2 0.5 1.6 1.5 0.2

S8010L 10 6.4 800 115 .02 0.5 1.0 1.6 1.5 0.2

S0510R 10 6.4 50 115 .01 0.2 1.0 1.6 1.5 0.2

S1010R 10 6.4 100 115 .01 0.2 1.0 1.6 1.5 0.2

S2010R 10 6.4 200 115 .01 0.2 1.0 1.6 1.5 0.2

S4010R 10 6.4 400 115 .01 0.2 1.0 1.6 1.5 0.2

S6010R 10 6.4 600 115 .01 0.2 1.0 1.6 1.5 0.2

S8010R 10 6.4 800 115 .02 0.5 1.0 1.6 1.5 0.2

12.0

Amps

S0512R 12 7.6 50 1 20 .01 0.5 1.0 1.6 1.5 0.2

S1012R 12 7.6 100 1 20 .01 0.5 1.0 1.6 1.5 0.2

S2012R 12 7.6 200 1 20 .01 0.5 1.0 1.6 1.5 0.2

S4012R 12 7.6 400 1 20 .01 0.5 1.0 1.6 1.5 0.2

S6012R 12 7.6 600 1 20 .01 0.5 1.0 1.6 1.5 0.2

S8012R 12 7.6 800 1 20 .02 0.5 1.0 1.6 1.5 0.2

15.0

Amps

S0515L 15 9.5 50 130 .01 0.5 1.0 1.6 1.5 0.2

S1015L 15 9.5 100 130 .01 0.5 1.0 1.6 1.5 0.2

S2015L 15 9.5 200 130 .01 0.5 1.0 1.6 1.5 0.2

S4015L 15 9.5 400 130 .01 0.5 1.0 1.6 1.5 0.2

S6015L 15 9.5 600 130 .01 0.5 1.0 1.6 1.5 0.2

S8015L 15 9.5 800 130 .02 1.0 2.0 1.6 1.5 0.2

16.0

Amps

S0516R 16 10 50 1 30 .01 0.5 1.0 1.6 1.5 0.2

S1016R 16 10 100 1 30 .01 0.5 1.0 1.6 1.5 0.2

S2016R 16 10 200 1 30 .01 0.5 1.0 1.6 1.5 0.2

S4016R 16 10 400 1 30 .01 0.5 1.0 1.6 1.5 0.2

S6016R 16 10 600 1 30 .01 0.5 1.0 1.6 1.5 0.2

S8016R 16 10 800 1 30 .02 1.0 2.0 1.6 1.5 0.2

KAG

SCRs

Teccor Elec tronics, Inc. 6-5 SCRs

(972) 580-7777

Electrica l Specification Notes

(1) See Fig ures 6. 5 thr ough 6.16 for current rating at specified op erat-

ing case temperature.

(2) See Figures 6 .1 and 6.2 fo r free air current rating.

(3) See Figures 6.19 and 6.20 for instantaneo us on-state current vs

on-state voltage (typical).

(4) See Figure 6.18 for IGT vs TC.

(5) See Figure 6.17 for IH vs TC.

(6) For mo re than one full cycl e rating, see F igure 6.23.

(7) See Figure 6.22 for tgt vs IGT.

(8) See Figure 6.21 for VGT vs TC.

(9) Test condit ions ar e as follows: iT = 1A for 1.0A devices and 2A for

all other devices. Pulse duration = 50µs, dv/dt = 20V/µs, di/dt =

-10A/µs for 1.0A devices, and -30A/µs fo r other devices. IGT =

200mA at tur n -o n.

(10) See Figures 6. 5 through 6.10 for maxi mum allowable case tem-

peratures at maximum rated current.

(11) Pulse width ≤ 10µs.

(12) Initial on-st ate cur rent = 200mA(DC) for 1 through 16 A device s;

400mA(DC) for 20A through 70A devices.

(13) TC = TJ for test conditions in off-state.

(14) The “R”, “K” or “M” package rating is intended for high surge condi-

tion use onl y and not recommend ed for ≥50A(RMS) continuous

cu rrent us e si nc e na r row pin lea d t e mp er a tur e ca n ex ce ed PC B

solder melting tem per a ture. Rec om men d f or ≥50A(RMS) continu-

ous current require ments, Teccor's “J” or “W” pack age.

(15) For va rious durations of an exponentially decaying current wave-

form, see Figures 6.3 and 6.4. (tw is defined as 5 time const ants. )

IHIGM PGM PG(AV) ITSM dv/dt I2tdi/dt tgt tq

Holding

Current

Gate Open

(5) (12)

mAmps

Peak

Gate

Current

(11)

Amps

Peak

Gate

Power

Dissipation

(11)

Watts

Average

Gate

Power

Dissipation

Watts

Peak One

Cycle Surge

Forward

Current

(6) (10) (15)

Amps

Critical

Rate-of-Applied

Forward Voltage

Volts/µSec

RMS Surge

(Non-Repetitive)

On-State Current

f or a Per iod of

8.3 ms for

Fusing

Amps2Sec

Maximum

Rate-of-

Change of

On-State

Current

IGT = 150mA

with 0.1µs

Rise Time

Amps/µSec

Gate Controlled

Turn-On Time

Gate Pulse

= 100mA

Min. Width = 15µs

with Rise Time

≤ 0.1µs

(7)

µSec

Circuit

Commutated

Turn-Off

Time

(9) (10)

µSec60Hz 50Hz TC =

100°C TC =

125°C

MAX MIN MIN TYP MAX

30 2.0 20 0.5 100 83 350 250 41 100 2.0 35

30 2.0 20 0.5 100 83 300 225 41 100 2.0 35

30 2.0 20 0.5 100 83 250 200 41 100 2.0 35

30 2.0 20 0.5 100 83 350 250 41 100 2.0 35

30 2.0 20 0.5 100 83 300 225 41 100 2.0 35

30 2.0 20 0.5 100 83 250 200 41 100 2.0 35

40 2.0 20 0.5 120 100 350 250 60 100 2.0 35

40 2.0 20 0.5 120 100 300 225 60 100 2.0 35

40 2.0 20 0.5 120 100 250 200 60 100 2.0 35

40 3.0 30 0.6 225 188 450 350 210 125 2.0 35

40 3.0 30 0.6 225 188 425 325 210 125 2.0 35

40 3.0 30 0.6 225 188 400 300 210 125 2.0 35

40 3.0 30 0.6 225 188 450 350 210 125 2.0 35

40 3.0 30 0.6 225 188 425 325 210 125 2.0 35

40 3.0 30 0.6 225 188 400 300 210 125 2.0 35

Electrical Specifications

SCRs 6-6 Teccor Electronics, Inc.

(972) 580-7777

See General Notes and Electrical Specification Notes on pa

es 6-4 and 6-5.

TYPE

Part Number IT

VDRM &

VRRM IGT IDRM & I RRM VTM

Isolated Non-Isolated

220AB TO

218X TO

218AC TO

220AB TO

218X TO

218AC

Maximum

On-State

Current

(1) (14)

Amps

Repetitive

Peak

Off-State

Forward

and

Reverse

Voltage

Volts

DC Gate

Trigger

Current

VD = 12VDC

RL = 30Ω

(4)

mAmps

Peak Off-State

Forward and Reverse

Current at VDRM and VRRM

(13)

mAmps

Peak

On-State

Voltage at

Max

Rated

RMS

Current

TC = 25°C

(3)

VoltsIT(RMS) IT(AV)

TC =

25°C TC =

100°C TC =

125°C

See “Package Dimensions” section for variations. MAX MIN MIN MAX MAX MAX

Amps

S0520L 20 12.8 50 130 .01 0.5 1.0 1.6

S1020L 20 12.8 100 130 .01 0.5 1.0 1.6

S2020L 20 12.8 200 130 .01 0.5 1.0 1.6

S4020L 20 12.8 400 130 .01 0.5 1.0 1.6

S6020L 20 12.8 600 130 .01 0.5 1.0 1.6

S8020L 20 12.8 800 130 .02 1.0 2.0 1.6

Amps

S0525L S0525R 25 16 50 1 35 .01 1.0 2.0 1.6

S1025L S1025R 25 16 100 1 35 .01 1.0 2.0 1.6

S2025L S2025R 25 16 200 1 35 .01 1.0 2.0 1.6

S4025L S4025R 25 16 400 1 35 .01 1.0 2.0 1.6

S6025L S6025R 25 16 600 1 35 .01 1.0 2.0 1.6

S8025L S8025R 25 16 800 1 35 .02 1.5 3.0 1.6

Amps

S0535J S0535K 35 22 50 540 .01 1.0 2.0 1.8

S1035J S1035K 35 22 100 540 .01 1.0 2.0 1.8

S2035J S2035K 35 22 200 540 .01 1.0 2.0 1.8

S4035J S4035K 35 22 400 540 .01 1.0 2.0 1.8

S6035J S6035K 35 22 600 540 .01 1.0 2.0 1.8

S8035J S8035K 35 22 800 540 .02 1.5 3.0 1.8

Amps

S0540R 40 25 50 5 40 .01 1.0 2.0 1.8

S1040R 40 25 100 5 40 .01 1.0 2.0 1.8

S2040R 40 25 200 5 40 .01 1.0 2.0 1.8

S4040R 40 25 400 5 40 .01 1.0 2.0 1.8

S6040R 40 25 600 5 40 .01 1.0 2.0 1.8

S8040R 40 25 800 5 40 .02 1.5 3.0 1.8

Amps

S0555R S0555W S0555M 55 35 50 540 .01 1.0 2.0 1.8

S1055R S1055W S1055M 55 35 100 540 .01 1.0 2.0 1.8

S2055R S2055W S2055M 55 35 200 540 .01 1.0 2.0 1.8

S4055R S4055W S4055M 55 35 400 540 .01 1.0 2.0 1.8

S6055R S6055W S6055M 55 35 600 540 .01 1.0 2.0 1.8

S8055R S8055W S8055M 55 35 800 540 .02 1.5 3.0 1.8

Amps

S0565J S0565K 65 41 50 5 50 .02 1.5 3.0 1.8

S1065J S1065K 65 41 100 5 50 .02 1.5 3.0 1.8

S2065J S2065K 65 41 200 5 50 .02 1.5 3.0 1.8

S4065J S4065K 65 41 400 5 50 .02 1.5 3.0 1.8

S6065J S6065K 65 41 600 5 50 .02 1.5 3.0 1.8

S8065J S8065K 65 41 800 5 50 .02 2.0 5.0 1.8

Amps

S0570W 70 45 50 550 .02 1.5 3.0 1.8

S1070W 70 45 100 550 .02 1.5 3.0 1.8

S2070W 70 45 200 550 .02 1.5 3.0 1.8

S4070W 70 45 400 550 .02 1.5 3.0 1.8

S6070W 70 45 600 550 .02 1.5 3.0 1.8

S8070W 70 45 800 550 .02 2.0 5.0 1.8

KAG

SCRs

Teccor Elec tronics, Inc. 6-7 SCRs

(972) 580-7777

See General Notes and Electrical Specification Notes on pa

es 6-4 and 6-5.

VGT IHIGM PGM PG(AV) ITSM dv/dt I2tdi/dt tgt tq

DC Gate

Trigger

Voltage

VD = 12VDC

RL = 30Ω

(8)

Volts

Holding

Current

Gate

Open

(5) (12)

mAmps

Peak

Gate

Current

(11)

Amps

Peak

Gate

Power

Dissi-

pation

(11)

Watts

Average

Gate

Power

Dissipa-

tion

Watts

Peak One

Cycle Surge

Forward Current

(6) (10) (15)

Amps

Critical Rate-

of-Applied

Forward Voltage

Volts/µSec

RMS Surge

(Non-Repeti-

tive)

On-State

Current

for a Period

of 8.3 msec

for Fusi ng

Amps2Sec

Maximum

Rate-of-

Change of

On-State

Current

IGT = 150mA

with 0.1µS

Rise Time

Amps/µSec

Gate Controlled

Turn-On Time

Gate Pulse

= 150mA

Min. Width

= 15µS with

Rise Time

≤ 0.1µS

(7)

µSec

Circuit

Commutated

Turn-Off

Time

(9) (10)

µSec

TC =

25°C TC =

125°C 60 Hz 50 Hz TC = 100°C TC = 125°C

MAX MIN MAX MIN MIN TYP MAX

1.5 0.2 40 3.0 30 0.6 300 255 450 350 374 125 2.0 35

1.5 0.2 40 3.0 30 0.6 300 255 425 325 374 125 2.0 35

1.5 0.2 40 3.0 30 0.6 300 255 400 300 374 125 2.0 35

1.5 0.2 50 3.5 35 0.8 350 300 450 350 510 150 2.0 35

1.5 0.2 50 3.5 35 0.8 350 300 425 325 510 150 2.0 35

1.5 0.2 50 3.5 35 0.8 350 300 400 300 510 150 2.0 35

1.5 0.2 50 3.5 35 0.8 500 425 450 350 1035 150 2.0 35

1.5 0.2 50 3.5 35 0.8 500 425 425 325 1035 150 2.0 35

1.5 0.2 50 3.5 35 0.8 500 425 400 300 1035 150 2.0 35

1.5 0.2 60 3.5 35 0.8 520 430 650 550 1122 175 2.5 35

1.5 0.2 60 3.5 35 0.8 520 430 600 500 1122 175 2.5 35

1.5 0.2 60 3.5 35 0.8 520 430 500 475 1122 175 2.5 35

1.5 0.2 60 4.0 40 0.8 650 550 650 550 1750 175 2.5 35

1.5 0.2 60 4.0 40 0.8 650 550 600 500 1750 175 2.5 35

1.5 0.2 60 4.0 40 0.8 650 550 500 475 1750 175 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 650 550 3745 200 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 600 500 3745 200 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 500 475 3745 200 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 650 550 3745 200 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 600 500 3745 200 2.5 35

2.0 0.2 80 5.0 50 1.0 950 800 500 475 3745 200 2.5 35

Electrical Specifications

SCRs 6-8 Teccor Electronics, Inc.

(972) 580-7777

Electrica l Isolation

Teccor’s isolated SCR packages will w iths tand a mini m um high

potenti al test of 2500VAC( R M S) from lead s to mounting tab over

the device' s operatin g temperature range. See table below for

standard and optional isolation rating s.

*For 4000V isolation, add “V” suffix to part number.

**UL Reco

nized File #E71639.

THERMAL RESISTANCE (STEADY STATE)

RθJC [RθJA] °C/W (TYP.)

Type

TO-92

THERMOTAB

TO-220AB

Type 1

TO-202

Type 2

TO-202

Non-Isolated

TO-220AB

Isolated

TO-218X

Non-Isolated

TO-218X

Isolated

TO-218AC

Non-Isolated

TO-218AC

1.0 Amp 50 [14 5]

6.0 Amps 4.0 [50] 4.3 9.5 [70]

8.0 Amps 3.4 3.9 2.1 [40]

10.0 Amps 3.0 3.4 1.9

12.0 Amps 1.7

15.0 Amps 2.5

16.0 Amps 1.5

20.0 Amps 2.4

25.0 Amps 2.35 1.1

35.0 Amps .70 .70

40.0 Amps 0.66

55.0 Amps 0.58 .53 .53

65.0 Amps .86 .86

70.0 Amps .60

Electrical Iso la tion

from Leads to Mounti ng Tab

VAC(RMS) Isolated **

TO-220AB Isolated **

TO-218X Isolated **

TO-218AC

2500 Standard Standard Standard

4000 Optional * N/A N/A

SCRs

Teccor Elec tronics, Inc. 6-9 SCRs

(972) 580-7777

ure 6.1 Max imum Allowable A mbient Temperature vs RMS On-

State Current

ure 6.2 Max imum Allowable A mbient Temperature vs Avera

e On-

State Current

ure 6.3 Peak Capacitor Dischar

e Current f or 12R, 16R, and 25R

ure 6.4 Peak Capacitor Dischar

e Current Deratin

for 12R, 16R,

and 25R

ure 6.5 Max imum Allowable Case Temperature v s RMS On-State

Current (TO-92, 1 Amp)

ure 6.6 Max imum Allowable Case Temperature v s RMS On-State

Current (6, 8, and 10 Amps)

100

120

00.2 0.4 0.6 0.1 1.0 1.2 1.4 1.6 1.8 2.0 2.2

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

FREE AIR RATING

6 AMP TO-220 (ISOLATED) & 6 AMP TO-202 (TYPE 1 & 3)

1 AMP TO-92 DEVICES

8 AMP TO-220 (NON-ISOLATED)

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable

Ambient Temperature (TA) - ˚ C

100

120

00.2 0.4 0.6 0.8 1.0 1.2 1.4

Maximum Allowable

Ambient Temperature (TA) - ˚C

Average On-State Current [IT(AV)] - Amps

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180

FREE AIR RATING

8 AMP TO-220 (N0N-ISOLATED)

1 AMP TO-92 DEVICES

6-AMP TO-220 (ISOLATED) & 6 AMP TO-202 (TYPE 1 & 3)

0.5 1.0 2.0 5.0 10 20 50

100

200

300

1000

Pulse Current Duration (tW) - mSec.

Peak Discharge Current (ITM) - Amps

SXX25R

SXX16R

SXX12R

ITM

tW= 5 times constants

25 50 75 100 125

0.2

0.4

0.6

0.8

1.0

Case Temperature (TC) - ˚C

Normalized Peak Current

100

110

120

130

RMS On-State Current

[IT(RMS)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

0.4 .8 1.2.6

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as

shown on dimensional drawing

1 AMP TO-92

1.0

02 4681012

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180º

CASE TEMPERATURE: Measure as

shown on dimensional drawings

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

8 AMP TO-220 (ISOLATED)

& 8 AMP TO-202

6 AMP DEVICES

8 AMP TO-220

(NON-ISOLATED)

10 AMP TO-220 (ISOLATED)

& 10 AMP T202

Electrical Specifications

SCRs 6-10 Teccor Electronics, Inc.

(972) 580-7777

ure 6.7 Max imum Allowable Case Temperature v s RMS On-State

Current (10, 12, 16, and 20 Am ps)

ure 6.8 Max imum Allowable Case Temperature v s RMS On-State

Current (25 and 35 A mps )

ure 6.9 Max imum Allowable Case Temperature v s RMS On-State

Current (40-70 Amps)

ure 6.10 Maximum Allowable Case Tem perature v s RM S On-State

Current (55 and 65 A mps )

ure 6.11 Maximum Allowable Case Temperature vs Avera

e On-

State Current (TO-92, 1 Amp)

ure 6.12 Maximum Allowable Case Tem perature v s Avera

e On-

State Current (8, 10, and 12 Amps)

0 4 8 12 16 20

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as shown

on dimensional drawings

16 AMP TO-220 (NON-ISOLATED)

20 AMP TO-220

(ISOLATED)

15 AMP

TO-220 (ISOLATED)

12 AMP TO-220 (NON-ISOLATED)

10 AMP TO-220 (NON-ISOLATED)

RMS On-State Current [IT

(

RMS

)

] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

0 4 8 12 16 20 24 28 32 36

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180

CASE TEMPERATURE: Measure as shown

on dimensional drawings

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

35 AMP TO-218

(ISOLATED)

25 AMP TO-220

(NON-ISOLATED)

25 AMP TO-220

(ISOLATED)

0 10203040506070

100

110

120

130

RMS On-State Current [IT

(

RMS

)

] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

65 AMP TO-218X

(ISOLATED)

55 AMP TO-218X

(NON-ISOLATED)

70 AMP TO-218X (NON-ISOLATED)

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as

shown on dimensional drawings

40 AMP TO-220

(NON-ISOLATED)

010203040

100

110

120

130

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable Case Temperature (TC) - ˚C

50 60 70 75

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as

shown on dimensional drawings

*THE "R", "K" or "M"

PACKAGE RATING

IS INTENDED FOR HIGH SURGE

CONDITION USE ONLY AND IS NOT

RECOMMENDED FOR >50 AMPS (RMS)

CONTINUOUS CURRENT USE, SINCE

NARROW PIN LEAD TEMPERATURE

CAN EXCEED PCB SOLDER MELTING

TEMPERATURE. "J" OR "W" PACKAGES

ARE RECOMMEND FOR >50AMPS (RMS)

CONTINUOUS CURRENT REQUIREMENTS.

65 AMP TO-218AC

(ISOLATED)

*55 AMP TO-218AC

(NON-ISOLATED)

*55AMP TO-220

(NON-ISOLATED)

0.2.4.6.8

100

110

120

130

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as

shown on dimensional drawings

Average On-State Current

[IT(AV)] - Amps

Maximum Allowable Case Temperature (TC) - ˚C

1 AMP TO-92

10 2345678

100

110

120

130

Average On-State Current [IT(AV)] - Amps

Maximum Allowable Case Temperature (TC) - ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as shown

on dimensional drawings

8 AMP TO-220

(NON-ISOLATED)

10 AMP TO-220 (ISOLATED)

& 10 AMP TO-202

8 AMP TO-220 (ISOLATED)

8 AMP TO-202

6 AMP

DEVICES

10 AMP TO-220

(NON-ISOLATED)

12 AMP TO-220

(NON-ISOLATED)

SCRs

Teccor Electronics, Inc. 6-11 SCRs

(972) 580-7777

ure 6.13 Maximum Allowable Case Tem perature v s Avera

e On-

State Current (10-20 A mps)

ure 6.14 Maximum Allowable Case Tem perature v s Avera

e On-

State Current (25 and 35 Amps)

ure 6.15 Maximum Allowable Case Tem perature v s Avera

e On-

State Current (40-70 A mps)

ure 6.16 Maximum Allowable Case Tem perature v s Avera

e On-

State Current (55 and 65 Amps)

ure 6.17 Normalized DC Hol din

Current vs Case Temperature

ure 6.18 Normalized DC Gate-Tri

er Current vs Case Temperature

0 2 4 6 8 10 12 14

100

110

120

130

Average On-State Current [IT(AV)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measured as

shown on dimensional drawings

20 AMP TO-220

(ISOLATED)

15 AMP TO-220

(ISOLATED)

10 AMP TO-220

(NON-ISOLATED)

16 AMP TO-220 (NON-ISOLATED)

0 .4 8 12 16 20 24

100

110

120

130

Average On-State Current [IT

(

)

] - Amps

Maximum Allowable Case Temperature (TC) - ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as

shown on dimensional drawings

35 AMP TO-218 (NON-ISOLATED)

35 AMP TO-218 (ISOLATED)

25 AMP TO-220 (NON-ISOLATED)

25 AMP TO-220 (ISOLATED)

0 1020304050

100

110

120

130

Average On-State Current [IT(AV)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as shown

on dimensional drawings

65 AMP TO-218X

(ISOLATED)

55 AMP TO-218X

(NON-ISOLATED)

70 AMP TO-218X

(NON-ISOLATED)

40 AMP T0-220

(NON-ISOLATED)

0 1020304050

100

110

120

130

Average On-State Current [IT(AV)] - Amps

Maximum Allowable

Case Temperature (TC) - ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

CASE TEMPERATURE: Measure as shown

on dimensional drawings

*55 AMP TO-218AC (NON-ISOLATED)

*THE "R", "K", OR "M" PACKAGE

RATING IS INTENDED FOR HIGH

SURGE CONDITION USE ONLY AND

NOT RECOMMENDED FOR >32 AMPS

(AV) CONTINUOUS CURRENT USE SINCE

NARROW PIN LEAD TEMPERATURE

CAN EXCEED PCB SOLDER MELTING

TEMPERATURE. "J" OR "W" PACKAGES

ARE RECOMMEND FOR >32 AMPS (AV)

CONTINUOUS CURRENT REQUIREMENTS.

65 AMP TO-218AC

(ISOLATED)

55 AMP TO-220

(NON-ISOLATED)

-40 -15 +25 +65 +105 +125

1.0

1.5

2.0

Case Temperature (TC) - ˚C

Ratio of IH

IH (TC = 25˚C)

INITIAL ON-STATE

CURRENT = 200 mA (DC)

FOR 1-20 AMP DEVICES

AND 400 mA (DC) FOR

25-70 AMP DEVICES

-40 -15 +25 +65 +105 +125

1.0

1.5

2.0

Case Temperature (TC) - ˚C

Ratio of IGT

IGT (TC = 25˚C)

Electrical Specifications

SCRs 6-12 Teccor Electronics, Inc.

(972) 580-7777

ure 6.19 Instantaneous On-State Current vs On-State Volta

(Typical) (6-25 Am ps)

ure 6.20 Instantaneous On-State Current vs On-State Volta

(Typical) (35-70 Am ps)

ure 6.21 Normalized DC Gate-Tri

er Vol ta

e vs Ca se Temper at ur e

ure 6.22 Typical Turn-On Time vs Gate-Tri

er Current

0 .6 .8 1.0 1.2 1.4 1.6

Instantaneous On-State Voltage (vT) - Volts

Instantaneous On-State Current (iT) - Amps

TC = 25˚C

12 AMP DEVICES

25 AMP DEVICES

15-20 AMP DEVICES

1 AMP DEVICE

6-10 AMP DEVICES

0 .6 .8 1.0 1.2 1.4 1.6

100

120

140

160

180

200

Instantaneous On-State Voltage (vT) - Volts

Instantaneous On-State

Current (iT) - Amps

TC = 25˚C

65 & 70 AMP DEVICES

55 AMP DEVICES

35-40 AMP DEVICES

-40 -15 +25 +65 +105 +125

1.0

1.5

Case Temperature (TC) - ˚C

Ratio of VGT

VGT (TC = 25˚C)

10 20 30 40 50 60 80 100 200

Turn-On Time (tgt) - µSec.

DC Gate Trigger Current (IGT) - mA

6-12 AMP DEVICES

1 AMP

DEVICE

40-70 AMP DEVICES

15-35 AMP DEVICES

TC = 25˚C

SCRs

Teccor Electronics, Inc. 6-13 SCRs

(972) 580-7777

ure 6.23 Peak Sur

e Current vs Sur

e Current Duration

ure 6.24 Power Dissipation ( Typical) vs RMS On-State Current

(TO-92, 1 Amp) Fi

ure 6.25 Power Dissipation (Typical) vs RMS On-State Current

(6-20 Amps)

1000

100

200

300

400

500

600

800

123 54 6 7 8 10 20 30 40 60 80 100 200 300 400 600 1000

Surge Current Duration - Full Cycles

70 AMP DEVICES

65 AMP TO-218

55 AMP DEVICES

25 AMP DEVICES

35 AMP DEVICES

20 AMP DEVICES

16 AMP DEVICES

15 AMP DEVICES

12 AMP DEVICES

10 AMP DEVICES

1.0 AMP DEVICES

SUPPLY FREQUENCY: 60 Hz Sinusoidal

LOAD: Resistive

RMS ON-STATE CURRENT: [IT(RMS)]: Max

Rated Value at Specified Case Temperature

GATE CONTROL MAY BE LOST

DURING AND IMMEDIATELY

FOLLOWING SURGE CURRENT

INTERVAL.

OVERLOAD MAY NOT BE REPEATED

UNTIL JUNCTION TEMPERATURE

HAS RETURNED TO STEADY-STATE

RATED VALUE.

8 AMP DEVICES

6 AMP DEVICES

40 AMP DEVICES

Maximum Allowable Case Temperature (TC) - ˚C

0.2.4.6.8

1.0

RMS On-State Current [IT(RMS)] - Amps

Average On-State Power

Dissipation [PD(AV)] - Watts

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

1.0 AMP DEVICE

0481216

RMS On-State Current [IT(RMS)] - Amps

Average On-State

Power Dissipation [PD(AV)] - Watts

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

2 6 10 14 18

15-20 AMP DEVICES

12 AMP DEVICE

6-10 AMP DEVICES

Electrical Specifications

SCRs 6-14 Teccor Electronics, Inc.

(972) 580-7777

ure 6.26 Power Dissipation ( Ty pic al) vs RM S On-State Current

(25 and 35 Amps)

ure 6.27 Power Dissipation ( Ty pic al) vs RM S On-State Current

(40-70 Amps)

0 8 16 24 32

RMS On-State Current [IT

(

RMS

)

] - Amps

Average On-State

Power Dissipation [PD(AV)] - Watts

412202836

25 AMP TO-220 DEVICES

35 AMP DEVICES

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

RMS On-State Current [IT

(

RMS

)

] - Amps

Average On-State

Power Dissipation [PD(AV)] - Watts

0 10203040506070

65 & 70 AMP DEVICES

CURRENT WAVEFORM: Half Sine Wave

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180˚

40 & 55 AMP DEVICES