4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SVPA Low ESR, Series Large ripple current Marking : Polarity( ), Rated voltage (Purple) PA(B6, C6), SVPA(E7, F8), Rated capacitance, Lot.No. Specifications Items Category temperature range Tolerance on rated capacitance Tangent of loss angle Leakage current 1 ESR Characteristics of impedance ratio at high temp. and low temp. Characteristics -55C to +105C M : 20% 120Hz Less than or equal to the value of Table5 120Hz Less than or equal to the value of Table5 After 2 minutes Less than or equal to the value of Table5 Z / Z 20C 0.75 to 1.25 -55C Based the value at 0.75 to 1.25 Z / Z 20C +105C 100KHz+20C Within 20% C/C 1.5 times or less than an initial standard 105C, 2,000h, Rated tan Endurance 1.5 times or less than an initial standard voltage applied ESR Leakage current Below an initial standard Within 20% C/C 60C, 90 to 95%RH, 1.5 times or less than an initial standard tan Damp heat (Steady state) 1,000h, 1.5 times or less than an initial standard ESR No-applied voltage Leakage current Below an initial standard (after voltage processing) Within 10% C/C Resistance to 1.3 times or less than an initial standard tan 2 (VPS) (230C X 75s) soldering heat 1.3 times or less than an initial standard ESR Leakage current Below an initial standard (after voltage processing) Conditions 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105C . 2 Refer to Page 56 for reflow soldering conditions. Dimensions Size List F 10 22 39 47 68 82 120 150 180 220 270 330 470 680 820 2.5 3.3 B6 C6 E7 P C H W L RV SV (unit : mm) 0.2max. D Specificationsfor eachseries This is a low ESR series based on the SVP series. Suitable for miniaturizing devices and circuits. This product can support lead free-reflow(2). R Size Code D0.5 B6 C6 E7 F8 5.0 6.3 8.0 10.0 H0.2 C0.2 R P0.2 5.3 6.6 8.3 10.3 5.3 6.6 8.3 10.3 6.0 7.3 9.0 11.0 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 1.4 2.1 3.2 4.6 5.9 5.9 6.9 7.9 RV : Rated voltage (SV) : Surge (room temperature) 4 6.3 10 16 20 5.2 8.2 11.5 18.4 23.0 B6 C6 C6 B6 E7 C6 B6 E7 C6 E7 C6 F8 E7 E7 F8 F8 F8 F8 For the minimum packing quantity, please refer to page 55. 26 +0.1 L W0.2 -0.4 4. SPECIFICATIONS FOR EACH SERIES Table5 SVPA Series Characteristics List Size Code Rated Voltage (V) Part Number 1 20SVPA10M Rated Capacitance (F) 20 ESR (m) (max.) 100kHz Rated ripple current Tangent of loss angle (max.) 300kHz 3 100kHz (mArms) at 105C Leakage current (A) (max.)2 10 40 35 1700 0.12 80 6SVPA47MAA 6.3 47 30 26 1970 0.12 300 4SVPA68MAA 4 68 30 26 1970 0.12 300 2R5SVPA82MAA 2.5 82 30 26 1970 0.12 300 C6 20SVPA22M 20 22 35 31 2040 0.12 88 16SVPA39MAA 16 39 35 31 2040 0.12 300 16SVPA39MAAY 16 39 24 20 2460 0.12 300 10SVPA68MAA 10 68 30 26 2200 0.12 300 6SVPA120MAA 6.3 120 22 19 2570 0.12 300 4SVPA150MAA 4 150 22 19 2570 0.12 300 2R5SVPA180MAA 2.5 180 20 18 2690 0.12 300 20SVPA47M 20 47 33 29 2630 0.12 188 16SVPA82MAA 16 82 30 25 2760 0.12 262 10SVPA150MAA 10 150 30 25 2760 0.12 500 Specificationsfor eachseries B6 E7 F8 1 2 3 6SVPA220MAA 6.3 220 22 19 3220 0.12 500 4SVPA270MAA 4 270 22 19 3220 0.12 500 2R5SVPA330MAA 2.5 330 20 18 3370 0.12 500 16SVPA180M 16 180 29 28 3430 0.12 576 10SVPA330M 10 330 24 23 3770 0.12 660 6SVPA470M 6.3 470 20 19 4130 0.12 592 4SVPA680M 4 680 20 19 4130 0.12 544 2R5SVPA820M 2.5 820 19 18 4240 0.12 500 Capacitance tolerance : M 20% After 2 minutes The ESR value at 300kHz is a reference one. Recommended land pattern dimension of PWB c (unit : mm) a b Size Code B6 C6 E7 F8 a 1.4 2.1 2.8 4.3 b 7.4 9.1 11.1 13.1 c 1.6 1.6 1.9 1.9 Frequency coefficient for ripple current Frequency Coefficient 120Hz f 1kHz 0.05 1kHz f 10kHz 0.3 10kHz f 100kHz 0.7 100kHz f 500kHz 1 27