■Specifications
■Dimensions
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105°C .
※2 Refer to Page 56 for reflow soldering conditions.
B6
C6
E7
F8
φD±0.5
5.0
6.3
8.0
10.0
W±0.2
5.9
5.9
6.9
7.9
5.3
6.6
8.3
10.3
H±0.2
5.3
6.6
8.3
10.3
C±0.2
6.0
7.3
9.0
11.0
R
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
0.6 to 0.8
P±0.2
1.4
2.1
3.2
4.6
Size Code
(unit : mm)
■Size List
26
10
22
39
47
68
82
120
150
180
220
270
330
470
680
820
B6
C6
E7
F8
B6
C6
E7
F8
B6
C6
E7
F8
C6
E7
F8
C6
E7
F8
RV
（SV）
µ
F
2.5
（3.3）4
（5.2）6.3
（8.2）10
（11.5）16
（18.4）
B6
C6
E7
20
（23.0）
RV : Rated voltage (SV) : Surge (room temperature)
This is a low ESR series based on the SVP series. Suitable for
miniaturizing devices and circuits.
This product can support lead free-reflow(※2).
Marking : Polarity( ), Rated voltage
(Purple) PA(B6, C6), SVPA(E7, F8),
Rated capacitance, Lot.No.
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
φD
L
P
R
C
W
0.2max.
H
（＋）
※For the minimum packing quantity, please refer to page 55.
Conductive polymer type
SVPASeries
Low ESR,
Large ripple current
L+0.1
-0.4
Items Characteristics
-55°C to +105°C
M : ±20%
Less than or equal to the value of Table5
Less than or equal to the value of Table5
Less than or equal to the value of Table5
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard (after voltage processing)
Within ±10%
1.3 times or less than an initial standard
1.3 times or less than an initial standard
Below an initial standard (after voltage processing)
Category temperature range
Tolerance on rated capacitance
Tangent of loss angle
Leakage current
ESR
Endurance
Damp heat (Steady state)
Characteristics of impedance
ratio at high temp. and low temp.
-55°C
+105°C
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Resistance to
soldering heat
Z / Z 20°C
Z / Z 20°C
0.75 to 1.25
0.75 to 1.25
120Hz
120Hz
105°C, 2,000h, Rated
voltage applied
60°C, 90 to 95%RH,
1,000h,
No-applied voltage
(VPS) (230°C X 75s)
※1
※2
Conditions
Based the value at
100KHz，+20°C
After 2 minutes
27
■Table5 SVPA Series Characteristics List
※1 Capacitance tolerance : M ±20%
※2 After 2 minutes
※3 The ESR value at 300kHz is a reference one.
B6
20
6.3
4
2.5
20
16
16
10
6.3
4
2.5
20
16
10
6.3
4
2.5
16
10
6.3
4
2.5
10
47
68
82
22
39
39
68
120
150
180
47
82
150
220
270
330
180
330
470
680
820
40
30
30
30
35
35
24
30
22
22
20
33
30
30
22
22
20
29
24
20
20
19
35
26
26
26
31
31
20
26
19
19
18
29
25
25
19
19
18
28
23
19
19
18
1700
1970
1970
1970
2040
2040
2460
2200
2570
2570
2690
2630
2760
2760
3220
3220
3370
3430
3770
4130
4130
4240
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
80
300
300
300
88
300
300
300
300
300
300
188
262
500
500
500
500
576
660
592
544
500
Size
Code Part Number
※1
ESR (mΩ) (max.)
C6
E7
F8
Rated
ripple current
100kHz (mArms) at 105°C
Tangent of
loss angle
(max.)
Leakage
current (µA)
(max.)※2
100kHz 300kHz ※3
■Recommended land pattern
dimension of PWB
Size Code
B6
C6
E7
F8
ab c
1.4
2.1
2.8
4.3
7.4
9.1
11.1
13.1
1.6
1.6
1.9
1.9
(unit : mm)
Rated
Voltage
(V)
Rated
Capacitance
(
µ
F)
Specificationsfor
eachseries
c
a
b
4. SPECIFICATIONS FOR EACH SERIES
Frequency coefficient for ripple current
Frequency
Coefficient
120Hz≦ f ＜1kHz
0.05
1kHz≦ f ＜10kHz
0.3
10kHz≦ f ＜100kHz
0.7
100kHz≦ f ≦500kHz
1
20SVPA10M
6SVPA47MAA
4SVPA68MAA
2R5SVPA82MAA
20SVPA22M
16SVPA39MAA
16SVPA39MAAY
10SVPA68MAA
6SVPA120MAA
4SVPA150MAA
2R5SVPA180MAA
20SVPA47M
16SVPA82MAA
10SVPA150MAA
6SVPA220MAA
4SVPA270MAA
2R5SVPA330MAA
16SVPA180M
10SVPA330M
6SVPA470M
4SVPA680M
2R5SVPA820M