Data sheet BMC150 6-axis eCompass Bosch Sensortec BMC150: Data sheet Document revision 1.0 Document release date 14 July 2014 Document number BST-BMC150-DS000-04 Technical reference code(s) 0 273 141 156 Notes Product photos and pictures are for illustration purposes only and may differ from the real product's appearance. Datasheet eCompass BMC150 Page 2 BMC150 ECOMPASS WITH 3-AXIS GEOMAGNETIC SENSOR AND 12 BIT 3-AXIS ACCELEROMETER Key features Three-axis magnetic field sensor and 12bit three-axis accelerometer in one package Accelerometer can still be used independently from magnetometer operation Ultra-Small package 14-Pin LGA package, footprint 2.2 x 2.2mm2, height 0.95 mm Digital interface SPI (4-wire, 3-wire), IC, 4 interrupt pins (2 acceleration sensor, 2 magnetic sensor interrupt pins) Low voltage operation VDD supply voltage range: 1.62V to 3.6V VDDIO interface voltage range: 1.2V to 3.6V Flexible functionality Acceleration ranges 2g/4g/8g/16g Acceleration Low-pass filter bandwidths 1 kHz - <8Hz Magnetic field range 1300T (x, y-axis), 2500T (z-axis) Magnetic field resolution of ~0.3T On-chip FIFO Integrated FIFO with a depth of 32 frames On-chip interrupt controller Motion-triggered interrupt-signal generation for - new data (separate for accelerometer and magnetometer) - any-motion (slope) detection - tap sensing (single tap / double tap) - orientation recognition - flat detection - low-g/high-g detection - magnetic Low-/High-Threshold detection Ultra-low power Low current consumption (190A @ 10 Hz including accelerometer and magnetic sensor in low power preset), short wake-up time, advanced features for system power management Temperature range -40 C ... +85 C Temperature sensor RoHS compliant, halogen-free Typical applications Tilt-compensated electronic compass for map rotation, navigation and augmented reality 6-axis orientation for gaming Display profile switching Menu scrolling, tap / double tap sensing Pedometer / step counting Free-fall detection Drop detection for warranty logging Advanced system power management for mobile applications Gaming BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 3 General Description The BMC150 is an integrated electronic compass solution for consumer market applications. It comprises a 12bit leading edge triaxial, low-g acceleration sensor and an ultra-low power, high precision triaxial magnetic field sensor. It allows measurements of acceleration and magnetic field in three perpendicular axes. Performance and features of both sensing technologies are carefully tuned and perfectly match the demanding requirements of all 6-axis mobile applications such as electronic compass, navigation or augmented reality. An evaluation circuitry (ASIC) converts the output of the micromechanical sensing structures (MEMS) to digital results which can be read out over the industry standard digital interfaces. Package and interfaces of the BMC150 have been designed to match a multitude of hardware requirements. As the sensor features an ultra-small footprint and a flat package, it is ingeniously suited for mobile applications. The BMC150 offers ultra-low voltage operation (VDD voltage range from 1.62V to 3.6V, VDDIO voltage range 1.2V to 3.6V) and can be programmed to optimize functionality, performance and power consumption in customer specific applications. The programmable interrupt engine sets new standards in terms of flexibility. The BMC150 senses orientation, tilt, motion, shock, vibration and heading in cell phones, handhelds, computer peripherals, man-machine interfaces, virtual reality features and game controllers. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 4 Index of Contents 1. SPECIFICATION ........................................................................................................................ 7 1.1 COMPASS ELECTRICAL SPECIFICATION ................................................................................. 7 1.2 ACCELEROMETER SPECIFICATION ........................................................................................ 8 1.3 MAGNETOMETER SPECIFICATION ....................................................................................... 11 2. ABSOLUTE MAXIMUM RATINGS .......................................................................................... 15 3. BLOCK DIAGRAM ................................................................................................................... 16 4. FUNCTIONAL DESCRIPTION ................................................................................................. 17 4.1 SUPPLY VOLTAGE AND POWER MANAGEMENT ..................................................................... 17 4.2 POWER MODES ................................................................................................................. 17 4.2.1 ACCELEROMETER POWER MODES ................................................................................................. 18 4.2.2 MAGNETOMETER POWER MODES .................................................................................................. 22 4.2.3 BMC150 OVERALL POWER CONSUMPTION .................................................................................... 25 4.3 SENSOR DATA .................................................................................................................. 26 4.3.1 ACCELERATION DATA ................................................................................................................... 26 4.3.2 TEMPERATURE SENSOR................................................................................................................ 27 4.3.3 MAGNETIC FIELD DATA.................................................................................................................. 27 4.3.4 MAGNETIC FIELD DATA TEMPERATURE COMPENSATION................................................................... 29 4.4 SELF-TEST ....................................................................................................................... 30 4.4.1 ACCELEROMETER SELF-TEST ........................................................................................................ 30 4.4.2 MAGNETOMETER SELF-TEST ......................................................................................................... 31 4.5 ACCELEROMETER OFFSET COMPENSATION ......................................................................... 33 4.5.1 SLOW COMPENSATION.................................................................................................................. 35 4.5.2 FAST COMPENSATION ................................................................................................................... 35 4.5.3 MANUAL COMPENSATION .............................................................................................................. 36 4.5.4 INLINE CALIBRATION ..................................................................................................................... 36 4.6 NON-VOLATILE MEMORY .................................................................................................... 37 4.6.1 ACCELEROMETER NON-VOLATILE MEMORY .................................................................................... 37 4.6.2 MAGNETOMETER NON-VOLATILE MEMORY ..................................................................................... 37 4.7 ACCELEROMETER INTERRUPT CONTROLLER ....................................................................... 38 4.7.1 GENERAL FEATURES .................................................................................................................... 38 4.7.2 MAPPING TO PHYSICAL INTERRUPT PINS (INTTYPE TO INT PIN#) ..................................................... 39 4.7.3 ELECTRICAL BEHAVIOR (INT PIN# TO OPEN-DRIVE OR PUSH-PULL) .................................................. 40 4.7.4 NEW DATA INTERRUPT .................................................................................................................. 40 4.7.5 SLOPE / ANY-MOTION DETECTION .................................................................................................. 41 4.7.6 TAP SENSING ............................................................................................................................... 43 4.7.7 ORIENTATION RECOGNITION ......................................................................................................... 46 4.7.8 FLAT DETECTION .......................................................................................................................... 51 4.7.9 LOW-G INTERRUPT ....................................................................................................................... 52 4.7.10 HIGH-G INTERRUPT .................................................................................................................... 53 4.7.11 NO-MOTION / SLOW MOTION DETECTION ...................................................................................... 54 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 5 4.8 ACCELEROMETER SOFTRESET ........................................................................................... 56 4.9 MAGNETOMETER INTERRUPT CONTROLLER ........................................................................ 57 4.9.1 GENERAL FEATURES .................................................................................................................... 57 4.9.2 ELECTRICAL BEHAVIOR OF MAGNETIC INTERRUPT PINS ................................................................... 58 4.9.3 DATA READY / DRDY INTERRUPT .................................................................................................. 58 4.9.4 LOW-THRESHOLD INTERRUPT........................................................................................................ 59 4.9.5 HIGH-THRESHOLD INTERRUPT ....................................................................................................... 60 4.9.6 OVERFLOW .................................................................................................................................. 61 5. FIFO OPERATION.................................................................................................................... 62 5.1 FIFO OPERATING MODES ................................................................................................. 62 5.2 FIFO DATA READOUT ....................................................................................................... 63 5.3 FIFO FRAME COUNTER AND OVERRUN FLAG ..................................................................... 63 5.4 FIFO INTERRUPTS ............................................................................................................ 64 6. ACCELEROMETER REGISTER DESCRIPTION.................................................................... 65 6.1 GENERAL REMARKS .......................................................................................................... 65 6.2 REGISTER MAP ................................................................................................................. 66 6.3 CHIP ID ............................................................................................................................ 67 6.4 ACCELERATION DATA ........................................................................................................ 68 6.5 TEMPERATURE DATA ......................................................................................................... 72 6.6 STATUS REGISTERS .......................................................................................................... 73 6.7 G-RANGE SELECTION ......................................................................................................... 77 6.8 BANDWIDTHS .................................................................................................................... 78 6.9 POWER MODES ................................................................................................................. 79 6.10 SPECIAL CONTROL SETTINGS ........................................................................................... 81 6.11 INTERRUPT SETTINGS ...................................................................................................... 83 6.12 SELF-TEST ..................................................................................................................... 96 6.13 NON-VOLATILE MEMORY CONTROL (EEPROM)................................................................. 97 6.14 INTERFACE CONFIGURATION ............................................................................................ 98 6.15 OFFSET COMPENSATION.................................................................................................. 99 6.16 NON-VOLATILE MEMORY BACK-UP .................................................................................. 102 6.17 FIFO CONFIGURATION AND FIFO DATA .......................................................................... 103 7. MAGNETOMETER REGISTER DESCRIPTION ................................................................... 105 7.1 GENERAL REMARKS ........................................................................................................ 105 7.2 REGISTER MAP ............................................................................................................... 105 7.3 CHIP ID .......................................................................................................................... 106 7.4 MAGNETIC FIELD DATA .................................................................................................... 106 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 6 7.5 INTERRUPT STATUS REGISTER ......................................................................................... 109 7.6 POWER AND OPERATION MODES, SELF-TEST AND DATA OUTPUT RATE CONTROL REGISTERS 110 7.7 INTERRUPT AND AXIS ENABLE SETTINGS CONTROL REGISTERS ........................................... 112 7.8 NUMBER OF REPETITIONS CONTROL REGISTERS ............................................................... 114 8. DIGITAL INTERFACES .......................................................................................................... 116 8.1 SERIAL PERIPHERAL INTERFACE (SPI) .............................................................................. 117 8.2 INTER-INTEGRATED CIRCUIT (IC) .................................................................................... 121 8.2.1 SPI AND IC ACCESS RESTRICTIONS .......................................................................................... 126 9. PIN-OUT AND CONNECTION DIAGRAM............................................................................. 127 9.1 PIN-OUT ......................................................................................................................... 127 9.2 CONNECTION DIAGRAM 4-WIRE SPI ................................................................................. 128 9.3 CONNECTION DIAGRAM 3-WIRE SPI ................................................................................. 129 9.4 CONNECTION DIAGRAM I2C .............................................................................................. 130 10. PACKAGE ............................................................................................................................ 131 10.1 OUTLINE DIMENSIONS.................................................................................................... 131 10.2 SENSING AXES ORIENTATION ......................................................................................... 132 10.3 ANDROID AXES ORIENTATION ......................................................................................... 133 10.4 LANDING PATTERN RECOMMENDATION ........................................................................... 135 10.5 MARKING...................................................................................................................... 136 10.5.1 MASS PRODUCTION DEVICES .................................................................................................... 136 10.5.2 ENGINEERING SAMPLES ............................................................................................................ 136 10.6 SOLDERING GUIDELINES ................................................................................................ 137 10.7 HANDLING INSTRUCTIONS .............................................................................................. 138 10.8 TAPE AND REEL SPECIFICATION...................................................................................... 139 10.8.1 TAPE AND REEL DIMENSIONS..................................................................................................... 139 10.8.2 ORIENTATION WITHIN THE REEL................................................................................................. 139 10.9 ENVIRONMENTAL SAFETY .............................................................................................. 140 10.9.1 HALOGEN CONTENT ................................................................................................................. 140 10.9.2 INTERNAL PACKAGE STRUCTURE ............................................................................................... 140 11. LEGAL DISCLAIMER........................................................................................................... 141 11.1 ENGINEERING SAMPLES................................................................................................. 141 11.2 PRODUCT USE .............................................................................................................. 141 11.3 APPLICATION EXAMPLES AND HINTS ............................................................................... 141 12. DOCUMENT HISTORY AND MODIFICATION ................................................................... 142 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 7 1. Specification If not stated otherwise, the given values are over lifetime and full performance temperature and voltage ranges, minimum/maximum values are 3. The specifications are split into accelerometer part and magnetometer part of BMC150. 1.1 Compass electrical specification Table 1: Compass electrical parameter specification Compass Operating Conditions Parameter Supply Voltage Internal Domains Supply Voltage I/O Domain Voltage Input Low Level Voltage Input High Level Voltage Output Low Level Voltage Output High Level Symbol Condition Min Typ Max Unit VDD 1.62 2.4 3.6 V VDDIO 1.2 1.8 3.6 V 0.3VDDIO - VIL,a SPI & IC VIH,a SPI & IC VOL VOH BST-BMC150-DS000-04 | Revision 1.0 | July 2014 VDDIO = 1.2V IOL = 3mA, SPI & IC VDDIO = 1.62V IOH = 2mA, SPI & IC 0.7VDDIO 0.2VDDIO 0.8VDDIO - Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 8 1.2 Accelerometer specification Table 2: Accelerometer parameter specification ACCELEROMETER Operating Conditions Parameter Symbol Condition Acceleration Range gFS2g gFS4g gFS8g gFS16g Selectable via serial digital interface 2 4 8 16 g g g g Total Supply Current in Normal Mode IDD TA=25C, bw = 1kHz VDD = VDDIO = 2.4V 130 A IDDlp1 TA=25C, bw = 1kHz VDD = VDDIO = 2.4V 6.5 A TA=25C, bw = 1kHz VDD = VDDIO = 2.4V 66 A Total Supply Current in Low-Power Mode 1 Total Supply Current in Low-Power Mode 2 Min Typ Max Unit sleep duration = 25ms IDDlp2 sleep duration = 25ms Total Supply Current in Deep Suspend Mode IDDsm,a TA=25C VDD = VDDIO = 2.4V 1 A Total Supply Current in Suspend Mode IDDsum TA=25C VDD = VDDIO = 2.4V 2.1 A Total Supply Current in Standby Mode IDDsbm TA=25C VDD = VDDIO = 2.4V 62 A Wake-Up Time 1 tw_up,a1 Wake-Up Time 2 tw_up,a2 Start-Up Time ts_up,a Non-volatile memory (NVM) write-cycles nNVM BST-BMC150-DS000-04 | Revision 1.0 | July 2014 from Low-power Mode 1 or Suspend Mode or Deep Suspend Mode bw = 1kHz from Low-power Mode 2 or Stand-by Mode bw = 1kHz POR, bw = 1kHz 1.3 1.8 ms 1.0 1.2 s 3 ms 15 cycles Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Operating Temperature Same for accelerometer and magnetometer TA Page 9 -40 +85 C Max Unit ACCELEROMETER OUTPUT SIGNAL Parameter Device Resolution Symbol Condition Dres,a gFS2g 0.98 mg Sensitivity S2g S4g S8g S16g 1024 512 256 128 LSB/g LSB/g LSB/g LSB/g Sensitivity Temperature Drift TCSa 0.02 %/K Zero-g Offset Off 80 mg Zero-g Offset Temperature Drift TCO gFS2g, TA=25C gFS4g, TA=25C gFS8g, TA=25C gFS16g, TA=25C gFS2g, Nominal VDD supplies gFS2g, TA=25C, nominal VDD supplies, over life-time gFS2g, Nominal VDD supplies 1 mg/K Bandwidth bw8 bw16 bw31 bw63 bw125 bw250 bw500 bw1000 2nd order filter, bandwidth programmable 8 16 31 63 125 250 500 1000 Hz Hz Hz Hz Hz Hz Hz Hz Nonlinearity NL,a best fit straight line, gFS2g 0.5 %FS Output Noise Density nrms,a gFS2g, TA=25C Nominal VDD supplies Normal mode 150 g/Hz BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Min Typ Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Temperature Sensor Measurement Range1 Page 10 TS -40 85 C Temperature Sensor Slope1 dTS 0.5 K/LSB Temperature Sensor Offset1 OTS 2 K ACCELEROMETER MECHANICAL CHARACTERISTICS 1 Parameter Symbol Cross Axis Sensitivity Sa Alignment Error EA,a Condition relative contribution between any two of the three axes relative to package outline Min Typ Max Unit 1 % 0.5 Tentative value BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 11 1.3 Magnetometer specification Table 3: Magnetometer Parameter Specification MAGNETOMETER Operating Conditions Parameter Symbol Condition Magnetic field range Brg,xy Brg,z TA=25C2 Magnetometer heading accuracy 3 Acheading System heading accuracy4 Asheading IDD,lp,m Supply Current in Active Mode (average)5 IDD,rg,m IDD,eh,m IDD,ha,m Supply Current in Suspend Mode IDDsm,m Peak supply current in Active Mode IDDpk,m Peak logic supply current in active mode IDDIOpk,m 30T horizontal geomagnetic field component, TA=25C 30T horizontal geomagnetic field component, TA=25C Low power preset Nominal VDD supplies TA=25C, ODR=10Hz Regular preset Nominal VDD supplies TA=25C, ODR=10Hz Enhanced regular preset Nominal VDD supplies TA=25C, ODR=10Hz High accuracy preset Nominal VDD supplies TA=25C, ODR=20Hz Nominal VDD/VDDIO supplies, TA=25C In measurement phase Nominal VDD supplies TA=25C Only during measurement phase Nominal VDDIO supplies TA=25C Min Typ Max 1300 2500 Unit T T 2.5 degree 3.0 degree 170 A 0.5 mA 0.8 mA 4.9 mA 1 A 18 mA 210 A 2 Full linear measurement range considering sensor offsets. The heading accuracy depends both on hardware and software. For detailed information of the software performance please contact Bosch Sensortec. 4 Heading accuracy of the tilt-compensated 6-axis eCompass system, assuming calibration with Bosch Sensortec eCompass software (only available for Android and Windows operating sytems and requires the conclusion of a software licence agreement). Average value over various device orientations (typical device usage). 5 For details on magnetometer current consumption calculation refer to chapter 4.2.2 and 4.2.3. 3 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 POR time tw_up,m Start-Up Time ts_up,m BST-BMC150-DS000-04 | Revision 1.0 | July 2014 from OFF to Suspend; time starts when VDD>1.5V and VDDIO>1.1V from Suspend to sleep Page 12 1.0 ms 3.0 ms Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 13 MAGNETOMETER OUTPUT SIGNAL Parameter Device Resolution Gain error 6 Symbol Condition Dres,m TA=25C Gerr,m Min After API temperature compensation TA=25C Nominal VDD supplies After API temperature compensation -40C TA +85C Nominal VDD supplies Typ Max Unit 0.3 T 2 % 0.01 %/K Sensitivity Temperature Drift TCSm Zero-B offset OFFm TA=25C 40 T Zero-B offset OFFm,cal After software calibration with Bosch Sensortec eCompass software7 -40C TA +85C 2 T Zero-B offset Temperature Drift TCOm -40C TA +85C Nominal VDD supplies 0.07 T/K odrlp Low power preset 10 Hz odrrg Regular preset 10 Hz odreh Enhanced regular preset 10 Hz odrha High accuracy preset 20 Hz odrlp Low power preset 0 >300 Hz odrrg Regular preset Enhanced regular preset 0 100 Hz 0 60 Hz odrha High accuracy preset 0 20 Hz Full-scale Nonlinearity NLm, FS best fit straight line 1 %FS Output Noise nrms,lp,m,xy Low power preset x, y-axis, TA=25C Nominal VDD supplies ODR (data output rate), normal mode ODR (data output rate), forced mode odreh 1.0 T 6 Definition: gain error = ( (measured field after API compensation) / (applied field) ) - 1 Magnetic zero-B offset assuming calibration with Bosch Sensortec eCompass software (only available for Android and Windows operating sytems and requires the conclusion of a software licence agreement). Typical value after applying calibration movements containing various device orientations (typical device usage). 7 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 nrms,lp,m,z nrms,rg,m nrms,eh,m nrms,ha,m Power Supply Rejection Rate PSRRm BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Low power preset z-axis, TA=25C Nominal VDD supplies Regular preset TA=25C Nominal VDD supplies Enhanced regular preset TA=25C Nominal VDD supplies High accuracy preset TA=25C Nominal VDD supplies TA=25C Nominal VDD supplies Page 14 1.4 T 0.6 T 0.5 T 0.3 T 0.5 T/V Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 15 2. Absolute maximum ratings The absolute maximum ratings provided in Table 4 apply to both the accelerometer and magnetometer part of BMC150. At or above these maximum ratings operability is not given. The specification limits in Chapter 1 only apply under normal operating conditions. Table 4: Absolute maximum ratings Parameter Condition Min Max Unit VDD Pin -0.3 4.0 V VDDIO Pin -0.3 4.0 V Voltage at any Logic Pad Non-Supply Pin -0.3 Operating Temperature, TA Passive Storage Temp. Range Active operation 65% rel. H. -40 -50 None-volatile memory (NVM) Data Retention T = 85C, after 15 cycles 10 Voltage at Supply Pin Mechanical Shock ESD Magnetic field Duration 200s Duration 1.0ms Free fall onto hard surfaces HBM, at any Pin CDM MM Any direction VDDIO + 0.3 +85 +150 V C C year 10,000 2,000 g g 1.8 m 2 500 200 >7 kV V V T Note: Stress above these limits may cause damage to the device. Exceeding the specified limits may affect the device reliability or cause malfunction. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 16 3. Block diagram Figure 1 shows the basic building blocks of the BMC150: Accelerometer MEMS VDD VDD Accelerometer ASIC GND GND X VDDIO Vref PS a INT1 Regulator Y M U X Gain & Offset C/U ADC Logic Z NVM Osc I n t e r f a c e VDDIO INT2 PS1 SDI INT1 SDO INT2 SCK SDI CSB SDO INT3 SCK DRDY CSB1 FlipCores VDD Magnetometer ASIC X Vref X, Y FlipCore Y GND Regulator Drive & Sense ADC VDDIO Logic Z Hall element Drive & Sense NVM Osc I n t e r f a c e PS2 INT3 DRDY SDI SDO SCK CSB2 Figure 1: Block diagram of BMC150 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 17 4. Functional description BMC150 is a SiP (system in package) integration of a triaxial accelerometer (Sensing element and ASIC) and a triaxial geomagnetic sensor (Sensing element and ASIC) in one package. The two ASICs act as two separate slave devices on the digital bus (with different IC address in IC mode), which allows an independent operation of accelerometer and magnetometer parts in order to fit into a wide range of usage scenarios. 4.1 Supply voltage and power management The BMC150 has two distinct power supply pins which supply both the acceleration sensor part and the magnetometer sensor part: * VDD is the main power supply for all internal analog and digital functional blocks; * VDDIO is a separate power supply pin, used for the supply of the digital interface as well as the magnetic sensor's logic. There are no limitations on the voltage levels of both pins relative to each other, as long as each of them lies within its operating range. Furthermore, the device can be completely switched off (VDD = 0V) while keeping the VDDIO supply within operating range or vice versa. It is absolutely prohibited to keep any interface at a logical high level when V DDIO is switched off. Such a configuration will permanently damage the device (i.e. if VDDIO = 0 [SDI & SDO & SCK & CSB] high). The device contains a power on reset (POR) generator for each of the sensor parts, accelerometer part and magnetometer part. It resets the logic part and the register values of the concerned ASIC after powering-on VDD and VDDIO. Please note, that all application specific settings which are not equal to the default settings (refer to register maps chapter 6.2 and 7.2 ), must be re-set to its designated values after POR. There are no constraints on the sequence of switching on both supply voltages. In case the IC interface is used, a direct electrical connection between VDDIO supply and the PS pin is needed in order to ensure reliable protocol selection. For SPI interface mode the PS pin must be directly connected to GND. 4.2 Power modes The BMC150 features separately configurable power modes for the accelerometer and the magnetometer part. The advantage is that different characteristics regarding optimum system power saving of the two sensor types are exploited, and that the accelerometer part may also be used alone in certain usage scenarios where no magnetic field data is required. In such an example, the magnetometer part is able to suspend and save power during the time in which it is not required. In the following chapters, power modes for both accelerometer and magnetometer part are described. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 18 4.2.1 Accelerometer power modes The BMC150 accelerometer part has six different power modes (see Figure 2). Besides normal mode, which represents the fully operational state of the device, there are five energy saving modes: deep-suspend mode, suspend mode, standby mode, low-power mode 1 and low-power mode 2. The possible transitions between the power modes are illustrated in Figure 2 : DEEPSUSPEND Mode SUSPEND Mode NORMAL Mode Low Power Mode 1 STANDBY Mode Low Power Mode 2 Figure 2: Power mode transition diagram After power-up the accelerometer part of BMC150 is in normal mode so that this part is held powered-up and data acquisition is performed continuously. In deep-suspend mode the device reaches the lowest possible power consumption. Only the interface section is kept alive. No data acquisition is performed and the content of the configuration registers is lost. Deep suspend mode is entered (left) by writing `1' (`0') to the (0x11) deep_suspend bit while (0x11) suspend bit is set to `0'. The I2C watchdog timer remains functional. The (0x11) deep_ suspend bit, the (0x34) spi3 bit, (0x34) i2c_wdt_en bit and the (0x34) i2c_wdt_sel bit are functional in deep-suspend mode. Equally the interrupt level and driver configuration registers (0x20) int1_lvl, (0x20) int1_od, (0x20) int2_lvl, and (0x20) int2_od are accessible. Still it is possible to enter normal mode by performing a softreset as described in chapter 4.8. Please note, that all application specific settings which are not equal to the default settings (refer to 6.2), must be re-set to its designated values after leaving deep-suspend mode. In suspend mode the whole analog part is powered down. No data acquisition is performed. While in suspend mode the latest acceleration data and the content of all configuration registers are kept. Writing to and reading from registers is supported except from the (0x3E) BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 19 fifo_config_1, (0x30) fifo_config_0 and (0x3F) fifo_data register. It is possible to enter normal mode by performing a softreset as described in chapter.7.6. Suspend mode is entered (left) by writing 1 (0) to the (0x11) suspend bit after bit (0x12) lowpower_mode has been set to `0'. Although write access to registers is supported at the full interface clock speed (SCL or SCK), a waiting period must be inserted between two consecutive write cycles (please refer also to section 8.2.1). In standby mode the analog part is powered down, while the digital part remains largely operational. No data acquisition is performed. Reading and writing registers is supported without any restrictions. The latest acceleration data and the content of all configuration registers are kept. Standby mode is entered (left) by writing 1 (0) to the (0x11) suspend bit after bit (0x12) lowpower_mode has been set to `1'. It is also possible to enter normal mode by performing a softreset as described in chapter 7.6. In low-power mode 1, the device is periodically switching between a sleep phase and a wakeup phase. The wake-up phase essentially corresponds to operation in normal mode with complete power-up of the circuitry. The sleep phase essentially corresponds to operation in suspend mode. Low-power mode is entered (left) by writing 1 (0) to the (0x11) lowpower_en bit after bit (0x12) lowpower_mode has been set to `0'. Read access to registers is possible except from the (0x3F) fifo_data register. However, unless the register access is synchronised with the wake-up phase, the restrictions of the suspend mode apply. Low-power mode 2 is very similar to low-power mode 1, but register access is possible at any time without restrictions. It consumes more power than low-power mode 1. In low-power mode 2 the device is periodically switching between a sleep phase and a wake-up phase. The wake-up phase essentially corresponds to operation in normal mode with complete power-up of the circuitry. The sleep phase essentially corresponds to operation in standby mode. Low-power mode is entered (left) by writing 1 (0) to the (0x11) lowpower_en bit with bit (0x12) lowpower_mode set to `1'. The timing behaviour of the low-power modes 1 and 2 depends on the setting of the (0x12) sleeptimer_mode bit. When (0x12) sleeptimer_mode is set to `0', the event-driven time-base mode (EDT) is selected. In EDT the duration of the wake-up phase depends on the number of samples required by the enabled interrupt engines. If an interrupt is detected, the device stays in the wake-up phase as long as the interrupt condition endures (non-latched interrupt), or until the latch time expires (temporary interrupt), or until the interrupt is reset (latched interrupt). If no interrupt is detected, the device enters the sleep phase immediately after the required number of acceleration samples have been taken and an active interface access cycle has ended. The EDT mode is recommended for power-critical applications which do not use the FIFO. Also, EDT mode is compatible with legacy BST sensors. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 20 Figure 3 shows the timing diagram for low-power modes 1 and 2 when EDT is selected. Settle Sample Sample Sample Settle Sample Sleep phase Settle Sample Sample Active phase Sample tACTIVE State tSLEEP tSLEEP t Figure 3: Timing Diagram for low-power mode 1/2, EDT When (0x12) sleeptimer_mode is set to `1', the equidistant-sampling mode (EST) is selected. The use of the EST mode is recommended when the FIFO is used since it ensures that equidistant samples are sampled into the FIFO regardless of whether the active phase is extended by active interrupt engines or interface activity. In EST mode the sleep time tSLEEP,a is defined as shown in Figure 4. The FIFO sampling time tSAMPLE,a is the sum of the sleep time tSLEEP,a and the sensor data sampling time tSSMP,a. Since interrupt engines can extend the active phase to exceed the sleep time tSLEEP,a, equidistant sampling is only guaranteed if the bandwidth has been chosen such that 1/(2 * bw) = n * tSLEEP,a where n is an integer. If this condition is infringed, equidistant sampling is not possible. Once the sleep time has elapsed the device will store the next available sample in the FIFO. This set-up condition is not recommended as it may result in timing jitter. Sampled into FIFO tSLEEP tSSMP tSAMPLE tSLEEP tSAMPLE Settle Sample Settle Sample Sample Sample Settle Sample Sleep phase Settle Sample Sample Active phase Sample State tSLEEP tSAMPLE t Figure 4: Timing Diagram for low-power mode 1/2, EST BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 21 The sleep time for lower-power mode 1 and 2 is set by the (0x11) sleep_dur bits as shown in the following table: Table 5: Sleep phase duration settings (0x11) sleep_dur Sleep Phase Duration tSLEEP,a 0000b 0001b 0010b 0011b 0100b 0101b 0110b 0111b 1000b 1001b 1010b 1011b 1100b 1101b 1110b 1111b 0.5ms 0.5ms 0.5ms 0.5ms 0.5ms 0.5ms 1ms 2ms 4ms 6ms 10ms 25ms 50ms 100ms 500ms 1s The current consumption of the BMC150 accelerometer part in low-power mode 1 (IDDlp1) and low-power mode 2 (IDDlp2) can be estimated with the following formulae: I DDlp1,a I DDlp 2,a t sleep,a I DDsum,a t active,a I DD ,a t sleep,a t active,a t sleep,a I DDsbm,a t active,a I DD ,a t sleep,a t active,a When estimating the length of the wake-up phase tactive, the corresponding typical wake-up time, tw,up1 or tw,up2 and tut (given in table 5) have to be considered: If bandwidth is >=31.25 Hz: tactive = tut + tw,up1 - 0.9 ms (or tactive = tut + tw,up2 - 0.9 ms) else: tactive = 4 tut + tw,up1 - 0.9 ms (or tactive = 4 tut + tw,up2 - 0.9 ms) During the wake-up phase all analog modules are held powered-up, while during the sleep phase most analog modules are powered down. Consequently, a wake-up time of at least tw,up1 (tw,up2) is needed to settle the analog modules so that reliable acceleration data are generated. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 22 4.2.2 Magnetometer power modes The BMC150 magnetometer part features configurable power modes. The four power modes of the BMC150 magnetometer are decribed in the following chapters. Power off mode In Power off mode, VDD and/or VDDIO are unpowered. The magnetometer part does not operate in this mode. When only one of VDD or VDDIO is supplied, the magnetic sensor will still be in Power off mode. Power on reset is performed after both VDD and VDDIO have risen above their detection thresholds. Suspend mode Suspend mode is the default power mode of BMC150 magnetometer part after the chip is powered. When VDD and VDDIO are turned on the POR (power on reset) circuits operate and the device's registers are initialized. After POR becomes inactive, a start up sequence is executed. In this sequence NVM content is downloaded to shadow registers located in the device core. After the start up sequence the device is put in the Suspend mode. In this mode only registers which store power control bit information and SPI 3 wire enable can be accessed by the user. In this mode only registers supplied directly by VDDIO which store I2C slave device address, power control bit information and some others can be accessed by the user. No other registers can be accessed in Suspend mode. All registers loose their content, except the control register (0x4B). In particular, in this mode a Chip ID read (register 0x40) returns "0x00" (IC) or high-Z (SPI). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 23 Sleep mode The user puts device from suspend into Sleep mode by setting the Power bit to "1", or from active modes (normal or forced) by setting OpMode bits to "11". In this state the user has full access to the device registers. In particular, the Chip ID can be read. Setting the power control bit to "0" (register 0x4B bit0) will bring the device back into Suspend mode. From the Sleep mode the user can put the device back into Suspend mode or into Active mode. Active mode The device can switch into Active mode from Sleep mode by setting OpMode bits (register 0x4C). In active mode the magnetic field measurements are performed. In active mode, all registers are accessible. In active mode, two operation modes can be distinguished: Normal mode: selected channels are periodically measured according to settings set in user registers. After measurements are completed, output data is put into data registers and the device waits for the next measurement period, which is set by programmed output data rate (ODR). From normal mode, the user can return to sleep mode by setting OpMode to "11" or by performing a soft reset (see chapter 7.6). Suspend mode can be entered by setting power control bit to "0". Forced mode (single measurement): When set by the host, the selected channels are measured according to settings programmed in user registers. After measurements are completed, output data is put into data registers, OpMode register value returns to "11" and the device returns to sleep mode. The forced mode is useful to achieve synchronized operation between host microcontroller and BMC150. Also, different data output rates from the ones selectable in normal mode can be achieved using forced mode. Figure 5: Magnetometer power mode transition diagram In Active Mode and normal operation, in principle any desired balance between output noise and active time (hence power consumption) can be adjusted by the repetition settings for x/yaxis and z-axis and the output data rate ODR. The average power consumption depends on the ratio of high current phase time (during data acquisition) and low current phase time (between BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 24 data acquisitions). Hence, the more repetitions are acquired to generate one magnetic field data point, the longer the active time ratio in one sample phase, and the higher the average current. Thanks to longer internal averaging, the noise level of the output data reduces with increasing number of repetitions. By using forced mode, it is possible to trigger new measurements at any rate. The user can therefore trigger measurements in a shorter interval than it takes for a measurement cycle to complete. If a measurement cycle is not allowed to complete, the resulting data will not be written into the data registers. To prevent this, the manually triggered measurement intervals must not be shorter than the active measurement time which is a function of the selected number of repetitions. The maximum selectable read-out frequency in forced mode can be calculated as follows: f max,ODR 1 145s nXY 500s nZ 980s Hereby nXY is the number of repetitions on X/Y-axis (not the register value) and nZ the number of repetitions on Z-axis (not the register value) (see description of XY_REP and Z_REP registers in chapter 7). Although the repetition numbers for X/Y and Z axis and the ODR can be adjusted independently and in a wide range, there are four recommended presets (High accuracy preset, Enhanced regular preset, Regular preset, Low power preset) which reflect the most common usage scenarios, i.e. required output accuracy at a given current consumption, of the BMC150 magnetometer part. The four presets consist of the below register configurations, which are automatically set by the BMC150 API or driver provided by Bosch Sensortec when a preset is selected. Table 6 shows the recommended presets and the resulting magnetic field output noise and magnetometer part current consumption: Table 6: Magnetometer presets in Active operation and normal mode: Preset Low power preset Regular preset Enhanced regular preset High accuracy preset X/Y rep Z rep ODR ODRmax (forced mode) RMS Noise x/y/z Average current consumption 3 3 10 Hz >300 Hz 1.0/1.0/1.4 T 170 A 9 15 10 Hz 100 Hz 0.6/0.6/0.6 T 0.5 mA 15 27 10 Hz 60 Hz 0.5/0.5/0.5 T 0.8 mA 47 83 20 Hz 20 Hz 0.3/0.3/0.3 T 4.9 mA BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 25 4.2.3 BMC150 overall power consumption Below, Table 7 shows the overall current consumption of BMC150 (sum of accelerometer and magnetometer part) in typical scenarios such as a tilt-compensated electronic compass application. Table 7: BMC150 overall current consumption in typical usage scenarios: Compass preset Low power preset Regular preset Enhanced regular preset High accuracy preset Acc. Active / sleep interval Acc. BW / DOR Mag. Avg. current Acc. avg. current Total average current 8 / 50 ms 62.5 / 17 Hz 170 A 20 A 190 A 16 / 50 ms 31 / 15 Hz 0.5 mA 35 A 0.54 mA 16 / 50 ms 31 / 15 Hz 0.8 mA 35 A 0.84 mA 16 /25 ms 31 / 24 Hz 4.9 mA 55 A 5.0 mA BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 26 4.3 Sensor data 4.3.1 Acceleration data The width of acceleration data is 12 bits given in twos complement representation. The 12 bits for each axis are split into an MSB upper part (one byte containing bits 11 to 4) and an LSB lower part (one byte containing bits 3 to 0 of acceleration and a (0x02, 0x04, 0x06) new_data flag). Reading the acceleration data registers shall always start with the LSB part. In order to ensure the integrity of the acceleration data, the content of an MSB register is locked by reading the corresponding LSB register (shadowing procedure). When shadowing is enabled, the MSB must always be read in order to remove the data lock. The shadowing procedure can be disabled (enabled) by writing 1 (0) to the bit shadow_dis. With shadowing disabled, the content of both MSB and LSB registers is updated by a new value immediately. Unused bits of the LSB registers may have any value and should be ignored. The (0x02, 0x04, 0x06) new_data flag of each LSB register is set if the data registers have been updated. The flag is reset if either the corresponding MSB or LSB part is read. Two different streams of acceleration data are available, unfiltered and filtered. The unfiltered data is sampled with 2kHz. The sampling rate of the filtered data depends on the selected filter bandwidth and is always twice the selected bandwidth (BW = ODR/2). Which kind of data is stored in the acceleration data registers depends on bit (0x13) data_high_bw. If (0x13) data_high_bw is 0 (1), then filtered (unfiltered) data is stored in the registers. Both data streams are offset-compensated. The bandwidth of filtered acceleration data is determined by setting the (0x10) bw bit as followed: Table 8: Bandwidth configuration bw Bandwidth Update Time tut 00xxx 01000 01001 01010 01011 01100 01101 01110 01111 1xxxx *) 7.81Hz 15.63Hz 31.25Hz 62.5Hz 125Hz 250Hz 500Hz 1000Hz *) 64ms 32ms 16ms 8ms 4ms 2ms 1ms 0.5ms - *) Note: Settings 00xxx result in a bandwidth of 7.81 Hz; settings 1xxxx result in a bandwidth of 1000 Hz. It is recommended to actively use the range from 01000b to 01111b only in order to be compatible with future products. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 27 The BMC150's accelerometer part supports four different acceleration measurement ranges. A measurement range is selected by setting the (0x0F) range bits as follows: Table 9: Range selection Range Acceleration measurement range Resolution 0011 0101 1000 1100 others 2g 4g 8g 16g reserved 0.98mg/LSB 1.95mg/LSB 3.91mg/LSB 7.81mg/LSB - 4.3.2 Temperature sensor The width of temperature data is 8 bits given in twos complement representation. Temperature values are available in the (0x08) temp register. The slope of the temperature sensor is 0.5K/LSB, its center temperature is 23C [(0x08) temp = 0x00]. 4.3.3 Magnetic field data The representation of magnetic field data is different between X/Y-axis and Z-axis. The width of X- and Y-axis magnetic field data is 13 bits each and stored in two's complement. DATAX_LSB (0x42) contains 5-bit LSB part [4:0] of the 13 bit output data of the X-channel. DATAX_MSB (0x43) contains 8-bit MSB part [12:5] of the 13 bit output data of the X-channel. DATAY_LSB (0x44) contains 5-bit LSB part [4:0] of the 13 bit output data of the Y-channel. DATAY_MSB (0x45) contains 8-bit MSB part [12:5] of the 13 bit output data of the Y-channel. The width of the Z-axis magnetic field data is 15 bit word stored in two's complement. DATAZ_LSB (0x46) contains 7-bit LSB part [6:0] of the 15 bit output data of the Z-channel. DATAZ_MSB (0x47) contains 8-bit MSB part [14:7] of the 15 bit output data of the Z-channel. For all axes, temperature compensation on the host is used to get ideally matching sensitivity over the full temperature range. The temperature compensation is based on a resistance measurement of the hall sensor plate. The resistance value is represented by a 14 bit unsigned output word. RHALL_LSB (0x48) contains 6-bit LSB part [5:0] of the 14 bit output data of the RHALLchannel. RHALL_MSB (0x49) contains 8-bit MSB part [13:6] of the 14 bit output data of the RHALLchannel. All signed register values are in twos complement representation. Bits which are marked "reserved" can have different values or can in some cases not be read at all (read will return 0x00 in IC mode and high-Z in SPI mode). Data register readout and shadowing is implemented as follows: BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 28 After all enabled axes have been measured, complete data packages consisting of DATAX, DATAY, DATAZ and RHALL are updated at once in the data registers. This way, it is prevented that a following axis is updated while the first axis is still being read (axis mix-up) or that MSB part of an axis is updated while LSB part is being read. While reading from any data register, data register update is blocked. Instead, incoming new data is written into shadow registers which will be written to data registers after the previous read sequence is completed (i.e. upon stop condition in IC mode, or CSB going high in SPI mode, respectively). Hence, it is recommended to read out at all data at once (0x42 to 0x49 or 0x4A if status bits are also required) with a burst read. Single bytes or axes can be read out, while in this case it is not assured that adjacent registers are not updated during readout sequence. The "Data ready status" bit (register 0x48 bit0) is set "1" when the data registers have been updated but the data was not yet read out over digital interface. Data ready is cleared (set "0") directly after completed read out of any of the data registers and subsequent stop condition (IC) or lifting of CSB (SPI). In addition, when enabled the "Data overrun" bit (register 0x4A bit7) turns "1" whenever data registers are updated internally, but the old data was not yet read out over digital interface (i.e. data ready bit was still high). The "Data overrun" bit is cleared when the interrupt status register 0x4A is read out. This function needs to be enabled separately by setting the "Data overrun En" bit (register 0x4D bit7)). Note: Please also see chapter 7 for detailed register descriptions. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 29 4.3.4 Magnetic field data temperature compensation The raw register values DATAX, DATAY, DATAZ and RHALL are read out from the host processor using the BMC150 API/driver which is provided by Bosch Sensortec. The API/driver performs an off-chip temperature compensation and outputs x/y/z magnetic field data in 16 LSB/T to the upper application layer: Software application level Application Config Software driver level BMC150 API / driver (provided by Bosch Sensortec) Config Hardware level Temperature compensated magnetic field data x/y/z in signed int, (16 LSB/T) or float Magnetometer raw register data (DATAX, DATAY, DATAZ, RHALL) BMC150 sensor Figure 6: Calculation flow of magnetic field data from raw BMC150 register data The API/driver performs all calculations using highly optimized fixed-point C-code arithmetic. For platforms that do not support C code, a floating-point formula is available as well. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 30 4.4 Self-test 4.4.1 Accelerometer self-test This feature permits to check the BMC150's accelerometer part functionality by applying electrostatic forces to the sensor core instead of external accelerations. By actually deflecting the seismic mass, the entire signal path of the sensor can be tested. Activating the self-test results in a static offset of the acceleration data; any external acceleration or gravitational force applied to the sensor during active self-test will be observed in the output as a superposition of both acceleration and self-test signal. Before the self-test is enabled the g-range should be set to 8 g.The self-test is activated individually for each axis by writing the proper value to the (0x32) self_test_axis bits (01b for xaxis, 10b for y-axis, 11b for z-axis, 00b to deactivate self-test). It is possible to control the direction of the deflection through bit (0x32) self_test_sign. The excitation occurs in negative (positive) direction if (0x32) self_test_sign = 0b (1b). The amplitude of the deflection has to be set high by writing (0x32) self_test_amp=1b. After the self-test is enabled, the user should wait 50ms before interpreting the acceleration data. In order to ensure a proper interpretation of the self-test signal it is recommended to perform the self-test for both (positive and negative) directions and then to calculate the difference of the resulting acceleration values. Table 10 shows the minimum differences for each axis. The actually measured signal differences can be significantly larger. Table 10: Self-test difference values x-axis signal resulting minimum difference signal 800 mg y-axis signal 800 mg z-axis signal 400 mg It is recommended to perform a reset of the device after a self-test has been performed. If the reset cannot be performed, the following sequence must be kept to prevent unwanted interrupt generation: disable interrupts, change parameters of interrupts, wait for at least 50ms, enable desired interrupts. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 31 4.4.2 Magnetometer self-test BMC150 supports two self-tests modes for the magnetometer part: Normal self-test and advanced self-test. Normal self test During normal self-test, the following verifications are performed: FlipCore signal path is verified by generating signals on-chip. These are processed through the signal path and the measurement result is compared to known thresholds. FlipCore (X and Y) bondwires to ASIC are checked for connectivity FlipCore (X and Y) bondwires and MEMS are checked for shorts Hall sensor connectivity is checked for open and shorted connections Hall sensor signal path and hall sensor element offset are checked for overflow. To perform a self test, the sensor must first be put into sleep mode (OpMode = "11"). Self-test mode is then entered by setting the bit "Self test" (register 0x4C bit0) to "1". After performing self test, this bit is set back to "0". When self-test is successful, the corresponding self-test result bits are set to "1" ("X-Self-Test" register 0x42 bit0, "Y-Self-Test" register 0x44 bit0, "Z-Self-Test" register 0x46 bit0). If self-test fails for an axis, the corresponding result bit returns "0". Advanced self test Advanced self test performs a verification of the Z channel signal path functionality and sensitivity. An on-chip coil wound around the hall sensor can be driven in both directions with a calibrated current to generate a positive or negative field of around 100 T. Advanced self test is an option that is active in parallel to the other operation modes. The only difference is that during the active measurement phase, the coil current is enabled. The recommended usage of advanced self test is the following: 1. Set sleep mode 2. Disable X, Y axis 3. Set Z repetitions to desired level 4. Enable positive advanced self test current 5. Set forced mode, readout Z and R channel after measurement is finished 6. Enable negative advanced self test current 7. Set forced mode, readout Z and R channel after measurement is finished 8. Disable advanced self test current (this must be done manually) 9. Calculate difference between the two compensated field values. This difference should be around 200 T with some margins. 10. Perform a soft reset of manually restore desired settings Please refer to the corresponding application note for the exact thresholds to evaluate advanced self-test. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 32 Below table describes how the advanced self-test is controlled: Table 11: Magnetometer advanced self-test control (0x4C) Adv.ST <1:0> 00b 01b 10b 11b Configuration Normal operation (no self-test), default Reserved, do not use Negative on-chip magnetic field generation Positive on-chip magnetic field generation The BMC150 API/driver provided by Bosch Sensortec provides a comfortable way to perform both self-tests and to directly obtain the result without further calculations. It is recommended to use this as a reference. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 33 4.5 Accelerometer offset compensation Offsets in measured acceleration signals can have several causes but they are always unwanted and disturbing in many cases. Therefore, the accelerometer part of BMC150 offers an advanced set of four digital offset compensation methods which are closely matched to each other. These are slow, fast, and manual compensation, and inline calibration. The compensation is performed with unfiltered data, and is then applied to both, unfiltered and filtered data. If necessary the result of this computation is saturated to prevent any overflow errors (the smallest or biggest possible value is set, depending on the sign). However, the registers used to read and write compensation values have only a width of 8 bits. An overview of the offset compensation principle is given in Figure 7: I2C/SPI/NVM mapping 12 bit acceleration data range +-16g +-8g +-4g 8g Sign 4g 4g Sign 2g 2g 2g Sign 1g 1g 1g 1g 500mg 500mg 500mg 500mg 500mg 250mg 250mg 250mg 250mg 250mg 125mg 125mg 125mg 125mg 125mg 62.5mg 62.5mg 62.5mg 62.5mg 31.2mg 31.2mg 31.2mg 31.2mg 31.2mg 15.6mg 15.6mg 15.6mg 15.6mg 15.6mg 7.8mg 7.8mg 7.8mg 7.8mg 3.9mg 3.9mg MSB Read/ Write 62.5mg LSB Sign Sign +-2g MSB MSB - 1.9mg LSB MSB LSB MSB LSB LSB 7.8mg 3.9mg 1.9mg 0.97mg Figure 7: Principle of offset compensation BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 34 The public offset compensation registers (0x38) offset_x, (0x39) offset_y, (0x3A) offset_z are images of the corresponding registers in the NVM. With each image update (see section 4.6 for details) the contents of the NVM registers are written to the public registers. The public register can be over-written by the user at any time. After changing the contents of the public registers by either an image update or manually, all 8bit values are extended to 12bit values for internal computation. In the opposite direction, if an internally computed value changes it is converted to an 8bit value and stored in the public register. Depending on the selected g-range the conversion from 12bit to 8bit values can result in a loss of accuracy of one to several LSB. This is shown in Figure 7. In case an internally computed compensation value is too small or too large to fit into the corresponding register, it is saturated in order to prevent an overflow error. By writing 1 to the (0x36) offset_reset bit, all offset compensation registers are reset to zero. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 35 4.5.1 Slow compensation Slow compensation is based on a 1st order high-pass filter, which continuously drives the average value of the output data stream of each axis to zero. The bandwidth of the high-pass filter is configured with bit (0x37) cut_off according to . Table 12: Compensation period settings (0x37) cut_off high-pass filter bandwidth Example bw = 500 Hz 0b 1b *bw: please insert selected decimal data bandwidth value [Hz] from table 8 The slow compensation can be enabled (disabled) for each axis independently by setting the bits (0x36) hp_x_en, hp_y_en, hp_z_en to 1 (0), respectively. Slow compensation should not be used in combination with low-power mode. In low-power mode the conditions (availability of necessary data) for proper function of slow compensation are not fulfilled. 4.5.2 Fast compensation Fast compensation is a one-shot process by which the compensation value is set in such a way that when added to the raw acceleration, the resulting acceleration value of each axis approches the target value. This is best suited for "end-of-line trimming" with the customer's device positioned in a well-defined orientation. For fast compensation the g-range has to be switched to 2g. The algorithm in detail: An average of 16 consecutive acceleration values is computed and the difference between target value and computed value is written to (0x38, 0x39, 0x3A) offset_filt_x/y/z. The public registers (0x38, 0x39, 0x3A) offset_filt_x/y/z are updated with the contents of the internal registers (using saturation if necessary) and can be read by the user. Fast compensation is triggered for each axis individually by setting the (0x36) cal_trigger bits as shown in Table 13: Table 13: Fast compensation axis selection (0x36) cal_trigger Selected Axis 00b 01b 10b 11b none x y z BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 36 Register (0x36) cal_trigger is a write-only register. Once triggered, the status of the fast correction process is reflected in the status bit (0x36) cal_rdy. Bit (0x36) cal_rdy is `0' while the correction is in progress. Otherwise it is `1'. Bit (0x36) cal_rdy is 0 when (0x36) cal_trigger is not 00. For the fast offset compensation, the compensation target can be chosen by setting the bits (0x37) offset_target_x, (0x37) offset_target_y, and (0x37) offset_target_z according to Table 14: Table 14: Offset target settings (0x37) offset_target_x/y/z 00b 01b 10b 11b Target value 0g +1g -1g 0g Fast compensation should not be used in combination with any of the low-power modes. In lowpower mode the conditions (availability of necessary data) for proper function of fast compensation are not fulfilled. 4.5.3 Manual compensation The contents of the public compensation registers (0x38, 0x39, 0x3A) offset_filt_x/y/z can be set manually via the digital interface. It is recommended to write into these registers directly after a new data interrupt has occurred in order not to disturb running offset computations. Writing to the offset compensation registers is not allowed while the fast compensation procedure is running. 4.5.4 Inline calibration For certain applications, it is often desirable to calibrate the offset once and to store the compensation values permanently. This can be achieved by using one of the aforementioned offset compensation methods to determine the proper compensation values and then storing these values permanently in the NVM. See chapter 4.6.1 for details of the storing procedure. Each time the device is reset, the compensation values are loaded from the non-volatile memory into the image registers and used for offset compensation until they are possibly overwritten using one of the other compensation methods. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 37 4.6 Non-volatile memory 4.6.1 Accelerometer non-volatile memory The memory of the accelerometer part of BMC150 consists of three different kinds of registers: hard-wired, volatile, and non-volatile. Part of it can be both read and written by the user. Access to non-volatile memory is only possible through (volatile) image registers. Altogether, there are eight registers (octets) with NVM backup which are accessible by the user. The addresses of the image registers range from 0x38 to 0x3C. While the addresses up to 0x3A are used for offset compensation (see section 4.5), addresses 0x3B and 0x3C are general purpose registers not linked to any sensor-specific functionality. The content of the NVM is loaded to the image registers after a reset (either POR or soft reset) or after a user request which is performed by writing 1 to the write-only bit (0x33) nvm_load. As long as the image update is in progress, bit (0x33) nvm_rdy is 0, otherwise it is 1. The image registers can be read and written like any other register. Writing to the NVM is a three-step procedure: 1. Write the new contents to the image registers. 2. Write 1 to bit (0x33) nvm_prog_mode in order to unlock the NVM. 3. Write 1 to bit (0x33) nvm_prog_trig and keep 1 in bit (0x33) nvm_prog_mode in order to trigger the write process. Writing to the NVM always renews the entire NVM contents. It is possible to check the write status by reading bit (0x33) nvm_rdy. While (0x33) nvm_rdy = 0, the write process is still in progress; if (0x33) nvm_rdy = 1, then writing is completed. As long as the write process is ongoing, no change of power mode and image registers is allowed. Also, the NVM write cycle must not be initiated while image registers are updated, in low-power mode, and in suspend mode. Please note that the number of permitted NVM write-cycles is limited as specified in Table 2. The number of remaining write-cycles can be obtained by reading bits (0x33) nvm_remain. 4.6.2 Magnetometer non-volatile memory Some of the memory of the BMC150 magnetometer is non-volatile memory (NVM). This NVM is pre-programmed in Bosch Sensortec fabrication line and cannot be modified afterwards. It contains trimming data which are required for sensor operation and sensor data compensation, thus it is read out by the BMC150 API/driver during initialization. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 38 4.7 Accelerometer interrupt controller The accelerometer part of BMC150 is equipped with eight programmable interrupt engines. Each interrupt can be independently enabled and configured. If the trigger condition of an enabled interrupt is fulfilled, the corresponding status bit is set to 1 and the selected interrupt pin is activated. There are two interrupt pins for the accelerometer part, INT1 and INT2; interrupts can be freely mapped to any of these pins. The state of a specific interrupt pin is derived from a logic or combination of all interrupts mapped to it. The interrupt status registers are updated when a new data word is written into the acceleration data registers. If an interrupt is disabled, all active status bits associated with it are immediately reset. 4.7.1 General features An interrupt is cleared depending on the selected interrupt mode, which is common to all interrupts. There are three different interrupt modes: non-latched, latched, and temporary. The mode is selected by the (0x21) latch_int bits according to Table 15. Table 15 : Accelerometer interrupt mode selection (0x21) atch_int Interrupt mode 0000b 0001b 0010b 0011b 0100b 0101b 0110b 0111b 1000b 1001b 1010b 1011b 1100b 1101b 1110b 1111b non-latched temporary, 250ms temporary, 500ms temporary, 1s temporary, 2s temporary, 4s temporary, 8s latched non-latched temporary, 250s temporary, 500s temporary, 1ms temporary, 12.5ms temporary, 25ms temporary, 50ms latched An interrupt is generated if its activation condition is met. It cannot be cleared as long as the activation condition is fulfilled. In the non-latched mode the interrupt status bit and the selected pin (the contribution to the or condition for INT1 and/or INT2) are cleared as soon as the activation condition is no more valid. Exceptions to this behavior are the new data, orientation, and flat interrupts, which are automatically reset after a fixed time. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 39 In latched mode an asserted interrupt status and the selected pin are cleared by writing 1 to bit (0x21) reset_int. If the activation condition still holds when it is cleared, the interrupt status is asserted again with the next change of the acceleration registers. In the temporary mode an asserted interrupt and selected pin are cleared after a defined period of time. The behavior of the different interrupt modes is shown graphically in Figure 8. The timings in this mode are subject to the same tolerances as the bandwidths (see Table 2). internal signal from interrupt engine interrupt output non-latched latch period temporary latched Figure 8: Interrupt modes Several interrupt engines can use either unfiltered or filtered acceleration data as their input. For these interrupts, the source can be selected with the bits in register (0x1E). These are (0x1E) int_src_data, (0x1E) int_src_tap, (0x1E) int_src_slo_no_mot, (0x1E) int_src_slope, (0x1E) int_src_high, and (0x1E) int_src_low. Setting the respective bits to 0 (1) selects filtered (unfiltered) data as input. The orientation recognition and flat detection interrupt always use filtered input data. It is strongly recommended to set interrupt parameters prior to enabling the interrupt. Changing parameters of an already enabled interrupt may cause unwanted interrupt generation and generation of a false interrupt history. A safe way to change parameters of an enabled interrupt is to keep the following sequence: disable the desired interrupt, change parameters, wait for at least 10ms, and then re-enable the desired interrupt. 4.7.2 Mapping to physical interrupt pins (inttype to INT Pin#) Registers (0x19) to (0x1B) are dedicated to mapping of interrupts to the interrupt pins "INT1" or "INT2". Setting (0x19) int1_"inttype" to 1 (0) maps (unmaps) "inttype" to pin "INT1". Correspondingly setting (0x1B) int2_"inttype" to 1 (0) maps (unmaps) "inttype" to pin "INT2". Note: "inttype" to be replaced with the precise notation, given in the memory map in chapter 5. Example: For flat interrupt (int1_flat): Setting (0x19) int1_flat to 1 maps int1_flat to pin "INT1". BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 40 4.7.3 Electrical behavior (INT pin# to open-drive or push-pull) Both interrupt pins can be configured to show the desired electrical behavior. The active level of each interrupt pin is determined by the (0x20) int1_lvl and (0x20) int2_lvl bits. If (0x20) int1_lvl = 1 (0) / (0x20) int2_lvl = 1 (0), then pin "INT1" / pin "INT2" is active 1 (0). The characteristic of the output driver of the interrupt pins may be configured with bits (0x20) int1_od and (0x20) int2_od. By setting bits (0x20) int1_od / (0x20) int2_od to 1, the output driver shows open-drive characteristic, by setting the configuration bits to 0, the output driver shows push-pull characteristic. When open-drive characteristic is selected in the design, external pull-up or pull-down resistor should be applied according the int_lvl configuration. 4.7.4 New data interrupt This interrupt serves for synchronous reading of acceleration data. It is generated after storing a new value of z-axis acceleration data in the data register. The interrupt is cleared automatically when the next data acquisition cycle starts. The interrupt status is 0 for at least 50s. The interrupt mode of the new data interrupt is fixed to non-latched. It is enabled (disabled) by writing 1 (0) to bit (0x17) data_en. The interrupt status is stored in bit (0x0A) data_int. Due to the settling time of the filter, the first interrupt after wake-up from suspend or standby mode will take longer than the update time BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 41 4.7.5 Slope / any-motion detection Slope / any-motion detection uses the slope between successive acceleration signals to detect changes in motion. An interrupt is generated when the slope (absolute value of acceleration difference) exceeds a preset threshold. It is cleared as soon as the slope falls below the threshold. The principle is made clear in Figure 9. acceleration acc(t0) acc(t0-1/(2*bw)) time slope(t0)=acc(t0)-acc(t0-1/(2*bw)) slope slope_th time slope_dur slope_dur INT time Figure 9: Principle of any-motion detection The threshold is defined through register (0x28) slope_th. In terms of scaling 1 LSB of (0x28) slope_th corresponds to 3.91 mg in 2g-range (7.81 mg in 4g-range, 15.6 mg in 8g-range and 31.3 mg in 16g-range). Therefore the maximum value is 996 mg in 2g-range (1.99g in 4g-range, 3.98g in 8g-range and 7.97g in 16g-range). The time difference between the successive acceleration signals depends on the selected bandwidth and equates to 1/(2*bandwidth) (t=1/(2*bw)). In order to suppress false triggers, the interrupt is only generated (cleared) if a certain number N of consecutive slope data points is larger (smaller) than the slope threshold given by (0x28) slope_th. This number is set by the (0x27) slope_dur bits. It is N = (0x27) slope_dur + 1 for (0x27). Example: (0x27) slope_dur = 00b, ..., 11b = 1decimal, ..., 4decimal. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 42 4.7.5.1 Enabling (disabling) for each axis Any-motion detection can be enabled (disabled) for each axis separately by writing 1 (0) to bits (0x16) slope_en_x, (0x16) slope_en_y, (0x16) slope_en_z. The criteria for any-motion detection are fulfilled and the slope interrupt is generated if the slope of any of the enabled axes exceeds the threshold (0x28) slope_th for [(0x27) slope_dur +1] consecutive times. As soon as the slopes of all enabled axes fall or stay below this threshold for [(0x27) slope_dur +1] consecutive times the interrupt is cleared unless interrupt signal is latched. 4.7.5.2 Axis and sign information of slope / any motion interrupt The interrupt status is stored in bit (0x09) slope_int. The any-motion interrupt supplies additional information about the detected slope. The axis which triggered the interrupt is given by that one of bits (0x0B) slope_first_x, (0x0B) slope_first_y, (0x0B) slope_first_z that contains a value of 1. The sign of the triggering slope is held in bit (0x0B) slope_sign until the interrupt is retriggered. If (0x0B) slope_sign = 0 (1), the sign is positive (negative). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 43 4.7.6 Tap sensing Tap sensing has a functional similarity with a common laptop touch-pad or clicking keys of a computer mouse. A tap event is detected if a pre-defined slope of the acceleration of at least one axis is exceeded. Two different tap events are distinguished: A `single tap' is a single event within a certain time, followed by a certain quiet time. A `double tap' consists of a first such event followed by a second event within a defined time frame. Single tap interrupt is enabled (disabled) by writing "1" ("0") to bit (0x16) s_tap_en. Double tap interrupt is enabled (disabled) by writing "1" ("0") to bit (0x16) d_tap_en. While temporary latching is used do not simultaneously enable single tap interrupt and double tap interrupt. The status of the single tap interrupt is stored in bit (0x09) s_tap_int, the status of the double tap interrupt is stored in bit (0x09) d_tap_int. The slope threshold for detecting a tap event is set by bits (0x2B) tap_th. The meaning of (0x2B) tap_th depends on the range setting. 1 LSB of (0x2B) tap_th corresponds to a slope of 62.5mg in 2g-range, 125mg in 4g-range, 250mg in 8g-range, and 500mg in 16g-range. In Figure 10 the meaning of the different timing parameters is visualized: slope 1st tap 2nd tap tap_th time a tap_shock tap_quiet tap_dur tap_shock tap_quiet single tap detection 12.5 ms time double tap detection 12.5 ms time Figure 10: Timing of tap detection BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 44 The parameters (0x2A) tap_shock and (0x2A) tap_quiet apply to both single tap and double tap detection, while (0x2A) tap_dur applies to double tap detection only. Within the duration of (0x2A) tap_shock any slope exceeding (0x2B) tap_th after the first event is ignored. Contrary to this, within the duration of (0x2A) tap_quiet no slope exceeding (0x2B) tap_th must occur, otherwise the first event will be cancelled. 4.7.6.1 Single tap detection A single tap is detected and the single tap interrupt is generated after the combined durations of (0x2A) tap_shock and (0x2A) tap_quiet, if the corresponding slope conditions are fulfilled. The interrupt is cleared after a delay of 12.5 ms. Do not map single-tap to any INT pin if you do not want to use it. 4.7.6.2 Double tap detection A double tap interrupt is generated if an event fulfilling the conditions for a single tap occurs within the set duration in (0x2A) tap_dur after the completion of the first tap event. The interrupt is automatically cleared after a delay of 12.5 ms. 4.7.6.3 Selecting the timing of tap detection For each of parameters (0x2A) tap_shock and (0x2A) tap_quiet two values are selectable. By writing 0 (1) to bit (0x2A) tap_shock the duration of (0x2A) tap_shock is set to 50 ms (75 ms). By writing 0 (1) to bit (0x2A) tap_quiet the duration of (0x2A) tap_quiet is set to 30 ms (20 ms). The length of (0x2A) tap_dur can be selected by setting the (0x2A) tap_dur bits according to Table 16: Table 16: Selection of tap_dur (0x2A) tap_dur length of tap_dur 000b 001b 010b 011b 100b 101b 110b 111b 50 ms 100 ms 150 ms 200 ms 250 ms 375 ms 500 ms 700 ms BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 45 4.7.6.4 Axis and sign information of tap sensing The sign of the slope of the first tap which triggered the interrupt is stored in bit (0x0B) tap_sign (0 means positive sign, 1 means negative sign). The value of this bit persists after clearing the interrupt. The axis which triggered the interrupt is indicated by bits (0x0B) tap_first_x, (0x0B) tap_first_y, and (0x0B) tap_first_z. The bit corresponding to the triggering axis contains a 1 while the other bits hold a 0. These bits are cleared together with clearing the interrupt status. 4.7.6.5 Tap sensing in low power mode In low-power mode, a limited number of samples is processed after wake-up to decide whether an interrupt condition is fulfilled. The number of samples is selected by bits (0x2B) tap_samp according to Table 17. Table 17: Meaning of (0x2B) tap_samp (0x2B) tap_samp Number of Samples 00b 01b 10b 11b 2 4 8 16 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 46 4.7.7 Orientation recognition The orientation recognition feature informs on an orientation change of the sensor with respect to the gravitational field vector `g'. The measured acceleration vector components with respect to the gravitational field are defined as shown in Figure 11. Figure 11: Definition of vector components Therefore, the magnitudes of the acceleration vectors are calculated as follows: acc_x = 1g x sin x cos acc_y = -1g x sin x sin acc_z = 1g x cos acc_y/acc_x = -tan Depending on the magnitudes of the acceleration vectors the orientation of the device in the space is determined and stored in the three (0x0C) orient bits. These bits may not be reset in the sleep phase of low-power mode. There are three orientation calculation modes with different thresholds for switching between different orientations: symmetrical, high-asymmetrical, and low-asymmetrical. The mode is selected by setting the (0x2C) orient_mode bits as given in Table 18. Table 18: Orientation mode settings (0x2C) orient_mode Orientation Mode 00b 01b 10b 11b symmetrical high-asymmetrical low-asymmetrical symmetrical BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 47 For each orientation mode the (0x0C) orient bits have a different meaning as shown in Table 19 to Table 21: Table 19: Meaning of the (0x0C) orient bits in symmetrical mode (0x0C) orient Name Angle Condition x00 portrait upright 315 < < 45 |acc_y| < |acc_x| - `hyst' and acc_x - `hyst'' 0 x01 portrait upside down 135 < < 225 |acc_y| < |acc_x| - `hyst' and acc_x + `hyst' < 0 x10 landscape left 45 < < 135 |acc_y| |acc_x| + `hyst' and acc_y < 0 x11 landscape right 225 < < 315 |acc_y| |acc_x| + `hyst' and acc_y 0 Table 20: Meaning of the (0x0C) orient bits in high-asymmetrical mode (0x0C) orient Name Angle Condition x00 portrait upright 297 < < 63 |acc_y| < 2|acc_x| - `hyst' and acc_x - `hyst' 0 x01 portrait upside down 117 < < 243 |acc_y| < 2|acc_x| - `hyst' and acc_x + `hyst' < 0 x10 landscape left 63 < < 117 |acc_y| 2|acc_x| + `hyst' and acc_y < 0 x11 landscape right 243 < < 297 |acc_y| 2|acc_x| + `hyst' and acc_y 0 Table 21: Meaning of the (0x0C) orient bits in low-asymmetrical mode (0x0C) orient Name Angle Condition x00 portrait upright 333 < < 27 |acc_y| < 0.5|acc_x| - `hyst' and acc_x - `hyst' 0 x01 portrait upside down 153 < < 207 |acc_y| < 0.5|acc_x| - `hyst' and acc_x + `hyst' < 0 x10 landscape left 27 < < 153 x11 landscape right 207 < < 333 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 |acc_y| 0.5|acc_x| + `hyst' and acc_y < 0 |acc_y| 0.5|acc_x| + `hyst' and acc_y 0 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 48 In the preceding tables, the parameter `hyst' stands for a hysteresis, which can be selected by setting the (0x2C) orient_hyst bits. 1 LSB of (0x2C) orient_hyst always corresponds to 62.5 mg, in any g-range (i.e. increment is independent from g-range setting). It is important to note that by using a hysteresis 0 the actual switching angles become different from the angles given in the tables since there is an overlap between the different orientations. The most significant bit of the (0x0C) orient bits (which is displayed as an x in the above given tables) contains information about the direction of the z-axis. It is set to 0 (1) if acc_z 0 (acc_z < 0). Figure 12 shows the typical switching conditions between the four different orientations for the symmetrical mode i.e. without hysteresis: portrait portraitupright upright landscape left portrait portraitupside upside down landscape landscaperight right portrait upright 2 1.5 1 0.5 0 0 45 90 135 180 225 270 315 360 -0.5 acc_y/acc_x -1 acc_x/sin(theta) -1.5 acc_y/sin(theta) -2 phi Figure 12: Typical orientation switching conditions w/o hysteresis The orientation interrupt is enabled (disabled) by writing 1 (0) to bit (0x16) orient_en. The interrupt is generated if the value of (0x0C) orient has changed. It is automatically cleared after one stable period of the (0x0C) orient value. The interrupt status is stored in the (0x09) orient_int bit. The register (0x0C) orient always reflects the current orientation of the device, irrespective of which interrupt mode has been selected. Bit (0x0C) orient<2> reflects the device orientation with respect to the z-axis. The bits (0x0C) orient<1:0> reflect the device orientation in the x-y-plane. The conventions associated with register (0x0C) orient are detailed in chapter 5. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 49 4.7.7.1 Orientation blocking The change of the (0x0C) orient value and - as a consequence - the generation of the interrupt can be blocked according to conditions selected by setting the value of the (0x2C) orient_blocking bits as described by Table 22. Table 22: Blocking conditions for orientation recognition (0x2C) orient_blocking Conditions 00b no blocking theta blocking or acceleration in any axis > 1.5g theta blocking or acceleration slope in any axis > 0.2 g or acceleration in any axis > 1.5g theta blocking or acceleration slope in any axis > 0.4 g or acceleration in any axis > 1.5g and value of orient is not stable for at least 100 ms 01b 10b 11b The theta blocking is defined by the following inequality: tan blocking _ theta . 8 The parameter blocking_theta of the above given equation stands for the contents of the (0x2D) orient_theta bits. It is possible to define a blocking angle between 0 and 44.8. The internal blocking algorithm saturates the acceleration values before further processing. As a consequence, the blocking angles are strictly valid only for a device at rest; they can be different if the device is moved. Example: To get a maximum blocking angle of 19 the parameter blocking_theta is determined in the following way: (8 * tan(19) ) = 7.588, therefore, blocking_value = 8dec = 001000b has to be chosen. In order to avoid unwanted generation of the orientation interrupt in a nearly flat position (z ~ 0, sign change due to small movements or noise), a hysteresis of 0.2 g is implemented for the zaxis, i. e. a after a sign change the interrupt is only generated after |z| > 0.2 g. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 50 4.7.7.2 Up-Down Interrupt Suppression Flag Per default an orientation interrupt is triggered when any of the bits in register (0x0C) orient changes state. The BMA255 can be configured to trigger orientation interrupts only when the device position changes in the x-y-plane while orientation changes with respect to the z-axis are ignored. A change of the orientation of the z-axis, and hence a state change of bit (0x0C) orient<2> is ignored (considered) when bit (0x2D) orient_ud_en is set to `0' (`1'). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 51 4.7.8 Flat detection The flat detection feature gives information about the orientation of the devices z-axis relative to the g-vector, i. e. it recognizes whether the device is in a flat position or not. The flat angle is adjustable by (0x2E) flat_theta from 0 to 44.8. The flat angle can be set according to following formula: 1 atan flat_theta 8 A hysteresis of the flat detection can be enabled by (0x2F) flat_hy bits. In this case the flat position is set if the angle drops below following threshold: 1 flat _ hy flat _ hy hyst,ll atan flat_theta 1 8 1024 16 The flat position is reset if the angle exceeds the following threshold: 1 flat _ hy flat _ hy hyst,ul atan flat_theta 1 8 1024 16 The flat interrupt is enabled (disabled) by writing 1 (0) to bit (0x16) flat_en. The flat value is stored in the (0x0C) flat bit if the interrupt is enabled. This value is 1 if the device is in the flat position, it is 0 otherwise. The flat interrupt is generated if the flat value has changed and the new value is stable for at least the time given by the (0x2F) flat_hold_time bits. A flat interrupt may be also generated if the flat interrupt is enabled. The actual status of the interrupt is stored in the (0x09) flat_int bit. The flat orientation of the sensor can always be determined from reading the (0x0C) flat bit after interrupt generation. If unlatched interrupt mode is used, the (0x09) flat_int value and hence the interrupt is automatically cleared after one sample period. If temporary or latched interrupt mode is used, the (0x09) flat_int value is kept fixed until the latch time expires or the interrupt is reset. The meaning of the (0x2F) flat_hold_time bits can be seen from Table 23. Table 23: Meaning of flat_hold_time (0x2F) flat_hold_time Time 00b 01b 10b 11b 0 512 ms 1024 ms 2048 ms BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 52 4.7.9 Low-g interrupt This interrupt is based on the comparison of acceleration data against a low-g threshold, which is most useful for free-fall detection. The interrupt is enabled (disabled) by writing "1" ("0") to the (0x17) low_en bit. There are two modes available, `single' mode and `sum' mode. In `single' mode, the acceleration of each axis is compared with the threshold; in `sum' mode, the sum of absolute values of all accelerations |acc_x| + |acc_y| + |acc_z| is compared with the threshold. The mode is selected by the contents of the (0x24) low_mode bit: "0" means `single' mode, "1" means `sum' mode. The low-g threshold is set through the (0x23) low_th register. 1 LSB of (0x23) low_th always corresponds to an acceleration of 7.81 mg (i.e. increment is independent from g-range setting). A hysteresis can be selected by setting the (0x24) low_hy bits. 1 LSB of (0x24) low_hy always corresponds to an acceleration difference of 125 mg in any g-range (as well, increment is independent from g-range setting). The low-g interrupt is generated if the absolute values of the acceleration of all axes (and relation, in case of single mode) or their sum (in case of sum mode) are lower than the threshold for at least the time defined by the (0x22) low_dur register. The interrupt is reset if the absolute value of the acceleration of at least one axis (or relation, in case of single mode) or the sum of absolute values (in case of sum mode) is higher than the threshold plus the hysteresis for at least one data acquisition. In bit (0x09) low_int the interrupt status is stored. The relation between the content of (0x22) low_dur and the actual delay of the interrupt generation is: delay [ms] = [(0x22) low_dur + 1] * 2 ms. Therefore, possible delay times range from 2 ms to 512 ms. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 53 4.7.10 High-g interrupt This interrupt is based on the comparison of acceleration data against a high-g threshold for the detection of shock or other high-acceleration events. The high-g interrupt is enabled (disabled) per axis by writing "1" ("0") to bits (0x17) high_en_x, (0x17) high_en_y, and (0x17) high_en_z, respectively. The high-g threshold is set through the (0x26) high_th register. The meaning of an LSB of (0x26) high_th depends on the selected grange: it corresponds to 7.81 mg in 2g-range, 15.63 mg in 4g-range, 31.25 mg in 8g-range, and 62.5 mg in 16g-range (i.e. increment depends from g-range setting). A hysteresis can be selected by setting the (0x24) high_hy bits. Analogously to (0x26) high_th, the meaning of an LSB of (0x24) high_hy is g-range dependent: it corresponds to an acceleration difference of 125 mg in 2g-range, 250 mg in 4g-range, 500 mg in 8g-range, and 1000mg in 16g-range (as well, increment depends from g-range setting). The high-g interrupt is generated if the absolute value of the acceleration of at least one of the enabled axes (or relation) is higher than the threshold for at least the time defined by the (0x25) high_dur register. The interrupt is reset if the absolute value of the acceleration of all enabled axes (and relation) is lower than the threshold minus the hysteresis for at least the time defined by the (0x25) high_dur register. In bit (0x09) high_int the interrupt status is stored. The relation between the content of (0x25) high_dur and the actual delay of the interrupt generation is delay [ms] = [(0x22) low_dur + 1] * 2 ms. Therefore, possible delay times range from 2 ms to 512 ms. The interrupt will be cleared immediately once acceleration is lower than threshold. 4.7.10.1 Axis and sign information of high-g interrupt The axis which triggered the interrupt is indicated by bits (0x0C) high_first_x, (0x0C) high_first_y, and (0x0C) high_first_z. The bit corresponding to the triggering axis contains a "1" while the other bits hold a "0". These bits are cleared together with clearing the interrupt status. The sign of the triggering acceleration is stored in bit (0x0C) high_sign. If (0x0C) high_sign = "0" ("1"), the sign is positive (negative). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 54 4.7.11 No-motion / slow motion detection The slow-motion/no-motion interrupt engine can be configured in two modes. In slow-motion mode an interrupt is triggered when the measured slope of at least one enabled axis exceeds the programmable slope threshold for a programmable number of samples. Hence the engine behaves similar to the any-motion interrupt, but with a different set of parameters. In order to suppress false triggers, the interrupt is only generated (cleared) if a certain number N of consecutive slope data points is larger (smaller) than the slope threshold given by (0x27) slo_no_mot_dur<1:0>. The number is N = (0x27) slo_no_mot_dur<1:0> + 1. In no-motion mode an interrupt is generated if the slope on all selected axes remains smaller than a programmable threshold for a programmable delay time. Figure 13 shows the timing diagram for the no-motion interrupt. The scaling of the threshold value is identical to that of the slow-motion interrupt. However, in no-motion mode register (0x27) slo_no_mot_dur defines the delay time before the no-motion interrupt is triggered. Table 24 lists the delay times adjustable with register (0x27) slo_no_mot_dur. The timer tick period is 1 second. Hence using short delay times can result in considerable timing uncertainty. If bit (0x18) slo_no_mot_sel is set to `1' (`0') the no-motion/slow-motion interrupt engine is configured in the no-motion (slow-motion) mode. Common to both modes, the engine monitors the slopes of the axes that have been enabled with bits (0x18) slo_no_mot_en_x, (0x18) slo_no_mot_en_y, and (0x18) slo_no_mot_en_z for the x-axis, y-axis and z-axis, respectively. The measured slope values are continuously compared against the threshold value defined in register (0x29) slo_no_mot_th. The scaling is such that 1 LSB of (0x29) slo_no_mot_th corresponds to 3.91 mg in 2g-range (7.81 mg in 4g-range, 15.6 mg in 8g-range and 31.3 mg in 16g-range). Therefore the maximum value is 996 mg in 2g-range (1.99g in 4g-range, 3.98g in 8g-range and 7.97g in 16g-range). The time difference between the successive acceleration samples depends on the selected bandwidth and equates to 1/(2 * bw). Table 24: No-motion time-out periods (0x27) slo_no_mot_dur 0 1 2 ... 14 15 Delay time 1s 2s 3s ... 15 s 16 s (0x27) slo_no_mot_dur 16 17 18 19 20 21 Delay time 40 s 48 s 56 s 64 s. 72 s 80 s (0x27) slo_no_mot_dur 32 33 34 ... 62 63 Delay Time 88 s 96 s 104 s ... 328 s 336 s Note: slo_no_mot_dur values 22 to 31 are not specified BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 acceleration Page 55 acc(t0+t) acc(t0) slope axis x, y, or z slope(t0+t)= acc(t0+t) - acc(t0) axis x, y, or z slo_no_mot_th -slo_no_mot_th slo_no_mot_dur timer INT time Figure 13: Timing of No-motion interrupt BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 56 4.8 Accelerometer softreset A softreset causes all user configuration settings to be overwritten with their default value and the sensor to enter normal mode. A softreset is initiated by means of writing value 0xB6 to register (0x14) softreset. Subsequently a waiting time of tw,up1 (max.) is required prior to accessing any configuration registers. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 57 4.9 Magnetometer interrupt controller Four magnetometer based interrupt engines are integrated in the magnetometer part of BMC150: Low-Threshold, High-Threshold, Overflow and Data Ready (DRDY). Each interrupt can be enabled independently. When enabled, an interrupt sets the corresponding status bit in the interrupt status register (0x4A) when its condition is satisfied. When the "Interrupt Pin Enable" bit (register 0x4E bit6) is set, any occurring activated interrupts are flagged on the BMC150's INT3 output pin. By default, the interrupt pin is disabled (high-Z status). Low-Threshold, High-Threshold and Overflow interrupts are mapped to the INT3 pin when enabled, Data Ready (DRDY) interrupt is mapped to the DRDY pin of BMC150 when enabled. For High- and Low-Threshold interrupts each axis X/Y/Z can be enabled separately for interrupt detection in the registers "High Int Z en", "High Int Y en", "High Int X en", "Low Int Z en", "Low Int Y En" and "Low Int X En" in register 0x4D bit5-bit0. Overflow interrupt is shared for X, Y and Z axis. When the "Data Ready Pin En" bit (register 0x4E bit7) is set, the Data Ready (DRDY) interrupt event is flagged on the BMC150's DRDY output pin (by default the "Data Ready Pin En" bit is not set and DRDY pin is in high-Z state). The interrupt status registers are updated together with writing new data into the magnetic field data registers. The status bits for Low-/High-Threshold interrupts are located in register 0x4A, the Data Ready (DRDY) status flag is located at register 0x48 bit0. If an interrupt is disabled, all active status bits and pins are reset after the next measurement was performed. 4.9.1 General features An interrupt is cleared depending on the selected interrupt mode, which is common to all interrupts. There are two different interrupt modes: non-latched and latched. All interrupts (except Data Ready) can be latched or non-latched. Data Ready (DRDY) is always cleared after readout of data registers ends. A non-latched interrupt will be cleared on a new measurement when the interrupt condition is not valid anymore, whereas a latched interrupt will stay high until the interrupts status register (0x4A) is read out. After reading the interrupt status, both the interrupt status bits and the interrupt pin are reset. The mode is selected by the "Interrupt latch" bit (register 0x4A bit1), where the default setting of "1" means latched. Figure 14 shows the difference between the modes for the example Low-Threshold interrupt. INT3 and DRDY pin polarity can be changed by the "Interrupt polarity" bit (register 0x4E bit0) and "DR polarity" (register 0x4E bit2), from the default high active ("1") to low active ("0"). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 58 Low threshold measurements INT3 pin (non-latched) INT3 pin (latched) Readings of interrupt status register (0x4A) Figure 14: Interrupt latched and non-latched mode 4.9.2 Electrical behavior of magnetic interrupt pins Both interrupt pins INT3 and DRDY are push/pull when the corresponding interrupt pin enable bit is set, and are floating (High-Z) when the corresponding interrupt pin enable bit is disabled (default). 4.9.3 Data ready / DRDY interrupt This interrupt serves for synchronous reading of magnetometer data. It is generated after storing a new set of values (DATAX, DATAY, DATAZ, RHALL) in the data registers: Active measurement time Inactive time Data write into output registers Preset time Measurement Measurement Data Dataprocessing processing DRDY ='1 ' Measurement phase start Data readout Figure 15: Data acquisition and DRDY operation (DRDY in "high active" polarity) The interrupt mode of the Data Ready (DRDY) interrupt is fixed to non-latched. It is enabled (disabled) by writing "1" ("0") to "Data Ready pin En" in register 0x4E bit7. DRDY pin polarity can be changed by the "DR polarity" bit (register 0x4E bit2), from the default high active ("1") to low active ("0"). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 59 4.9.4 Low-threshold interrupt When the data registers' (DATAX, DATAY and DATAZ) values drop below the threshold level defined by the "Low Threshold register (0x4F), the corresponding interrupt status bits for those axes are set ("Low Int X", "Low Int Y" and "Low Int Z" in register 0x4A). This is done for each axis independently. Please note that the X and Y axis value for overflow is -4096. However, no interrupt is generated on these values. See chapter 4.9.6 for more information on overflow. Hereby, one bit in "Low Threshold" corresponds to roughly 6T (not exactly, as the raw magnetic field values DATAX, DATAY and DATAZ are not temperature compensated). The Low-threshold interrupt is issued on INT3 pin when one or more values of the data registers DATAX, DATAY and DATAZ drop below the threshold level defined by the "Low Threshold" register (0x4F), and when the axis where the threshold was exceeded is enabled for interrupt generation: Result = (DATAX < "Low Threshold" x 16) AND "Low Int X en" is "0" OR (DATAY < "Low Threshold" x 16) AND "Low Int Y en" is "0" OR (DATAZ < "Low Threshold" x 16) AND "Low Int Z en" is "0" Note: Threshold interrupt enable bits ("Low INT [XYZ] en") are active low and "1" (disabled) by default. Low threshold a a measurements INT3 pin (non-latched) INT3 pin (latched) Read interrupt status register (0x4A) Figure 16: Low-threshold interrupt function BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 60 4.9.5 High-threshold interrupt When the data registers' (DATAX, DATAY and DATAZ) values exceed the threshold level defined by the "High Threshold register (0x50), the corresponding interrupt status bits for those axes are set ("High Int X", "High Int Y" and "High Int Z" in register 0x4A). This is done for each axis independently. Hereby, one bit in "High Threshold" corresponds to roughly 6T (not exactly, as the raw magnetic field values DATAX, DATAY and DATAZ are not temperature compensated). The High-threshold interrupt is issued on INT3 pin when one or more values of the data registers DATAX, DATAY and DATAZ exceed the threshold level defined by the "High Threshold" register (0x50), and when the axis where the threshold was exceeded is enabled for interrupt generation: Result = (DATAX > "High Threshold" x 16) AND "High Int X en" is "0" OR (DATAY > "High Threshold" x 16) AND "High Int Y en" is "0" OR (DATAZ > "High Threshold" x 16) AND "High Int Z en" is "0" Note: Threshold interrupt enable bits ("High INT [XYZ] en") are active low and "1" (disabled) by default. High threshold a a measurements INT3 pin (non-latched) INT3 pin (latched) Read interrupt status register (0x4A) Figure 17: High-threshold interrupt function BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 61 4.9.6 Overflow When a measurement axis had an overflow, the corresponding data register is saturated to the most negative value. For X and Y axis, the data register is set to the value -4096. For the Z axis, the data register is set to the value -16384. The "Overflow" flag (register 0x4A bit6) indicates that the measured magnetic field raw data of one or more axes exceeded maximum range of the device. The overflow condition can be flagged on the INT3 pin by setting the bit "overflow int enable" (register 0x4D bit6, active high, default value "0"). The channel on which overflow occurred can by determined by assessing the DATAX/Y/Z registers. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 62 5. FIFO Operation 5.1 FIFO Operating Modes The IC of the accelerometer part of BMC150 features an integrated FIFO memory capable of storing up to 32 frames. Conceptually each frame consists of three 16-bit words corresponding to the x, y and z- axis, which are sampled at the same point in time. At the core of the FIFO is a buffer memory, which can be configured to operate in the following modes: FIFO Mode: In FIFO mode the acceleration data of the selected axes are stored in the buffer memory. If enabled, a watermark interrupt is triggered when the buffer has filled up to a configurable level. The buffer will be continuously filled until the fill level reaches 32 frames. When it is full the data collection is stopped, and all additional samples are ignored. Once the buffer is full, a FIFO-full interrupt is generated if it has been enabled. STREAM Mode: In STREAM mode the acceleration data of the selected axes are stored in the buffer until it is full. The buffer has a depth of 31 frames. When the buffer is full the data collection continues and oldest entry is discarded. If enabled, a watermark interrupt is triggered when the buffer is filled to a configurable level. Once the buffer is full, a FIFO-full interrupt is generated if it has been enabled. BYPASS Mode: In bypass mode, only the current sensor data can be read out from the FIFO address. Essentially, the FIFO behaves like the STREAM mode with a depth of 1. Compared to reading the data from the normal data registers, the advantage to the user is that the packages X, Y, Z are from the same timestamp, while the data registers are updated sequentially and hence mixing of data from different axes can occur. The primary FIFO operating mode is selected with register (0x3E) fifo_mode according to `00b' for BYPASS mode, `01b' for FIFO mode, and `10b' for STREAM mode. Writing to register (0x3E) clears the buffer content and resets the FIFO-full and watermark interrupts. When reading register (0x3E) fifo_mode always contains the current operating mode. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 63 5.2 FIFO Data Readout The FIFO stores the data that are also available at the acceleration read-out registers (0x02) to (0x07). Thus, all configuration settings apply to the FIFO data as well as the acceleration data readout registers. The FIFO read out is possible through register (0x3F). The readout can be performed using burst mode since the read address counter is no longer incremented, when it has reached address (0x3F). This implies that the trapping also occurs when the burst read access starts below address (0x3F). A single burst can read out one or more frames at a time. Register (0x3E) fifo_data_select controls the acceleration data of which axes are stored in the FIFO. Possible settings for register (0x3E) fifo_data_select are `00b' for x, y- and z-axis, `01b' for x-axis only, `10b' for y-axis, `11b' for z-axis only. The depth of the FIFO is independent of whether all or a single axis have been selected. Writing to register (0x3E) clears the buffer content and resets the FIFO-full and watermark interrupts. If all axes are enabled, the format of the data read-out from register (0x3F) is as follows: ... X LSB X MSB Y LSB Y MSB Z LSB Z MSB ... Frame 1 If only one axis is enabled, the format of the data read-out from register (0x3F) is as follows (example shown: y-axis only, other axes are equivalent). Y LSB Y MSB Frame 1 Y LSB Y MSB ... Frame 2 If a frame is not completely read due to an incomplete read operation, the remaining part of the frame is discarded. In this case the FIFO aligns to the next frame during the next read operation. In order for the discarding mechanism to operate correctly, there must be a delay of at least 1.5 us between the last data bit of the partially read frame and the first address bit of the next FIFO read access. Otherwise frames must not be read out partially. If the FIFO is read beyond the FIFO fill level zeroes (0) will be read. If the FIFO is read beyond the FIFO fill level the read or burst read access time must not exceed the sampling time tSAMPLE. Otherwise frames may be lost. 5.3 FIFO Frame Counter and Overrun Flag Register (0x0E) fifo_frame_counter reflects the current fill level of the buffer. If additional frames are written to the buffer although the FIFO is full, the (0x0E) fifo_overrun bit is set to `1'. The FIFO buffer is cleared, the FIFO fill level indicated in register (0x0E) fifo_frame_counter and the (0x0E) fifo_overrun bit are both set to `0' each time one a write access to one of the FIFO configuration registers (0x3E) or (0x30) occurs. The (0x0E) fifo_overrun bit is not reset when the FIFO fill level (0x0E) fifo_frame_counter has decremented to `0' due to reading from register (0x3F). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 64 5.4 FIFO Interrupts The FIFO controller can generate two different interrupt events, a FIFO-full and a watermark event. The FIFO-full and watermark interrupts are functional in all FIFO operating modes. The watermark interrupt is asserted when the fill level in the buffer has reached the frame count defined by register (0x30) fifo_water_mark_trigger_retain. In order to enable (disable) the watermark interrupt, the (0x17) int_fwm_en bit must be set to `1' (`0'). To map the watermark interrupt signal to INT1 pin (INT2 pin), (0x1A) int1_fwm ((0x1A) int2_fwm) bit must be set to `1'. The status of the watermark interrupt may be read back through the (0x0A) fifo_wm_int bit. Writing to register (0x30) fifo_water_mark_trigger_retain clears the FIFO buffer. The FIFO-full interrupt is triggered when the buffer has been completely filled. In FIFO mode this occurs 32, in STREAM mode 31 samples, and in BYPASS mode 1 sample after the buffer has been cleared. In order to enable the FIFO-full interrupt, bit (0x17) int_ffull_en as well as one or both of bits (0x1A) int1_fful or (0x1A) int2_fful must also be set to `1'. The status of the FIFOfull interrupt may be read back through bit (0x0A) fifo_full_int. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 65 6. Accelerometer register description 6.1 General remarks The entire communication with the device is performed by reading from and writing to registers. Registers have a width of 8 bits; they are mapped to a common space of 64 addresses from (0x00) up to (0x3F). Within the used range there are several registers which are either completely or partially marked as `reserved'. Any reserved bit is ignored when it is written and no specific value is guaranteed when read. It is recommended not to use registers at all which are completely marked as `reserved'. Furthermore it is recommended to mask out (logical and with zero) reserved bits of registers which are partially marked as reserved. Registers with addresses from (0x00) up to (0x0E) are read-only. Any attempt to write to these registers is ignored. There are bits within some registers that trigger internal sequences. These bits are configured for write-only access, e. g. (0x21) reset_int or the entire (0x14) softreset register, and read as value 0. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 66 6.2 Register map Register Address 0x3F 0x3E 0x3D 0x3C 0x3B 0x3A 0x39 0x38 0x37 0x36 0x35 0x34 0x33 0x32 0x31 0x30 0x2F 0x2E 0x2D 0x2C 0x2B 0x2A 0x29 0x28 0x27 0x26 0x25 0x24 0x23 0x22 0x21 0x20 0x1F 0x1E 0x1D 0x1C 0x1B 0x1A 0x19 0x18 0x17 0x16 0x15 0x14 0x13 0x12 0x11 0x10 0x0F 0x0E 0x0D 0x0C 0x0B 0x0A 0x09 0x08 0x07 0x06 0x05 0x04 0x03 0x02 0x01 0x00 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 Access Default fifo_data_output_register<7:0> fifo_mode<1:0> fifo_data_select<1:0> GP1<7:0> GP0<7:0> offset_z<7:0> offset_y<7:0> offset_x<7:0> offset_target_y<1:0> cal_rdy offset_target_z<1:0> cal_trigger<1:0> offset_reset nvm_remain<3:0> offset_target_x<1:0> hp_z_en hp_y_en i2c_wdt_en nvm_rdy self_test_sign nvm_load self_test_amp cut_off hp_x_en i2c_wdt_sel spi3 nvm_prog_trig nvm_prog_mode self_test_axis<1:0> fifo_water_mark_level_trigger_retain<5:0> flat_hold_time<1:0> flat_hy<2:0> flat_theta<5:0> orient_theta<5:0> orient_blocking<1:0> tap_th<4:0> orient_ud_en orient_hyst<2:0> tap_samp<1:0> tap_quiet tap_shock orient_mode<1:0> tap_dur<2:0> slo_no_mot_th<7:0> slope_th<7:0> slo_no_mot_dur<5:0> slope_dur<1:0> high_th<7:0> high_dur<7:0> high_hy<1:0> low_mode low_hy<1:0> low_th<7:0> low_dur<7:0> reset_int int2_od int2_lvl latch_int<3:0> int1_od int1_lvl int_src_data int_src_tap int_src_slo_no_mot int_src_slope int_src_high int_src_low int2_slope int1_ffull int1_slope slo_no_mot_en_z high_en_z slope_en_z int2_high int1_fwm int1_high slo_no_mot_en_y high_en_y slope_en_y int2_low int1_data int1_low slo_no_mot_en_x high_en_x slope_en_x int2_flat int2_data int1_flat int2_orient int2_fwm int1_orient int2_s_tap int2_ffull int1_s_tap int2_d_tap int2_slo_no_mot int1_d_tap flat_en int_fwm_en orient_en int_ffull_en s_tap_en data_en d_tap_en int1_slo_no_mot slo_no_mot_sel low_en shadow_dis lowpower_mode lowpower_en sleeptimer_mode deep_suspend softreset data_high_bw suspend sleep_dur<3:0> bw<4:0> range<3:0> fifo_overrun flat tap_sign data_int flat_int fifo_frame_counter<6:0> tap_first_z fifo_wm_int orient_int orient<2:0> tap_first_y fifo_full_int s_tap_int tap_first_x high_sign slope_sign d_tap_int slo_no_mot_int temp<7:0> acc_z_msb<11:4> acc_z_lsb<3:0> high_first_z slope_first_z high_first_y slope_first_y high_first_x slope_first_x slope_int high_int low_int new_data_z acc_y_msb<11:4> acc_y_lsb<3:0> new_data_y acc_x_msb<11:4> acc_x_lsb<3:0> new_data_x chip_id<7:0> ro w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r w/r wo w/r w/r w/r w/r w/r ro w/r ro ro ro ro ro ro ro ro ro ro ro ro ro 0x00 0x00 0xFF 0x00 0x00 0x00 0x00 0x00 0x00 0x10 0x00 0x00 0xF0 0x00 0xFF 0x00 0x11 0x08 0x48 0x18 0x0A 0x04 0x14 0x14 0x00 0xC0 0x0F 0x81 0x30 0x09 0x00 0x05 0xFF 0x00 0xFF 0xFF 0x00 0x00 0x00 0x00 0x00 0x00 0xFF 0x00 0x00 0x00 0x00 0x0F 0x03 0x00 0xFF 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 -0xFA common w/r registers: Application specific settings which are not equal to the default settings, must be re-set to its designated values after POR, soft-reset and wake up from deep suspend. user w/r registers: Initial default content = 0x00. Freely programmable by the user. Remains unchanged after POR, soft-reset and wake up from deep suspend. Figure 18: Register map BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 67 6.3 Chip ID Register 0x00 (BGW_CHIPID) The register contains the chip identification code. Name Bit Read/Write Reset Value Content 0x00 7 R n/a Bit Read/Write Reset Value Content 3 R n/a chip_id<7:0>: 6 R n/a BGW_CHIPID 5 R n/a 4 R n/a chip_id<7:4> 2 R n/a 1 R n/a 0 R n/a chip_id<3:0> Fixed value b'1111'1010 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 68 6.4 Acceleration data Register 0x02 (ACCD_X_LSB) The register contains the least-significant bits of the X-channel acceleration readout value. When reading out X-channel acceleration values, data consistency is guaranteed if the ACCD_X_LSB is read out before the ACCD_X_MSB and shadow_dis='0'. In this case, after the ACCD_X_LSB has been read, the value in the ACCD_X_MSB register is locked until the ACCD_X_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_X_LSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x02 7 R n/a Bit Read/Write Reset Value Content 3 R n/a 2 R n/a 1 R n/a 0 R n/a undefined undefined `0' new_data_x acc_x_lsb<3:0>: undefined: New_data_x: ACCD_X_LSB 5 R n/a 6 R n/a 4 R n/a acc_x_lsb<3:0> Least significant 4 bits of acceleration read-back value; (two's-complement format) random data; to be ignored. `0': acceleration value has not been updated since it has been read out last `1': acceleration value has been updated since it has been read out last Register 0x03 (ACCD_X_MSB) The register contains the most-significant bits of the X-channel acceleration readout value. When reading out X-channel acceleration values, data consistency is guaranteed if the ACCD_X_LSB is read out before the ACCD_X_MSB and shadow_dis='0'. In this case, after the ACCD_X_LSB has been read, the value in the ACCD_X_MSB register is locked until the ACCD_X_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_X_MSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x03 7 R n/a BST-BMC150-DS000-04 | Revision 1.0 | July 2014 6 R n/a ACCD_X_MSB 5 R n/a 4 R n/a acc_x_msb<11:8> Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Bit Read/Write Reset Value Content 3 R n/a 2 R n/a Page 69 1 R n/a 0 R n/a acc_x_msb<7:4> acc_x_msb<11:4>: Most significant 8 bits of acceleration readback value (two's-complement format) Register 0x04 (ACCD_Y_LSB) The register contains the least-significant bits of the Y-channel acceleration readout value. When reading out Y-channel acceleration values, data consistency is guaranteed if the ACCD_Y_LSB is read out before the ACCD_Y_MSB and shadow_dis='0'. In this case, after the ACCD_Y_LSB has been read, the value in the ACCD_Y_MSB register is locked until the ACCD_Y_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_Y_LSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x04 7 R n/a Bit Read/Write Reset Value Content 3 R n/a 2 R n/a 1 R n/a 0 R n/a undefined undefined `0' new_data_y acc_y_lsb<3:0>: undefined: new_data_y: ACCD_Y_LSB 5 R n/a 6 R n/a 4 R n/a acc_y_lsb<3:0> Least significant 4 bits of acceleration readback value; (two's-complement format) random data; to be ignored `0': acceleration value has not been updated since it has been read out last `1': acceleration value has been updated since it has been read out last BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 70 Register 0x05 (ACCD_Y_MSB) The register contains the most-significant bits of the Y-channel acceleration readout value. When reading out Y-channel acceleration values, data consistency is guaranteed if the ACCD_Y_LSB is read out before the ACCD_Y_MSB and shadow_dis='0'. In this case, after the ACCD_Y_LSB has been read, the value in the ACCD_Y_MSB register is locked until the ACCD_Y_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_Y_MSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x05 7 R n/a Bit Read/Write Reset Value Content 3 R n/a ACCD_Y_MSB 5 R n/a 6 R n/a 4 R n/a acc_y_msb<11:8> 2 R n/a 1 R n/a 0 R n/a acc_y_msb<7:4> acc_y_msb<11:4>: Most significant 8 bits of acceleration readback value (two's-complement format) Register 0x06 (ACCD_Z_LSB) The register contains the least-significant bits of the Z-channel acceleration readout value. When reading out Z-channel acceleration values, data consistency is guaranteed if the ACCD_Z_LSB is read out before the ACCD_Z_MSB and shadow_dis='0'. In this case, after the ACCD_Z_LSB has been read, the value in the ACCD_Z_MSB register is locked until the ACCD_Z_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_Z_LSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x06 7 R n/a ACCD_Z_LSB 5 R n/a Bit Read/Write Reset Value Content 3 R n/a 2 R n/a 1 R n/a 0 R n/a undefined undefined `0' new_data_z 6 R n/a 4 R n/a acc_z_lsb<3:0> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 71 Acc_z_lsb<3:0>: Least significant 4 bits of acceleration readback value; (two's-complement format) undefined: random data; to be ignored new_data_z: `0': acceleration value has not been updated since it has been read out last `1': acceleration value has been updated since it has been read out last Register 0x07 (ACCD_Z_MSB) The register contains the most-significant bits of the Z-channel acceleration readout value. When reading out Z-channel acceleration values, data consistency is guaranteed if the ACCD_Z_LSB is read out before the ACCD_Z_MSB and shadow_dis='0'. In this case, after the ACCD_Z_LSB has been read, the value in the ACCD_Z_MSB register is locked until the ACCD_Z_MSB has been read. This condition is inherently fulfilled if a burst-mode read access is performed. Acceleration data may be read from register ACCD_Z_MSB at any time except during power-up and in DEEP_SUSPEND mode. Name Bit Read/Write Reset Value Content 0x07 7 R n/a Bit Read/Write Reset Value Content 3 R n/a 6 R n/a ACCD_Z_MSB 5 R n/a 4 R n/a acc_z_msb<11:8> 2 R n/a 1 R n/a 0 R n/a acc_z_msb<7:4> acc_z_msb<11:4>: Most significant 8 bits of acceleration readback value (two's-complement format) BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 72 6.5 Temperature data Register 0x08 (ACCD_TEMP) The register contains the current chip temperature represented in two's complement format. A readout value of temp<7:0>=0x00 corresponds to a temperature of 24C. Name Bit Read/Write Reset Value Content 0x08 7 R n/a Bit Read/Write Reset Value Content 3 R n/a temp<7:0>: 6 R n/a ACCD_TEMP 5 R n/a 4 R n/a temp<7:4> 2 R n/a 1 R n/a 0 R n/a temp<3:0> Temperature value (two s-complement format) BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 73 6.6 Status registers Register 0x09 (INT_STATUS_0) The register contains interrupt status flags. Each flag is associated with a specific interrupt function. It is set when the associated interrupt triggers. The setting of latch_int<3:0> controls if the interrupt signal and hence the respective interrupt flag will be permanently latched, temporarily latched or not latched. The interrupt function associated with a specific status flag must be enabled. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 6 R n/a INT_STATUS_0 5 R n/a 4 R n/a flat_int orient_int s_tap_int d_tap_int 3 R n/a 2 R n/a 1 R n/a 0 R n/a slo_no_mot_int slope_int high_int low_int flat_int: orient_int : s_tap_int: d_tap_int slo_not_mot_int: slope_int: high_int: low_int: 0x09 7 R n/a flat interrupt status: `0'inactive, `1' active orientation interrupt status : `0'inactive, `1' active single tap interrupt status: `0'inactive, `1' active double tap interrupt status: `0'inactive, `1' active slow/no-motion interrupt status: `0'inactive, `1' active slope interrupt status: `0'inactive, `1' active high-g interrupt status: `0'inactive, `1' active low-g interrupt status: `0'inactive, `1' active Register 0x0A (INT_STATUS_1) The register contains interrupt status flags. Each flag is associated with a specific interrupt function. It is set when the associated interrupt engine triggers. The setting of latch_int<3:0> controls if the interrupt signal and hence the respective interrupt flag will be permanently latched, temporarily latched or not latched. The interrupt function associated with a specific status flag must be enabled. Name Bit Read/Write Reset Value Content 0x0A 7 R n/a 6 R n/a INT_STATUS_1 5 R n/a 4 R n/a data_int fifo_wm_int fifo_full_int reserved BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Bit Read/Write Reset Value Content data_int: fifo_wm_int: fifo_full_int: reserved: 3 R n/a 2 R n/a Page 74 1 R n/a 0 R n/a reserved data ready interrupt status: `0'inactive, `1' active FIFO watermark interrupt status: `0'inactive, `1' active FIFO full interrupt status: `0'inactive, `1' active reserved, write to `0' Register 0x0B (INT_STATUS_2) The register contains interrupt status flags. Each flag is associated with a specific interrupt engine. It is set when the associated interrupt engine triggers. The setting of latch_int<3:0> controls if the interrupt signal and hence the respective interrupt flag will be permanently latched, temporarily latched or not latched. The interrupt function associated with a specific status flag must be enabled. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content tap_sign: tap_first_z: tap_first_y: tap_first_x: slope_sign: slope_first_z: slope_first_y: slope_first_x: 0x0B 7 R n/a 6 R n/a INT_STATUS_2 5 R n/a 4 R n/a tap_sign tap_first_z tap_first_y tap_first_x 3 R n/a 2 R n/a 1 R n/a 0 R n/a slope_sign slope_first_z slope_first_y slope_first_x sign of single/double tap triggering signal was `0'positive, or `1' negative single/double tap interrupt: `1' triggered by, or `0'not triggered by z-axis single/double tap interrupt: `1' triggered by, or `0'not triggered by y-axis single/double tap interrupt: `1' triggered by, or `0'not triggered by x-axis slope sign of slope tap triggering signal was `0'positive, or `1' negative slope interrupt: `1' triggered by, or `0'not triggered by z-axis slope interrupt: `1' triggered by, or `0'not triggered by y-axis slope interrupt: `1' triggered by, or `0'not triggered by x-axis Register 0x0C (INT_STATUS_3) The register contains interrupt status flags. Each flag is associated with a specific interrupt engine. It is set when the associated interrupt engine triggers. With the exception of orient<3:0> the setting of latch_int<3:0> controls if the interrupt signal and hence the respective interrupt BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 75 flag will be permanently latched, temporarily latched or not latched. The interrupt function associated with a specific status flag must be enabled. Name Bit Read/Write Reset Value Content 0x0C 7 R n/a Bit Read/Write Reset Value Content 3 R n/a 2 R n/a 1 R n/a 0 R n/a high_sign high_first_z high_first_y high_first_x flat: orient<2>: Orient<1:0>: High_sign: high_first_z: high_first_y: high_first_x: 6 R n/a flat INT_STATUS_3 5 R n/a 4 R n/a orient<2:0> device is in `1' flat, or `0' non flat position; only valid if (0x16) flat_en = `1' Orientation value of z-axis: 0 upward looking, or 1 downward looking. The flag always reflect the current orientation status, independent of the setting of latch_int<3:0>. The flag is not updated as long as an orientation blocking condition is active. orientation value of x-y-plane: `00'portrait upright; `01'portrait upside down; `10'landscape left; `11'landscape right; The flags always reflect the current orientation status, independent of the setting of latch_int<3:0>. The flag is not updated as long as an orientation blocking condition is active. sign of acceleration signal that triggered high-g interrupt was `0'positive, `1' negative high-g interrupt: `1' triggered by, or `0'not triggered by z-axis high-g interrupt: `1' triggered by, or `0'not triggered by y-axis high-g interrupt: `1' triggered by, or `0'not triggered by x-axis Register 0x0E (FIFO_STATUS) The register contains FIFO status flags. Name Bit Read/Write Reset Value Content 0x0E 7 R n/a fifo_overrun BST-BMC150-DS000-04 | Revision 1.0 | July 2014 6 R n/a FIFO_STATUS 5 R n/a 4 R n/a fifo_frame_counter<6:4> Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Bit Read/Write Reset Value Content 3 R n/a 2 R n/a Page 76 1 R n/a 0 R n/a fifo_frame_counter<3:0> fifo_overrun: FIFO overrun condition has `1' occurred, or `0'not occurred; flag can be cleared by writing to the FIFO configuration register FIFO_CONFIG_1 only fifo_frame_counter<6:4>: Current fill level of FIFO buffer. An empty FIFO corresponds to 0x00. The frame counter can be cleared by reading out all frames from the FIFO buffer or writing to the FIFO configuration register FIFO_CONFIG_1. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 77 6.7 g-range selection Register 0x0F (PMU_RANGE) The register allows the selection of the accelerometer g-range. Name Bit Read/Write Reset Value Content 0x0F 7 R/W 0 6 R/W 0 PMU_RANGE 5 R/W 0 4 R/W 0 reserved 0 Bit Read/Write Reset Value Content range<3:0>: reserved: 3 R/W 0 2 R/W 0 1 R/W 1 0 R/W 1 range<3:0> Selection of accelerometer g-range: 0011b 2g range; 0101b 4g range; 1000b 8g range; 1100b 16g range; all other settings reserved (do not use) write `0' BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 78 6.8 Bandwidths Register 0x10 (PMU_BW) The register allows the selection of the acceleration data filter bandwidth. Name Bit Read/Write Reset Value Content 0x10 7 R/W 0 PMU_BW 5 R/W 0 6 R/W 0 reserved 4 R/W 0 bw<4> 0 Bit Read/Write Reset Value Content bw<4:0>: reserved: 3 R/W 1 2 R/W 1 1 R/W 1 0 R/W 1 bw<3:0> Selection of data filter bandwidth: 00xxxb 7.81 Hz, 01000b 7.81 Hz, 01001b 15.63 Hz, 01010b 31.25 Hz, 01011b 62.5 Hz, 01100b 125 Hz, 01101b 250 Hz, 01110b 500 Hz, 01111b 1000 Hz, 1xxxxb 1000 Hz write `0' BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 79 6.9 Power modes Register 0x11 (PMU_LPW) Selection of the main power modes and the low power sleep period. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x11 7 R/W 0 6 R/W 0 PMU_LPW 5 R/W 0 4 R/W 0 suspend lowpower_en deep_suspend sleep_dur<3> 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 sleep_dur<2:0> reserved suspend, low_power_en, deep_suspend: Main power mode configuration setting {suspend; lowpower_en; deep_suspend}: {0; 0; 0} NORMAL mode; {0; 0; 1} DEEP_SUSPEND mode; {0; 1; 0} LOW_POWER mode; {1; 0; 0} SUSPEND mode; {all other} illegal Please note that only certain power mode transitions are permitted. Sleep_dur<3:0>: Configures the sleep phase duration in LOW_POWER mode: 0000b to 0101b 0.5 ms, 0110b 1 ms, 0111b 2 ms, 1000b 4 ms, 1001b 6 ms, 1010b 10 ms, 1011b 25 ms, 1100b 50 ms, 1101b 100 ms, 1110b 500 ms, 1111b 1s Register 0x12 (PMU_LOW_POWER) Configuration settings for low power mode. Name Bit Read/Write Reset Value Content 0x12 7 R/W 0 reserved BST-BMC150-DS000-04 | Revision 1.0 | July 2014 6 R/W 0 PMU_LOW_POWER 5 R/W 0 4 R/W 0 lowpower_mode sleeptimer_mode reserved Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 Page 80 1 R/W 0 0 R/W 0 reserved lowpower_mode: select `0' LPM1, or `1 LPM2 configuration for SUSPEND and LOW_POWER mode. In the LPM1 configuration the power consumption in LOW_POWER mode and SUSPEND mode is significantly reduced when compared to LPM2 configuration, but the FIFO is not accessible and writing to registers must be slowed down. In the LPM2 configuration the power consumption in LOW_POWER mode is reduced compared to NORMAL mode, but the FIFO is fully accessible and registers can be written to at full speed. Sleeptimer_mode: when in LOW_POWER mode `0' use event-driven time-base mode (compatible with BMA250), or `1 use equidistant sampling time-base mode. Equidistant sampling of data into the FIFO is maintained in equidistant time-base mode only. Reserved: write `0' BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 81 6.10 Special control settings Register 0x13 (ACCD_HBW) Acceleration data acquisition and data output format. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content data_high_bw: Shadow_dis: Reserved: 0x13 7 R/W 0 data_high_bw 6 R/W 0 (1 in 8-bit mode) shadow_dis 3 R/W 0 2 R/W 0 ACCD_HBW 5 R/W 0 4 R/W 0 reserved 1 R/W 0 0 R/W 0 reserved select whether `1 unfiltered, or `0' filtered data may be read from the acceleration data registers. `1 disable, or `0' the shadowing mechanism for the acceleration data output registers. When shadowing is enabled, the content of the acceleration data component in the MSB register is locked, when the component in the LSB is read, thereby ensuring the integrity of the acceleration data during read-out. The lock is removed when the MSB is read. write `1' Register 0x14 (BGW_SOFTRESET) Controls user triggered reset of the sensor. Name Bit Read/Write Reset Value Content 0x14 7 W 0 Bit Read/Write Reset Value Content 3 W 0 softreset: 6 W 0 BGW_SOFTRESET 5 W 0 4 W 0 softreset 2 W 0 1 W 0 0 W 0 softreset 0xB6 triggers a reset. Other values are ignored. Following a delay, all user configuration settings are overwritten with their default state or the setting stored in the NVM, wherever applicable. This register is functional in all BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 82 operation modes. Please note that all application specific settings which are not equal to the default settings (refer to chapter 6.2), must be reconfigured to their designated values. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 83 6.11 Interrupt settings Register 0x16 (INT_EN_0) Controls which interrupt engines in group 0 are enabled. Name Bit Read/Write Reset Value Content 0x16 7 R/W 0 6 R/W 0 INT_EN_0 5 R/W 0 4 R/W 0 flat_en orient_en s_tap_en d_tap_en Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 reserved slope_en_z slope_en_y slope_en_x flat_en: orient_en: s_tap_en: d_tap_en reserved: slope_en_z: slope_en_y: slope_en_x: flat interrupt: `0'disabled, or `1' enabled orientation interrupt: `0'disabled, or `1' enabled single tap interrupt: `0'disabled, or `1' enabled double tap interrupt: `0'disabled, or `1' enabled write `0' slope interrupt, z-axis component: `0'disabled, or `1' enabled slope interrupt, y-axis component: `0'disabled, or `1' enabled slope interrupt, x-axis component: `0'disabled, or `1' enabled Register 0x17 (INT_EN_1) Controls which interrupt engines in group 1 are enabled. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content reserved: 0x17 7 R/W 0 6 R/W 0 INT_EN_1 5 R/W 0 4 R/W 0 reserved int_fwm_en int_ffull_en data_en 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 low_en high_en_z high_en_y high_en_x write `0' BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 int_fwm_en: int_ffull_en: data_en low_en: high_en_z: high_en_y: high_en_x: Page 84 FIFO watermark interrupt: `0'disabled, or `1' enabled FIFO full interrupt: `0'disabled, or `1' enabled data ready interrupt: `0'disabled, or `1' enabled low-g interrupt: `0'disabled, or `1' enabled high-g interrupt, z-axis component: `0'disabled, or `1' enabled high-g interrupt, y-axis component: `0'disabled, or `1' enabled high-g interrupt, x-axis component: `0'disabled, or `1' enabled Register 0x18 (INT_EN_2) Controls which interrupt engines in group 2 are enabled. Name Bit Read/Write Reset Value Content 0x18 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 slo_no_mot_sel INT_EN_2 5 R/W 0 4 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 slo_no_mot_en_z slo_no_mot_en_y slo_no_mot_en_x 6 R/W 0 reserved reserved: write `0' slo_no_mot_sel: select `0'slow-motion, `1' no-motion interrupt function slo_no_mot_en_z: slow/n-motion interrupt, z-axis component: `0'disabled, or `1' enabled slo_no_mot_en_y: slow/n-motion interrupt, y-axis component: `0'disabled, or `1' enabled slo_no_mot_en_x: slow/n-motion interrupt, x-axis component: `0'disabled, or `1' enabled Register 0x19 (INT_MAP_0) Controls which interrupt signals are mapped to the INT1 pin. Name Bit Read/Write Reset Value Content 0x19 7 R/W 0 6 R/W 0 INT_MAP_0 5 R/W 0 4 R/W 0 int1_flat int1_orient int1_s_tap int1_d_tap BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Bit Read/Write Reset Value Content Page 85 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 int1_slo_no_mot int1_slope int1_high int1_low int1_flat: int1_orient: int1_s_tap: int1_d_tap: int1_slo_no_mot: int1_slope: int1_high: int1_low: map flat interrupt to INT1 pin: `0'disabled, or `1' enabled map orientation interrupt to INT1 pin: `0'disabled, or `1' enabled map single tap interrupt to INT1 pin: `0'disabled, or `1' enabled map double tap interrupt to INT1 pin: `0'disabled, or `1' enabled map slow/no-motion interrupt to INT1 pin: `0'disabled, or `1' enabled map slope interrupt to INT1 pin: `0'disabled, or `1' enabled map high-g to INT1 pin: `0'disabled, or `1' enabled map low-g to INT1 pin: `0'disabled, or `1' enabled Register 0x1A (INT_MAP_1) Controls which interrupt signals are mapped to the INT1 and INT2 pins. Name Bit Read/Write Reset Value Content 0x1A 7 R/W 0 6 R/W 0 INT_MAP_1 5 R/W 0 4 R/W 0 int2_data int2_fwm int2_ffull reserved Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 reserved int1_ffull int1_fwm int1_data int2_data: int2_fwm: int2_ffull: reserved: int1_ffull: int1_fwm: int1_data: map data ready interrupt to INT2 pin: `0'disabled, or `1' enabled map FIFO watermark interrupt to INT2 pin: `0'disabled, or `1' enabled map FIFO full interrupt to INT2 pin: `0'disabled, or `1' enabled write `0' map FIFO full interrupt to INT1 pin: `0'disabled, or `1' enabled map FIFO watermark interrupt to INT1 pin: `0'disabled, or `1' enabled map data ready interrupt to INT1 pin: `0'disabled, or `1' enabled BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 86 Register 0x1B (INT_MAP_2) Controls which interrupt signals are mapped to the INT2 pin. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 6 R/W 0 INT_MAP_2 5 R/W 0 4 R/W 0 int2_flat int2_orient int2_s_tap int2_d_tap 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 int2_slo_no_mot int2_slope int2_high int2_low int2_flat: int2_orient: int2_s_tap: int2_d_tap: int2_slo_no_mot: int2_slope: int2_high: int2_low: 0x1B 7 R/W 0 map flat interrupt to INT2 pin: `0'disabled, or `1' enabled map orientation interrupt to INT2 pin: `0'disabled, or `1' enabled map single tap interrupt to INT2 pin: `0'disabled, or `1' enabled map double tap interrupt to INT2 pin: `0'disabled, or `1' enabled map slow/no-motion interrupt to INT2 pin: `0'disabled, or `1' enabled map slope interrupt to INT2 pin: `0'disabled, or `1' enabled map high-g to INT2 pin: `0'disabled, or `1' enabled map low-g to INT2 pin: `0'disabled, or `1' enabled Register 0x1E (INT_SRC) Contains the data source definition for interrupts with selectable data source. Name Bit Read/Write Reset Value Content 0x1E 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 int_src_slo_no_m ot reserved: int_src_data: int_src_tap: INT_SRC 5 R/W 0 4 R/W 0 int_src_data int_src_tap 2 R/W 0 1 R/W 0 0 R/W 0 int_src_slope int_src_high int_src_low 6 R/W 0 reserved write `0' select `0'filtered, or `1' unfiltered data for new data interrupt select `0'filtered, or `1' unfiltered data for single-/double tap interrupt BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 87 int_src_slo_no_mot: select `0'filtered, or `1' unfiltered data for slow/no-motion interrupt int_src_slope: select `0'filtered, or `1' unfiltered data for slope interrupt int_src_high: select `0'filtered, or `1' unfiltered data for high-g interrupt int_src_low: select `0'filtered, or `1' unfiltered data for low-g interrupt Register 0x20 (INT_OUT_CTRL) Contains the behavioural configuration (electrical 87ehavior) of the interrupt pins. Name Bit Read/Write Reset Value Content 0x20 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 1 1 R/W 0 0 R/W 1 int2_od int2_lvl int1_od int1_lvl reserved: int2_od: int2_lvl: int1_od: int1_lvl: INT_OUT_CTRL 5 R/W 0 6 R/W 0 4 R/W 0 reserved write `0' select `0'push-pull, or `1' open drain behavior for INT2 pin select `0'active low, or `1'active high level for INT2 pin select `0'push-pull, or `1' open drain behavior for INT1 pin select `0'active low, or `1'active high level for INT1 pin Register 0x21 (INT_RST_LATCH) Contains the interrupt reset bit and the interrupt mode selection. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x21 7 W 0 6 R/W 0 reset_int 3 R/W 0 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 INT_RST_LATCH 5 R/W 0 4 R/W 0 reserved 2 R/W 0 1 R/W 0 0 R/W 0 latch_int<3:0> Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 reset_int: reserved: latch_int<3:0>: Page 88 write `1' clear any latched interrupts, or `0' keep latched interrupts active write `0' 0000b non-latched, 0001b temporary, 250 ms, 0010b temporary, 500 ms, 0011b temporary, 1 s, 0100b temporary, 2 s, 0101b temporary, 4 s, 0110b temporary, 8 s, 0111b latched, 1000b non-latched, 1001b temporary, 250 s, 1010b temporary, 500 s, 1011b temporary, 1 ms, 1100b temporary, 12.5 ms, 1101b temporary, 25 ms, 1110b temporary, 50 ms, 1111b latched Register 0x22 (INT_0) Contains the delay time definition for the low-g interrupt. Name Bit Read/Write Reset Value Content 0x22 7 W 0 Bit Read/Write Reset Value Content 3 R/W 1 low_dur<7:0>: 6 R/W 0 INT_0 5 R/W 0 4 R/W 0 1 R/W 0 0 R/W 1 low_dur<7:4> 2 R/W 0 low_dur<3:0> low-g interrupt trigger delay according to [low_dur<7:0> + 1] * 2 ms in a range from 2 ms to 512 ms; the default corresponds to a delay of 20 ms. Register 0x23 (INT_1) Contains the threshold definition for the low-g interrupt. Name Bit Read/Write Reset Value Content 0x23 7 W 0 Bit Read/Write Reset Value Content 3 R/W 0 6 R/W 0 INT_1 5 R/W 1 4 R/W 1 1 R/W 0 0 R/W 0 low_th<7:4> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 2 R/W 0 low_th<3:0> Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 low_th<7:0>: Page 89 low-g interrupt trigger threshold according to low_th<7:0> * 7.81 mg in a range from 0 g to 1.992 g; the default value corresponds to an acceleration of 375 mg Register 0x24 (INT_2) Contains the low-g interrupt mode selection, the low-g interrupt hysteresis setting, and the highg interrupt hysteresis setting. Name Bit Read/Write Reset Value Content 0x24 7 R/W 1 Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 reserved low_mode high_hy<1:0>: low_mode: low_hy<1:0>: INT_2 5 R/W 0 6 R/W 0 high_hy<1:0> 4 R/W 0 reserved 1 R/W 0 0 R/W 1 low_hy<1:0> hysteresis of high-g interrupt according to high_hy<1:0> * 125 mg (2-g range), high_hy<1:0> * 250 mg (4-g range), high_hy<1:0> * 500 mg (8-g range), or high_hy<1:0> * 1000 mg (16-g range) select low-g interrupt `0' single-axis mode, or `1' axis-summing mode hysteresis of low-g interrupt according to low_hy<1:0> * 125 mg independent of the selected accelerometer g-range Register 0x25 (INT_3) Contains the delay time definition for the high-g interrupt. Name Bit Read/Write Reset Value Content 0x25 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 1 high_dur<7:0>: 6 R/W 0 INT_3 5 R/W 0 4 R/W 0 high_dur<7:4> 2 R/W 1 1 R/W 1 0 R/W 1 high_dur<3:0> high-g interrupt trigger delay according to [high_dur<7:0> + 1] * 2 ms in a range from 2 ms to 512 ms; the default corresponds to a delay of 32 ms. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 90 Register 0x26 (INT_4) Contains the threshold definition for the high-g interrupt. Name Bit Read/Write Reset Value Content 0x26 7 R/W 1 Bit Read/Write Reset Value Content 3 R/W 0 high_th<7:0>: 6 R/W 1 INT_4 5 R/W 0 4 R/W 0 1 R/W 0 0 R/W 0 high_th<7:4> 2 R/W 0 high_th<3:0> threshold of high-g interrupt according to high_th<7:0> * 7.81 mg (2-g range), high_th<7:0> * 15.63 mg (4-g range), high_th<7:0> * 31.25 mg (8-g range), or high_th<7:0> * 62.5 mg (16-g range) Register 0x27 (INT_5) Contains the definition of the number of samples to be evaluated for the slope interrupt (anymotion detection) and the slow/no-motion interrupt trigger delay. Name Bit Read/Write Reset Value Content 0x27 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 6 R/W 0 INT_5 5 R/W 0 4 R/W 0 slo_no_mot_dur<5:2> 2 R/W 0 slo_no_mot_dur<1:0> 1 R/W 0 0 R/W 0 slope_dur<1:0> slo_no_mot_dur<5:0>: Function depends on whether the slow-motion or no-motion interrupt function has been selected. If the slow-motion interrupt function has been enabled (slo_no_mot_sel = `0') then [slo_no_mot_dur<1:0>+1] consecutive slope data points must be above the slow/no-motion threshold (slo_no_mot_th) for the slow-/no-motion interrupt to trigger. If the no-motion interrupt function has been enabled (slo_no_mot_sel = `1') then slo_no_motion_dur<5:0> defines the time for which no slope data points must exceed the slow/no-motion threshold (slo_no_mot_th) for the slow/nomotion interrupt to trigger. The delay time in seconds may be calculated according with the following equation: BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 slope_dur<1:0>: Page 91 slo_no_mot_dur<5:4>='b00' [slo_no_mot_dur<3:0> + 1] slo_no_mot_dur<5:4>='b01' [slo_no_mot_dur<3:0> * 4 + 20] slo_no_mot_dur<5>='1' [slo_no_mot_dur<4:0> * 8 + 88] slope interrupt triggers if [slope_dur<1:0>+1] consecutive slope data points are above the slope interrupt threshold slope_th<7:0> Register 0x28 (INT_6) Contains the threshold definition for the any-motion interrupt. Name Bit Read/Write Reset Value Content 0x28 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 slope_th<7:0>: 6 R/W 0 INT_6 5 R/W 0 4 R/W 1 slope_th<7:4> 2 R/W 1 1 R/W 0 0 R/W 0 slope_th<3:0> Threshold of the any-motion interrupt. It is range-dependent and defined as a sample-to-sample difference according to slope_th<7:0> * 3.91 mg (2-g range) / slope_th<7:0> * 7.81 mg (4-g range) / slope_th<7:0> * 15.63 mg (8-g range) / slope_th<7:0> * 31.25 mg (16-g range) Register 0x29 (INT_7) Contains the threshold definition for the slow/no-motion interrupt. Name Bit Read/Write Reset Value Content 0x29 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 6 R/W 0 INT_7 5 R/W 0 4 R/W 1 slo_no_mot_th<7:4> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 2 R/W 1 1 R/W 0 0 R/W 0 slo_no_mot_th<3:0> Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 92 slo_no_mot_th<7:0>: Threshold of slow/no-motion interrupt. It is range-dependent and defined as a sample-to-sample difference according to slo_no_mot_th<7:0> * 3..91 mg (2-g range), slo_no_mot_th<7:0> * 7.81 mg (4-g range), slo_no_mot_th<7:0> * 15.63 mg (8-g range), slo_no_mot_th<7:0> * 31,25 mg (16-g range) Register 0x2A (INT_8) Contains the timing definitions for the single tap and double tap interrupts. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content tap_quiet: tap_shock: reserved: tap_dur<2:0>: 0x2A 7 R/W 0 6 R/W 0 INT_8 5 R/W 0 4 R/W 0 tap_quiet tap_shock reserved reserved 3 R/W 0 2 R/W 1 1 R/W 0 0 R/W 0 reserved tap_dur<2:0> selects a tap quiet duration of `0' 30 ms, `1' 20 ms selects a tap shock duration of `0' 50 ms, `1'75 ms write `0' selects the length of the time window for the second shock event for double tap detection according to 000b 50 ms, 001b 100 ms, 010b 150 ms, 011b 200 ms, 100b 250 ms, 101b 375 ms, 110b 500 ms, 111b 700 ms. Register 0x2B (INT_9) Contains the definition of the number of samples processed by the single / double-tap interrupt engine after wake-up in low-power mode. It also defines the threshold definition for the single and double tap interrupts. Name Bit Read/Write Reset Value Content 0x2B 7 R/W 0 Bit Read/Write Reset 3 R/W 1 6 R/W 0 tap_samp<1:0> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 2 R/W 0 INT_9 5 R/W 0 4 R/W 0 reserved tap_th<4> 1 R/W 1 0 R/W 0 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Value Content tap_samp<1:0>: reserved: tap_th<4:0>: Page 93 tap_th<3:0> selects the number of samples that are processed after wake-up in the lowpower mode according to 00b 2 samples, 01b 4 samples, 10b 8 samples, and 11b 16 samples write `0' threshold of the single/double-tap interrupt corresponding to an acceleration difference of tap_th<4:0> * 62.5mg (2g-range), tap_th<4:0> * 125mg (4grange), tap_th<4:0> * 250mg (8g-range), and tap_th<4:0> * 500mg (16grange). Register 0x2C (INT_A) Contains the definition of hysteresis, blocking, and mode for the orientation interrupt Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x2C 7 R/W 0 6 R/W 0 reserved 3 R/W 1 INT_A 5 R/W 0 4 R/W 1 orient_hyst<2:0> 2 R/W 0 orient_blocking<1:0> 1 R/W 0 0 R/W 0 orient_mode<1:0> reserved: write `0' orient_hyst<2:0>: sets the hysteresis of the orientation interrupt; 1 LSB corresponds to 62.5 mg irrespective of the selected g-range orient_blocking<1:0>: selects the blocking mode that is used for the generation of the orientation interrupt. The following blocking modes are available: 00b no blocking, 01b theta blocking or acceleration in any axis > 1.5g, 10b ,theta blocking or acceleration slope in any axis > 0.2 g or acceleration in any axis > 1.5g 11b theta blocking or acceleration slope in any axis > 0.4 g or acceleration in any axis > 1.5g and value of orient is not stable for at least 100ms orient_mode<1:0>: sets the thresholds for switching between the different orientations. The settings: 00b symmetrical, 01b high-asymmetrical, 10b lowasymmetrical, 11b symmetrical. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 94 Register 0x2D (INT_B) Contains the definition of the axis orientation, up/down masking, and the theta blocking angle for the orientation interrupt. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x2D 7 R/W n/a INT_B 5 R/W 0 6 R/W 1 reserved orient_ud_en 3 R/W 1 2 R/W 0 4 R/W 0 orient_theta<5:4> 1 R/W 0 0 R/W 0 orient_theta<3:0> orient_ud_en: change of up/down-bit 1 generates an orientation interrupt, 0 is ignored and will not generate an orientation interrupt orient_theta<5:0>: defines a blocking angle between 0 and 44.8 Register 0x2E (INT_C) Contains the definition of the flat threshold angle for the flat interrupt. Name Bit Read/Write Reset Value Content 0x2E 7 R/W n/a Bit Read/Write Reset Value Content 3 R/W 1 reserved: flat_theta<5:0>: 6 R/W n/a INT_C 5 R/W 0 reserved 4 R/W 0 flat_theta<5:4> 2 R/W 0 1 R/W 0 0 R/W 0 flat_theta<3:0> write `0' defines threshold for detection of flat position in range from 0 to 44.8. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 95 Register 0x2F (INT_D) Contains the definition of the flat interrupt hold time and flat interrupt hysteresis. Name Bit Read/Write Reset Value Content 0x2F 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 6 R/W 0 reserved reserved INT_D 5 R/W 0 4 R/W 1 flat_hold_time<1:0> 2 R/W 0 1 R/W 0 0 R/W 1 flat_hy<2:0> reserved: write `0' flat_hold_time<1:0>: delay time for which the flat value must remain stable for the flat interrupt to be generated: 00b 0 ms, 01b 512 ms, 10b 1024 ms, 11b 2048 ms flat_hy<2:0>: defines flat interrupt hysteresis; flat value must change by more than twice the value of flat interrupt hysteresis to detect a state change. For details see chapter 4.7.8. `000b' hysteresis of the flat detection disabled BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 96 6.12 Self-test Register 0x32 (PMU_SELF_TEST) Contains the settings for the sensor self-test configuration and trigger. Name Bit Read/Write Reset Value Content 0x32 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 reserved_0 self_test_sign reserved: reserved_0: self_test_amp; self_test_sign: self_test_axis: 6 R/W 0 PMU_SELF_TEST 5 R/W 0 reserved 4 R/W 0 self_test_amp 1 R/W 0 0 R/W 0 self_test-axis<1:0> write `0x0' write `0x0' select amplitude of the selftest deflection 1 high, default value is low (0) select sign of self-test excitation as 1 positive, or 0 negative select axis to be self-tested: 00b self-test disabled, 01b x-axis, 10b y-axis, or 11b z-axis; when a self-test is performed, only the acceleration data readout value of the selected axis is valid; after the self-test has been enabled a delay of a least 50 ms is necessary for the read-out value to settle BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 97 6.13 Non-volatile memory control (EEPROM) Register 0x33 (TRIM_NVM_CTRL) Contains the control settings for the few-time programmable non-volatile memory (NVM). Name Bit Read/Write Reset Value Content 0x33 7 R n/a Bit Read/Write Reset Value Content 3 R/W 0 2 R n/a 1 W 0 0 R/W 0 nvm_load nvm_rdy nvm_prog_trig nvm_prog_mode 6 R n/a TRIM_NVM_CTRL 5 R n/a 4 R n/a nvm_remain<3:0> nvm_remain<3:0>: number of remaining write cycles permitted for NVM; the number is decremented each time a write to the NVM is triggered nvm_load: 1 trigger, or `0' do not trigger an update of all configuration registers from NVM; the nvm_rdy flag must be `1' prior to triggering the update nvm_rdy: status of NVM controller: 0 NVM write / NVM update operation is in progress, 1 NVM is ready to accept a new write or update trigger nvm_prog_trig: `1' trigger, or `0' do not trigger an NVM write operation; the trigger is only accepted if the NVM was unlocked before and nvm_remain<3:0> is greater than `0'; flag nvm_rdy must be `1' prior to triggering the write cycle nvm_prog_mode: `1' unlock, or `0' lock NVM write operation BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 98 6.14 Interface configuration Register 0x34 (BGW_SPI3_WDT) Contains settings for the digital interfaces. Name Bit Read/Write Reset Value Content 0x34 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 reserved i2c_wdt_en i2c_wdt_sel spi3 reserved: i2c_wdt_en: i2c_wdt_sel: spi3: BGW_SPI3_WDT 5 R/W 0 6 R/W 0 4 R/W 0 Reserved write `0' if IC interface mode is selected then `1 enable, or `0' disables the watchdog at the SDI pin (= SDA for IC) select an IC watchdog timer period of `0' 1 ms, or `1' 50 ms select 0 4-wire SPI, or 1 3-wire SPI mode BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 99 6.15 Offset compensation Register 0x36 (OFC_CTRL) Contains control signals and configuration settings for the fast and the slow offset compensation. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x36 7 W 0 offset_reset OFC_CTRL 5 W 0 6 W 0 4 R 0 cal_trigger<1:0> cal_rdy 3 R/W 0 2 R/W 0 1 R/W 0 0 R/W 0 reserved hp_z_en hp_y_en hp_x_en offset_reset: 1 set all offset compensation registers (0x38 to 0x3A) to zero, or `0' keep their values offset_trigger<1:0>: trigger fast compensation for 01b x-axis, 10b y-axis, or 11b z-axis; 00b do not trigger offset compensation; offset compensation must not be triggered when cal_rdy is `0' cal_rdy: indicates the state of the fast compensation: 0 offset compensation is in progress, or 1 offset compensation is ready to be retriggered reserved: write `0' hp_z_en: `1 enable, or `0' disable slow offset compensation for the z-axis hp_y_en: `1 enable, or `0' disable slow offset compensation for the y-axis hp_x_en: `1 enable, or `0' disable slow offset compensation for the x-axis Register 0x37 (OFC_SETTING) Contains configuration settings for the fast and the slow offset compensation. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x37 7 R/W 0 reserved 3 R/W 0 offset_target_y<0 > BST-BMC150-DS000-04 | Revision 1.0 | July 2014 6 R/W 0 OFC_SETTING 5 R/W 0 offset_target_z<1:0> 2 R/W 0 1 R/W 0 offset_target_x<1:0> 4 R/W 0 offset_target_y<1> 0 R/W 0 cut_off Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 100 reserved: write `0' offset_target_z<1:0>: offset compensation target value for z-axis is 00b 0 g, 01b +1 g, 10b -1 g, or 11b 0 g offset_target_y<1:0>: offset compensation target value for y-axis is 00b 0 g, 01b +1 g, 10b -1 g, or 11b 0 g offset_target_x<1:0>: offset compensation target value for x-axis is 00b 0 g, 01b +1 g, 10b -1 g, or 11b 0 g cut_off: (0x37) cut_off high-pass filter bandwidth Example bw = 500 Hz 0b 1b *bw: please insert selected decimal data bandwidth value [Hz] from table 8 Register 0x38 (OFC_OFFSET_X) Contains the offset compensation value for x-axis acceleration readout data. Name Bit Read/Write Reset Value Content 0x38 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 offset_x<7:0>: 6 R/W 0 OFC_OFFSET_X 5 R/W 0 4 R/W 0 offset_x<7:4> 2 R/W 0 1 R/W 0 0 R/W 0 offset_x<3:0> offset value, which is subtracted from the internal filtered and unfiltered xaxis acceleration data; the offset value is represented with two's complement notation, with a mapping of +127 +0.992g, 0 0 g, and -128 -1 g; the scaling is independent of the selected g-range; the content of the offset_x<7:0> may be written to the NVM; it is automatically restored from the NVM after each power-on or softreset; offset_x<7:0> may be written directly by the user; it is generated automatically after triggering the fast offset compensation procedure for the x-axis BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 101 Register 0x39 (OFC_OFFSET_Y) Contains the offset compensation value for y-axis acceleration readout data. Name Bit Read/Write Reset Value Content 0x39 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 offset_y<7:0>: 6 R/W 0 OFC_OFFSET_Y 5 R/W 0 4 R/W 0 offset_y<7:4> 2 R/W 0 1 R/W 0 0 R/W 0 offset_y<3:0> offset value, which is subtracted from the internal filtered and unfiltered yaxis acceleration data; the offset value is represented with two's complement notation, with a mapping of +127 +0.992g, 0 0 g, and -128 -1 g; the scaling is independent of the selected g-range; the content of the offset_y<7:0> may be written to the NVM; it is automatically restored from the NVM after each power-on or softreset; offset_y<7:0> may be written directly by the user; it is generated automatically after triggering the fast offset compensation procedure for the y-axis Register 0x3A (OFC_OFFSET_Z) Contains the offset compensation value for z-axis acceleration readout data. Name Bit Read/Write Reset Value Content 0x3A 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 offset_z<7:0>: 6 R/W 0 OFC_OFFSET_Z 5 R/W 0 4 R/W 0 offset_z<7:4> 2 R/W 0 1 R/W 0 0 R/W 0 offset_z<3:0> offset value, which is subtracted from the internal filtered and unfiltered zaxis acceleration data; the offset value is represented with two's complement notation, with a mapping of +127 +0.992g, 0 0 g, and -128 -1 g; the scaling is independent of the selected g-range; the content of the offset_z<7:0> may be written to the NVM; it is automatically restored from the NVM after each power-on or softreset; offset_z<7:0> may be written directly by the user; it is generated automatically after triggering the fast offset compensation procedure for the z-axis BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 102 6.16 Non-volatile memory back-up Register 0x3B (TRIM_GP0) Contains general purpose data register with NVM back-up. Name Bit Read/Write Reset Value Content 0x3B 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 GP0<7:0>: TRIM_GP0 5 R/W 0 6 R/W 0 4 R/W 0 GP0<7:4> 2 R/W 0 1 R/W 0 0 R/W 0 GP0<3:0> general purpose NVM image register not linked to any sensor-specific functionality; register may be written to NVM and is restored after each power-up or softreset Register 0x3C (TRIM_GP1) Contains general purpose data register with NVM back-up. Name Bit Read/Write Reset Value Content 0x3C 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 GP1<7:0>: 6 R/W 0 TRIM_GP1 5 R/W 0 4 R/W 0 GP1<7:4> 2 R/W 0 1 R/W 0 0 R/W 0 GP1<3:0> general purpose NVM image register not linked to any sensor-specific functionality; register may be written to NVM and is restored after each power-up or softreset BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 103 6.17 FIFO configuration and FIFO data Register 0x30 (FIFO_CONFIG_0) Contains the FIFO watermark level. Name Bit Read/Write Reset Value Content Bit Read/Write Reset Value Content 0x30 7 R/W n/a 6 R/W n/a FIFO_CONFIG_0 5 R/W 0 Reserved 3 R/W 0 4 R/W 0 fifo_water_mark_level_trigger_ retain<5:4> 2 R/W 0 1 R/W 0 0 R/W 0 fifo_water_mark_level_trigger_retain<3:0> reserved: write `0' fifo_water_mark_level_trigger_retain<5:0>: fifo_water_mark_level_trigger_retain<5:0> defines the FIFO watermark level. An interrupt will be generated, when the number of entries in the FIFO is equal to fifo_water_mark_level_trigger_retain<5:0>; Register 0x3E (FIFO_CONFIG_1) Contains FIFO configuration settings. The FIFO buffer memory is cleared and the fifo-full flag is cleared when writing to FIFO_CONFIG_1 register. Name Bit Read/Write Reset Value Content 0x3E 7 R/W 0 Bit Read/Write Reset Value Content 3 R/W 0 fifo_mode<1:0>: 6 R/W 0 FIFO_CONFIG_1 5 R/W 0 fifo_mode<1:0> Reserved 2 R/W 0 Reserved 4 R/W 0 1 R/W 0 0 R/W 0 fifo_data_select<1:0> selects the FIFO operating mode: 00b BYPASS (buffer depth of 1 frame; old data is discarded), 01b FIFO (data collection stops when buffer is filled with 32 frames), 10b STREAM (sampling continues when buffer is full; old is discarded), 11b reserved, do not use BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 104 fifo_data_select<1:0>: selects whether 00b X+Y+Z, 01b X only, 10b Y only, 11b Z only acceleration data are stored in the FIFO. Register 0x3F (FIFO_DATA) FIFO data readout register. The format of the LSB and MSB components corresponds to that of the acceleration data readout registers. The new data flag is preserved. Read burst access may be used since the address counter will not increment when the read burst is started at the address of FIFO_DATA. The entire frame is discarded when a fame is only partially read out. Name Bit Read/Write Reset Value Content 0x3F 7 R n/a Bit Read/Write Reset Value Content 3 R n/a 6 R n/a FIFO_DATA 5 R n/a 4 R n/a fifo_data_output_register<7:4> 2 R n/a 1 R n/a 0 R n/a fifo_data_output_register<3:0> fifo_data_output_register<7:0>: FIFO data readout; data format depends on the setting of register fifo_data_select<1:0>: if X+Y+Z data are selected, the data of frame n is reading out in the order of X-lsb(n), X-msb(n), Y-lsb(n), Y-msb(n), Z-lsb(n), Z-msb(n); if X-only is selected, the data of frame n and n+1 are reading out in the order of X-lsb(n), X-msb(n), X-lsb(n+1), X-msb(n+1); the Y-only and Z-only modes behave analogously BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 105 7. Magnetometer register description 7.1 General remarks The entire communication with the device's magnetometer part is performed by reading from and writing to registers. Registers have a width of 8 bits; they are mapped to a common space of 50 addresses from (0x40) up to (0x71). Within the used range there are several registers which are marked as `reserved'. Any reserved bit is ignored when it is written and no specific value is guaranteed when read. Especially, in SPI mode the SDO pin may stay in high-Z state when reading some of these registers. Registers with addresses from (0x40) up to (0x4A) are read-only. Any attempt to write to these registers is ignored. 7.2 Register map Register Address 0x71 0x70 0x6F 0x6E 0x6D 0x6C 0x6B 0x6A 0x69 0x68 0x67 0x66 0x65 0x64 0x63 0x62 0x61 0x60 0x5F 0x5E 0x5D 0x5C 0x5B 0x5A 0x59 0x58 0x57 0x56 0x55 0x54 0x53 0x52 0x51 0x50 0x4F 0x4E 0X4D 0x4C 0x4B 0x4A 0x49 0x48 0x47 0x46 0x45 0x44 0x43 0x42 0x41 0x40 Default Value N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 0x00 0x00 0x00 0x00 0x07 0x3F 0x06 0x01 0x00 N/A N/A N/A N/A N/A N/A N/A N/A N/A 0x32 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved Data Ready Pin En Interrupt Pin En Overflow Int En Data Overrun En Adv. ST [1:0] Soft Reset '1' fixed '0' Data Overrun Overflow REPZ Number Of Repetitions (valid for Z) [7:0] REPXY Number Of Repetitions (valid for XY) [7:0] High Threshold [7:0] Low Threshold [7:0] Channel Z Channel Y Channel X High Int Z en High Int Y en High Int X en Data Rate [2:0] fixed '0' fixed '0' fixed '0' High Int Z High Int Y High Int X RHALL [13:6] MSB RHALL [5:0] LSB DATA Z [14:7] MSB DATA Z [6:0] LSB DATA Y [12:5] MSB DATA Y [4:0] LSB DATA X [12:5] MSB DATA X [4:0] LSB reserved Chip ID = 0x32 (can only be read if power control bit ="1") DR Polarity Interrupt Latch Low Int Z en Low Int Y en Opmode [1:0] SPI3en Soft Reset '1' Low Int Z Low Int Y Interrupt Polarity Low Int X en Self Test Power Control Bit Low Int X fixed '0' Data Ready Status fixed '0' fixed '0' Y-Self-Test fixed '0' fixed '0' X-Self-Test Z-Self-Test w/r w/r accessible in suspend mode read only reserved BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 106 7.3 Chip ID Register (0x40) Chip ID contains the magnetometer chip identification number, which is 0x32. This number can only be read if the power control bit (register 0x4B bit0) is enabled. Table 25: Chip identification number, register (0x40) Bit 7 0 Bit 6 0 Bit 5 1 Bit 4 1 Bit 3 0 Bit 2 0 Bit 1 1 Bit 0 0 Register (0x41) is reserved 7.4 Magnetic field data Register (0x42) contains the LSB part of x-axis magnetic field data and the self-test result flag for the x-axis. Table 26: LSB part of x-axis magnetic field, register (0x42) (0x42) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAX_lsb <4> DATAX_lsb <3> DATAX_lsb <2> DATAX_lsb <1> DATAX_lsb <0> SelfTestX Description Bit 4 of x-axis magnetic field data Bit 3 of x-axis magnetic field data Bit 2 of x-axis magnetic field data Bit 1 of x-axis magnetic field data Bit 0 of x-axis magnetic field data = x LSB (fixed to 0) (fixed to 0) Self-test result flag for x-axis, default is "1" Register (0x43) contains the MSB part of x-axis magnetic field data. Table 27: MSB part of x-axis magnetic field, register (0x43) (0x43) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAX_msb <12> DATAX_msb <11> DATAX_msb <10> DATAX_msb <9> DATAX_msb <8> DATAX_msb <7> DATAX_msb <6> DATAX_msb <5> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Bit 12 of x-axis magnetic field data = x MSB Bit 11 of x-axis magnetic field data Bit 10 of x-axis magnetic field data Bit 9 of x-axis magnetic field data Bit 8 of x-axis magnetic field data Bit 7 of x-axis magnetic field data Bit 6 of x-axis magnetic field data Bit 5 of x-axis magnetic field data Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 107 Register (0x44) contains the LSB part of y-axis magnetic field data and the self-test result flag for the y-axis. Table 28: LSB part of y-axis magnetic field, register (0x44) (0x44) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAY_lsb <4> DATAY_lsb <3> DATAY_lsb <2> DATAY_lsb <1> DATAY_lsb <0> SelfTestY Description Bit 4 of y-axis magnetic field data Bit 3 of y-axis magnetic field data Bit 2 of y-axis magnetic field data Bit 1 of y-axis magnetic field data Bit 0 of y-axis magnetic field data = y LSB (fixed to 0) (fixed to 0) Self-test result flag for y-axis, default is "1" Register (0x45) contains the MSB part of y-axis magnetic field data. Table 29: MSB part of y-axis magnetic field, register (0x45) (0x45) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAY_msb <12> DATAY_msb <11> DATAY_msb <10> DATAY_msb <9> DATAY_msb <8> DATAY_msb <7> DATAY_msb <6> DATAY_msb <5> Description Bit 12 of y-axis magnetic field data = y MSB Bit 11 of y-axis magnetic field data Bit 10 of y-axis magnetic field data Bit 9 of y-axis magnetic field data Bit 8 of y-axis magnetic field data Bit 7 of y-axis magnetic field data Bit 6 of y-axis magnetic field data Bit 5 of y-axis magnetic field data Register (0x46) contains the LSB part of z-axis magnetic field data and the self-test result flag for the z-axis. Table 30: LSB part of z-axis magnetic field, register (0x46) (0x46) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAZ_lsb <6> DATAZ_lsb <5> DATAZ_lsb <4> DATAZ_lsb <3> DATAZ_lsb <2> DATAZ_lsb <1> DATAZ_lsb <0> SelfTestZ BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Bit 6 of z-axis magnetic field data Bit 5 of z-axis magnetic field data Bit 4 of z-axis magnetic field data Bit 3 of z-axis magnetic field data Bit 2 of z-axis magnetic field data Bit 1 of z-axis magnetic field data Bit 0 of z-axis magnetic field data = z LSB Self-test result flag for z-axis, default is "1" Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 108 Register (0x47) contains the MSB part of z-axis magnetic field data. Table 31: MSB part of z-axis magnetic field, register (0x47) (0x47) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name DATAZ_msb <14> DATAZ_msb <13> DATAZ_msb <12> DATAZ_msb <11> DATAZ_msb <10> DATAZ_msb <9> DATAZ_msb <8> DATAZ_msb <7> Description Bit 14 of y-axis magnetic field data = z MSB Bit 13 of y-axis magnetic field data Bit 12 of y-axis magnetic field data Bit 11 of y-axis magnetic field data Bit 10 of y-axis magnetic field data Bit 9 of y-axis magnetic field data Bit 8 of y-axis magnetic field data Bit 7 of y-axis magnetic field data Register (0x48) contains the LSB part of hall resistance and the Data Ready (DRDY) status bit. Table 32: LSB part of hall resistance, register (0x48) (0x48) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name RHALL_lsb <5> RHALL_lsb <4> RHALL_lsb <3> RHALL_lsb <2> RHALL_lsb <1> RHALL_lsb <0> Data Ready Status Description Bit 5 of hall resistance Bit 4 of hall resistance Bit 3 of hall resistance Bit 2 of hall resistance Bit 1 of hall resistance Bit 0 of hall resistance = RHALL LSB (fixed to 0) Data ready (DRDY) status bit Register (0x49) contains the MSB part of hall resistance. Table 33: MSB part of hall resistance, register (0x49) (0x49) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name RHALL_msb <13> RHALL_msb <12> RHALL_msb <11> RHALL_msb <10> RHALL_msb <9> RHALL_msb <8> RHALL_msb <7> RHALL_msb <6> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Bit 13 of hall resistance = RHALL MSB Bit 12 of hall resistance Bit 11 of hall resistance Bit 10 of hall resistance Bit 9 of hall resistance Bit 8 of hall resistance Bit 7 of hall resistance Bit 6 of hall resistance Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 109 7.5 Interrupt status register Register (0x4A) contains the states of all magnetometer interrupts. Table 34: Interrupt status, register (0x4A) (0x4A) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Data overrun Overflow High Int Z High Int Y High Int X Low Int Z Low Int Y Low Int X BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Data overrun status flag Overflow status flag High-Threshold interrupt z-axis status flag High-Threshold interrupt y-axis status flag High-Threshold interrupt x-axis status flag Low-Threshold interrupt z-axis status flag Low-Threshold interrupt y-axis status flag Low-Threshold interrupt x-axis status flag Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 110 7.6 Power and operation modes, self-test and data output rate control registers Register (0x4B) contains control bits for power control, soft reset and interface SPI mode selection. This special control register is also accessible in suspend mode. Soft reset is executed when both bits (register 0x4B bit7 and bit1) are set "1". Soft reset does not execute a full POR sequence, but all registers are reset except for the "trim" registers above register 0x54 and the power control register (0x4B). Soft reset always brings the device into sleep mode. When device is in the suspend mode, soft reset is ignored and the device remains in suspend mode. The two "Soft Reset" bits are reset to "0" automatically after soft reset was completed. To perform a full POR reset, bring the device into suspend and then back into sleep mode. When SPI mode is selected, the "SPI3En" bit enables SPI 3-wire mode when set "1". When "SPI3En" is set "0" (default), 4-wire SPI mode is selected. Setting the "Power Control bit" to "1" brings the device up from Suspend mode to Sleep mode, when "Power Control bit" is set "0" the device returns to Suspend mode (see chapter 4.2.2 for details of magnetometer power modes). Table 35: Power control, soft reset and SPI mode control register (0x4B) (0x4B) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Soft Reset `1' SPI3en Soft Reset `1' Power Control bit BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description One of the soft reset trigger bits. (fixed to 0) (fixed to 0) (fixed to 0) (fixed to 0) Enable bit for SPI3 mode One of the soft reset trigger bits. When set to "0", suspend mode is selected Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 111 Register (0x4C) contains control bits for operation mode, output data rate and self-test. The two "Adv. ST" bits control the on-chip advanced self-test (see chapter 4.4.2 for details of the magnetometer advanced self-test). The three "Data rate" bits control the magnetometer output data rate according to below Table 37. The two "Opmode" bits control the operation mode according to below Table 38 (see chapter 4.2.2 for a detailed description of magnetometer power modes). Table 36: Operation mode, output data rate and self-test control register (0x4C) (0x4C) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Adv. ST <1> Adv. ST <0> Data rate <2> Data rate <1> Data rate <0> Opmode <1> Opmode <0> Self Test Description Advanced self-test control bit 1 Advanced self-test control bit 0 Data rate control bit 2 Data rate control bit 1 Data rate control bit 0 Operation mode control bit 1 Operation mode control bit 0 Normal self-test control bit Three "Data rate" bits control the output data rate (ODR) of the BMC150 magnetometer part: Table 37: Output data rate (ODR) setting (0x4C) (0x4C) Data rate <2:0> 000b 001b 010b 011b 100b 101b 110b 111b Magnetometer output data rate (ODR) [Hz] 10 (default) 2 6 8 15 20 25 30 Two "Opmode" bits control the operation mode of the BMC150 magnetometer part: Table 38: Operation mode setting (0x4C) (0x4C) Opmode <1:0> 00b 01b 10b 11b 8 Magnetometer operation mode8 Normal mode Forced mode Reserved, do not use Sleep Mode See chapter 4.2.2 for a detailed description of magnetometer power modes. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 112 7.7 Interrupt and axis enable settings control registers Register (0x4D) contains control bits for interrupt settings. (Also refer to chapter 0 for the details of magnetometer interrupt operation). Table 39: Interrupt settings control register (0x4D) (0x4D) Bit Bit 7 Name Data Overrun En Bit 6 Overflow Int En Bit 5 High Int Z En Bit 4 High Int Y En Bit 3 High Int X En Bit 2 Low Int Z En Bit 1 Low Int Y En Bit 0 Low Int X En BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Enables data overrun indication in the "Data Overrun" flag (active high, default is "0" disabled) Activates mapping of Overflow flag status to the INT3 pin (active high, default is "0" disabled) Enables the z-axis detection for High-Threshold interrupts (active low, default is "1" disabled) Enables the y-axis detection for High-Threshold interrupts (active low, default is "1" disabled) Enables the x-axis detection for High-Threshold interrupts (active low, default is "1" disabled) Enables the z-axis detection for Low-Threshold interrupts (active low, default is "1" disabled) Enables the y-axis detection for Low-Threshold interrupts (active low, default is "1" disabled) Enables the x-axis detection for Low-Threshold interrupts (active low, default is "1" disabled) Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 113 Register (0x4E) contains control bits interrupt settings and axes enable bits. (Also refer to chapter 0 for the details of magnetometer interrupt operation). If a magnetic measurement channel is disabled, its last measured magnetic output values will remain in the data registers. If the Z channel is disabled, the resistance measurement will also be disabled and the resistance output value will be set to zero. If interrupts are set to trigger on an axis that has been disabled, these interrupts will still be asserted based on the last measured value. Table 40: Interrupt settings and axes enable bits control register (0x4E) (0x4E) Bit Name Bit 7 Data Ready Pin En Bit 6 Interrupt Pin En Bit 5 Channel Z Bit 4 Channel Y Bit 3 Channel X Bit 2 DR Polarity Bit 1 Interrupt Latch Bit 0 Interrupt Polarity Description Enables data ready status mapping on DRDY pin (active high, default is "0" disabled) Enables interrupt status mapping on INT3 pin (active high, default is "0" disabled) Enable z-axis and resistance measurement (active low, default is "0" enabled) Enable y-axis (active low, default is "0" enabled) Enable x-axis (active low, default is "0" enabled) Data ready (DRDY) pin polarity ("0" is active low, "1" is active high, default is "1" active high) Interrupt latching ("0" means non-latched - interrupt pin is on as long as the condition is fulfilled, "1" means latched - interrupt pin is on until interrupt status register 0x4A is read, default is `"1" latched) Interrupt pin INT3 polarity selection ("1" - is active high, "0" is active low, default is "1" active high) Register (0x4F) contains the Low-Threshold interrupt threshold setting. (Also refer to chapter 0 for the details of magnetometer interrupt operation and the threshold setting). Table 41: Low-threshold interrupt threshold setting control register (0x4F) (0x4F) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name LowThreshold <7> LowThreshold <6> LowThreshold <5> LowThreshold <4> LowThreshold <3> LowThreshold <2> LowThreshold <1> LowThreshold <0> BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description Bit 7 of Low-Threshold interrupt threshold setting Bit 6 of Low-Threshold interrupt threshold setting Bit 5 of Low-Threshold interrupt threshold setting Bit 4 of Low-Threshold interrupt threshold setting Bit 3 of Low-Threshold interrupt threshold setting Bit 2 of Low-Threshold interrupt threshold setting Bit 1 of Low-Threshold interrupt threshold setting Bit 0 of Low-Threshold interrupt threshold setting Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 114 Register (0x50) contains the High-Threshold interrupt threshold setting. (Also refer to chapter 0 for the details of magnetometer interrupt operation and the threshold setting). Table 42: High-threshold interrupt threshold setting control register (0x4F) (0x50) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name HighThreshold <7> HighThreshold <6> HighThreshold <5> HighThreshold <4> HighThreshold <3> HighThreshold <2> HighThreshold <1> HighThreshold <0> Description Bit 7 of High-Threshold interrupt threshold setting Bit 6 of High-Threshold interrupt threshold setting Bit 5 of High-Threshold interrupt threshold setting Bit 4 of High-Threshold interrupt threshold setting Bit 3 of High-Threshold interrupt threshold setting Bit 2 of High-Threshold interrupt threshold setting Bit 1 of High-Threshold interrupt threshold setting Bit 0 of High-Threshold interrupt threshold setting 7.8 Number of repetitions control registers Register (0x51) contains the number of repetitions for x/y-axis. Table 44 below shows the number of repetitions resulting out of the register configuration. The performed number of repetitions nXY can be calculated from unsigned register value as nXY = 1+2xREPXY as shown below, where b7-b0 are the bits 7 to 0 of register 0x51: nXY 1 2 (b 7 2 7 b 6 2 6 b 5 2 5 b 4 2 4 b 3 2 3 b 2 2 2 b1 21 b 0 2 0 ) 1 2 (REPXY ) Table 43: x/y-axis repetitions control register (0x51) (0x51) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name REPXY <7> REPXY <6> REPXY <5> REPXY <4> REPXY <3> REPXY <2> REPXY <1> REPXY <0> Description Bit 7 of number of repetitions (valid for XY) Bit 6 of number of repetitions (valid for XY) Bit 5 of number of repetitions (valid for XY) Bit 4 of number of repetitions (valid for XY) Bit 3 of number of repetitions (valid for XY) Bit 2 of number of repetitions (valid for XY) Bit 1 of number of repetitions (valid for XY) Bit 0 of number of repetitions (valid for XY) Table 44: Numbers of repetition for x/y-axis depending on value of register (0x51) (0x51) register value (binary) 00000000b 00000001b 00000010b 00000011b ... 11111111b (0x51) value (hex) register Number of repetitions for x- and y-axis each 0x00h 0x01h 0x02h 0x03h 0xFFh BST-BMC150-DS000-04 | Revision 1.0 | July 2014 1 3 5 7 ... 511 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 115 Register (0x52) contains the number of repetitions for z-axis. Table 46 below shows the number of repetitions resulting out of the register configuration. The performed number of repetitions nZ can be calculated from unsigned register value as nZ = 1+REPZ as shown below, where b7-b0 are the bits 7 to 0 of register 0x52: nZ 1 1 (b 7 27 b 6 26 b 5 25 b 4 24 b 3 23 b 2 22 b1 21 b 0 20 ) 1 REPZ Table 45: Z-axis repetitions control register (0x52) (0x52) Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name REPZ <7> REPZ <6> REPZ <5> REPZ <4> REPZ <3> REPZ <2> REPZ <1> REPZ <0> Description Bit 7 of number of repetitions (valid for Z) Bit 6 of number of repetitions (valid for Z) Bit 5 of number of repetitions (valid for Z) Bit 4 of number of repetitions (valid for Z) Bit 3 of number of repetitions (valid for Z) Bit 2 of number of repetitions (valid for Z) Bit 1 of number of repetitions (valid for Z) Bit 0 of number of repetitions (valid for Z) Table 46: Numbers of repetition for z-axis depending on value of register (0x52) (0x52) register value (binary) 00000000b 00000001b 00000010b 00000011b ... 11111111b (0x52) register value (hex) Number of repetitions for z-axis 0x00h 0x01h 0x02h 0x03h 1 2 3 4 ... 256 0xFFh BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 116 8. Digital interfaces The BMC150 supports two serial digital interface protocols for communication as a slave with a host device for each of the accelerometer and magnetometer part: SPI and IC. Accelerometer part and magnetometer part alone operate either both in IC mode or either both in SPI mode, mixed communication protocols are not possible because the interface pins are shared. The active interface is selected by the state of the "protocol select" pin (PS): "0" ("1") selects SPI (IC). By default, SPI operates in the standard 4-wire configuration. It can be re-configured by software to work in 3-wire mode instead of standard 4-wire mode for both the accelerometer part and magnetometer part. Both interfaces share the same pins. The mapping for each interface is given in the following table: Table 47: Mapping of the interface pins Pin# 1 14 Name SDO SDI use w/ SPI use w/ IC SDO Accelerometer and magnetometer part IC address selection SDI SDA 12 CSB CSB Magnetometer part IC address selection 11 SCK SCK SCL BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Description SPI: Data Output (4-wire mode) IC: Used to set LSB of IC address of accelerometer part and magnetometer part SPI: Data Input (4-wire mode) Data Input / Output (3-wire mode) IC: Serial Data SPI: Chip Select for accelerometer and magnetometer part (enable) IC: Used to set bit1 of IC address of magnetometer part, always high in I2C mode SPI: Serial Clock IC: Serial Clock Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 117 The following table shows the electrical specifications of the interface pins: Table 48: Electrical specification of the interface pins Parameter Symbol Pull-up Resistance Rup,SPI CSB in SPI mode Pull-up Resistance Rup,I2C CSB in I2C mode Input Capacitance Condition Internal Pull-up Resistance to VDDIO Internal Pull-up Resistance to VDDIO Min Typ Max Unit 37 55 74 k 70 120 190 k 20 pF 400 pF Cin IC Bus Load Capacitance (max. CI2C_Load drive capability) 8.1 Serial peripheral interface (SPI) The timing specification for SPI of the BMC150 is given in the following table: Table 49: SPI timing for BMC150 accelerometer and magnetometer part Parameter Clock Frequency SCK Low Pulse SCK High Pulse SDI Setup Time SDI Hold Time SDO Output Delay CSB Setup Time CSB Hold Time Idle time between write accesses, normal mode, standby mode, low-power mode 2 Idle time between write accesses, suspend mode, lowpower mode 1 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Symbol Condition fSPI Max Units Max. Load on SDI or SDO = 25pF, VDDIO 1.62V 10 MHz VDDIO < 1.62V 7.5 MHz tSCKL tSCKH 20 20 20 20 tSDI_setup tSDI_hold tSDO_OD Min Load = 25pF, VDDIO 1.62V Load = 25pF, VDDIO < 1.62V Load = 250pF, VDDIO > 2.4V ns ns ns ns 30 ns 50 ns 40 ns tCSB_setup tCSB_hold 20 40 ns ns tIDLE_wacc_nm 2 s tIDLE_wacc_sum 450 s Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 118 The following figure shows the definition of the SPI timings given in Table 49: tCSB_setup tCSB_hold CSB SCK tSCKL tSCKH SDI SDO tSDI_setup tSDI_hold tSDO_OD Figure 19: SPI timing diagram The SPI interface of the BMC150 is compatible with two modes, "00" and "11". The automatic selection between [CPOL = "0" and CPHA = "0"] and [CPOL = "1" and CPHA = "1"] is done based on the value of SCK after a falling edge of CSB. Two configurations of the SPI interface are supported by the BMC150: 4-wire and 3-wire. The same protocol is used by both configurations. The device operates in 4-wire configuration by default. It can be switched to 3-wire configuration by writing "1" to (0x34) "spi3" for the accelerometer part and writing "1" to (0x4B) "SPI3en" for the magnetometer part (after power control bit was set). Pin SDI is used as the common data pin in 3-wire configuration. For single byte read as well as write operations, 16-bit protocols are used. The BMC150 also supports multiple-byte read operations. In SPI 4-wire configuration CSB (chip select low active), SCK (serial clock), SDI (serial data input), and SDO (serial data output) pins are used. The communication starts when the CSB is pulled low by the SPI master and stops when CSB is pulled high. SCK is also controlled by SPI master. SDI and SDO are driven at the falling edge of SCK and should be captured at the rising edge of SCK. The basic write operation waveform for 4-wire configuration is depicted in Figure 20. During the entire write cycle SDO remains in high- impedance state. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 119 CSB SCK SDI R/W AD6 AD5 AD4 AD3 AD2 AD1 AD0 SDO DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 Z tri-state Figure 20: 4-wire basic SPI write sequence (mode "11") The basic read operation waveform for 4-wire configuration is depicted in Figure 21: CS B SC K SD I R/W AD 6 AD5 A 4 D A 3 A 2 D D AD 1 AD 0 SD O DO 7 DO 6 DO 5 DO 4 DO 3 DO 2 DO 1 DO tr -stat 0 i e Figure 21: 4-wire basic SPI read sequence (mode "11") The data bits are used as follows: Bit0: Read/Write bit. When 0, the data SDI is written into the chip. When 1, the data SDO from the chip is read. Bit1-7: Address AD(6:0). Bit8-15: when in write mode, these are the data SDI, which will be written into the address. When in read mode, these are the data SDO, which are read from the address. Multiple read operations are possible by keeping CSB low and continuing the data transfer. Only the first register address has to be written. Addresses are automatically incremented after each read access as long as CSB stays active low. Note that a complete burst read over accelerometer and magnetometer register addresses is not supported. Instead, a second burst read must be started at address 0x40 if the entire BMC150 memory map is to be read. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 120 The principle of multiple read is shown in Figure 22: Control byte Start RW CSB = 0 1 Register adress (02h) 0 0 0 0 0 1 0 X X Data byte Data byte Data byte Data register - adress 02h Data register - adress 03h Data register - adress 04h X X X X X X X X X X X X X X X X X X X X Stop X X CSB = 1 Figure 22: SPI multiple read In SPI 3-wire configuration CSB (chip select low active), SCK (serial clock), and SDI (serial data input and output) pins are used. The communication starts when the CSB is pulled low by the SPI master and stops when CSB is pulled high. SCK is also controlled by SPI master. SDI is driven (when used as input of the device) at the falling edge of SCK and should be captured (when used as the output of the device) at the rising edge of SCK. The protocol as such is the same in 3-wire configuration as it is in 4-wire configuration. The basic operation waveform (read or write access) for 3-wire configuration is depicted in Figure 23: CSB SCK SDI RW AD6 AD5 AD4 AD3 AD2 AD1 AD0 DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 Figure 23: 3-wire basic SPI read or write sequence (mode "11") BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 121 8.2 Inter-Integrated Circuit (IC) The IC bus uses SCL (= SCK pin, serial clock) and SDA (= SDI pin, serial data input and output) signal lines. Both lines must be connected to VDDIO externally via pull-up resistors so that they are pulled high when the bus is free. The IC interface of the BMC150 is compatible with the IC Specification UM10204 Rev. 03 (19 June 2007), available at http://www.nxp.com. The BMC150 supports IC standard mode and fast mode, only 7-bit address mode is supported. An overview is given in the table below: Table 50: BMC150 IC addresses CSB pin SDO pin VDDIO VDDIO GND VDDIO BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Accelerometer part IC address 0x10 0x11 Magnetometer part IC address 0x12 0x13 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 122 The timing specification for IC of the BMC150 is given in: Table 51: IC timings Parameter Clock Frequency SCL Low Period SCL High Period SDA Setup Time SDA Hold Time Setup Time for a repeated Start Condition Hold Time for a Start Condition Setup Time for a Stop Condition Time before a new Transmission can start Idle time between write accesses, normal mode, standby mode, low-power mode 2 Idle time between write accesses, suspend mode, lowpower mode 1 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Symbol fSCL tLOW tHIGH tSUDAT tHDDAT Condition Min Max 400 Units kHz 1.3 0.6 0.1 0.0 tSUSTA 0.6 tHDSTA 0.6 tSUSTO 0.6 s tBUF tIDLE_wacc_n m tIDLE_wacc_s um 1.3 2 450 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 123 Below Figure shows the definition of the IC timings given in Table 51: IC timings: SD A tBUF tf t LOW SC L tHIGH tHDSTA tr tHDDAT t SUDAT SD A tSUSTA t SUSTO Figure 24: IC timing diagram BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 124 The IC protocol works as follows: START: Data transmission on the bus begins with a HIGH to LOW transition on the SDA line while SCL is held HIGH (start condition (S) indicated by IC bus master). Once the START signal is transferred by the master, the bus is considered busy. STOP: Each data transfer should be terminated by a Stop signal (P) generated by master. The STOP condition is a LOW to HIGH transition on SDA line while SCL is held HIGH. ACK: Each byte of data transferred must be acknowledged. It is indicated by an acknowledge bit sent by the receiver. The transmitter must release the SDA line (no pull down) during the acknowledge pulse while the receiver must then pull the SDA line low so that it remains stable low during the high period of the acknowledge clock cycle. In the following diagrams these abbreviations are used: S P ACKS ACKM NACKM RW Start Stop Acknowledge by slave Acknowledge by master Not acknowledge by master Read / Write A START immediately followed by a STOP (without SCK toggling from logic "1" to logic "0") is not supported. If such a combination occurs, the STOP is not recognized by the device. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 125 IC write access: IC write access can be used to write a data byte in one sequence. The sequence begins with start condition generated by the master, followed by 7 bits slave address and a write bit (RW = 0). The slave sends an acknowledge bit (ACK = 0) and releases the bus. Then the master sends the one byte register address. The slave again acknowledges the transmission and waits for the 8 bits of data which shall be written to the specified register address. After the slave acknowledges the data byte, the master generates a stop signal and terminates the writing protocol. Example of an IC write access: Control byte Slave Adress Start S 0 0 1 0 0 Register adress (0x10) RW ACKS 0 0 0 Data byte 0 0 0 1 0 0 Data (0x09) ACKS 0 0 X X X X X ACKS Stop X X X P Figure 25: Example of an IC write access IC read access: IC read access also can be used to read one or multiple data bytes in one sequence. A read sequence consists of a one-byte IC write phase followed by the IC read phase. The two parts of the transmission must be separated by a repeated start condition (Sr). The IC write phase addresses the slave and sends the register address to be read. After slave acknowledges the transmission, the master generates again a start condition and sends the slave address together with a read bit (RW = 1). Then the master releases the bus and waits for the data bytes to be read out from slave. After each data byte the master has to generate an acknowledge bit (ACK = 0) to enable further data transfer. A NACKM (ACK = 1) from the master stops the data being transferred from the slave. The slave releases the bus so that the master can generate a STOP condition and terminate the transmission. The register address is automatically incremented and, therefore, more than one byte can be sequentially read out. Once a new data read transmission starts, the start address will be set to the register address specified in the latest IC write command. By default the start address is set at 0x00. In this way repetitive multi-bytes reads from the same starting address are possible. In order to prevent the IC slave of the device to lock-up the IC bus, a watchdog timer (WDT) is implemented in the accelerometer part of BMC150. The WDT observes internal IC signals and resets the IC interface if the bus is locked-up by the BMC150 accelerometer part. The activity and the timer period of the WDT can be configured through the bits (0x34) i2c_wdt_en and (0x34) i2c_wdt_sel. Writing 1 (0") to (0x34) i2c_wdt_en activates (de-activates) the WDT. Writing "0" ("1") to (0x34) i2c_wdt_se selects a timer period of 1 ms (50 ms). BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 126 Example of an IC multiple read accesses: Data byte Slave Adress Start Sr 0 0 1 0 0 Read Data (0x02) RW ACKS 0 0 1 Data byte X X X X X X Read Data (0x03) ACKM X X X X X Data byte X ... X X X X X X X X X X X X X X X X X Data byte Data byte Read Data (0x07) X X ... X Read Data (0x05) ACKM Read Data (0x06) X X Data byte Read Data (0x04) ... X ACKM X ACKM X X X X X X X X ACKM X ... X NACK X X Stop P Figure 26: Example of an IC multiple read access 8.2.1 SPI and IC Access Restrictions In order to allow for the correct internal synchronisation of data written to the BMC150 accelerometer, certain access restrictions apply for consecutive write accesses or a write/read sequence through the SPI as well as I2C interface. The required waiting period depends on whether the device is operating in normal mode (or standby mode, or low-power mode 2) or suspend mode (or low-power mode 1). As illustrated in figure 21, an interface idle time of at least 2 s is required following a write operation when the device operates in normal mode (or standby mode, or low-power mode 2). In suspend mode (or low-power mode 1) an interface idle time of least 450 s is required. X-after-Write Write-Operation X-Operation Register Update Period (> 2us / 450us) Figure 27: Post-Write Access Timing Constraints For the magnetometer, only the power control bit can be accessed in suspend mode. After setting power control to `1', the user must wait ts_up,m before the other registers can be accessed. These can then be accessed without any restrictions. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 127 9. Pin-out and connection diagram 9.1 Pin-out 14 SDI 13 PS 12 CSB 12 CSB 1 SDO 2 INT1 TOP VIEW (pads not visible) 3 INT2 4 DRDY 5 INT3 6 GND 11 SCK 11 SCK 10 VDDIO 10 VDDIO 9 GND 9 GND 8 VDD 8 VDD 7 GND 14 SDI 1 SDO BOTTOM VIEW (pads visible) 2 INT1 3 INT2 4 DRDY 7 GND Figure 28: Pin-out top view 13 PS 6 GND 5 INT3 Figure 29: Pin-out bottom view Table 52: Pin description Pin Name I/O Type Sensor Description 1 SDO Out Mag+Acc SPI: Data out 2 INT1 Out Acc 3 INT2 Out Acc 4 DRDY Out Mag 5 INT3 Out Mag 6 GND Supply Mag+Acc 7 GND Supply Mag+Acc 8 VDD Supply Mag+Acc 9 GND Supply 10 VDDIO 11 Interrupt output #1 Interrupt output #2 Data ready Interrupt output #3 Ground SPI4W SDO / MISO Connect to SPI3W IC DNC GND for (float) default address INT 1 input or DNC if unused INT2 input or DNC if unused DRDY input or DNC if unused INT3 input or DNC if unused GND GND Mag+Acc Ground Supply voltage Ground Supply Mag+Acc I/O voltage VDDIO SCK In Mag+Acc Serial clock SCK SCK 12 CSB In Mag+Acc Chip Select CSB CSB 13 PS In Mag+Acc GND GND VDDIO 14 SDI In/Out Mag+Acc SDI / MOSI SDA SDA BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Protocol select SPI: Data in, IC: Data VDD GND SCL DNC (float) or VDDIO Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 128 9.2 Connection diagram 4-wire SPI SDI 14 SDI VDDIO CSB 13 PS VDD 12 CSB SDO 1 SDO 11 SCK INT1 or NC 2 INT1 10 VDDIO INT2 or NC 3 INT2 DRDY or NC 4 DRDY TOP VIEW (pads not visible) SCK 9 GND 8 VDD 5 INT3 6 GND 7 GND C2 C1 INT3 or NC Figure 30: 4-wire SPI connection diagram Note: The recommended value for C1 and C2 is 100 nF. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 129 9.3 Connection diagram 3-wire SPI SDI/SDO 14 SDI VDDIO CSB 13 PS VDD 12 CSB 1 SDO 11 SCK INT1 or NC 2 INT1 10 VDDIO INT2 or NC 3 INT2 DRDY or NC 4 DRDY TOP VIEW (pads not visible) SCK 9 GND 8 VDD 5 INT3 6 GND 7 GND C2 C1 INT3 or NC Figure 31: 3-wire SPI connection diagram Note: The recommended value for C1 and C2 is 100 nF. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 130 9.4 Connection diagram I2C SDA 14 SDI VDDIO 13 PS VDD 12 CSB IC address bit 0 GND: 0; VDDIO: '1' 1 SDO 11 SCK INT1 or NC 2 INT1 10 VDDIO INT2 or NC 3 INT2 DRDY or NC 4 DRDY TOP VIEW (pads not visible) SCL 9 GND 8 VDD 5 INT3 6 GND 7 GND C2 C1 INT3 or NC Figure 32: IC connection diagram Note: The recommended value for C1 and C2 is 100 nF. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 131 10. Package 10.1 Outline dimensions The sensor housing is a standard LGA 2.2 x 2.2 14-lead package. Its dimensions are the following: Figure 33: Package outline dimensions BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 132 10.2 Sensing axes orientation The magnetic and acceleration sensing axes of the BMC150 are matching. If the sensor is accelerated in the indicated directions, the corresponding channel will deliver a positive acceleration signal (dynamic acceleration). If the sensor is at rest and the force of gravity is acting along the indicated directions, the output of the corresponding channel will be negative (static acceleration). If a positive magnetic field is applied in the indicated directions, the corresponding channel will deliver a positive acceleration signal. Example: If the sensor is at rest or at uniform motion in a gravitational and magnetic field according to the figure given below, the output signals are 0 g for the X acceleration channel, 0 T for the X magnetic channel 0 g for the Y acceleration channel, 0 T for the Y magnetic channel +1 g for the Z acceleration channel, -|B| for the Z magnetic channel N B S Figure 34: Orientation of sensing axes (acceleration and magnetic) Please note that the planet's North pole is a magnetic south pole. This means that when the BMC150's X axis points towards the North pole, the measured field will be negative. The following table lists all corresponding output signals on X, Y, and Z while the sensor is at rest or at uniform motion in a gravity field under assumption of a 2g range setting and a top down gravity and magnetic vector as shown above. Table 53: Output signals depending on sensor orientation Output Signal Y Output Signal Z BST-BMC150-DS000-04 | Revision 1.0 | July 2014 0g / 0LSB 0 T -1g / 256LSB +|B| T 0g / 0LSB 0 T +1g / 256LSB -|B| T 0g / 0LSB 0 T 0g / 0LSB 0 T 0g / 0LSB 0 T +1g / 256LSB -|B| T 0g / 0LSB 0 T upright upright Sensor Orientation (gravity vector = acceleration vector , magnetic vector ) Output Signal X -1g / 256LSB +|B| T 0g / 0LSB 0 T 0g / 0LSB 0 T 0g / 0LSB 0 T 0g / 0LSB 0 T 0g / 0LSB 0 T 0g / 0LSB 0 T +1g / 256LSB -|B| T -1g / 256LSB +|B| T Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 133 10.3 Android axes orientation The Android coordinate system is shown in Figure 35. The origin is in the lower-left corner with respect to the screen, with the X axis horizontal and pointing right, the Y axis vertical and pointing up and the Z axis pointing outside the front face of the screen. In this system, coordinates behind the screen have negative Z values. Figure 35: Android coordinate system Attitude terms are defined in the following way (see Figure 36): Heading / Azimuth - angle between the magnetic north direction and the Y axis, around the Z axis (0 to 360). 0 = North, 90 = East, 180 = South, 270 = West. Pitch - rotation around X axis (-180 to 180), with positive values when the z-axis moves toward the y-axis. Roll - rotation around Y axis (-90 to 90), with positive values when the x-axis moves toward the z-axis. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 134 Figure 36: Heading, pitch and roll in Android coordinate frame BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 135 10.4 Landing pattern recommendation For the design of the landing pattern, we recommend the following dimensioning: Figure 37: Landing patterns relative to the device pins, dimensions are in mm BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 136 10.5 Marking 10.5.1 Mass production devices Table 54: Marking of mass production samples Labeling CCC TL Name Symbol Remark First letter of second row T internal use Second letter of second row L internal use Lot counter CCC Numerical counter Pin 1 identifier 10.5.2 Engineering samples Table 55: Marking of engineering samples Labeling TXX Y+ Name Symbol Remark Product number T 1 alphanumeric digit, fixed to identify product type, T = "C" Engineering lot XX 2 alphanumerical digits to identify the engineering lot Sample Stage Y "A" for A-samples, "C" for C-samples Sample status Cx x = Numerical counter Pin 1 identifier BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 137 10.6 Soldering guidelines The moisture sensitivity level of the BMC150 sensors corresponds to JEDEC Level 1, see also: IPC/JEDEC J-STD-020C "Joint Industry Standard: Moisture/Reflow Sensitivity Classification for non-hermetic Solid State Surface Mount Devices" IPC/JEDEC J-STD-033A "Joint Industry Standard: Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices". The sensor fulfils the lead-free soldering requirements of the above-mentioned IPC/JEDEC standard, i.e. reflow soldering with a peak temperature up to 260C. Figure 38: Soldering profile BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 138 10.7 Handling instructions Micromechanical sensors are designed to sense acceleration with high accuracy even at low amplitudes and contain highly sensitive structures inside the sensor element. The MEMS sensor can tolerate mechanical shocks up to several thousand g. However, these limits might be exceeded in conditions with extreme shock loads such as e.g. hammer blow on or next to the sensor, dropping of the sensor onto hard surfaces etc. We recommend avoiding g-forces beyond the specified limits during transport, handling and mounting of the sensors in a defined and qualified installation process. This device has built-in protections against high electrostatic discharges or electric fields (e.g. 2kV HBM); however, anti-static precautions should be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the supply voltage range. Unused inputs must always be tied to a defined logic voltage level. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 139 10.8 Tape and reel specification 10.8.1 Tape and reel dimensions The following picture describes the dimensions of the tape used for shipping the BMC150 sensor device. The material of the tape is made of conductive polystyrene (IV). Figure 39: Tape and reel dimensions in mm 10.8.2 Orientation within the reel Processing direction Figure 40: Orientation of the BMC150 devices relative to the tape BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 140 10.9 Environmental safety The BMC150 sensor meets the requirements of the EC restriction of hazardous substances (RoHS) directive, see also: Directive 2002/95/EC of the European Parliament and of the Council of 8 September 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 10.9.1 Halogen content The BMC150 is halogen-free. For more details on the analysis results please contact your Bosch Sensortec representative. 10.9.2 Internal package structure Within the scope of Bosch Sensortec's ambition to improve its products and secure the mass product supply, Bosch Sensortec qualifies additional sources (e.g. 2nd source) for the LGA package of the BMC150. While Bosch Sensortec took care that all of the technical packages parameters are described above are 100% identical for all sources, there can be differences in the chemical content and the internal structural between the different package sources. However, as secured by the extensive product qualification process of Bosch Sensortec, this has no impact to the usage or to the quality of the BMC150 product. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 141 11. Legal disclaimer 11.1 Engineering samples Engineering Samples are marked with an asterisk (*) or (e) or (E). Samples may vary from the valid technical specifications of the product series contained in this data sheet. They are therefore not intended or fit for resale to third parties or for use in end products. Their sole purpose is internal client testing. The testing of an engineering sample may in no way replace the testing of a product series. Bosch Sensortec assumes no liability for the use of engineering samples. The Purchaser shall indemnify Bosch Sensortec from all claims arising from the use of engineering samples. 11.2 Product use Bosch Sensortec products are developed for the consumer goods industry. They may only be used within the parameters of this product data sheet. They are not fit for use in life-sustaining or security sensitive systems. Security sensitive systems are those for which a malfunction is expected to lead to bodily harm or significant property damage. In addition, they are not fit for use in products which interact with motor vehicle systems. The resale and/or use of products are at the purchaser's own risk and his own responsibility. The examination of fitness for the intended use is the sole responsibility of the Purchaser. The purchaser shall indemnify Bosch Sensortec from all third party claims arising from any product use not covered by the parameters of this product data sheet or not approved by Bosch Sensortec and reimburse Bosch Sensortec for all costs in connection with such claims. The purchaser must monitor the market for the purchased products, particularly with regard to product safety, and inform Bosch Sensortec without delay of all security relevant incidents. 11.3 Application examples and hints With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Bosch Sensortec hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of noninfringement of intellectual property rights or copyrights of any third party. The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. They are provided for illustrative purposes only and no evaluation regarding infringement of intellectual property rights or copyrights or regarding functionality, performance or error has been made. BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Datasheet eCompass BMC150 Page 142 12. Document history and modification Rev. No Chapter 0.1 9.1 0.2 0.3 0.4 1.0 1.3 10.1 10.5 10.8.1 1.2 1.3 8.2 8 10 6.2 1.2 1.3 2 4.2.1 4.3.1, 6.5 4.5.1 4.5.2 4.7.3 4.7.6 4.7.7 4.7.8, 6.11 4.7.10 6.7 6.9 6.11 6.12 6.15 8.1 8.2 10.1 10.9 Description of modification/changes Date Document creation Page 1: Technical reference code corrected Table 52: Pin description, corresponding sensor of CSB changed from Acc to Mag+Acc, PS from Mag to Mag+Acc (both pins are shared by accelerometer and magnetometer) Table 56: "1300T exchanged by "1300T" Figure 41: Contains position and dimensions of Pin1 marking device marking updated Tape and reel specification added Table 2: dTS and OTS updated Table 3: Brg,z updated Table 51: IC timings updated Table 47 updated number of pins corrected Figure 18: Chip ID update Final status Updated current consumption in power mode Footnote heading accuracy edited ESD MM specification added (was already available in Qualification Report) Power mode description update Center temperature update -> 23C Description of slow compensation updated "Fast compensation" description improved Electrical behavior updated Description of tab interrupt updated Typo corrected, orient_hyst ->(0x2c) Description of flat detection updated, (0x2F) Description of high-g interrupt updated Description g-range selection updated PMU_LOW_NOISE renamed PMU_LOW_POWER 0x2B:tap_th<3:0> ->tap_tap_th<4:0>, 0x2F: flat_hy, 0x37: cut_off updated Typo in self test waiting time -> 50 ms 0x38, 0x39, 0x3A offset_target_x/y/z -> offset_x/y/z SPI timings updated, VDDIO<1.62 V 7.5 MHz limit of SPI frequency IC description update, Figure 24: Update Update package outline dimensions Sensor fulfills newest EC restrictions (RoHS) 2012-07-30 2012-11-06 2012-12-06 2013-02-05 2014-07-14 Bosch Sensortec GmbH Gerhard-Kindler-Strasse 8 72770 Reutlingen / Germany contact@bosch-sensortec.com www.bosch-sensortec.com Modifications reserved | Printed in Germany Specifications subject to change without notice Document number: BST-BMC150-DS000-04 Version_1.0_072014 BST-BMC150-DS000-04 | Revision 1.0 | July 2014 Bosch Sensortec (c) Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. Not intended for publication. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bosch Sensortec: BMC150 0330.SB0.156