SCOPE: CMOS VOLTAGE CONVERTER Device Type 01 Generic Number MAX1044(x)/883B SMD Number 5962-3870701 Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter Maxim SMD JA P TV G Mil-Std-1835 Case Outline GDIP1-T08 or CDIP2-T08 MACY1-8X 8 LEAD CERDIP 8 LEAD CAN Package Code J08 8 TO 99 Absolute Maximum Ratings Voltage Referenced to VVDD TO GND .................................................................................................................... 9.5V Input Voltage (Boost, LV and OSC)1/ ..................................... (-0.3Vdc)VIN V+ +0.3Vdc) Output short circuit duration (V+5.5V dc) .......................................................... Continuous Current into LV pin .......................................................................................................... 20A Lead Temperature (soldering, 10 seconds) ........................................................................ +300C Storage Temperature ........................................................................................... -65C to +150C Continuous Power Dissipation ................................................................................... TA=+70C 8 lead CERDIP(derate 8.0mW/C above +70C) ......................................................... 640mW 8 lead Can(derate 6.67mW/C above +70C) ................................................................ 533mW Junction Temperature TJ .............................................................................................. +150C Thermal Resistance, Junction to Case, JC: Case Outline 8 lead CERDIP.......................................................................... 55C/W Case Outline 8 lead Can ................................................................................. 45C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 8 lead CERDIP........................................................................ 125C/W Case Outline 8 lead Can ................................................................................ 150C/W Recommended Operating Conditions Ambient Operating Range (TA) .................................................................... -55C to +125C Supply Voltage Range (V+) ........................................................................ 1.5V dc to 9.0V dc 1/ Connecting any input terminal to voltages greater than V+ or less than ground may cause destructive latchup. It is recommended that no inputs from sources operating from external supplies be applied prior to power-up of the device. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of MAX1044/883B for /883B and SMD 5962-3870701 19-0193 Page 2 of Rev. C 5 TABLE 1. ELECTRICAL TESTS: TEST SWITCH Minimum Supply Voltage Minimum Supply Voltage Maximum Supply Voltage Output Resistance Oscillator Frequency NOTE 2 Power Efficiency Voltage Conversion Efficiency Oscillator Sink Current Oscillator Source Current CONDITIONS -55 C <=TA<= +125C V+=+5.0V Unless otherwise specified Symbol Group A Subgroup Device type Limits Min Limits Max 1 All V+Min RL= Boost and OSC, no connection RL=10k 1,2,3 All V+Max RL=10k 1,2,3 All 9.0 ROUT IL=20mA, fOSC=5.0kHz 1 2,3 All 100 150 fOSC IL=3.0mA, fOSC=1.0kHz, V+=2V COSC=1.0pF, V+=5.0V 1,2,3 4,5,6 PEFF VCEFF COSC=1.0pF, V+=5.0V RL=5k, fOSC=5kHz RL= ISINK ISOURCE ICC 200 1.5 Units A V V 400 All 5.0 4,5,6 1 1 All All All 1.0 95 97 VOSC=V+, BOOST=0V 1,2,3 All 0.1 3.0 VOSC=V+, BOOST=V+ VOSC=0V, BOOST=0V 1,2,3 1,2,3 All All 1.0 0.1 20 3.0 VOSC=0V, BOOST=V+ 1,2,3 All 1.0 20 kHz % % A A NOTE 2: fOSC is tested with COSC=100pF to minimize the effects of test fixture capacitance loading. The 1.0pF frequency is correlated to this 100pF test point and is intended to simulate the capacitance at the OSC pin when the device is plugged into a test socket and no external capacitor is used. Package 8 pin CERDIP 8 pin Can ORDERING INFORMATION: MAX1044MJA/883B MAX1044MTV/883B SMD Number 5962-3870701MPA 5962-3870701MGC TERMINAL CONNECTIONS: 1 2 3 4 5 6 7 8 J8 BOOST CAP+ GND CAPVOUT LV OSC V+ ---------------------------- TO99 BOOST CAP+ GND CAPVOUT LV OSC V+ Electrical Characteristics of MAX1044/883B for /883B and SMD 5962-3870701 19-0193 Page 3 of Rev. C 5 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 1 PDA applies to Subgroup 1 only. ---------------------------- Electrical Characteristics of MAX1044/883B for /883B and SMD 5962-3870701 19-0193 Page 4 of Rev. C 5