K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Document Title 512Kx36 & 1Mx18-Bit Synchronous Burst SRAM Revision History Rev. No. 0.0 History 1. Initial draft Draft Date Feb. 23. 2001 Remark Preliminary 0.1 1. Add JTAG Scan Order May. 10. 2001 Preliminary 0.2 1. Add x32 org and industrial temperature . 2. Add 165FBGA package Aug. 30. 2001 Preliminary 1.0 1. Final spec release May. 10. 2002 Final 1.1 1. Delete 119BGA package. 2. Correct the Ball Size of 165 FBGA. April 04. 2003 Final 2.0 1. Delete x32 Org. 2. Delete 165FBGA package. 3. Delelte the 6.5 ns speed bin. Nov. 17, 2003 Final -1- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM 16Mb SB/SPB Synchronous SRAM Ordering Information Org. Mode VDD Speed SB ; Access Time(ns) SPB ; Cycle Time(MHz) SB 3.3 7.5/8.5ns K7A161800A-QC(I)25/16/14 SPB(2E1D) 3.3 250/167/138MHz K7A161801A-QC(I)20/16 SPB(2E2D) 3.3 200/167MHz K7B163625A-QC(I)75/85 SB 3.3 7.5/8.5ns SPB(2E1D) 3.3 250/167/138MHz SPB(2E2D) 3.3 200/167MHz Part Number K7B161825A-QC(I)75/85 1Mx18 512Kx36 K7A163600A-QC(I)25/16/14 K7A163601A-QC(I)20/16 -2- PKG Temp C ; Commercial Temp.Range Q : 100TQFP I ; Industrial Temp.Range Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM 512Kx36 & 1Mx18-Bit Synchronous Burst SRAM FEATURES GENERAL DESCRIPTION * Synchronous Operation. * On-Chip Address Counter. * Self-Timed Write Cycle. * On-Chip Address and Control Registers. * 3.3V+0.165V/-0.165V Power Supply. * I/O Supply Voltage 3.3V+0.165V/-0.165V for 3.3V I/O or 2.5V+0.4V/-0.125V for 2.5V I/O * 5V Tolerant Inputs Except I/O Pins. * Byte Writable Function. * Global Write Enable Controls a full bus-width write. * Power Down State via ZZ Signal. * LBO Pin allows a choice of either a interleaved burst or a linear burst. * Three Chip Enables for simple depth expansion with No Data Contention only for TQFP. * Asynchronous Output Enable Control. * ADSP , ADSC, ADV Burst Control Pins. * TTL-Level Three-State Output. * 100-TQFP-1420A * Operating in commeical and industrial temperature range. The K7B163625A and K7B161825A are 18,874,368-bit Synchronous Static Random Access Memory designed for high performance second level cache of Pentium and Power PC based System. It is organized as 512K(1M) words of 36(32/18) bits and integrates address and control registers, a 2-bit burst address counter and added some new functions for high performance cache RAM applications; GW, BW, LBO, ZZ. Write cycles are internally self-timed and synchronous. Full bus-width write is done by GW, and each byte write is performed by the combination of W Ex and BW when G W is high. And with CS 1 high, ADSP is blocked to control signals. Burst cycle can be initiated with either the address status processor(ADSP) or address status cache controller(ADSC) inputs. Subsequent burst addresses are generated internally in the systems burst sequence and are controlled by the burst address advance(ADV) input. LBO pin is DC operated and determines burst sequence(linear or interleaved). ZZ pin controls Power Down State and reduces Stand-by current regardless of CLK. The K7B163625A and K7B161825A are fabricated using SAMSUNGs high performance CMOS technology and is available in a 100pin TQFP package. Multiple power and ground pins are utilized to minimize ground bounce. FAST ACCESS TIMES Symbol -75 -85 Unit Cycle Time PARAMETER tCYC 8.5 10 ns Clock Access Time tCD 7.5 8.5 ns Output Enable Access Time tOE 3.5 4.0 ns LOGIC BLOCK DIAGRAM CLK LBO BURST CONTROL LOGIC CONTROL REGISTER ADV ADSC A0~A18 or A0~A19 A0~A1 ADDRESS REGISTER A2~A18 or A2~A19 DATA-IN REGISTER CONTROL REGISTER GW BW WEx (x=a,b,c,d or a,b) 512Kx36, 1Mx18 MEMORY ARRAY A0~A1 ADSP CS1 CS2 CS2 BURST ADDRESS COUNTER OUTPUT BUFFER CONTROL LOGIC OE ZZ DQa0 ~ DQd 7 or DQa0 ~ DQb7 DQPa ~ DQPd DQPa,DQPb -3- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM A6 A7 CS 1 CS 2 W Ed W Ec W Eb W Ea CS 2 V DD V SS CLK GW BW OE A DSC A DSP A DV A8 A9 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 Pin TQFP (20mm x 14mm) 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A4 A3 A2 A1 A0 N.C. N.C. V SS V DD A 18 A 17 A 10 A 11 A 12 A 13 A 14 A 15 A 16 K7B163625A(512Kx36) A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LBO NC/DQPc DQc 0 DQc 1 V DDQ V SSQ DQc 2 DQc 3 DQc 4 DQc 5 V SSQ V DDQ DQc 6 DQc 7 N.C. V DD N.C. V SS DQd 0 DQd 1 V DDQ V SSQ DQd 2 DQd 3 DQd 4 DQd 5 V SSQ V DDQ DQd 6 DQd 7 NC/DQPd 100 PIN CONFIGURATION(TOP VIEW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DQPb/NC DQb7 DQb6 V DDQ V SSQ DQb5 DQb4 DQb3 DQb2 V SSQ V DDQ DQb1 DQb0 V SS N.C. V DD ZZ DQa7 DQa6 V DDQ V SSQ DQa5 DQa4 DQa3 DQa2 V SSQ V DDQ DQa1 DQa0 DQPa/NC PIN NAME SYMBOL A 0 - A 18 PIN NAME TQFP PIN NO. Address Inputs 32,33,34,35,36,37,42 43,44,45,46,47,48,49 50,81,82,99,100 ADV Burst Address Advance 83 ADSP Address Status Processor 84 ADSC Address Status Controller 85 CLK Clock 89 CS 1 Chip Select 98 CS 2 Chip Select 97 CS 2 Chip Select 92 WE x(x=a,b,c,d) Byte Write Inputs 93,94,95,96 OE Output Enable 86 GW Global Write Enable 88 BW Byte Write Enable 87 ZZ Power Down Input 64 LBO Burst Mode Control 31 SYMBOL PIN NAME TQFP PIN NO. V DD V SS Power Supply(+3.3V) Ground 15,41,65,91 17,40,67,90 N.C. No Connect 14,16,38,39,66 DQa0~a 7 DQb0~b 7 DQc0 ~c7 DQd0~d 7 DQPa~P d or NC Data Inputs/Outputs 52,53,56,57,58,59,62,63 68,69,72,73,74,75,78,79 2,3,6,7,8,9,12,13 18,19,22,23,24,25,28,29 51,80,1,30 V DDQ Output Power Supply (2.5V or 3.3V) Output Ground 4,11,20,27,54,61,70,77 V SSQ 5,10,21,26,55,60,71,76 Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. -4- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM A6 A7 CS 1 CS 2 N.C. N.C. WEb WEa CS 2 V DD V SS CLK GW BW OE ADS C ADS P ADV A8 A9 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 Pin TQFP (20mm x 14mm) 47 48 49 50 A 14 A 15 A 16 A 17 41 V DD 46 40 V SS A 13 39 N.C. 45 38 N.C. A 12 37 A0 44 36 A1 A 11 35 A2 43 34 A3 A 18 33 A4 42 32 A 19 31 K7B161825A(1Mx18) A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LBO N.C. N.C. N.C. V DDQ V SSQ N.C. N.C. DQb0 DQb1 V SSQ V DDQ DQb2 DQb3 N.C. V DD N.C. V SS DQb4 DQb5 V DDQ V SSQ DQb6 DQb7 DQPb N.C. V SSQ V DDQ N.C. N.C. N.C. 100 PIN CONFIGURATION(TOP VIEW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A 10 N.C. N.C. V DDQ V SSQ N.C. DQPa DQa7 DQa6 V SSQ V DDQ DQa5 DQa4 V SS N.C. V DD ZZ DQa3 DQa2 V DDQ V SSQ DQa1 DQa0 N.C. N.C. V SSQ V DDQ N.C. N.C. N.C. PIN NAME SYMBOL PIN NAME A 0 - A 19 Address Inputs ADV ADSP ADSC CLK CS 1 CS 2 CS 2 W Ex(x=a,b) OE GW BW ZZ LBO Burst Address Advance Address Status Processor Address Status Controller Clock Chip Select Chip Select Chip Select Byte Write Inputs Output Enable Global Write Enable Byte Write Enable Power Down Input Burst Mode Control TQFP PIN NO. SYMBOL 32,33,34,35,36,37,42 43,44,45,46,47,48,49 50 80,81,82,99,100 83 84 85 89 98 97 92 93,94 86 88 87 64 31 PIN NAME TQFP PIN NO. V DD V SS N.C. Power Supply(+3.3V) Ground No Connect 15,41,65,91 17,40,67,90 1,2,3,6,7,14,16,25,28,29, 30,38,39,51,52,53,56,57, 66,75,78,79,95,96 DQa 0 ~ a7 DQb 0 ~ b7 DQPa, Pb Data Inputs/Outputs 58,59,62,63,68,69,72,73 8,9,12,13,18,19,22,23 74,24 V DDQ Output Power Supply (2.5V or 3.3V) Output Ground 4,11,20,27,54,61,70,77 V SSQ 5,10,21,26,55,60,71,76 Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. -5- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM FUNCTION DESCRIPTION The K7B163625A and K7B161825A are synchronous SRAM designed to support the burst address accessing sequence of the Power PC based microprocessor. All inputs (with the exception of OE, LBO and ZZ) are sampled on rising clock edges. The start and duration of the burst access is controlled by ADSC, ADSP and ADV and chip select pins. The accesses are enabled with the chip select signals and output enabled signals. Wait states are inserted into the access with ADV. When ZZ is pulled high, the SRAM will enter a Power Down State. At this time, internal state of the SRAM is preserved. When ZZ returns to low, the SRAM normally operates after 2cycles of wake up time. ZZ pin is pulled down internally. Read cycles are initiated with ADSP(or ADSC) using the new external address clocked into the on-chip address register when both G W and BW are high or when BW is low and WEa, WEb, WEc, and WE d are high. When ADSP is sampled low, the chip selects are sampled active, and the output buffer is enabled with O E. the data of cell array accessed by the current address are projected to the output pins. Write cycles are also initiated with ADSP(or ADSC) and are differentiated into two kinds of operations; All byte write operation and individual byte write operation. All byte write occurs by enabling G W(independent of BW and WEx.), and individual byte write is performed only when GW is high and BW is low. In K7B163625M, a 512Kx36 organization, W Ea controls DQa0 ~ DQa7 and DQPa, WEb controls DQb0 ~ DQb7 and DQPb, WEc controls DQc0 ~ DQc7 and DQPc and WEd controls DQd0 ~ DQd7 and DQPd. CS1 is used to enable the device and conditions internal use of ADSP and is sampled only when a new external address is loaded. ADV is ignored at the clock edge when ADSP is asserted, but can be sampled on the subsequent clock edges. The address increases internally for the next access of the burst when ADV is sampled low. Addresses are generated for the burst access as shown below, The starting point of the burst sequence is provided by the external address. The burst address counter wraps around to its initial state upon completion. The burst sequence is determined by the state of the LBO pin. When this pin is Low, linear burst sequence is selected. And this pin is High, Interleaved burst sequence is selected. BURST SEQUENCE TABLE LBO PIN HIGH First Address Fourth Address (Interleaved Burst) Case 1 A1 0 0 1 1 Case 2 A0 0 1 0 1 A1 0 0 1 1 Case 3 A0 1 0 1 0 A1 1 1 0 0 Case 4 A0 0 1 0 1 A1 1 1 0 0 BQ TABLE LBO PIN A0 1 0 1 0 (Linear Burst) LOW First Address Fourth Address Case 1 A1 0 0 1 1 Case 2 A0 0 1 0 1 A1 0 1 1 0 Case 3 A0 1 0 1 0 A1 1 1 0 0 Case 4 A0 0 1 0 1 A1 1 0 0 1 A0 1 0 1 0 Note : 1. LBO pin must be tied to High or Low, and Floating State must not be allowed . -6- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM TRUTH TABLES SYNCHRONOUS TRUTH TABLE CS 1 CS2 CS 2 ADV WRITE CLK ADDRESS ACCESSED OPERATION H X X ADSP ADSC X L X X N/A Not Selected L L X L X X X N/A Not Selected L X H L X X X N/A Not Selected L L X X L X X N/A Not Selected L X H X L X X N/A Not Selected L H L L X X X External Address Begin Burst Read Cycle L H L H L X L External Address Begin Burst Write Cycle L H L H L X H External Address Begin Burst Read Cycle X X X H H L H Next Address Continue Burst Read Cycle H X X X H L H Next Address Continue Burst Read Cycle X X X H H L L Next Address Continue Burst Write Cycle H X X X H L L Next Address Continue Burst Write Cycle X X X H H H H Current Address Suspend Burst Read Cycle H X X X H H H Current Address Suspend Burst Read Cycle X X X H H H L Current Address Suspend Burst Write Cycle H X X X H H L Current Address Suspend Burst Write Cycle Notes : 1. X means "Don t Care". 2. The rising edge of clock is symbolized by . 3. WRITE = L means Write operation in WRITE TRUTH TABLE. WRITE = H means Read operation in WRITE TRUTH TABLE. 4. Operation finally depends on status of asynchronous input pins(ZZ and OE ). WRITE TRUTH TABLE( x36) GW BW WEa WEb WEc WE d OPERATION H H X X X X READ H L H H H H READ H L L H H H WRITE BYTE a H L H L H H WRITE BYTE b H L H H L L WRITE BYTE c and d H L L L L L WRITE ALL BYTEs L X X X X X WRITE ALL BYTEs Notes : 1. X means "Dont Care". 2. All inputs in this table must meet setup and hold time around the rising edge of CLK(). WRITE TRUTH TABLE(x18) GW BW WEa WEb OPERATION H H X X READ H L H H READ H L L H WRITE BYTE a H L H L WRITE BYTE b H L L L WRITE ALL BYTEs L X X X WRITE ALL BYTEs Notes : 1. X means "Dont Care". 2. All inputs in this table must meet setup and hold time around the rising edge of CLK(). -7- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM ASYNCHRONOUS TRUTH TABLE Operation ZZ OE I/O STATUS Sleep Mode H X High-Z L L DQ L H High-Z Write L X Din, High-Z Deselected L X High-Z Read Notes 1. X means "Dont Care". 2. ZZ pin is pulled down internally 3. For write cycles that following read cycles, the output buffers must be disabled with OE, otherwise data bus contention will occur. 4. Sleep Mode means power down state of which stand-by current does not depend on cycle time. 5. Deselected means power down state of which stand-by current depends on cycle time. ABSOLUTE MAXIMUM RATINGS* PARAMETER SYMBOL RATING UNIT Voltage on V DD Supply Relative to V SS V DD -0.3 to 4.6 V Voltage on V DDQ Supply Relative to V SS V DDQ V DD V Voltage on Input Pin Relative to V SS VI N -0.3 to V DD+0.3 V Voltage on I/O Pin Relative to V SS V IO -0.3 to VDDQ+0.3 V Power Dissipation PD 1.6 W TSTG -65 to 150 C Commercial T OPR 0 to 70 C Industrial T OPR -40 to 85 C TBIAS -10 to 85 C Storage Temperature Operating Temperature Storage Temperature Range Under Bias *Note : Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING CONDITIONS at 3.3V I/O(0C TA 70C) PARAMETER Supply Voltage Ground SYMBOL MIN Typ. MAX UNIT V DD 3.135 3.3 3.465 V V DDQ 3.135 3.3 3.465 V V SS 0 0 0 V * The above parameters are also guaranteed at industrial temperature range. OPERATING CONDITIONS at 2.5V I/O(0C TA 70C) PARAMETER Supply Voltage Ground SYMBOL MIN Typ. MAX UNIT V DD 3.135 3.3 3.465 V V DDQ 2.375 2.5 2.9 V V SS 0 0 0 V * The above parameters are also guaranteed at industrial temperature range. CAPACITANCE* (TA=25C, f=1MHz) PARAMETER Input Capacitance Output Capacitance SYMBOL TEST CONDITION MIN MAX UNIT C IN V IN=0V - 5 pF C OUT V OUT =0V - 7 pF *Note : Sampled not 100% tested. -8- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM DC ELECTRICAL CHARACTERISTICS (VDD =3.3V+0.165V/-0.165V, TA =0C to +70C) Parameter Symbol Input Leakage Current(except ZZ) IIL V DD=Max ; VIN=VSS to V DD Output Leakage Current IOL Output Disabled, Vout=V SS to V DDQ Operating Current ICC ISB Test Conditions Min Max Unit -2 +2 A A -2 +2 Device Selected, I OUT=0mA, -75 - 250 ZZ V IL , Cycle Time tCYC Min -85 - 230 Device deselected, I OUT=0mA, -75 - 90 -85 - 80 - 70 mA - 60 mA 0.4 V ZZ V IL, f=Max, All Inputs 0.2V or V DD-0.2V mA Notes 1,2 mA Device deselected, I OUT=0mA, Standby Current ISB1 ZZ 0.2V, f=0, All Inputs=fixed (VDD-0.2V or Device deselected, I OUT=0mA, ISB2 ZZV DD-0.2V, f=Max, All Inputs V IL or V I H Output Low Voltage(3.3V I/O) V OL IOL =8.0mA - Output High Voltage(3.3V I/O) V OH IOH=-4.0mA 2.4 - V Output Low Voltage(2.5V I/O) V OL IOL =1.0mA - 0.4 V Output High Voltage(2.5V I/O) V OH IOH=-1.0mA Input Low Voltage(3.3V I/O) V IL Input High Voltage(3.3V I/O) Input Low Voltage(2.5V I/O) Input High Voltage(2.5V I/O) 2.0 - V -0.3* 0.8 V V IH 2.0 V DD+0.3** V V IL -0.3* 0.7 V V IH 1.7 V DD+0.3** V 3 3 Notes : 1. The above parameters are also guaranteed at industrial temperature range. 2. Reference AC Operating Conditions and Characteristics for input and timing. 3. Data states are all zero. 4. In Case of I/O Pins, the Max. VIH =V DDQ +0.3V VIH VSS VSS- 1.0V 20% tCYC (MIN) TEST CONDITIONS (V DD=3.3V+0.165V/-0.165V,VDDQ =3.3V+0.165/-0.165V or VDD=3.3V+0.165V/-0.165V,VDDQ =2.5V+0.4V/-0.125V, TA=0to70C) PARAMETER VALUE Input Pulse Level(for 3.3V I/O) 0 to 3.0V Input Pulse Level(for 2.5V I/O) 0 to 2.5V Input Rise and Fall Time(Measured at 20% to 80% for 3.3V I/O) 1.0V/ns Input Rise and Fall Time(Measured at 20% to 80% for 2.5V I/O) 1.0V/ns Input and Output Timing Reference Levels for 3.3V I/O 1.5V Input and Output Timing Reference Levels for 2.5V I/O V DDQ/2 Output Load See Fig. 1 * The above parameters are also guaranteed at industrial temperature range. -9- Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Output Load(A) Output Load(B), (for tLZC, tLZOE, tHZOE & tHZC) +3.3V for 3.3V I/O /+2.5V for 2.5V I/O RL=50 Dout Zo=50 30pF* VL=1.5V for 3.3V I/O V DDQ/2 for 2.5V I/O 319 / 1667 Dout 353 / 1538 5pF* * Including Scope and Jig Capacitance Fig. 1 AC TIMING CHARACTERISTICS (VDD =3.3V+0.165V/-0.165V, TA=0C to +70C) -75 PARAMETER SYMBOL -85 MIN MAX MIN MAX UNIT Cycle Time tCYC 8.5 - 10 - ns Clock Access Time tCD - 7.5 - 8.5 ns Output Enable to Data Valid tOE - 3.5 - 4.0 ns Clock High to Output Low-Z tLZC 2.5 - 2.5 - ns Output Hold from Clock High tOH 2.5 - 2.5 - ns Output Enable Low to Output Low-Z tLZOE 0 - 0 - ns Output Enable High to Output High-Z tHZOE - 3.5 - 4.0 ns Clock High to Output High-Z tHZC - 4.0 - 5.0 ns Clock High Pulse Width tCH 2.5 - 3.0 - ns Clock Low Pulse Width tCL 2.5 - 3.0 - ns Address Setup to Clock High tAS 2.0 - 2.0 - ns Address Status Setup to Clock High tSS 2.0 - 2.0 - ns Data Setup to Clock High tDS 2.0 - 2.0 - ns Write Setup to Clock High (GW , BW , WE X) tWS 2.0 - 2.0 - ns Address Advance Setup to Clock High tADVS 2.0 - 2.0 - ns Chip Select Setup to Clock High tCSS 2.0 - 2.0 - ns Address Hold from Clock High tAH 0.5 - 0.5 - ns Address Status Hold from Clock High tSH 0.5 - 0.5 - ns Data Hold from Clock High tDH 0.5 - 0.5 - ns Write Hold from Clock High (G W, BW, WE X ) tWH 0.5 - 0.5 - ns Address Advance Hold from Clock High tADVH 0.5 - 0.5 - ns Chip Select Hold from Clock High tCSH 0.5 - 0.5 - ns ZZ High to Power Down tPDS 2 - 2 - cycle ZZ Low to Power Up tPUS 2 - 2 - cycle Notes : 1. The above parameters are also guaranteed at industrial temperature range. 2. All address inputs must meet the specified setup and hold times for all rising clock edges whenever ADSC and/or ADSP is sampled low and CS is sampled low. All other synchronous inputs must meet the specified setup and hold times whenever this device is chip selected. 3. Both chip selects must be active whenever ADSC or ADSP is sampled low in order for the this device to remain enabled. 4. ADSC or ADSP must not be asserted for at least 2 Clock after leaving ZZ state. - 10 - Nov. 2003 Rev 2.0 - 11 - Data Out OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK tCSS tAS tSS tOE Q1-1 tHZOE tADVH tWH tSS A2 tSH Q2-1 tCD tOH Q2-2 CS = L means CS1 = L, CS2 = H and CS 2 = L CS = H mean s CS1 = H, or CS1 = L and CS2 = H, or CS1 = L , and CS2 = L Q 2-3 A3 Q2-4 (ADV INSERTS WAIT STATE) BURST CONTINUED WITH NEW BASE ADDRESS tCYC tCL NOTES : WRITE = L mea ns GW = L, or GW = H, B W = L, WEx.= L tADVS tCSH tWS tLZOE A1 tAH tSH tCH TIMING WAVEFORM OF READ CYCLE Q3-1 Q 3-2 Q3-3 Undefined Dont Care Q3-4 tHZC K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 - 12 - Data Out Data In OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK Q0-3 tCSS tAS tSS Q 0-4 A1 tLZOE tCSH tAH tSH D1-1 tCH tCYC tCL A2 D2-1 D2-2 (ADV SUSPENDS BURST) D2-2 D2-3 (ADSC EXTENDED BURST) TIMING WAVEFORM OF WRTE CYCLE D2-4 D3-1 A3 tDS tADVS tWS tSS D3-2 tDH tADVH tWH tSH D3-3 Unde fine d Dont Care D3-4 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 - 13 - Data Out Data In OE ADV CS WRITE ADDRESS ADSP CLOCK tHZC tSS A1 tLZC tCD tSH Q1-1 tHZOE tAS A2 tCL tCYC tDS tADVS tWS tAH tCH D2-1 tDH tADVH tWH A3 tLZOE tOE Q3-1 Q 3-2 Q3-3 tOH Q3-4 TIMING WAVEFORM OF COMBINATION READ/WRTE CYCLE(ADSP CONTROLLED, ADSC=HIGH) Unde fine d Dont Care K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 - 14 - Data In Data Out OE ADV CS WRITE ADDRESS ADSC CLOCK tCSS tSS A1 tLZOE tOE tCSH tSH Q1-1 A2 Q 2-1 A3 Q3-1 A4 Q4-1 tHZOE D5-1 A5 tDS tWS D6-1 A6 tDH tWH D7-1 A7 tWS tCD A8 A9 Q8-1 tCL tCYC tWH tCH TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSC CONTROLLED, ADSP=HIGH) Unde fine d Dont Care Q9-1 tOH K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 - 15 - Data In Data Out OE ADV CS WRITE ADDRESS ADSP CLOCK tCSS tSS t OE tCSH tL ZOE A1 tSH Q1-1 A2 Q2-1 A3 tAS Q 3-1 A4 tAH tCYC tCH Q4-1 A5 tCL tHZOE D5-1 A6 tDS D6-1 tDH A7 D7-1 tCD A8 Q8-1 A9 TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSP CONTROLLED, ADSC=HIGH) Q9-1 tOH Unde fine d Dont Care K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 - 16 - ZZ Data Out Data In OE ADV CS WRITE ADDRESS ADSC ADSP CLOCK tCSS tAS tSS A1 tLZOE tOE tCSH tAH tSH Q1-1 ZZ Setup Cycle tPDS tHZC Sleep State ZZ Recovery Cycle tPUS tCL tCYC tCH TIMING WAVEFORM OF POWER DOWN CYCLE tWS Normal Operation Mode tHZOE A2 D2-1 tWH Unde fine d Dont Care D2-2 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM APPLICATION INFORMATION DEPTH EXPANSION The Samsung 512Kx36 Synchronous Burst SRAM has two additional chip selects for simple depth expansion. This permits easy secondary cache upgrades from 512K depth to 1M depth without extra logic. I/O[0:71] Data Address A[0:19] A[19] A[0:18] A[19] A[0:18] Address Data CLK CS2 CS2 CS2 CLK Microprocessor Address ADSC CLK Address Data CS2 512Kx36 SB SRAM CLK ADSC WEx OE Cache Controller WEx (Bank 0) (Bank 1) OE CS1 CS1 ADV 512Kx36 SB SRAM ADSP ADV ADSP ADS INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing) (ADSP CONTROLLED , ADSC=HIGH) CLOCK tSS tSH ADSP tAS ADDRESS [0:n] tAH A1 A2 tWS tWH WRITE tCSS tCSH CS1 Bank 0 is selected by CS 2, and Bank 1 deselected by CS2 An+1 tADVS Bank 0 is deselected by CS2, and Bank 1 selected by CS2 tADVH ADV OE tOE Data Out (Bank 0) Data Out (Bank 1) tLZOE tHZC Q1-1 Q1-2 Q1-3 Q1-4 tCD tLZC Q2-1 *Notes : n = 14 32K depth , 16 128K depth , 18 512K depth , 15 64K depth 17 256K depth 19 1M depth Q2-2 Q2-3 Q2-4 Dont Care - 17 - Undefined Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM APPLICATION INFORMATION DEPTH EXPANSION The Samsung 1Mx18 Synchronous Burst SRAM has two additional chip selects for simple depth expansion. This permits easy secondary cache upgrades from 1M depth to 2M depth without extra logic. I/O[0:71] Data Address A[20] A[0:20] A[20] A[0:19] Address Data CLK Address Data CS2 CS2 CS2 Microprocessor CLK Address ADSC CLK CS2 1Mx18 SB SRAM CLK ADSC WEx OE OE CS1 ADV 1Mx18 SB SRAM WEx (Bank 0) Cache Controller A[0:19] (Bank 1) CS1 ADSP ADV ADSP ADS INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing) (ADSP CONTROLLED , ADSC=HIGH) CLOCK tSS tSH ADSP tAS ADDRESS [0:n] tAH A1 A2 tWS tWH WRITE tCSS tCSH CS1 Bank 0 is selected by CS 2, and Bank 1 deselected by CS2 An+1 tADVS Bank 0 is deselected by CS2, and Bank 1 selected by CS2 tADVH ADV OE tOE Data Out (Bank 0) Data Out (Bank 1) tLZOE tHZC Q1-1 Q1-2 Q1-3 Q1-4 tCD tLZC Q2-1 *Notes : n = 14 16 18 20 32K depth , 128K depth , 512K depth , 2M depth 15 64K depth 17 256K depth 19 1M depth Q2-2 Q2-3 Q2-4 Dont Care - 18 - Undefined Nov. 2003 Rev 2.0 K7B163625A K7B161825A 512Kx36 & 1Mx18 Synchronous SRAM PACKAGE DIMENSIONS 100-TQFP-1420A Units ; millimeters/Inches 22.00 0.30 20.00 0.20 0~8 0.10 0.127 +- 0.05 16.00 0.30 14.00 0.20 0.10 MAX (0.83) 0.50 #1 0.65 0.10 (0.58) 0.30 0.10 0.10 MAX 1.40 0.50 0.10 - 19 - 0.10 1.60 MAX 0.05 MIN Nov. 2003 Rev 2.0