74LVC1T45; 74LVCH1T45 Dual supply translating transceiver; 3-state Rev. 6 -- 6 August 2012 Product data sheet 1. General description The 74LVC1T45; 74LVCH1T45 are single bit, dual supply transceivers with 3-state outputs that enable bidirectional level translation. They feature two 1-bit input-output ports (A and B), a direction control input (DIR) and dual supply pins (VCC(A) and VCC(B)). Both VCC(A) and VCC(B) can be supplied at any voltage between 1.2 V and 5.5 V making the device suitable for translating between any of the low voltage nodes (1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V and 5.0 V). Pins A and DIR are referenced to VCC(A) and pin B is referenced to VCC(B). A HIGH on DIR allows transmission from A to B and a LOW on DIR allows transmission from B to A. The devices are fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing any damaging backflow current through the device when it is powered down. In suspend mode when either VCC(A) or VCC(B) are at GND level, both A port and B port are in the high-impedance OFF-state. Active bus hold circuitry in the 74LVCH1T45 holds unused or floating data inputs at a valid logic level. 2. Features and benefits Wide supply voltage range: VCC(A): 1.2 V to 5.5 V VCC(B): 1.2 V to 5.5 V High noise immunity Complies with JEDEC standards: JESD8-7 (1.2 V to 1.95 V) JESD8-5 (1.8 V to 2.7 V) JESD8C (2.7 V to 3.6 V) JESD36 (4.5 V to 5.5 V) ESD protection: HBM JESD22-A114F Class 3A exceeds 4000 V CDM JESD22-C101E exceeds 1000 V Maximum data rates: 420 Mbps (3.3 V to 5.0 V translation) 210 Mbps (translate to 3.3 V)) 140 Mbps (translate to 2.5 V) 75 Mbps (translate to 1.8 V) 60 Mbps (translate to 1.5 V) Suspend mode 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Latch-up performance exceeds 100 mA per JESD 78 Class II 24 mA output drive (VCC = 3.0 V) Inputs accept voltages up to 5.5 V Low power consumption: 16 A maximum ICC IOFF circuitry provides partial Power-down mode operation Multiple package options Specified from 40 C to +85 C and 40 C to +125 C 3. Ordering information Table 1. Ordering information Type number 74LVC1T45GW Package Temperature range Name Description Version 40 C to +125 C SC-88 plastic surface-mounted package; 6 leads SOT363 40 C to +125 C XSON6 plastic extremely thin small outline package; no leads; SOT886 6 terminals; body 1 1.45 0.5 mm 40 C to +125 C XSON6 plastic extremely thin small outline package; no leads; SOT891 6 terminals; body 1 1 0.5 mm 40 C to +125 C XSON6 extremely thin small outline package; no leads; 6 terminals; body 0.9 1.0 0.35 mm SOT1115 40 C to +125 C XSON6 extremely thin small outline package; no leads; 6 terminals; body 1.0 1.0 0.35 mm SOT1202 74LVCH1T45GW 74LVC1T45GM 74LVCH1T45GM 74LVC1T45GF 74LVCH1T45GF 74LVC1T45GN 74LVCH1T45GN 74LVC1T45GS 74LVCH1T45GS 4. Marking Table 2. Marking Type number Marking code[1] 74LVC1T45GW V5 74LVCH1T45GW X5 74LVC1T45GM V5 74LVCH1T45GM X5 74LVC1T45GF V5 74LVCH1T45GF X5 74LVC1T45GN V5 74LVCH1T45GN X5 74LVC1T45GS V5 74LVCH1T45GS X5 [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 2 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 5. Functional diagram DIR 5 DIR A 3 A 4 VCC(A) B B VCC(B) VCC(A) VCC(B) 001aag886 001aag885 Fig 1. Logic symbol Fig 2. Logic diagram 6. Pinning information 6.1 Pinning 74LVC1T45 74LVCH1T45 74LVC1T45 74LVCH1T45 VCC(A) 1 GND 2 A 6 5 3 4 VCC(A) 1 6 VCC(B) GND 2 5 DIR A 3 4 B VCC(B) VCC(A) 1 6 VCC(B) GND 2 5 DIR A 3 4 B DIR B Pin configuration SOT363 (SC-88) 001aaj993 001aaj992 Transparent top view 001aaj991 Fig 3. 74LVC1T45 74LVCH1T45 Fig 4. Pin configuration SOT886 (XSON6) Transparent top view Fig 5. Pin configuration SOT891, SOT1115 and SOT1202 6.2 Pin description Table 3. Pin description Symbol Pin Description VCC(A) 1 supply voltage port A and DIR GND 2 ground (0 V) A 3 data input or output B 4 data input or output DIR 5 direction control VCC(B) 6 supply voltage port B 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 3 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 7. Functional description Table 4. Function table[1] Supply voltage Input Input/output[2] VCC(A), VCC(B) DIR A B 1.2 V to 5.5 V L A=B input 1.2 V to 5.5 V H input B=A GND[3] X Z Z [1] H = HIGH voltage level; L = LOW voltage level; X = don't care; Z = high-impedance OFF-state. [2] The input circuit of the data I/O is always active. [3] When either VCC(A) or VCC(B) is at GND level, the device goes into suspend mode. 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC(A) supply voltage A VCC(B) supply voltage B IIK input clamping current VI input voltage IOK output clamping current output voltage VO Conditions VI < 0 V [1] Min Max Unit 0.5 +6.5 V 0.5 +6.5 V 50 - mA 0.5 +6.5 V mA 50 - [1][2][3] 0.5 VCCO + 0.5 V Suspend or 3-state mode [1] 0.5 +6.5 V [2] - 50 mA - 100 mA VO < 0 V Active mode IO output current VO = 0 V to VCCO ICC supply current ICC(A) or ICC(B) IGND ground current 100 - mA Tstg storage temperature 65 +150 C - 250 mW total power dissipation Ptot [1] Tamb = 40 C to +125 C The minimum input voltage ratings and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] VCCO is the supply voltage associated with the output port. [3] VCCO + 0.5 V should not exceed 6.5 V. [4] [4] For SC-88 package: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 package: above 118 C the value of Ptot derates linearly with 7.8 mW/K. 9. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter Min Max Unit VCC(A) supply voltage A 1.2 5.5 V VCC(B) supply voltage B 1.2 5.5 V VI input voltage 0 5.5 V 74LVC_LVCH1T45 Product data sheet Conditions All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 4 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 6. Recommended operating conditions ...continued Symbol Parameter Conditions VO output voltage Active mode [1] Suspend or 3-state mode Tamb t/V ambient temperature input transition rise and fall rate VCCI = 1.2 V [2] Min Max Unit 0 VCCO V 0 5.5 V 40 +125 C - 20 ns/V VCCI = 1.4 V to 1.95 V - 20 ns/V VCCI = 2.3 V to 2.7 V - 20 ns/V VCCI = 3 V to 3.6 V - 10 ns/V VCCI = 4.5 V to 5.5 V - 5 ns/V [1] VCCO is the supply voltage associated with the output port. [2] VCCI is the supply voltage associated with the input port. 10. Static characteristics Table 7. Typical static characteristics at Tamb = 25 C At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VOH HIGH-level output voltage Conditions LOW-level output voltage Typ Max Unit [1] - 1.09 - V [1] - 0.07 - V - - 1 A VI = VIH or VIL IO = 3 mA; VCCO = 1.2 V VOL Min VI = VIH or VIL IO = 3 mA; VCCO = 1.2 V II input leakage current DIR input; VI = 0 V to 5.5 V; VCCI = 1.2 V to 5.5 V [2] IBHL bus hold LOW current A or B port; VI = 0.42 V; VCCI = 1.2 V [2] - 19 - A A or B port; VI = 0.78 V; VCCI = 1.2 V [2] - 19 - A - 19 - A IBHH bus hold HIGH current IBHLO bus hold LOW overdrive current A or B port; VCCI = 1.2 V [2][3] IBHHO bus hold HIGH overdrive current A or B port; VCCI = 1.2 V [2][3] - 19 - A IOZ OFF-state output current A or B port; VO = 0 V or VCCO; VCCO = 1.2 V to 5.5 V [1] - - 1 A IOFF power-off leakage current A port; VI or VO = 0 V to 5.5 V; VCC(A) = 0 V; VCC(B) = 1.2 V to 5.5 V - - 1 A B port; VI or VO = 0 V to 5.5 V; VCC(B) = 0 V; VCC(A) = 1.2 V to 5.5 V - - 1 A CI input capacitance DIR input; VI = 0 V or 3.3 V; VCC(A) = VCC(B) = 3.3 V - 2.2 - pF CI/O input/output capacitance A and B port; suspend mode; VO = 3.3 V or 0 V; VCC(A) = VCC(B) = 3.3 V - 6.0 - pF [1] VCCO is the supply voltage associated with the output port. [2] VCCI is the supply voltage associated with the data input port. [3] To guarantee the node switches, an external driver must source/sink at least IBHLO/IBHHO when the input is in the range VIL to VIH. 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 5 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 8. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VIH HIGH-level input voltage 40 C to +85 C Conditions 40 C to +125 C Unit Min Max Min Max VCCI = 1.2 V 0.8VCCI - 0.8VCCI - V VCCI = 1.4 V to 1.95 V 0.65VCCI - 0.65VCCI - V [1] data input VCCI = 2.3 V to 2.7 V 1.7 - 1.7 - V VCCI = 3.0 V to 3.6 V 2.0 - 2.0 - V VCCI = 4.5 V to 5.5 V 0.7VCCI - 0.7VCCI - V VCCI = 1.2 V 0.8VCC(A) - 0.8VCC(A) - V VCCI = 1.4 V to 1.95 V 0.65VCC(A) - 0.65VCC(A) - V VCCI = 2.3 V to 2.7 V 1.7 - 1.7 - V VCCI = 3.0 V to 3.6 V 2.0 - 2.0 - V 0.7VCC(A) - 0.7VCC(A) - V VCCI = 1.2 V - 0.2VCCI - 0.2VCCI V VCCI = 1.4 V to 1.95 V - 0.35VCCI - 0.35VCCI V DIR input VCCI = 4.5 V to 5.5 V VIL LOW-level input voltage [1] data input VCCI = 2.3 V to 2.7 V - 0.7 - 0.7 V VCCI = 3.0 V to 3.6 V - 0.8 - 0.8 V VCCI = 4.5 V to 5.5 V - 0.3VCCI - 0.3VCCI V DIR input VOH HIGH-level output voltage 74LVC_LVCH1T45 Product data sheet VCCI = 1.2 V - 0.2VCC(A) - 0.2VCC(A) V VCCI = 1.4 V to 1.95 V - 0.35VCC(A) - 0.35VCC(A) V VCCI = 2.3 V to 2.7 V - 0.7 - 0.7 V VCCI = 3.0 V to 3.6 V - 0.8 - 0.8 V VCCI = 4.5 V to 5.5 V - 0.3VCC(A) - VCCO 0.1 - VCCO 0.1 0.3VCC(A) V VI = VIH IO = 100 A; VCCO = 1.2 V to 4.5 V [2] - V IO = 6 mA; VCCO = 1.4 V 1.0 - 1.0 - V IO = 8 mA; VCCO = 1.65 V 1.2 - 1.2 - V IO = 12 mA; VCCO = 2.3 V 1.9 - 1.9 - V IO = 24 mA; VCCO = 3.0 V 2.4 - 2.4 - V IO = 32 mA; VCCO = 4.5 V 3.8 - 3.8 - V All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 6 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 8. Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VOL LOW-level output voltage 40 C to +85 C Conditions Min Max Min Max IO = 100 A; VCCO = 1.2 V to 4.5 V - 0.1 - 0.1 V IO = 6 mA; VCCO = 1.4 V - 0.3 - 0.3 V IO = 8 mA; VCCO = 1.65 V - 0.45 - 0.45 V VI = VIL IO = 12 mA; VCCO = 2.3 V - 0.3 - 0.3 V IO = 24 mA; VCCO = 3.0 V - 0.55 - 0.55 V IO = 32 mA; VCCO = 4.5 V - 0.55 - 0.55 V - 2 - 10 A 15 - 10 - A 25 - 20 - A input leakage current IBHL bus hold LOW A or B port current VI = 0.49 V; VCCI = 1.4 V DIR input; VI = 0 V to 5.5 V; VCCI = 1.2 V to 5.5 V [1] VI = 0.58 V; VCCI = 1.65 V VI = 0.70 V; VCCI = 2.3 V 45 - 45 - A VI = 0.80 V; VCCI = 3.0 V 100 - 80 - A 100 - 100 - A VI = 1.35 V; VCCI = 4.5 V bus hold HIGH A or B port current VI = 0.91 V; VCCI = 1.4 V [1] 15 - 10 - A VI = 1.07 V; VCCI = 1.65 V 25 - 20 - A VI = 1.60 V; VCCI = 2.3 V 45 - 45 - A VI = 2.00 V; VCCI = 3.0 V 100 - 80 - A 100 - 100 - A 125 - 125 - A 200 - 200 - A VCCI = 2.7 V 300 - 300 - A VCCI = 3.6 V 500 - 500 - A 900 - 900 - A 125 - 125 - A 200 - 200 - A VCCI = 2.7 V 300 - 300 - A VCCI = 3.6 V 500 - 500 - A 900 - 900 - A - 2 - 10 A VI = 3.15 V; VCCI = 4.5 V IBHLO [1][3] bus hold LOW A or B port overdrive VCCI = 1.6 V current VCCI = 1.95 V VCCI = 5.5 V IBHHO [1][3] bus hold HIGH A or B port overdrive VCCI = 1.6 V current VCCI = 1.95 V VCCI = 5.5 V IOZ OFF-state output current 74LVC_LVCH1T45 Product data sheet Unit [2] II IBHH 40 C to +125 C A or B port; VO = 0 V or VCCO; VCCO = 1.2 V to 5.5 V [2] All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 7 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 8. Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter IOFF power-off leakage current ICC supply current 40 C to +85 C Conditions 40 C to +125 C Unit Min Max Min Max A port; VI or VO = 0 V to 5.5 V; VCC(A) = 0 V; VCC(B) = 1.2 V to 5.5 V - 2 - 10 A B port; VI or VO = 0 V to 5.5 V; VCC(B) = 0 V; VCC(A) = 1.2 V to 5.5 V - 2 - 10 A VCC(A), VCC(B) = 1.2 V to 5.5 V - 8 - 8 A VCC(A), VCC(B) = 1.65 V to 5.5 V - 3 - 3 A VCC(A) = 5.5 V; VCC(B) = 0 V - 2 - 2 A VCC(A) = 0 V; VCC(B) = 5.5 V 2 - 2 - A VCC(A), VCC(B) = 1.2 V to 5.5 V - 8 - 8 A VCC(A), VCC(B) = 1.65 V to 5.5 V - 3 - 3 A VCC(B) = 5.5 V; VCC(A) = 0 V - 2 - 2 A VCC(B) = 0 V; VCC(A) = 5.5 V 2 - 2 - A VCC(A), VCC(B) = 1.2 V to 5.5 V - 16 - 16 A VCC(A), VCC(B) = 1.65 V to 5.5 V - 4 - 4 A - 50 - 75 A - 50 - 75 A - 50 - 75 A A port; VI = 0 V or VCCI; IO = 0 A [1] B port; VI = 0 V or VCCI; IO = 0 A A plus B port (ICC(A) ICC(B)); IO = 0 A; VI = 0 V or VCCI ICC additional VCC(A), VCC(B) = 3.0 V to 5.5 V supply current A port; A port at VCC(A) 0.6 V; DIR at VCC(A); B port = open [4] DIR input; DIR at VCC(A) 0.6 V; A port at VCC(A) or GND; B port = open B port; B port at VCC(B) 0.6 V; DIR at GND; A port = open [1] [4] VCCI is the supply voltage associated with the data input port. [2] VCCO is the supply voltage associated with the output port. [3] To guarantee the node switches, an external driver must source/sink at least IBHLO/IBHHO when the input is in the range VIL to VIH. [4] For non bus hold parts only (74LVC1T45). 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 8 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 11. Dynamic characteristics Table 9. Typical dynamic characteristics at VCC(A) = 1.2 V and Tamb = 25 C Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for waveforms see Figure 6 and Figure 7 Symbol Parameter tPLH tPHL tPHZ tPLZ [1] Unit 1.2 V 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V A to B 10.6 8.1 7.0 5.8 5.3 5.1 ns B to A 10.6 9.5 9.0 8.5 8.3 8.2 ns HIGH to LOW propagation delay A to B 10.1 7.1 6.0 5.3 5.2 5.4 ns B to A 10.1 8.6 8.1 7.8 7.6 7.6 ns HIGH to OFF-state propagation delay DIR to A 9.4 9.4 9.4 9.4 9.4 9.4 ns DIR to B 12.0 9.4 9.0 7.8 8.4 7.9 ns LOW to OFF-state propagation delay DIR to A 7.1 7.1 7.1 7.1 7.1 7.1 ns OFF-state to LOW propagation delay tPZL VCC(B) LOW to HIGH propagation delay OFF-state to HIGH propagation delay tPZH Conditions DIR to B 9.5 7.8 7.7 6.9 7.6 7.0 ns DIR to A [1] 20.1 17.3 16.7 15.4 15.9 15.2 ns DIR to B [1] 17.7 15.2 14.1 12.9 12.4 12.2 ns DIR to A [1] 22.1 18.0 17.1 15.6 16.0 15.5 ns DIR to B [1] 19.5 16.5 15.4 14.7 14.6 14.8 ns tPZH and tPZL are calculated values using the formula shown in Section 14.4 "Enable times" Table 10. Typical dynamic characteristics at VCC(B) = 1.2 V and Tamb = 25 C Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for waveforms see Figure 6 and Figure 7 Symbol Parameter tPLH tPHL tPHZ tPLZ [1] Unit 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V A to B 10.6 9.5 9.0 8.5 8.3 8.2 ns B to A 10.6 8.1 7.0 5.8 5.3 5.1 ns HIGH to LOW propagation delay A to B 10.1 8.6 8.1 7.8 7.6 7.6 ns B to A 10.1 7.1 6.0 5.3 5.2 5.4 ns HIGH to OFF-state propagation delay DIR to A 9.4 6.5 5.7 4.1 4.1 3.0 ns DIR to B 12.0 6.1 5.4 4.6 4.3 4.0 ns LOW to OFF-state propagation delay DIR to A 7.1 4.9 4.5 3.2 3.4 2.5 ns DIR to B 9.5 7.3 6.6 5.9 5.7 5.6 ns DIR to A [1] 20.1 15.4 13.6 11.7 11.0 10.7 ns DIR to B [1] 17.7 14.4 13.5 11.7 11.7 10.7 ns DIR to A [1] 22.1 13.2 11.4 9.9 9.5 9.4 ns DIR to B [1] 19.5 15.1 13.8 11.9 11.7 10.6 ns OFF-state to LOW propagation delay tPZL VCC(A) 1.2 V LOW to HIGH propagation delay OFF-state to HIGH propagation delay tPZH Conditions tPZH and tPZL are calculated values using the formula shown in Section 14.4 "Enable times" 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 9 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 11. Typical power dissipation capacitance at VCC(A) = VCC(B) and Tamb = 25 C [1][2] Voltages are referenced to GND (ground = 0 V). Symbol Parameter power dissipation capacitance CPD [1] Conditions VCC(A) and VCC(B) Unit 1.8 V 2.5 V 3.3 V 5.5 V A port: (direction A to B); B port: (direction B to A) 2 3 3 4 pF A port: (direction B to A); B port: (direction A to B) 15 16 16 18 pF CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD VCC2 fi N + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; (CL VCC2 fo) = sum of the outputs. [2] fi = 10 MHz; VI = GND to VCC; tr = tf = 1 ns; CL = 0 pF; RL = . Table 12. Dynamic characteristics for temperature range 40 C to +85 C Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V Min Max Min Max Min Max Min Max Min Max VCC(A) = 1.4 V to 1.6 V tPLH LOW to HIGH propagation delay A to B 2.8 21.3 2.4 17.6 2.0 13.5 1.7 11.8 1.6 10.5 ns B to A 2.8 21.3 2.6 19.1 2.3 14.9 2.3 12.4 2.2 12.0 ns tPHL HIGH to LOW propagation delay A to B 2.6 19.3 2.2 15.3 1.8 11.8 1.7 10.9 1.7 10.8 ns B to A 2.6 19.3 2.4 17.3 2.3 13.2 2.2 11.3 2.3 11.0 3.0 18.7 ns ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B 3.0 18.7 3.0 18.7 3.0 18.7 3.0 18.7 3.5 24.8 3.5 23.6 3.0 11.0 3.3 11.3 2.8 10.3 ns tPLZ LOW to OFF-state propagation delay 2.4 11.4 2.4 11.4 2.4 11.4 2.4 11.4 2.4 11.4 ns 9.4 ns tPZH tPZL DIR to A DIR to B 2.8 18.3 3.0 17.2 2.5 9.4 3.0 10.1 2.5 OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 39.6 - 36.3 - 24.3 - 22.5 - 21.4 ns [1] - 32.7 - 29.0 - 24.9 - 23.2 - 21.9 ns OFF-state to LOW propagation delay DIR to A [1] - 44.1 - 40.9 - 24.2 - 22.6 - 21.3 ns DIR to B [1] - 38.0 - 34.0 - 30.5 - 29.6 - 29.5 ns VCC(A) = 1.65 V to 1.95 V tPLH tPHL tPHZ tPLZ LOW to HIGH propagation delay A to B 2.6 19.1 2.2 17.7 2.2 9.3 1.7 7.2 1.4 6.8 B to A 2.4 17.6 2.2 17.7 2.3 16.0 2.1 15.5 1.9 15.1 ns HIGH to LOW propagation delay A to B 2.4 17.3 2.0 14.3 1.6 8.5 1.8 7.1 1.7 7.0 B to A 2.2 15.3 2.0 14.3 2.1 12.9 2.0 12.6 1.8 12.2 ns HIGH to OFF-state DIR to A propagation delay DIR to B 2.9 17.1 2.9 17.1 2.9 17.1 2.9 17.1 2.9 17.1 ns 3.2 24.1 3.2 21.9 2.7 11.5 3.0 10.3 2.5 8.2 LOW to OFF-state propagation delay DIR to A 2.4 10.5 2.4 10.5 2.4 10.5 2.4 10.5 2.4 10.5 ns DIR to B 2.5 17.6 2.6 16.0 2.2 9.2 2.7 8.4 2.4 6.4 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 ns ns ns ns (c) NXP B.V. 2012. All rights reserved. 10 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 12. Dynamic characteristics for temperature range 40 C to +85 C ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V tPZH tPZL Min Max Min Max Min Max Min Max Min OFF-state to HIGH DIR to A propagation delay DIR to B [1] Max - 35.2 - 33.7 - 25.2 - 23.9 - 21.8 ns [1] - 29.6 - 28.2 - 19.8 - 17.7 - 17.3 ns OFF-state to LOW propagation delay DIR to A [1] - 39.4 - 36.2 - 24.4 - 22.9 - 20.4 ns DIR to B [1] - 34.4 - 31.4 - 25.6 - 24.2 - 24.1 ns VCC(A) = 2.3 V to 2.7 V LOW to HIGH propagation delay A to B 2.3 17.9 2.3 16.0 1.5 8.5 1.3 6.2 1.1 4.8 ns B to A 2.0 13.5 2.2 9.3 1.5 8.5 1.4 8.0 1.0 7.5 ns tPHL HIGH to LOW propagation delay A to B 2.3 15.8 2.1 12.9 1.4 7.5 1.3 5.4 0.9 4.6 ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B tPLH B to A 11.8 1.9 8.5 1.4 7.5 1.3 7.0 0.9 6.2 ns 8.1 2.1 8.1 2.1 8.1 2.1 8.1 2.1 8.1 ns 3.0 22.5 3.0 21.4 2.5 11.0 2.8 9.3 2.3 6.9 ns 1.7 5.8 1.7 5.8 1.7 5.8 1.7 5.8 1.7 5.8 ns 5.3 ns tPLZ LOW to OFF-state propagation delay 2.3 14.6 2.5 13.2 2.0 9.0 2.5 8.4 1.8 tPZH OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 28.1 - 22.5 - 17.5 - 16.4 - 12.8 ns [1] - 23.7 - 21.8 - 14.3 - 12.0 - 10.6 ns OFF-state to LOW propagation delay DIR to A [1] - 34.3 - 29.9 - 18.5 - 16.3 - 13.1 ns DIR to B [1] - 23.9 - 21.0 - 15.6 - 13.5 - 12.7 ns tPZL DIR to A 1.8 2.1 DIR to B VCC(A) = 3.0 V to 3.6 V tPLH tPHL tPHZ tPLZ tPZH tPZL LOW to HIGH propagation delay A to B 2.3 17.1 2.1 15.5 1.4 8.0 0.8 5.6 0.7 4.4 ns B to A 1.7 11.8 1.7 7.2 1.3 6.2 0.7 5.6 0.6 5.4 ns HIGH to LOW propagation delay A to B 2.2 15.6 2.0 12.6 1.3 7.0 0.8 5.0 0.7 4.0 ns B to A 1.7 10.9 1.8 7.1 1.3 5.4 0.8 5.0 0.7 4.5 ns HIGH to OFF-state DIR to A propagation delay DIR to B 2.3 7.3 2.3 7.3 2.3 7.3 2.3 7.3 2.7 7.3 ns 2.9 18.0 2.9 16.5 2.3 10.1 2.7 8.6 2.2 6.3 ns LOW to OFF-state propagation delay DIR to A 2.0 5.6 2.0 5.6 2.0 5.6 2.0 5.6 2.0 5.6 ns DIR to B 2.3 13.6 2.4 12.5 1.9 7.8 2.3 7.1 1.7 4.9 ns OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 25.4 - 19.7 - 14.0 - 12.7 - 10.3 ns [1] - 22.7 - 21.1 - 13.6 - 11.2 - 10.0 ns OFF-state to LOW propagation delay DIR to A [1] - 28.9 - 23.6 - 15.5 - 13.6 - 10.8 ns DIR to B [1] - 22.9 - 19.9 - 14.3 - 12.3 - 11.3 ns 15.1 1.0 7.5 0.7 5.4 0.5 3.9 ns VCC(A) = 4.5 V to 5.5 V tPLH LOW to HIGH propagation delay A to B 2.2 16.6 1.9 B to A 1.6 10.5 1.4 6.8 1.0 4.8 0.7 4.4 0.5 3.9 ns tPHL HIGH to LOW propagation delay A to B 2.3 15.3 1.8 12.2 1.0 6.2 0.7 4.5 0.5 3.5 ns B to A 1.7 10.8 1.7 7.0 0.9 4.6 0.7 4.0 0.5 3.5 ns 1.7 5.4 1.7 5.4 1.7 5.4 1.7 5.4 1.7 5.4 ns 2.9 17.3 2.9 16.1 2.3 9.7 2.7 8.0 2.5 5.7 ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 11 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 12. Dynamic characteristics for temperature range 40 C to +85 C ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V Min tPLZ tPZH tPZL [1] LOW to OFF-state propagation delay Max Min Max Min Max Min Max Min Max DIR to A 1.4 3.7 1.4 3.7 1.3 3.7 1.0 3.7 0.9 3.7 ns DIR to B 2.3 13.1 2.4 12.1 1.9 7.4 2.3 7.0 1.8 4.5 ns OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 23.6 - 18.9 - 12.2 - 11.4 - 8.4 ns [1] - 20.3 - 18.8 - 11.2 - 9.1 - 7.6 ns OFF-state to LOW propagation delay DIR to A [1] - 28.1 - 23.1 - 14.3 - 12.0 - 9.2 ns DIR to B [1] - 20.7 - 17.6 - 11.6 - 9.9 - 8.9 ns tPZH and tPZL are calculated values using the formula shown in Section 14.4 "Enable times" Table 13. Dynamic characteristics for temperature range 40 C to +125 C Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V Min Max Min Max Min Max Min Max Min Max VCC(A) = 1.4 V to 1.6 V tPLH tPHL tPHZ tPLZ tPZH tPZL LOW to HIGH propagation delay A to B 2.5 23.5 2.1 19.4 1.8 14.9 1.5 13.0 1.4 11.6 B to A 2.5 23.5 2.3 21.1 2.0 16.4 2.0 13.7 1.9 13.2 ns HIGH to LOW propagation delay A to B 2.3 21.3 1.9 16.9 1.6 13.0 1.5 12.0 1.5 11.9 B to A 2.3 21.3 2.1 19.1 2.0 14.6 1.9 12.5 2.0 12.1 ns 2.7 20.6 2.7 20.6 2.7 20.6 2.7 20.6 2.7 20.6 ns 3.1 27.3 3.1 26.0 2.7 12.1 2.9 12.5 2.5 11.4 HIGH to OFF-state DIR to A propagation delay DIR to B LOW to OFF-state propagation delay ns ns ns DIR to A 2.1 12.6 2.1 12.6 2.1 12.6 2.1 12.6 2.1 12.6 ns DIR to B 2.5 20.2 2.7 19.0 2.2 10.4 2.7 11.2 2.2 10.4 ns OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 43.7 - 40.1 - 26.8 - 24.9 - 23.6 ns [1] - 36.1 - 32.0 - 27.5 - 25.6 - 24.2 ns OFF-state to LOW propagation delay DIR to A [1] - 48.6 - 45.1 - 26.7 - 25.0 - 23.5 ns DIR to B [1] - 41.9 - 37.5 - 33.6 - 32.6 - 32.5 ns 21.1 1.9 19.5 1.9 10.3 1.5 8.0 1.2 7.5 VCC(A) = 1.65 V to 1.95 V tPLH LOW to HIGH propagation delay A to B 2.3 B to A 2.1 19.4 1.9 19.5 2.0 17.6 1.8 17.1 1.7 16.7 ns tPHL HIGH to LOW propagation delay A to B 2.1 19.1 1.8 15.8 1.4 9.4 1.6 7.9 1.5 7.7 B to A 1.9 16.9 1.8 15.8 1.8 14.2 1.8 13.9 1.6 13.5 ns 2.6 18.9 2.6 18.9 2.6 18.9 2.6 18.9 2.6 18.9 ns 2.8 26.6 2.8 24.1 2.4 12.7 2.7 11.4 2.2 9.1 ns 2.1 11.6 2.1 11.6 2.1 11.6 2.1 11.6 2.1 11.6 ns 7.4 ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B tPLZ LOW to OFF-state propagation delay tPZH DIR to A DIR to B OFF-state to HIGH DIR to A propagation delay DIR to B 74LVC_LVCH1T45 Product data sheet ns ns 2.2 19.4 2.3 17.6 1.9 10.2 2.4 9.3 2.1 [1] - 38.8 - 37.1 - 27.8 - 26.4 - 24.1 ns [1] - 32.7 - 31.1 - 21.9 - 19.6 - 19.1 ns All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 12 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 13. Dynamic characteristics for temperature range 40 C to +125 C ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V tPZL OFF-state to LOW propagation delay Min Max Min Max Min Max Min Max Min DIR to A [1] Max - 43.5 - 39.9 - 26.9 - 25.3 - 22.6 ns DIR to B [1] - 38.0 - 34.7 - 28.3 - 26.8 - 26.6 ns VCC(A) = 2.3 V to 2.7 V tPLH LOW to HIGH propagation delay A to B 2.0 19.7 2.0 17.6 1.3 9.4 1.1 6.9 0.9 5.3 ns B to A 1.8 14.9 1.9 10.3 1.3 9.4 1.2 8.8 0.9 8.3 ns tPHL HIGH to LOW propagation delay A to B 2.0 17.4 1.8 14.2 1.2 8.3 1.1 6.0 0.8 5.1 ns B to A 1.6 13.0 1.7 9.4 1.2 8.3 1.1 7.7 0.8 6.9 ns 1.8 9.0 ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B 1.8 9.0 1.8 9.0 1.8 9.0 1.8 9.0 2.7 24.8 2.7 23.6 2.2 12.1 2.5 10.3 2.0 7.6 ns tPLZ LOW to OFF-state propagation delay 1.5 6.4 1.5 6.4 1.5 6.4 1.5 6.4 1.5 6.4 ns 5.9 ns tPZH tPZL DIR to A DIR to B 2.0 16.1 2.2 14.6 1.8 9.9 2.2 9.3 1.6 OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 31.0 - 24.9 - 19.3 - 18.1 - [1] - 26.1 - 24.0 - 15.8 - 13.3 - 11.7 OFF-state to LOW propagation delay DIR to A [1] - 37.8 - 33.0 - 20.4 - 18.0 - 14.5 ns DIR to B [1] - 26.4 - 23.2 - 17.3 - 15.0 - 14.1 ns 14.2 ns ns VCC(A) = 3.0 V to 3.6 V tPLH tPHL tPHZ tPLZ tPZH tPZL LOW to HIGH propagation delay A to B 2.0 18.9 1.8 17.1 1.2 8.8 0.7 6.2 0.6 4.9 ns B to A 1.5 13.0 1.5 8.0 1.1 6.9 0.6 6.2 0.5 6.0 ns HIGH to LOW propagation delay A to B 1.9 17.2 1.8 13.9 1.1 7.7 0.7 5.5 0.6 4.4 ns B to A 1.5 12.0 1.6 7.9 1.1 6.0 0.7 5.5 0.6 5.0 ns HIGH to OFF-state DIR to A propagation delay DIR to B 2.0 8.1 2.0 8.1 2.0 8.1 2.0 8.1 2.4 8.1 ns 2.6 19.8 2.6 18.2 2.0 11.2 2.4 9.5 1.9 7.0 ns LOW to OFF-state propagation delay 1.8 6.2 1.8 6.2 1.8 6.2 1.8 6.2 1.8 6.2 ns DIR to A DIR to B 2.0 15.0 2.1 13.8 1.7 8.6 2.0 7.9 1.5 5.4 ns OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 28.0 - 21.8 - 15.5 - 14.1 - 11.4 ns [1] - 25.1 - 23.3 - 15.0 - 12.4 - 11.1 ns OFF-state to LOW propagation delay DIR to A [1] - 31.8 - 26.1 - 17.2 - 15.0 - 12.0 ns DIR to B [1] - 25.3 - 22.0 - 15.8 - 13.6 - 12.5 ns VCC(A) = 4.5 V to 5.5 V LOW to HIGH propagation delay A to B 1.9 18.3 1.7 16.7 0.9 8.3 0.6 6.0 0.4 4.3 ns B to A 1.4 11.6 1.2 7.5 0.9 5.3 0.6 4.9 0.4 4.3 ns tPHL HIGH to LOW propagation delay A to B 2.0 16.9 1.6 13.5 0.9 6.9 0.6 5.0 0.4 3.9 ns 1.5 11.9 1.5 7.7 0.8 5.1 0.6 4.4 0.4 3.9 ns tPHZ HIGH to OFF-state DIR to A propagation delay DIR to B 1.5 6.0 1.5 6.0 1.5 6.0 1.5 6.0 1.5 6.0 ns 2.6 19.1 2.6 17.8 2.0 10.7 2.4 8.8 2.2 6.3 ns LOW to OFF-state propagation delay DIR to A 1.2 4.1 1.2 4.1 1.1 4.1 0.9 4.1 0.8 4.1 ns DIR to B 2.0 14.5 2.1 13.4 1.7 8.2 2.0 7.7 1.6 5.0 ns tPLH tPLZ 74LVC_LVCH1T45 Product data sheet B to A All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 13 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 13. Dynamic characteristics for temperature range 40 C to +125 C ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8; for wave forms see Figure 6 and Figure 7 Symbol Parameter Conditions VCC(B) Unit 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5.0 V 0.5 V tPZH tPZL [1] Min Max Min Max Min Max Min Max Min Max OFF-state to HIGH DIR to A propagation delay DIR to B [1] - 26.1 - 20.9 - 13.5 - 12.6 - 9.3 ns [1] - 22.4 - 20.8 - 12.4 - 10.1 - 8.4 ns OFF-state to LOW propagation delay DIR to A [1] - 31.0 - 25.5 - 15.8 - 13.2 - 10.2 ns DIR to B [1] - 22.9 - 19.5 - 12.9 - 11.0 - 9.9 ns tPZH and tPZL are calculated values using the formula shown in Section 14.4 "Enable times" 12. Waveforms VI VM A, B input GND tPLH tPHL VOH VM B, A output 001aae967 VOL Measurement points are given in Table 14. VOL and VOH are typical output voltage levels that occur with the output load. Fig 6. The data input (A, B) to output (B, A) propagation delay times VI DIR input VM GND t PLZ output LOW-to-OFF OFF-to-LOW t PZL VCCO VM VX VOL t PHZ VOH t PZH VY output HIGH-to-OFF OFF-to-HIGH VM GND outputs enabled outputs disabled outputs enabled 001aae968 Measurement points are given in Table 14. VOL and VOH are typical output voltage levels that occur with the output load. Fig 7. Enable and disable times 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 14 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Table 14. Measurement points Supply voltage Input[1] Output[2] VCC(A), VCC(B) VM VM VX VY 1.2 V to 1.6 V 0.5VCCI 0.5VCCO VOL + 0.1 V VOH 0.1 V 1.65 V to 2.7 V 0.5VCCI 0.5VCCO VOL + 0.15 V VOH 0.15 V 3.0 V to 5.5 V 0.5VCCI 0.5VCCO VOL + 0.3 V VOH 0.3 V [1] VCCI is the supply voltage associated with the data input port. [2] VCCO is the supply voltage associated with the output port. tW VI 90 % negative pulse VM VM 10 % 0V tf tr tr tf VI 90 % positive pulse VM VM 10 % 0V tW VEXT VCC VI RL VO G DUT RT RL CL 001aae331 Test data is given in Table 15. RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance. VEXT = External voltage for measuring switching times. Fig 8. Table 15. Test circuit for measuring switching times Test data Supply voltage Input VCC(A), VCC(B) VI[1] t/V[2] Load CL RL tPLH, tPHL tPZH, tPHZ tPZL, tPLZ[3] 1.2 V to 5.5 V VCCI 1.0 ns/V 15 pF 2 k open GND 2VCCO [1] VCCI is the supply voltage associated with the data input port. [2] dV/dt 1.0 V/ns [3] VCCO is the supply voltage associated with the output port. 74LVC_LVCH1T45 Product data sheet VEXT All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 15 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 13. Typical propagation delay characteristics 001aai907 14 tPHL (ns) 12 001aai908 14 tPLH (ns) 12 (1) (1) 10 10 (2) 8 (2) 8 (3) 6 (3) (4) (5) (6) 6 (4) (5) (6) 4 4 2 2 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai909 14 tPHL (ns) 12 0 5 10 15 20 25 35 30 CL (pF) b. LOW to HIGH propagation delay (A to B) 001aai910 14 tPLH (ns) 12 (1) (1) 10 (2) (3) 10 8 (4) (5) (6) 8 (2) (3) (4) (5) 6 6 4 4 2 2 0 (6) 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 9. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 1.2 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 16 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 001aai911 14 tPHL (ns) 12 001aai912 14 tPLH (ns) 12 (1) 10 10 (1) 8 8 (2) (2) (3) 6 6 (3) (4) (5) (6) (4) 4 4 (5) 2 2 (6) 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai913 14 tPHL (ns) 12 10 0 5 10 15 20 25 35 30 CL (pF) b. LOW to HIGH propagation delay (A to B) 001aai914 14 tPLH (ns) 12 10 (1) 8 (1) 8 6 (2) (3) (4) 6 (2) (3) (4) (5) (5) (6) (6) 4 4 2 2 0 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 10. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 1.5 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 17 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 001aai915 14 tPHL (ns) 12 001aai916 14 tPLH (ns) 12 (1) 10 10 (1) 8 8 (2) (2) 6 6 (3) 4 (4) (5) (6) (3) (4) 4 (5) (6) 2 2 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai917 14 tPHL (ns) 12 10 0 5 10 15 20 25 35 30 CL (pF) b. LOW to HIGH propagation delay (A to B) 001aai918 14 tPLH (ns) 12 10 8 8 (1) (1) 6 4 (2) (3) (4) (5) (6) 6 (2) (3) (4) (5) (6) 4 2 2 0 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 11. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 1.8 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 18 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 001aai919 14 tPHL (ns) 12 10 001aai920 14 tPLH (ns) 12 (1) 10 (1) 8 8 (2) (2) 6 6 (3) (3) 4 (4) (5) (6) 4 (4) (5) (6) 2 2 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai921 14 tPHL (ns) 12 0 8 8 20 25 (2) (3) (4) (5) (6) 35 30 CL (pF) 001aai922 (1) 6 (1) 2 15 14 tPLH (ns) 12 10 4 10 b. LOW to HIGH propagation delay (A to B) 10 6 5 (2) (3) (4) (5) (6) 4 2 0 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 12. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 2.5 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 19 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 001aai923 14 tPHL (ns) 12 10 001aai924 14 tPLH (ns) 12 10 (1) (1) 8 8 (2) (2) 6 6 (3) (3) 4 4 (4) (5) (6) 2 (4) (5) (6) 2 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai925 14 tPHL (ns) 12 0 8 8 (2) (3) (4) (5) (6) 4 2 0 15 20 25 35 30 CL (pF) 001aai926 14 tPLH (ns) 12 10 (1) 10 b. LOW to HIGH propagation delay (A to B) 10 6 5 6 (1) 4 (2) (3) 2 (4) (5) (6) 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 13. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 3.3 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 20 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 001aai927 14 tPHL (ns) 12 10 001aai928 14 tPLH (ns) 12 10 (1) (1) 8 8 (2) 6 (2) 6 (3) (3) 4 4 (4) (5) (6) 2 (4) (5) (6) 2 0 0 0 5 10 15 20 25 35 30 CL (pF) a. HIGH to LOW propagation delay (A to B) 001aai929 14 tPHL (ns) 12 0 5 10 15 20 25 35 30 CL (pF) b. LOW to HIGH propagation delay (A to B) 001aai930 14 tPLH (ns) 12 10 10 8 8 6 (1) 6 4 (2) (3) 4 (2) (3) 2 (4) (5) (6) 2 (4) (5) (6) 0 (1) 0 0 5 10 15 20 25 35 30 CL (pF) c. HIGH to LOW propagation delay (B to A) 0 5 10 15 20 25 35 30 CL (pF) d. LOW to HIGH propagation delay (B to A) (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. (6) VCC(B) = 5.0 V. Fig 14. Typical propagation delay vs load capacitance; Tamb = 25 C; VCC(A) = 5 V 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 21 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 14. Application information 14.1 Unidirectional logic level-shifting application The circuit given in Figure 15 is an example of the 74LVC1T45; 74LVCH1T45 being used in a unidirectional logic level-shifting application. 74LVC1T45 74LVCH1T45 VCC1 VCC1 VCC(A) GND A 1 6 2 5 3 4 system-1 VCC(B) DIR VCC2 VCC2 B system-2 001aaj994 Fig 15. Unidirectional logic level-shifting application Table 16. Pin 74LVC_LVCH1T45 Product data sheet Description unidirectional logic level-shifting application Name Function Description 1 VCC(A) VCC1 supply voltage of system-1 (1.2 V to 5.5 V) 2 GND GND device GND 3 A OUT output level depends on VCC1 voltage 4 B IN input threshold value depends on VCC2 voltage 5 DIR DIR the GND (LOW level) determines B port to A port direction 6 VCC(B) VCC2 supply voltage of system-2 (1.2 V to 5.5 V) All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 22 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 14.2 Bidirectional logic level-shifting application Figure 16 shows the 74LVC1T45; 74LVCH1T45 being used in a bidirectional logic level-shifting application. Since the device does not have an output enable pin, the system designer should take precautions to avoid bus contention between system-1 and system-2 when changing directions. 74LVC1T45 74LVCH1T45 VCC1 VCC1 VCC2 VCC(A) I/O-1 GND PULL-UP/DOWN A 1 6 2 5 3 4 VCC2 VCC(B) I/O-2 DIR PULL-UP/DOWN B DIR CTRL system-1 system-2 001aaj995 Pull-up or pull-down only needed for 74LVC1T45. Fig 16. Bidirectional logic level-shifting application Table 17 provides a sequence that illustrates data transmission from system-1 to system-2 and then from system-2 to system-1. Table 17. Description bidirectional logic level-shifting application[1] State DIR CTRL I/O-1 I/O-2 Description 1 H output input system-1 data to system-2 2 H Z Z system-2 is getting ready to send data to system-1. I/O-1 and I/O-2 are disabled. The bus-line state depends on bus hold. 3 L Z Z DIR bit is set LOW. I/O-1 and I/O-2 are still disabled. The bus-line state depends on bus hold. 4 L input output system-2 data to system-1 [1] H = HIGH voltage level; L = LOW voltage level; Z = high-impedance OFF-state. 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 23 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 14.3 Power-up considerations The device is designed such that no special power-up sequence is required other than GND being applied first. Table 18. VCC(A) Typical total supply current (ICC(A) + ICC(B)) VCC(B) Unit 0V 1.8 V 2.5 V 3.3 V 5.0 V 0V 0 <1 <1 <1 <1 A 1.8 V <1 <2 <2 <2 2 A 2.5 V <1 <2 <2 <2 <2 A 3.3 V <1 <2 <2 <2 <2 A 5.0 V <1 2 <2 <2 <2 A 14.4 Enable times Calculate the enable times for the 74LVC1T45; 74LVCH1T45 using the following formulas: * * * * tPZH (DIR to A) = tPLZ (DIR to B) + tPLH (B to A) tPZL (DIR to A) = tPHZ (DIR to B) + tPHL (B to A) tPZH (DIR to B) = tPLZ (DIR to A) + tPLH (A to B) tPZL (DIR to B) = tPHZ (DIR to A) + tPHL (A to B) In a bidirectional application, these enable times provide the maximum delay from the time the DIR bit is switched until an output is expected. For example, if the 74LVC1T45; 74LVCH1T45 initially is transmitting from A to B, then the DIR bit is switched, the B port of the device must be disabled before presenting it with an input. After the B port has been disabled, an input signal applied to it appears on the corresponding A port after the specified propagation delay. 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 24 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 15. Package outline Plastic surface-mounted package; 6 leads SOT363 D E B y X A HE 6 5 v M A 4 Q pin 1 index A A1 1 2 e1 3 bp c Lp w M B e detail X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A1 max bp c D E e e1 HE Lp Q v w y mm 1.1 0.8 0.1 0.30 0.20 0.25 0.10 2.2 1.8 1.35 1.15 1.3 0.65 2.2 2.0 0.45 0.15 0.25 0.15 0.2 0.2 0.1 OUTLINE VERSION REFERENCES IEC JEDEC SOT363 JEITA SC-88 EUROPEAN PROJECTION ISSUE DATE 04-11-08 06-03-16 Fig 17. Package outline SOT363 (SC-88) 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 25 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state SOT886 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm b 1 2 3 4x (2) L L1 e 6 5 e1 4 e1 6x A (2) A1 D E terminal 1 index area 0 1 2 mm scale Dimensions (mm are the original dimensions) Unit mm max nom min A(1) 0.5 A1 b D E 0.04 0.25 1.50 1.05 0.20 1.45 1.00 0.17 1.40 0.95 e e1 0.6 0.5 L L1 0.35 0.40 0.30 0.35 0.27 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. Outline version SOT886 sot886_po References IEC JEDEC JEITA European projection Issue date 04-07-22 12-01-05 MO-252 Fig 18. Package outline SOT886 (XSON6) 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 26 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm 1 SOT891 b 3 2 4x (1) L L1 e 6 5 e1 4 e1 6x A (1) A1 D E terminal 1 index area 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max A1 max b D E e e1 L L1 mm 0.5 0.04 0.20 0.12 1.05 0.95 1.05 0.95 0.55 0.35 0.35 0.27 0.40 0.32 Note 1. Can be visible in some manufacturing processes. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 05-04-06 07-05-15 SOT891 Fig 19. Package outline SOT891 (XSON6) 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 27 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state XSON6: extremely thin small outline package; no leads; 6 terminals; body 0.9 x 1.0 x 0.35 mm 1 SOT1115 b 3 2 (4x)(2) L L1 e 6 5 4 e1 e1 (6x)(2) A1 A D E terminal 1 index area 0 0.5 scale Dimensions Unit mm 1 mm A(1) A1 b D E e e1 max 0.35 0.04 0.20 0.95 1.05 nom 0.15 0.90 1.00 0.55 min 0.12 0.85 0.95 0.3 L L1 0.35 0.40 0.30 0.35 0.27 0.32 Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. Outline version sot1115_po References IEC JEDEC JEITA European projection Issue date 10-04-02 10-04-07 SOT1115 Fig 20. Package outline SOT1115 (XSON6) 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 28 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state XSON6: extremely thin small outline package; no leads; 6 terminals; body 1.0 x 1.0 x 0.35 mm 1 SOT1202 b 3 2 (4x)(2) L L1 e 6 5 4 e1 e1 (6x)(2) A1 A D E terminal 1 index area 0 0.5 scale Dimensions Unit mm 1 mm A(1) A1 b D E e e1 L L1 max 0.35 0.04 0.20 1.05 1.05 0.35 0.40 nom 0.15 1.00 1.00 0.55 0.35 0.30 0.35 min 0.12 0.95 0.95 0.27 0.32 Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. Outline version sot1202_po References IEC JEDEC JEITA European projection Issue date 10-04-02 10-04-06 SOT1202 Fig 21. Package outline SOT1202 (XSON6) 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 29 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 16. Abbreviations Table 19. Abbreviations Acronym Description CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model 17. Revision history Table 20. Revision history Document ID Release date Data sheet status Change notice Supersedes 74LVC_LVCH1T45 v.6 20120806 Product data sheet - 74LVC_LVCH1T45 v.5 Modifications: 74LVC_LVCH1T45 v.5 Modifications: * Package outline drawing of SOT886 (Figure 18) modified. 20111219 * Product data sheet - 74LVC_LVCH1T45 v.4 Legal pages updated. 74LVC_LVCH1T45 v.4 20110927 Product data sheet - 74LVC_LVCH1T45 v.3 74LVC_LVCH1T45 v.3 20100819 Product data sheet - 74LVC_LVCH1T45 v.2 74LVC_LVCH1T45 v.2 20100119 Product data sheet - 74LVC_LVCH1T45 v.1 74LVC_LVCH1T45 v.1 20090511 Product data sheet - - 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 30 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. 74LVC_LVCH1T45 Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 31 of 33 74LVC1T45; 74LVCH1T45 NXP Semiconductors Dual supply translating transceiver; 3-state Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com 74LVC_LVCH1T45 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 -- 6 August 2012 (c) NXP B.V. 2012. All rights reserved. 32 of 33 NXP Semiconductors 74LVC1T45; 74LVCH1T45 Dual supply translating transceiver; 3-state 20. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 18 18.1 18.2 18.3 18.4 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Typical propagation delay characteristics . . 16 Application information. . . . . . . . . . . . . . . . . . 22 Unidirectional logic level-shifting application . 22 Bidirectional logic level-shifting application. . . 23 Power-up considerations . . . . . . . . . . . . . . . . 24 Enable times . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 25 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 30 Legal information. . . . . . . . . . . . . . . . . . . . . . . 31 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 31 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Contact information. . . . . . . . . . . . . . . . . . . . . 32 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 6 August 2012 Document identifier: 74LVC_LVCH1T45