SEK IEC 60 603-13 Number of contacts 6--64 Male header with angled solder pins and board lock No. of contacts Identification Without levers Part No. With short levers With long levers Male header with angled solder pins and pcb board lock SEK Length: 2.9 mm for 1.6 mm pcb thickness 09 . 10 6 09 18 506 973* 09 18 506 963* 09 18 506 953* 10 09 18 510 973* 09 18 510 963* 09 18 510 953* 14 09 18 514 973* 98 18 514 963* 09 18 514 953* 16 09 18 516 973* 09 18 516 963* 09 18 516 953* 20 09 18 520 973* 09 18 520 963* 09 18 520 953* 26 09 18 526 973* 09 18 526 963* 09 18 526 953* 34 09 18 534 973* 09 18 534 963* 09 18 534 953* 40 09 18 540 973* 09 18 540 963* 09 18 540 953* 50 09 18 550 973* 09 18 550 963* 09 18 550 953* 60 09 18 560 973* 09 18 560 963* 09 18 560 953* 64 09 18 564 973* 09 18 564 963* 09 18 564 953* To hold the connector on the pcb before the soldering process, two board locks have been added on the male header with angled solder pins. * Not normally kept in stock 30 contacts on request For performance level 3 please specify digit For performance level 2 please specify digit > 0.76 m Au (30 inch) on request 7 6 5 7 6 5 7 6 5 SEK IEC 60 603-13 Number of contacts 6--64 Male header with angled solder pins and board lock Identification Drawing Male header No. of A contacts 6 26.9 10 32.0 14 37.1 16 39.6 20 44.7 26 52.3 34 62.5 40 70.1 50 82.8 60 95.5 64 100.6 Dimensions in mm B D 16.76 21.84 26.92 29.46 34.54 42.16 52.32 59.94 72.64 85.34 90.42 12.45 17.53 22.61 25.15 30.23 37.85 48.01 55.63 68.33 81.03 86.11 2.54 2.54 2.54 2.54 2.54 2.54 2.54 2.54 2.54 2.54 2.54 E F x 2= x 4= x 6= x 7= x 9= x 12 = x 16 = x 19 = x 24 = x 29 = x 31 = 5.08 36.9 40.3 10.16 42.0 45.4 15.24 47.1 50.4 17.78 49.6 53.0 22.86 54.7 58.1 30.48 62.3 65.7 40.64 72.5 75.8 48.26 80.1 83.5 60.96 92.8 96.2 73.66 105.5 108.9 78.74 110.6 113.9 G Short levers SEK for use with female connector without strain relief clamp Long levers for use with female connector with strain relief clamp Board drillings 09 . 11 For accessories see page 09.14 1) 2) Contact number 1 No polarization slot for 6, 10 or 14 way male header 3) No polarization slot for 6 way male header 4) Pitch tolerance: 0.1