SEK
SEK IEC 60 603-13
6 09 18 506 973* 09 18 506 963* 09 18 506 953*
10 09 18 510 973* 09 18 510 963* 09 18 510 953*
14 09 18 514 973* 98 18 514 963* 09 18 514 953*
16 09 18 516 973* 09 18 516 963* 09 18 516 953*
20 09 18 520 973* 09 18 520 963* 09 18 520 953*
26 09 18 526 973* 09 18 526 963* 09 18 526 953*
34 09 18 534 973* 09 18 534 963* 09 18 534 953*
40 09 18 540 973* 09 18 540 963* 09 18 540 953*
50 09 18 550 973* 09 18 550 963* 09 18 550 953*
60 09 18 560 973* 09 18 560 963* 09 18 560 953*
64 09 18 564 973* 09 18 564 963* 09 18 564 953*
777
666
555
09
.
10
No. of Part No.
Identification contacts Without levers With short levers With long levers
Male header with angled solder pins and board lock
Number of contacts
6--64
Male header with
angled solder pins
and pcb board lock
Length: 2.9 mm
for 1.6 mm pcb thickness
To hold the connector on the pcb before the soldering
process, two board locks have been added on the male
header with angled solder pins.
For performance level 3 please specify digit
For performance level 2 please specify digit
> 0.76 µm Au (30 µinch) on request
* Not normally kept in stock
30 contacts on request
SEK
09
.
11
SEK IEC 60 603-13
Male header
Board drillings
Identification Drawing Dimensions in mm
For accessories see page 09.14
No. of ABD E FG
contacts
6 26.9 16.76 12.45 2.54 x 2 = 5.08 36.9 40.3
10 32.0 21.84 17.53 2.54 x 4 = 10.16 42.0 45.4
14 37.1 26.92 22.61 2.54 x 6 = 15.24 47.1 50.4
16 39.6 29.46 25.15 2.54 x 7 = 17.78 49.6 53.0
20 44.7 34.54 30.23 2.54 x 9 = 22.86 54.7 58.1
26 52.3 42.16 37.85 2.54 x 12 = 30.48 62.3 65.7
34 62.5 52.32 48.01 2.54 x 16 = 40.64 72.5 75.8
40 70.1 59.94 55.63 2.54 x 19 = 48.26 80.1 83.5
50 82.8 72.64 68.33 2.54 x 24 = 60.96 92.8 96.2
60 95.5 85.34 81.03 2.54 x 29 = 73.66 105.5 108.9
64 100.6 90.42 86.11 2.54 x 31 = 78.74 110.6 113.9
Short levers
for use with female
connector without
strain relief clamp
Long levers
for use with female
connector with
strain relief clamp
Male header with angled solder pins and board lock
Number of contacts
6--64
1) Contact number 1
2) No polarization slot
for 6, 10 or 14 way male header
3) No polarization slot
for 6 way male header
4) Pitch tolerance: ± 0.1
