VIN
VCC
RT
SS GND
VFB
COMP
CS
OUT1
OUT2
ISOLATED
FEEDBACK
LM5030
VIN VOUT
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
Reference
Design
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
LM5030 100-V Push-Pull Current Mode PWM Controller
1 Features 3 Description
The LM5030 high-voltage PWM controller contains all
1• Internal High-Voltage Start-Up Regulator of the features needed to implement push-pull and
• Single Resistor Oscillator Setting bridge topologies, using current-mode control in a
• Synchronizable small 10-pin package. This device provides two
alternating gate driver outputs. The LM5030 includes
• Error Amplifier a high-voltage start-up regulator that operates over a
• Precision Reference wide input range of 14 V to 100 V. Additional features
• Adjustable Softstart include: error amplifier, precision reference, dual
mode current limit, slope compensation, softstart,
• Dual Mode Overcurrent Protection sync capability, and thermal shutdown. This high
• Slope Compensation speed IC has total propagation delays less than
• Direct Optocoupler Interface 100 ns and a 1-MHz capable single-resistor
• 1.5-A Peak Gate Drivers adjustable oscillator.
• Thermal Shutdown Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
2 Applications VSSOP (10) 3.00 mm × 3.00 mm
• Telecommunication Power Converters LM5030 WSON (10) 4.00 mm × 4.00 mm
• Industrial Power Converters (1) For all available packages, see the orderable addendum at
• +42-V Automotive Systems the end of the data sheet.
Typical Application Diagram
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 13
1 Features.................................................................. 18 Application and Implementation ........................ 14
2 Applications ........................................................... 18.1 Application Information............................................ 14
3 Description............................................................. 18.2 Typical Application ................................................. 14
4 Revision History..................................................... 29 Power Supply Recommendations...................... 20
5 Pin Configuration and Functions......................... 310 Layout................................................................... 20
6 Specifications......................................................... 410.1 Layout Guidelines ................................................. 20
6.1 Absolute Maximum Ratings ...................................... 410.2 Layout Example .................................................... 20
6.2 ESD Ratings.............................................................. 411 Device and Documentation Support................. 21
6.3 Recommended Operating Conditions....................... 411.1 Device Support...................................................... 21
6.4 Thermal Information.................................................. 411.2 Documentation Support ....................................... 21
6.5 Electrical Characteristics........................................... 511.3 Community Resources.......................................... 21
6.6 Typical Characteristics.............................................. 811.4 Trademarks........................................................... 21
7 Detailed Description............................................ 10 11.5 Electrostatic Discharge Caution............................ 21
7.1 Overview................................................................. 10 11.6 Glossary................................................................ 21
7.2 Functional Block Diagram....................................... 10 12 Mechanical, Packaging, and Orderable
7.3 Feature Description................................................. 11 Information ........................................................... 21
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (March 2013) to Revision D Page
• Added ESD Ratings table, Thermal Information table, Feature Description section, Device Functional Modes,
Application and Implementation section, Power Supply Recommendations section, Layout section, Device and
Documentation Support section, and Mechanical, Packaging, and Orderable Information section....................................... 1
Changes from Revision B (March 2013) to Revision C Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 16
2Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
1
2
3
4
56
7
8
9
10
VFB
VCC
OUT1
VIN
COMP
OUT2
GND
CS
RT
SS
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
5 Pin Configuration and Functions
DGS, DPR Package
10-Pin VSSOP, WSON
Top View
Pin Functions
PIN I/O DESCRIPTION APPLICATION INFORMATION
NAME NO.
There is an internal 5-kΩpullup resistor on this pin. The
COMP 3 O Output to the error amplifier error amplifier provides an active sink.
Current sense input for current mode control and current
limit sensing. Using separate dedicated comparators, if CS
CS 8 I Current sense input exceeds 0.5 V, the outputs will go into cycle-by-cycle
current limit. If CS exceeds 0.625 V the outputs will be
disabled and a softstart commenced.
GND 7 — Return Ground
OUT1 5 O Output of the PWM controller Alternating PWM output gate driver
OUT2 6 O Output of the PWM controller Alternating PWM output gate driver
An external resistor sets the oscillator frequency. This pin
Oscillator timing resistor pin and
RT 9 I will also accept synchronization pulses from an external
synchronization input oscillator.
A 10-µA current source and an external capacitor set the
softstart timing length. The controller will enter a low power
SS 10 I Dual purpose soft start and shutdown pin state if the SS pin is pulled below the typical shutdown
threshold of 0.45 V.
VIN 1 I Source input voltage Input to start-up regulator. Input range 14 to 100 V.
The non-inverting input is internally connected to a 1.25-V
VFB 2 I Inverting input to the error amplifier reference.
Output from the internal high-voltage series If an auxiliary winding raises the voltage on this pin above
VCC 4 I/O pass regulator. The regulation setpoint is the regulation setpoint, the internal series pass regulator
7.7 V. will shutdown, reducing the IC power dissipation.
The exposed die attach pad on the WSON package should
be connected to a PCB thermal pad at ground potential.
WSON SUB — Die substrate For additional information on using TI's No Pull Back
DAP WSON package, refer to WSON Application Note AN-1187
(SNOA401).
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM5030
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN MAX UNIT
VIN to GND (Survival) –0.3 100 V
VCC to GND (Survival) –0.3 16 V
RT to GND (Survival) –0.3 5.5 V
All other pins to GND (Survival) –0.3 7 V
Power dissipation Internally Limited
Lead temperature (soldering 4 seconds) 260 °C
Operating junction temperature 150 °C
Storage temperature, Tstg –55 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings VALUE UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000
V(ESD) Electrostatic discharge V
Machine model (MM) ±200
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
VIN 14 90 V
TJOperating junction temperature –40 105 °C
6.4 Thermal Information LM5030
THERMAL METRIC(1) DGS (VSSOP) DPR (WSON) UNIT
10 PINS 10 PINS
RθJA Junction-to-ambient thermal resistance 158.8 38.1 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 53.6 137.1 °C/W
RθJB Junction-to-board thermal resistance 74.8 15.2 °C/W
ψJT Junction-to-top characterization parameter 5.3 0.4 °C/W
ψJB Junction-to-board characterization parameter 77.6 15.4 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance — 4.6 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
6.5 Electrical Characteristics
Specifications are for TJ= 25°C. Unless otherwise specified: VIN = 48 V, VCC = 10 V, and RT = 26.7 kΩ
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
START-UP REGULATOR
TJ= 25°C 7.7
VCCReg VCC Regulation Open ckt V
full operating junction 7.4 8.0
temperature range
TJ= 25°C 17
VCC Current limit See Figure 2 mA
full operating junction 10
temperature range
TJ= 25°C 150
Start-up regulator leakage
I-VIN VIN = 90 V µA
full operating junction
(external VCC supply) 500
temperature range
TJ= 25°C 250
SS = 0 V, VCC =
IIN Shutdown current µA
full operating junction
open 350
temperature range
VCC SUPPLY
VCCReg –
TJ= 25°C 100 mV
VCC Undervoltage lockout V
voltage VCCReg –
full operating junction temperature range 300 mV
TJ= 25°C 1.6
Undervoltage hysteresis V
full operating junction temperature range 1.2 2.1
TJ= 25°C 2
ICC Supply current Cload = 0 mA
full operating junction 3
temperature range
ERROR AMPLIFIER
GBW Gain bandwidth 4 MHz
DC gain 75 dB
TJ= 25°C 1.245
Input voltage VFB = COMP V
full operating junction 1.220 1.270
temperature range
TJ= 25°C 13
VFB = 1.5 V COMP
COMP sink capability mA
full operating junction
= 1 V 5
temperature range
CURRENT LIMIT
TJ= 25°C 0.5
Cycle-by-cyble CS threshold
CS1 V
voltage full operating junction temperature range 0.45 0.55
TJ= 25°C 0.625
Resets SS
CS2 Restart CS threshold voltage capacitor; auto V
full operating junction 0.575 0.675
restart temperature range
CS step from 0-V to 0.6-V time-to-onset of OUT
ILIM delay to output transition (90%) 30 ns
Cload = 0 TJ= 25°C 6
CS sink current (clocked) CS = 0.3 V mA
full operating junction 3
temperature range
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control (SQC) methods. The limits are used to calculate TI's Average Outgoing Quality Level (AOQL).
(2) Typical numbers represent the most likely parametric norm for 25°C operation.
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM5030
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
Electrical Characteristics (continued)
Specifications are for TJ= 25°C. Unless otherwise specified: VIN = 48 V, VCC = 10 V, and RT = 26.7 kΩ
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
SOFT START AND SHUTDOWN
TJ= 25°C 10
Softstart current source µA
full operating junction temperature range 7 13
TJ= 25°C 0.5
Softstart to COMP offset V
full operating junction temperature range 0.25 0.75
TJ= 25°C 0.45
Shutdown threshold V
full operating junction temperature range 0.2 0.7
OSCILLATOR
TJ= 25°C 200
Frequency1 (RT = 26.7K) kHz
full operating junction temperature range 175 225
TJ= 25°C 600
Frequency2 (RT = 8.2K) kHz
full operating junction temperature range 510 690
TJ= 25°C 3.2
Sync threshold V
full operating junction temperature range 3.8
PWM COMPARATOR
COMP set to 2-V CS stepped 0 to 0.4 V, time-to-
Delay to output 30 ns
onset of OUT transition low
TJ= 25°C 49%
Inferred from
Max duty cycle full operating junction
deadtime 47.5% 50%
temperature range
full operating junction
Min duty cycle COMP = 0 V 0%
temperature range
COMP to PWM comparator 0.34 V / V
gain TJ= 25°C 5.2
COMP open circuit voltage VFB = 0 V V
full operating junction 4.3 6.1
temperature range
TJ= 25°C 1.1
VFB = 0 V, COMP =
COMP short circuit current mA
full operating junction
0 V 0.6 1.5
temperature range
SLOPE COMPENSATION
TJ= 25°C 105
Delta increase at
Slope comp amplitude PWM Comparator to mV
full operating junction 80 130
CS temperature range
OUTPUT SECTION
TJ= 25°C 135
Cload = 0, 10% to
Deadtime ns
full operating junction
10% 85 185
temperature range
TJ= 25°C 0.25
Iout = 50 mA, VCC –
Output high saturation V
full operating junction
VOUT 0.75
temperature range
TJ= 25°C 0.25
Output low saturation IOUT = 100 mA V
full operating junction 0.75
temperature range
Rise time Cload = 1 nF 16 ns
Fall time Cload = 1 nF 16 ns
6Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
Electrical Characteristics (continued)
Specifications are for TJ= 25°C. Unless otherwise specified: VIN = 48 V, VCC = 10 V, and RT = 26.7 kΩ
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
THERMAL SHUTDOWN
Thermal shutdown
Tsd 165 °C
temperature
Thermal shutdown hysteresis 15 °C
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM5030
DEADTIME (ns)
130
135
140
145
150
155
160
TEMPERATURE (oC)
-50 050 100 150
ISS (PA)
TEMPERATURE (oC)
-50 050 100 150
9.7
9.8
9.9
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.7
-50 0 50 100 150
TEMPERATURE (oC)
OSCILLATOR FREQUENCY (kHz)
199.0
199.5
200.0
200.5
201.0
201.5
202.0
202.5
203.0
100
1000
RT (K:)
OSCILLATOR FREQUENCY (kHz)
1 10 100
0 2 4 6 8 10 12 14 16
VIN (V)
0
2
4
6
8
10
12
14
16
VCC (V)
0 2 4 6 8 10 12 14 16 18 20
0
1
2
3
4
5
6
7
8
9
10
VCC (V)
ICC (mA)
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
6.6 Typical Characteristics
at TJ= 25°C (unless otherwise noted)
Figure 1. VCC vs VIN Figure 2. VCC vs ICC (VIN = 48 V)
Figure 3. Oscillator Frequency vs RT Figure 4. Oscillator Frequency vs Temperature RT = 26.7 kΩ
Figure 5. Softstart Current vs Temperature Figure 6. Deadtime vs Temperature
8Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LOGIC
OSC
VIN VCC
CS 0.5V
0.625V
LOGIC
OUT1
OUT2
GND
7.7V SERIES
REGULATOR
GENERATOR
REFERENCE
SLOPECOMP RAMP
GENERATOR
DRIVER
DRIVER
PWM
Rt / SYNC
45PA
0
CLK
SS
VCC
VCC
SHUTDOWN
COMPARATOR
ENABLE
ENABLE
2k
5V
1.25V
ERROR AMP
SOFT START 10PA
0.45V
VFB
5k
5V
1.4V
100k
50k
COMP
1.25V
SS
+
-
+
-
+
-
+
-
CLK
CLR
SET
JQ
K Q
CLR
SET
SQ
R Q
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LM5030 high-voltage PWM controller contains all of the features needed to implement push-pull and bridge
topologies, using current-mode control in a small 10-pin package. Features included are, start-up regulator, dual
mode current limit, dual alternating gate drivers, thermal shutdown, softstart, and slope compensation. This high
speed IC has total propagation delays < 100 ns. The functional block diagram of the LM5030 is shown in
Functional Block Diagram.
The LM5030 is designed for current-mode control converters that require alternating outputs, such as push-pull
and half- and full-bridge topologies. The features included in the LM5030 enable all of the advantages of current-
mode control, line feed-forward, cycle-by-cycle current limit, and simplified loop compensation. The oscillator
ramp is internally buffered and added to the PWM comparator input to provide the necessary slope
compensation for current-mode control at higher duty cycles.
7.2 Functional Block Diagram
10 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
7.3 Feature Description
7.3.1 High-Voltage Start-Up Regulator
The LM5030 contains an internal high-voltage start-up regulator. The input pin (VIN) can be connected directly to
line voltages as high as 100 V. The regulator output is internally current limited to 10 mA. Upon power up, the
regulator is enabled and sources current into an external capacitor connected to the VCC pin. The recommended
capacitance range for the VCC regulator is 0.1 µF to 50 µF. When the voltage on the VCC pin reaches the
regulation point of 7.7 V, the controller outputs are enabled. The outputs will remain enabled unless, VCC falls
below 6.1 V or if the SS/SHUTDOWN pin is pulled to ground or an over temperature condition occurs. In typical
applications, an auxiliary transformer winding is diode connected to the VCC pin. This winding raises the VCC
voltage greater than 8 V, effectively shutting off the internal start-up regulator and saving power while reducing
the controller dissipation. The external VCC capacitor must be sized such that the self-bias will maintain a VCC
voltage greater than 6.1 V during the initial start-up. During a fault mode when the converter self bias winding is
inactive, external current draw on the VCC line should be limited as to not exceed the maximum power dissipation
of the controller. An external start-up or other bias rail can be used instead of the internal start-up regulator by
connecting the VCC and the Vin pins and feeding the external bias voltage (8 V to 15 V) to that node.
7.3.2 Error Amplifier
An internal high gain error amplifier is provided within the LM5030. The noninverting reference of the amplifier is
tied to 1.25 V. In nonisolated applications the power converter output is connected to the VFB pin via the voltage
setting resistors and loop compensation is connected between the COMP and VFB pins.
For most isolated applications the error amplifier function is implemented on the secondary side ground. Because
the internal error amplifier is configured as an open drain output it can be disabled by connecting VFB to ground.
The internal 5-kΩpullup resistor, connected between the 5-V reference and COMP, can be used as the pullup
for an optocoupler or other isolation device.
7.3.3 PWM Comparator
The PWM comparator compares the compensated current ramp signal to the loop error voltage from the internal
error amplifier (COMP pin). This comparator is optimized for speed in order to achieve minimum discernable duty
cycles. The comparator polarity is such that 0 V on the COMP pin will cause a zero duty cycle.
7.3.4 Current Limit and Current Sense
The LM5030 contains two levels of over-current protection. If the voltage on the current sense comparator
exceeds 0.5 V the present cycle is terminated (cycle-by-cycle current limit). If the voltage on the current sense
comparator exceeds 0.625 V, the controller will terminate the present cycle and discharge the softstart capacitor.
A small RC filter, located near the controller, is recommended for the CS pin. An internal MOSFET discharges
the current sense filter capacitor at the conclusion of every cycle, to improve dynamic performance.
The LM5030 CS and PWM comparators are very fast, and as such will respond to short duration noise pulses.
Layout considerations are critical for the current sense filter and sense resistor. The capacitor associated with the
CS filter must be placed very close to the device and connected directly to the pins of the IC (CS and RTN). Also
if a current sense transformer is used, both leads of the transformer secondary should be routed to the sense
resistor, which should also be located close to the IC. If a current sense resistor located in the drive transistor
sources is used, for current sense, a low inductance resistor should be chosen. In this case all of the noise
sensitive low power grounds should be commoned together around the IC and then a single connection should
be made to the power ground (sense resistor ground point).
The second level threshold is intended to protect the power converter by initiating a low duty cycle hiccup mode
when abnormally high, fast rising currents occur. During excessive loading, the first level threshold will always be
reached and the output characteristic of the converter will be that of a current source but this sustained current
level can cause excessive temperatures in the power train especially the output rectifiers. If the second level
threshold is reached, the softstart capacitor will be fully discharged, a retry will commence following the
discharge detection. The second level threshold will only be reached when a high dV/dt is present at the current
sense pin. The signal must be fast enough to reach the second level threshold before the first threshold detector
turns off the driver. This can usually happen for a saturated power inductor or shorted load. Excessive filtering on
the CS pin, extremely low value current sense resistor or an inductor that does not saturate with excessive
loading may prevent the second level threshold from ever being reached.
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM5030
RT = (1/F) - 172 x 10-9
182 x 10-12
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
Feature Description (continued)
7.3.5 Oscillator, Shutdown and Sync Capability
The LM5030 oscillator is set by a single external resistor connected between the RT pin and return. To set a
desired oscillator frequency, the necessary RT resistor can be calculated in Equation 1:
(1)
Each output switches at half the oscillator frequency in a push-pull configuration. The LM5030 can also be
synchronized to an external clock. The external clock must be of higher frequency than the free running
frequency set by the RT resistor. The clock signal should be capacitively coupled into the RT pin with a 100-pF
capacitor. A peak voltage level greater than 3 V with respect to ground is required for detection of the sync pulse.
The sync pulse width should be set in the 15- to 150-ns range by the external components. The RT resistor is
always required, whether the oscillator is free running or externally synchronized. The voltage at the RT pin is
internally regulated to a nominal 2 V.
Locate the RT resistor close to the device and connected directly to the pins of the IC (RT and GND).
7.3.6 Slope Compensation
The PWM comparator compares the current sense signal to the voltage derived from the COMP pin. The COMP
voltage is set by either the internal error amplifier or an external error amplifier through an optocoupler. At duty
cycles greater than 50% (composite of alternating outputs) current mode control circuits are prone to
subharmonic oscillation. By adding an additional ramp signal to the current sense ramp signal this condition can
be avoided. The LM5030 integrates this slope compensation by buffering the internal oscillator ramp and
summing it internally to the current sense (CS) signal. Additional slope compensation may be added by
increasing the source impedance of the current sense signal.
7.3.7 Soft Start and Shutdown
The soft-start feature allows the converter to gradually reach the initial steady state operating point, thus reducing
start-up stresses and surges. An internal 10-μA current source and an external capacitor generate a ramping
voltage signal that limits the error amplifier output during start-up. In the event of a second level current limit fault,
the soft-start capacitor will be fully discharged which disables the output drivers. When the fault condition is no
longer present, the soft-start capacitor is released to ramp and gradually restart the converter. The SS pin can
also be used to disable the controller. If the SS pin voltage is pulled down below 0.45 V (nominal) the controller
will disable the outputs and enter a low power state.
7.3.8 OUT1, OUT2, and Time Delay
The LM5030 provides two alternating outputs, OUT1 and OUT2. The internal gate drivers can each sink 1.5-A
peak each. The maximum duty cycle for each output is inherently limited to less than 50%. The typical deadtime
between the falling edge of one gate driver output and the rising edge of the other gate driver output is 135 ns.
7.3.9 Thermal Protection
Internal thermal-shutdown circuitry is provided to protect the integrated circuit in the event the excessive junction
temperature. When activated, typically at 165°C, the controller is forced into a low-power reset state, disabling
the output drivers and the bias regulator. This feature is provided to prevent catastrophic failures from accidental
device overheating.
12 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
7.4 Device Functional Modes
The LM5030 is a versatile PWM controller that can be used in the following functional modes:
• The LM5030 provides a complete push-pull current mode current mode controller.
• The LM5030 driver outputs can be configured to drive high side MOSFETs through a gate driver chip to
implement half and full bridge topologies.
• The LM5030 can be configured in single ended outputs such as a flyback converter or boost.
• The LM5030 can also operate in conjunction with a high side driver chip to implement a synchronous buck
converter.
Details of these circuits can be found in Versatility of the LM5030 PWM Push-Pull Controller,SNVA548.
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM5030
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM5030 is a highly integrated PWM controller that contains all of the features necessary for implementing
push-pull topology power converters. The device targets DC-DC converter applications with input voltages of up
to 100 VDC and output power in the range 15 W to 150 W.
8.2 Typical Application
The schematic in Figure 8 shows an example of a 33-W push-pull converter controlled by a LM5030. The
operating input range is 36 V to 75 V, and the output voltage is 3.3 V. The output current capability is 10 A. The
converter is configured for input current protection with cycle-by-cycle current limit. An auxiliary winding is used
to raise the VCC voltage to reduce the controller power dissipation.
Figure 8. Typical Application Circuit, 36-V to 75-V IN and 3.3-V, 10-A OUT
14 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
0.0 2.0 4.0 6.0 8.0 10.0
10.5
10.6
10.7
10.8
10.9
11.0
11.1
11.2
11.3
VCC (V)
LOAD CURRENT (A)
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
Typical Application (continued)
8.2.1 Design Requirements
For this design example, use the input parameters listed in Table 1.
Table 1. Design Parameters
PARAMETER MIN NOM MAX UNIT
Input Voltage 36 75 V
Output Voltage 3.3 V
Output Current 0 10 A
Efficiency (Full Load) 82.5%
Efficiency (Half Load) 84.5%
Load Regulation 1%
Line Regulation 0.15%
Output Current Limit 11 A
8.2.2 Detailed Design Procedure
8.2.2.1 VCC
While the LM5030 internally generates a voltage at VCC (7.7 V), the internal regulator is used mainly during the
start-up sequence. Once the load current begins flowing through L2, which is both an inductor for the output filter
and a transformer, a voltage is generated at the secondary of L2, which powers the VCC pin. When the
externally applied voltage exceeds the internal value (7.7 V), the internal regulator shuts off, thereby reducing
internal power dissipation in the LM5030. L2 is constructed such that the voltage supplied to VCC ranges from
approximately 10.6 V to approximately 11.3 V, depending on the load current (see Figure 9).
Figure 9. VCC Voltage vs Load Current
8.2.2.2 Current Sense
Monitoring the input current provides a good indication of the operation of the circuit. If an overload condition
should exist at the output (a partial overload or a short circuit), the input current would rise above the nominal
value shown in Figure 12. Transformer T2, in conjunction with D3, R9, R12 and C10, provides a voltage to pin 8
on the LM5030 (CS) which is representative of the input current flowing through its primary. The average voltage
seen at pin 8 is plotted in Figure 10. If the voltage at the first current sense comparator exceeds 0.5 V, the
LM5030 disables its outputs, and the circuit enters a cycle-by-cycle current limit mode. If the second level
threshold (0.625 V) is exceeded due to a severe overload and transformer saturation, the LM5030 will disable its
outputs and initiate a softstart sequence. However, the very short propagation delay of the cycle-by-cycle current
limiter (CS1), the design of the CS filter (R9, R12, and C10), and the conservative design of the output inductor
(L2), may prevent the second level current threshold from being realized on this evaluation board.
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM5030
0.0 0.2 0.4 0.6 0.8 1.0
0.00
0.05
0.10
0.15
0.20
0.25
AVERAGE VOLTAGE @ CS (V)
INPUT CURRENT (A)
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
Figure 10. Average Voltage at the CS Pin vs Input Current
8.2.2.3 Shutdown
The Shutdown pad (SD) on the board connects to the SoftStart pin on the LM5030 (pin 10), and permits on/off
control of the converter by an external switch. SD should be pulled below 0.45 V, with an open collector or open
drain device, to shut down the LM5030 outputs and the VCC regulator. If the voltage at the SD pad is between
1.0 and 1.5 V, a partial-on condition results, which could be disruptive to the system. Therefore, the voltage at
the SD pad should transition quickly between its open circuit voltage (4.9 V) and ground.
8.2.2.4 External Sync
Although the LM5030 includes an internal oscillator, its operating frequency can be synchronized to an external
signal if desired. The external source frequency must be higher than the internal frequency set with the RT
resistor (262 kHz with RT= 20 kΩ). The sync input pulse width must be between 15 and 150 ns, and have an
amplitude of 1.5 to 3.0 V at the Sync pad on the board. The pulses are coupled to the LM5030 through a 100-pF
capacitor (C16) as specified in the data sheet.
Table 2. Bill of Materials
ITEM PART NUMBER DESCRIPTION VALUE
C 1 C0805C472K5RAC Capacitor, CER, KEMET 4700 p, 50 V
C 2 C0805C103K5RAC Capacitor, CER, KEMET 0.01 µ, 50 V
C 3 C4532X7S0G686M Capacitor, CER, TDK 68 µ, 4 V
C 4 T520D337M006AS4350 Capacitor, TANT, KEMET 330 µ, 6.3 V
C 5 T520D337M006AS4350 Capacitor, TANT, KEMET 330 µ, 6.3 V
C 6 C4532X7R3A103K Capacitor, CER, TDK 0.01 µ, 1000 V
C 7 C3216X7R2A104K Capacitor, CER, TDK 0.1 µ, 100 V
C 8 C4532X7R2A105M Capacitor, CER, TDK 1 µ, 100 V
C 9 C4532X7R2A105M Capacitor, CER, TDK 1 µ, 100 V
C 10 C0805C102K1RAC Capacitor, CER, KEMET 1000 p, 100 V
C 11 C1206C223K5RAC Capacitor, CER, KEMET 0.022 µ, 50 V
C 12 C3216X7R1E105M Capacitor, CER, TDK 1 µ, 25 V
C 13 C3216COG2J221J Capacitor, CER, TDK 220 p, 630 V
C 14 C3216COG2J221J Capacitor, CER, TDK 220 p, 630 V
C 15 C1206C104K5RAC Capacitor, CER, KEMET 0.1 µ, 50 V
C 16 C0805C101J1GAC Capacitor, CER, KEMET 100 p, 100 V
C 17 C0805C101J1GAC Capacitor, CER, KEMET 100 p, 100 V
C 18 C3216X7R1H334K Capacitor, CER, TDK 0.33 µ, 50 µ
16 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
Table 2. Bill of Materials (continued)
ITEM PART NUMBER DESCRIPTION VALUE
D 1 MBRB3030CTL Diode, Schottky, ON
D 2 CMPD2838-NSA Diode, Signal, Central
D 3 CMPD2838-NSA Diode, Signal, Central
D 4 CMPD2838-NSA Diode, Signal, Central
D 5 CMPD2838-NSA Diode, Signal, Central
L 1 MSS6132-103 Input Choke, Coilcraft 10 µH, 1.5 A
L 2 A9785-B Output Choke, Coilcraft 7 µH
R 1 CRCW12061R00F Resistor 1
R 2 CRCW12064990F Resistor 499
R 3 CRCW2512101J Resistor 100, 1 W
R 4 CRCW2512101J Resistor 100, 1 W
R 5 CRCW12064022F Resistor 40.2K
R 6 CRCW120610R0F Resistor 10
R 7 CRCW120610R0F Resistor 10
R 8 CRCW12061002F Resistor 10K
R 9 CRCW120623R7F Resistor 23.7
R 10 CRCW12062002F Resistor 20K
R 11 CRCW120610R0F Resistor 10
R 12 CRCW12063010F Resistor 301
R 13 CRCW120610R0F Resistor 10
R 14 CRCW12061001F Resistor 1K
TX 1 A9784-B POWER XFR, COILCRAFT
TX 2 P8208T CURRENT XFR, Pulse 100:1
U1 1 LM5030 REGULATOR, TI
U2 2 MOCD207M OPTO-COUPLER, QT OPTOELECTRONICS
U3 3 LM3411AM5-3.3 REFERENCE, TI
651-1727010 DUAL TERMINALS, MOUSER 3 per ASSY
X 1 SUD19N20-90 FET, N, 200 V, SILICONIX
X 2 SUD19N20-90 FET, N, 200 V, SILICONIX
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM5030
Q2 Gate
Q1 Gate
Q2 Drain
T1 (Pin 4)
D1 Output
L2 Output
0V
V1
V1
0V V4
V2
0V tR = 150 ns
V3
V5 V6
V7 V8
0V
V9 V10
100 mVp-p
3.3V
0V
t1 t2
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
Figure 11. Representative Waveforms
Table 3. Test Data
VIN IOUT t1 t2 Fs V1 V2 V3 V4 V5 V6 V7 V8 V9 V10
36 V 1.0 A 2.2 µS 5.3 µS 266.7 10.5 V 36 V 72 V 90 V 10 V 6 V –10 V –6 V 10 V 6 V
48 V 10 A 1.9 µS 5.5 µS 270.3 11.5 V 48 V 96 V 130 V 18 V 8 V –18 V –8 V 13 V 8 V
75 V 1.0 A 1.2 µS 6.2 µS 270.3 10.5 V 75 V 150 V 200 V 20 V 13 V –20 V –13 V 20 V 13 V
18 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LOAD CURRENT (A)
0.0
0.2
0.4
0.6
0.8
1.0
1.2
VIN = 36 V
VIN = 75 V
0 5 10
INPUT CURRENT (A)
0 2 4 6 8 10
20
30
40
50
60
70
80
90
100
EFFICIENCY (%)
LOAD CURRENT (A)
VIN = 36 V
VIN = 75 V
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
8.2.3 Application Curves
Figure 13. Efficiency vs Load Current and VIN
Figure 12. Input Current vs Load Current and VIN
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM5030
VIN
RT
SS
VCC
COMP CS
OUT2
From VIN
GND
VFB
OUT1
To Current Sense
Resistor
To Gate Drive 1
To Gate Drive 2
To Isolated Feedback
LM5030
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
www.ti.com
9 Power Supply Recommendations
The LM5030 can be used as a controller for push-pull, full bridge or half bridge power supplies. Typical
applications are for input voltages up to 100 V and output power around 30 W with switching frequency up to
1 MHz.
Care should be taken that components with the correct current rating are chosen. This includes magnetic
components, power MOSFETs and diodes, connectors and wire sizes. Input and output capacitors should have
the correct ripple current rating.
The VCC pin requires a local decoupling capacitor that is connected to GND. This capacitor ensures stability of
the internal regulator from the VIN pin. The decoupling capacitor also provides the current pulses to drive the
gates of the external MOSFETs through the driver output pins.
Place the decoupling capacitor close to the VCC and GND pins and track it directly to these pins.
10 Layout
10.1 Layout Guidelines
As in all high frequency switching power supplies, it is important to separate the high current return trace from
the low level GND signal of the controller. These signals should be connected together at a single point, usually
the negative side of the DC input filter capacitor.
Layout considerations are critical for the current sense filter. If a current sense transformer is used, both leads of
the transformer secondary should be routed to the sense filter components and to the device pins. If the current
sense circuit employs a sense resistor in the power MOSFET source, a low inductance resistor should be used
and all the low current traces should be connected in common near the device with a single connection made to
the GND pin.
The gate drive outputs of the device should have short, direct paths to the power MOSFETs in order to minimize
inductance in the gate path.
If the internal dissipation of the device produces a high junction temperature during normal operation, the use of
multiple vias under the device to a ground plane can help conduct heat away from the device.
10.2 Layout Example
Figure 14. LM5030 Board Layout
20 Submit Documentation Feedback Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: LM5030
LM5030
www.ti.com
SNVS215D –APRIL 2003–REVISED NOVEMBER 2015
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Documentation Support
11.2.1 Related Documentation
SNOA401:AN-1187 Leadless Leadframe Package (LLP)
SNVA548:Versatility of the LM5030 PWM Push-Pull Controller
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2003–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM5030
PACKAGE OPTION ADDENDUM
www.ti.com 27-Oct-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM5030MM NRND VSSOP DGS 10 1000 TBD Call TI Call TI -40 to 125 S73B
LM5030MM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S73B
LM5030MMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 S73B
LM5030SD/NOPB ACTIVE WSON DPR 10 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 5030SD
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 27-Oct-2015
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM5030MM VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM5030MM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM5030MMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM5030SD/NOPB WSON DPR 10 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 27-Oct-2015
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM5030MM VSSOP DGS 10 1000 210.0 185.0 35.0
LM5030MM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0
LM5030MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0
LM5030SD/NOPB WSON DPR 10 1000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 27-Oct-2015
Pack Materials-Page 2
MECHANICAL DATA
DPR0010A
www.ti.com
SDC10A (Rev A)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
