MGA-25203 5.1 - 5.9 GHz WiFi and WiMAX Power Amplifier (3x3mm) Data Sheet Description Features Avago Technologies MGA-25203 linear power amplifier is designed for mobile and fixed wireless data applications in the 5.1 to 5.9 GHz frequency ranges. The PA is optimized for IEEE 802.11a/n WLAN and 802.16 WiMAX applications. The PA exhibits flat gain and good match while providing linear power efficiency to meet stringent mask conditions. It utilizes Avago Technologies proprietary GaAs Enhancement-mode pHEMT technology for superior performance across voltage and temperature levels. Advanced GaAs E-pHEMT The MGA-25203 is packaged in a 3x3x1 mm size for spaceconstrained applications. Small size: 3 x 3 x 1 mm 50 all RF ports Full performance across entire 5.1-5.9GHz Operates from 4.9-5.9 GHz Integrated CMOS compatible pins for shutdown 3 to 5V supply ESD protection all ports above 1000V HBM Stable under all loads or conditions Applications -40C to +85C operation Portable WiFi and WiMAX applications Integrated DC blocking capacitors for Input and Output pins WiFi and WiMAX Access points At 5.4GHz Functional Block Diagram GND 16 VCC1 15 GND 14 Meets all IEEE 802.11n masks at 23 dBm Pout with 3.3V and 425mA VCC2 13 RFIN 1 EVM of -34dB (2.0%) at 64QAM, 54Mbps @ Pout of 23dBm GND 12 Gain of 30dB PAE of 13% BSPLY 5 BSW 6 N/C 7 1 GND 2 GND 3 BCTRL 4 N/C 8 3mm x 3mm x 1mm GND VCC2 15 14 13 17 GND 5 6 7 8 NC N/C 9 RFIN 16 NC BCTRL 4 25203 KAYYWW XXXXX VCC1 GND 10 BIAS NETWORK Device Marking Instruction BSW GND 3 RFOUT 11 GND OMN ISMN BSPLY GND 2 12 GND 11 RFOUT 10 GND 9 NC TOP VIEW "25203" = Product Code "KA" = Korea ASE "YY" = Year code indicates the year of manufacture "WW" = Workweek code indicates the workweek of manufacture "XXXXX" = Last 5 digit of assembly lot number Electrical Specifications Absolute Minimum and Maximum Ratings Table 1. Minimum and Maximum Ratings Parameter Specifications Description Pin Min. Typical Max. Unit Supply Voltage VCC1 VCC2 3 3.3 5.5 V Bias Supply BSPLY 3 3.3 5.5 V Bias Control BCTRL 1.65 2.8 5.5 V Bias ON/OFF BSW 1.65 1.8 5.5 V RF Input Power RFIN 15 V MSL MSL3 Channel Temperature 150 C 150 C Storage Temperature -65 Comments Using 64QAM Table 2. Operating Range Parameter Specifications Description Pin Min. Typical Max. Unit Supply Voltage VCC1 VCC2 3 3.3 5 V Bias Supply BSPLY 3 3.3 5 V 20 Bias Control BCTRL 2.75 2.8 mA 2.85 0.68 Bias ON/OFF BSW RF Output Power RFOUT 1.65 1.8 5.1 Thermal Resistance, ch-b Case Temperature 2.2 V 23 dBm 5.9 GHz 2 uA 23.4 -40 V uA 36 Frequency Range Comments C/W +85 C Using 64QAM Channel to board WLAN (802.11 a) Electrical Specifications All data measured on an FR4 demo board at Vcc1 = Vcc2 = 3.3V, Tc = 25C, 50 at all ports. Unless otherwise specified, all data is taken at 54Mbps 64QAM modulated signal per IEEE 802.11a with 20MHz BW at 4.9 - 5.9GHz. This module is intended for frequency band 5.1-5.9GHz. The following data from 4.9 to 5.1GHz shows that the PA is fully functional with degraded performance. Table 3. RF Electrical Characteristics Performance Parameter Min. Typical Max. Unit Input Return Loss - -8 - dB Gain Flatness - 1 - dB Over any 20MHz Gain Variation (VCC) -1 - 1 dB 3V to 5V 5.4-5.9 GHz EVM Pout, SEM Compliant 5.1-5.3 GHz 4.9-5.0 GHz - -32 -30 dB Vcc=3.3V - -36 -32 dB Vcc=5.0V +23 - - dBm IEEE 802.11a Pout=23dBm Total DC Current - 425 580 mA Gain 27 30 33 dB EVM - -30 - dB Vcc=3.3V - -32 - dB Vcc=5.0V Pout, SEM Compliant +23 - - dBm IEEE 802.11a Total DC Current - 443 - mA Pout=23dBm Gain - 27 - dB EVM - -26 - dB Vcc=3.3V - -28 - dB Vcc=5.0V - 22 - dBm IEEE 802.11a Pout=23dBm Pout, SEM Compliant P1dB Total DC Current - 468 - mA Gain - 23 - dB - 29 - dBm CW Single Tone CW Single Tone Psat - 30 - dBm Settling Time 0.2 0.5 - uS Icc leakage current - 10 40 uA 3 Comments Selected performance plots -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 5400 EVM Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=23dBm 3V0 3V3 3V6 4V2 5V0 EVM (dB) EVM (dB) 5.4 - 5.9GHz 5500 5600 5700 Frequency (MHz) 5800 5900 -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 5400 EVM Frequency Sweep (Tambient=-30C to +85C) Vcc=3.6V and Pout=23dBm -30C 25C +85C 5500 5600 5700 Frequency (MHz) 5800 5900 EVM Power Sweep (Freq=5.4 to 5.9GHz) Tambient=-30C and Vcc=3.3V 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 5. EVM Power Sweep at Vcc=3.3V and -30C over Frequency 4 5500 5600 5700 Frequency (MHz) 5800 5900 24.0 -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 EVM Power Sweep (Freq=5.4 to 5.9GHz) Tambient=25C and Vcc=3.3V 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 4. EVM Power Sweep at Vcc=3.3V and 25C over Frequency EVM (dB) EVM (dB) Figure 3. EVM Frequency Sweep at Vcc=3.6V and Pout=23dBm over Tambient -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 -30C 25C +85C Figure 2. EVM Frequency Sweep at Vcc=3.3V and Pout=23dBm over Tambient EVM (dB) EVM (dB) Figure 1. EVM Frequency Sweep at 25C and Pout=23dBm over Vcc -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 5400 EVM Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 EVM Power Sweep (Freq=5.4 to 5.9GHz) Tambient=85C and Vcc=3.3V 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 6. EVM Power Sweep at Vcc=3.3V and +85C over Frequency 24.0 Selected performance plots 5.4 - 5.9GHz (Cont.) 33.00 Gain (dB) 32.00 34 3V0 3V3 3V6 4V2 5V0 30 31.00 30.00 28.00 22 5500 5600 5700 Frequency (MHz) 5800 20 5400 5900 Gain Power Sweep (Freq=5.4 to 5.9GHz) Tambient=25C and Vcc=3.3V 32.00 30.00 30.00 28.00 24.00 22.00 20.00 19.0 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 Gain Power Sweep (Freq=5.4 to 5.9GHz) Tambient=85C and Vcc=3.3V Itotal (A) 30.00 28.00 24.00 22.00 20.00 19.0 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 11. Gain Power Sweep at Vcc=3.3V and -+85C over Frequency 5900 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 10. Gain Power Sweep at Vcc=3.3V and -30C over Frequency 32.00 26.00 5800 Gain Power Sweep (Freq=5.4 to 5.9GHz) Tambient=-30C and Vcc=3.3V 20.00 19.0 24.0 Figure 9. Gain Power Sweep at Vcc=3.3V and 25C over Frequency 34.00 26.00 22.00 23.0 5600 5700 Frequency (MHz) 28.00 24.00 21.0 22.0 Pout (dBm) 5500 34.00 32.00 26.00 -30C 25C +85C Figure 8. Gain Frequency Sweep at Vcc=3.3V and Pout=25dBm over Tambient Gain (dB) Gain (dB) 34.00 Gain (dB) 26 24 Figure 7. Gain Frequency Sweep at 25C and Pout=25dBm over Vcc 5 28 29.00 27.00 5400 Gain Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm 32 Gain (dB) 34.00 Gain Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=23dBm 24.0 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 5400 Total Current Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=23dBm 3V0 3V3 3V6 4V2 5V0 5500 5600 5700 Frequency (MHz) 5800 5900 Figure 12. Total Current Frequency Sweep at 25C and Pout=25dBm over Vcc Selected performance plots 5.4 - 5.9GHz (Cont.) 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 5400 -30C 25C +85C Itotal (A) Itotal (A) Total Current Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm 5500 5600 5700 Frequency (MHz) 5800 5900 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 19.0 Total Current Power Sweep (Freq=5.4 to 5.9GHz) Tambient=-30C and Vcc=3.3V 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 15. Total Current Power Sweep at 3.3V and -30C over Frequency 6 24.0 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 14. Total Current Power Sweep at 3.3V and 25C over Frequency Itotal (A) Itotal (A) Figure 13. Total Current Frequency Sweep at 3.3V and Pout=25dBm over Tambient 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 19.0 Total Current Power Sweep (Freq=5.4 to 5.9GHz) Tambient=25C and Vcc=3.3V 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 19.0 Total Current Power Sweep (Freq=5.4 to 5.9GHz) Tambient=85C and Vcc=3.3V 5.4GHz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 20.0 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 16. Total Current Power Sweep at 3.3V and +85C over Frequency Selected performance plots -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 4900 EVM Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=23dBm 3V0 3V3 3V6 4V2 5V0 EVM (dB) EVM (dB) 4.9 - 5.3GHz 5000 5100 5200 Frequency (MHz) 5300 5400 -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 4900 EVM Frequency Sweep (Tambient=-30C to +85C) Vcc=3.6V and Pout=23dBm -30C 25C +85C 5000 5100 5200 Frequency (MHz) 5300 5400 EVM Power Sweep (Freq=4.9 to 5.4GHz) Tambient=-30C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 Figure 21. EVM Power Sweep at Vcc=3.3V and -30C over Frequency 7 5000 5100 5200 Frequency (MHz) 5300 5400 24.0 -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 EVM Power Sweep (Freq=4.9 to 5.4GHz) Tambient=25C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 20. EVM Power Sweep at Vcc=3.3V and 25C over Frequency EVM (dB) EVM (dB) Figure 19. EVM Frequency Sweep at Vcc=3.6V and Pout=23dBm over Tambient -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 -30C 25C +85C Figure 18. EVM Frequency Sweep at Vcc=3.3V and Pout=23dBm over Tambient EVM (dB) EVM (dB) Figure 17. EVM Frequency Sweep at 25C and Pout=23dBm over Vcc -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 4900 EVM Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm -20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 19.0 EVM Power Sweep (Freq=4.9 to 5.4GHz) Tambient=85C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 Figure 22. EVM Power Sweep at Vcc=3.3V and +85C over Frequency 24.0 Selected performance plots 4.9 - 5.3GHz (Cont.) 32.00 Gain (dB) 30.00 34 3V0 3V3 3V6 4V2 5V0 32 30 Gain (dB) 34.00 Gain Frequency Sweep (Vcc=3.3V to 5.0V) Tambient=25C and Pout=23dBm 28.00 26.00 22.00 22 5100 5200 Frequency (MHz) 5300 34.00 20 4900 5400 Figure 23. Gain Frequency Sweep at 25C and Pout=23dBm over Vcc 34.00 5.2GHz 5.3GHz 5.4GHz 4.9GHz 5.0GHz 5.1GHz Gain (dB) Gain (dB) 26.00 Gain Power Sweep (Freq=4.9 to 5.4GHz) Tambient=-30C and Vcc=3.3V 26.00 24.00 22.00 22.00 20.0 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 25. Gain Power Sweep at Vcc=3.3V and 25C over Frequency 5.2GHz 5.3GHz 5.4GHz 4.9GHz 5.0GHz 5.1GHz 30.00 28.00 26.00 24.00 22.00 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 27. Gain Power Sweep at Vcc=3.3V and -+85C over Frequency 20.00 19.0 5.2GHz 5.3GHz 5.4GHz 4.9GHz 5.0GHz 5.1GHz 20.0 21.0 22.0 Pout (dBm) 23.0 Figure 26. Gain Power Sweep at Vcc=3.3V and -30C over Frequency Gain Power Sweep (Freq=4.9 to 5.4GHz) Tambient=85C and Vcc=3.3V 32.00 Gain (dB) 5400 28.00 24.00 20.00 19.0 5300 30.00 28.00 34.00 5100 5200 Frequency (MHz) 32.00 30.00 20.00 19.0 5000 Figure 24. Gain Frequency Sweep at Vcc=3.3V and Pout=23dBm over Tambient Gain Power Sweep (Freq=4.9 to 5.4GHz) Tambient=25C and Vcc=3.3V 32.00 8 26 24 5000 -30C 25C +85C 28 24.00 20.00 4900 Gain Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm 24.0 24.0 Selected performance plots 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 4900 Total Current Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=23dBm Total Current Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=23dBm 3V0 3V3 3V6 4V2 5V0 Itotal (A) Itotal (A) 4.9 - 5.3GHz (Cont.) 5000 5100 5200 Frequency (MHz) 5300 5400 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 19.0 Total Current Power Sweep (Freq=4.9 to 5.4GHz) Tambient=25C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 24.0 Itotal [A] Total Current Power Sweep (Freq=4.9 to 5.4GHz) Tambient=85C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 32. Total Current Power Sweep at 3.3V and +85C over Frequency 9 5000 5100 5200 Frequency (MHz) 5300 5400 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 19.0 Total Current Power Sweep (Freq=4.9 to 5.4GHz) Tambient=-30C and Vcc=3.3V 4.9GHz 5.0GHz 5.1GHz 20.0 5.2GHz 5.3GHz 5.4GHz 21.0 22.0 Pout (dBm) 23.0 24.0 Figure 31. Total Current Power Sweep at 3.3V and -30C over Frequency Figure 30. Total Current Power Sweep at 3.3V and 25C over Frequency 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 19.0 -30C 25C +85C Figure 29. Total Current Frequency Sweep at 3.3V and Pout=23dBm over Tambient Itotal (A) Itotal (A) Figure 28. Total Current Frequency Sweep at 25C and Pout=23dBm over Vcc 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 4900 Evaluation Board Description Table 4. Evaluation Board Pin Description Top Pin No. Function Bottom Pin No. Function Recommended turn on sequence 1 VCC2 2 VCC2_S Apply VCC1 and VCC2 3.3V 3 B_SPLY 4 GND Apply BSPLY 3.3V 5 VCC1 6 GND Apply BCTRL 2.8V 7 NC 8 GND Apply BSW 1.8V 9 NC 10 GND Apply RF In, not to exceed 15dBm 11 NC 12 GND 13 NC 14 B_SW 15 B_CTRL 16 GND 17 NC 18 GND 19 NC 20 GND Table 5. Typical Test Conditions Pin HPM Description VCC1,2 3.3V Supply Voltage B_SPLY 3.3V Bias Voltage B_CTRL 2.8V Bias Control B_SW 1.8V PA Enable Notes: VCC1, VCC2 and B_SPLY can be tied together to reduce supply voltages, but B_CTRL needs to be a regulated voltage which is optimized for 2.8V. Demoboard Top Pins 10 Demoboard Bottom Pins Application Circuit MGA-25203 Vdd1 Vdd2 47uF 10uF 10uF 0.1uF 100pF VCC2 VCC2 1313 GND GND1414 RF In VCC1 VCC1 1515 GND GND1616 100pF 11 RF RF In In GND GND1212 22 GND GND RFRF OutOut 11 11 33 GND GND GND GND 1010 RF Out BCTRL 100pF NCNC9 9 88NC NC 100pF 77PAMOD NC 100pF 66BSW BSW 0.1uF 55BSPLY BSPLY 44 BCTRL BCTRL 100pF BSPLY BSW Using 3.3V or 5V Supply and tying Vcc1, Vcc2, BSPLY and BCTRL Vbat R1 R2 Vcc1 Vcc2 BSPLY 3.3V Example : VBCTRL = 2.8V = BCTRL Given : R2 R1 + R2 40K R1 + 40K *VBATT *3.3V Notes: BCTRL regulates the device current, thus R1 and R2 should have good tolerance rating. If available, a voltage regulator is the preferred method of bias. In this example we set R2 at 40KOhm and solve for R1 with simple voltage divider equation. Note this method will cause some leakage current through R2. 5.0V Example : VBCTRL = 2.8V VBAT = 3.3V R2 = 40K R1 =? VBCTRL = 2.0V = Given : R2 R1 + R2 20K R1 + 20K R1 = 7K R1 = 30K R2 = 40K R2 = 20K 11 *VBATT *5.0V VBCTRL = 2.0V VBAT = 5.0V R2 = 20K R1 =? Land Pattern 4 5 0.300.10 0.100.10 Top view through package Figure 34. Package dimensions VCC2 GND VCC1 GND 3.000.10 1.600.10 4 5 6 7 8 11 RFOUT 10 GND 9 NC Top view through package Figure 35. Recommended mask opening 12 0.400.10 0.550.10 BCTRL GND 0.100.10 3 12 0.650.10 GND 17 GND NC 2 NC GND 13 BSW 1 14 BSPLY 3.000.10 RFIN 15 7 VCC2 RFOUT 10 GND 9 NC 8 0.300.10 Top view through package Figure 33. Recommended footprint 16 6 11 Notes: 1. All units are in millimeters 2. Package is symmetrical 0.600.10 BCTRL GND 0.200.10 3 17 GND 12 0.300.10 NC GND 13 NC 9 2 14 NC 8 GND GND 15 BSW 7 10 1 BSPLY 6 RFOUT RFIN 0.150.10 5 11 3.000.10 1.500.10 4 GND 0.600.10 BCTRL 12 0.200.10 3 16 0.550.10 GND 17 GND NC 2 NC GND 13 BSW 1 14 1.500.10 BSPLY 3.000.10 1.500.10 RFIN 15 GND GND 1.500.10 16 VCC1 3.000.10 VCC2 GND VCC1 GND 3.000.10 Ordering Information Part Number No. of Devices Container MGA-25203-BLKG 100 7" Reel MGA-25203-TR1G 3000 13" Reel Package Dimensions 1.00 0.10 3.00 0.10 Pin 1 Dot By Marking 25003 KAYYWW XXXX 3.00 0.10 0.64 TYPICAL TOP VIEW SIDE VIEW Note 1. All dimensions are in millimeters. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold flash and metal burr. Device Orientation REEL USER FEED DIRECTION CARRIER TAPE USER FEED DIRECTION 13 AVAGO 25003 YYWW XXXX AVAGO 25003 YYWW XXXX TOP VIEW COVER TAPE AVAGO 25003 YYWW XXXX END VIEW Tape and Reel Information W3 W2 B 12mm A 330 +2.0 2.0 B 1.5min. C 13.0 +0.5 0.2 D 20.2min. N 100 +3.0 0.0 W1 12.4 +3.0 0.0 W2 16.4 +2.0 2.0 W3 13.65 +1.75 0.75 N C A Size 120 o1 3 .0 + -0 0.50 .20 10.50 W1 2.000.05 4.000.10 + -0 0.10 .00 3.400.10 1.700.10 14 8.000.10 o1.50MIN 12.000.30 .50 1.750.10 o1 5.500.05 0.300.05 2.00 Handling and Storage tp TP CRITICAL ZONE TL TO TP RAMP UP TEMPERATURE TL tL Tsmax Tsmin ts PREHEAT RAMP DOWN 25 t 25C TO PEAK TIME Typical SMT Reflow Profile for Maximum Temperature = 260+0/-5C Profile Feature Sn-Pb Solder Pb-Free Solder Average ramp-up rate (TL to TP) 3C/sec max 3C/sec max Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (mon to max) (ts) 100C 150C 60-120 sec 100C 150C 60-180 sec Tsmax to TL - Ramp-up Rate Time maintained above: - Temperature (TL) - Time (TL) 3C/sec max 183C 60-150 sec 217C 60-150 sec Peak temperature (Tp) 240 +0/-5C 260 +0/-5C Time within 5C of actual Peak Temperature (tp) 10-30 sec 10-30 sec Ramp-down Rate 6C/sec max 6C/sec max Time 25C to Peak Temperature 6 min max 8 min max For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2012 Avago Technologies. All rights reserved. AV02-1961EN - September 14, 2012