Semiconductor Components Industries, LLC, 2002
April, 2002 – Rev. 0 1Publication Order Number:
MMBTA06WT1/D
MMBTA06WT1
Driver Transistor
NPN Silicon
Moisture Sensitivity Level: 1
ESD Rating: Human Body Model – 4 kV
ESD Rating: Machine Model – 400 V
MAXIMUM RATINGS
Rating Symbol Value Unit
Collector–Emitter Voltage VCEO 80 Vdc
Collector–Base Voltage VCBO 80 Vdc
Emitter–Base Voltage VEBO 4.0 Vdc
Collector Current – Continuous IC500 mAdc
THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Total Device Dissipation FR–5 Board
TA = 25°CPD150 mW
Thermal Resistance,
Junction to Ambient RJA 833 °C/W
Junction and Storage Temperature TJ, Tstg –55 to +150 °C
Device Package Shipping
ORDERING INFORMATION
MMBTA06WT1 SC–70
SC–70
CASE 419
STYLE 3
3000/Tape & Reel
2
3
1
MARKING DIAGRAM
GM D
GM = Specific Device Code
D = Date Code
COLLECTOR
3
1
BASE
2
EMITTER
http://onsemi.com
MMBTA06WT1
http://onsemi.com
2
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic Symbol Min Max Unit
OFF CHARACTERISTICS
Collector–Emitter Breakdown V oltage (Note 1)
(IC = 1.0 mAdc, IB = 0) V(BR)CEO 80 Vdc
Emitter–Base Breakdown Voltage
(IE = 100 Adc, IC = 0) V(BR)EBO 4.0 Vdc
Collector Cutoff Current
(VCE = 60 Vdc, IB = 0) ICES 0.1 Adc
Collector Cutoff Current
(VCB = 80 Vdc, IE = 0) ICBO 0.1 Adc
ON CHARACTERISTICS
DC Current Gain
(IC = 10 mAdc, VCE = 1.0 Vdc)
(IC = 100 mAdc, V CE = 1.0 Vdc)
hFE 100
100
CollectorEmitter Saturation Voltage
(IC = 100 mAdc, I B = 10 mAdc) VCE(sat) 0.25 Vdc
Base– E m itte r On Voltage
(IC = 100 mAdc, V CE = 1.0 Vdc) VBE(on) 1.2 Vdc
SMALL–SIGNAL CHARACTERISTICS
Current–Gain – Bandwidth Product (Note 2)
(IC = 10 mA, VCE = 2.0 V, f = 100 MHz) fT100 MHz
1. Pulse Test: Pulse Width 300 s, Duty Cycle 2.0%.
2. fT is defined as the frequency at which |hfe| extrapolates to unity.
Figure 1. Switching Time Test Circuits
OUTPUT
TURN-ON TIME
-1.0 V VCC
+40 V
RL
* CS 6.0 pF
RB
100
100
Vin
5.0 F
tr = 3.0 ns
0
+10 V
5.0 s
OUTPUT
TURN-OFF TIME
+VBB VCC
+40 V
RL
* CS 6.0 pF
RB
100
100
Vin
5.0 F
tr = 3.0 ns
5.0 s
*Total Shunt Capacitance of Test Jig and Connectors
For PNP Test Circuits, Reverse All Voltage Polarities
MMBTA06WT1
http://onsemi.com
3
Figure 2. Current–Gain — Bandwidth Product Figure 3. Capacitance
Figure 4. Switching T ime
100 2002.0
IC, COLLECTOR CURRENT (mA)
300
200
100
70
50
30
10 1000.1
VR, REVERSE VOLTAGE (VOLTS)
80
60
40
20
10
8.0
20
VCE = 2.0 V
TJ = 25°C
TJ = 25°C
3.0 5.0 7.0 10 20 30 50 70
fT, CURRENT-GAIN - BANDWIDTH PRODUCT (MHz
)
501.0 2.0 5.00.2 0.5
6.0
4.0
Cibo
Cobo
2010
IC, COLLECTOR CURRENT (mA)
200
100
50
20
10 100
t, TIME (ns)
50 200 500
1.0 k
500
VCC = 40 V
IC/IB = 10
IB1 = IB2
TJ = 25°C
ts
tf
tr
5.0 7.0
30
70
300
700
30 70
td @ VBE(off) = 0.5 V
C, CAPACITANCE (pF)
300
Figure 5. Active–Region Safe Operating Area
101.0
VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS)
500
200
100
50
20
10
30
IC, COLLECTOR CURRENT (mA)
2.0 5.0 50
1.0 k
1.0 ms
1.0 s
TA = 25°C
CURRENT LIMIT
THERMAL LIMIT
SECOND BREAKDOWN LIMIT
10070203.0 7.0
100 s
TC = 25°C
700
300
30
70
Figure 6. DC Current Gain
2.0 5000.5
IC, COLLECTOR CURRENT (mA)
400
200
100
80
60
40
10
, DC CURRENT GAIN
TJ = 125°C
1.0 3.0 5.0
VCE = 1.0 V
20 10030 50 200 300
hFE
25°C
-55°C
Figure 7. “ON” Voltages
10 5001.0
IC, COLLECTOR CURRENT (mA)
1.0
0.8
0.6
0.4
0.2
0
100
TJ = 25°C
V, VOLTAGE (VOLTS)
VBE(sat) @ IC/IB = 10
VCE(sat) @ IC/IB = 10
VBE(on) @ VCE = 1.0 V
0.5 2.0 5.0 20020 50
MMBTA06WT1
http://onsemi.com
4
Figure 8. Collector Saturation Region Figure 9. Base–Emitter Temperature
Coefficient
100 5000.5
IC, COLLECTOR CURRENT (mA)
-0.8
-1.2
-1.6
-2.0
-2.4
-2.8
0.1 100.05
IB, BASE CURRENT (mA)
1.0
0.8
0.6
0.4
0.2
0
1.0
TJ = 25°C
RVB , TEMPERATURE COEFFICIENT (mV/ C)
10
RVB for VBE
°
50
IC =
100 mA
IC =
50 mA
IC =
250 mA
IC =
500 mA
IC =
10 mA
, COLLECTOR-EMITTER VOLTAGE (VOLTS)VCE
1.0 2.0 5.0 20 50 200202.0 5.00.2 0.5
MMBTA06WT1
http://onsemi.com
5
PD = TJ(max) – TA
RθJA
PD = 150°C – 25°C
833°C/W = 150 milliwatts
The soldering temperature and time should not
exceed 260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5°C or less.
After soldering has been completed, the device
should be allowed to cool naturally for at least three
minutes. Gradual cooling should be used as the use of
forced cooling will increase the temperature gradient
and result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied dur-
ing cooling
* Soldering a device without preheating can cause exces-
sive thermal shock and stress which can result in damage
to the device.
INFORMATION FOR USING THE SC–70/SOT–323 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the to-
tal design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
SC–70/SOT–323 POWER DISSIPATION
The power dissipation of the SC–70/SOT–323 is a func-
tion of the pad size. This can vary from the minimum pad
size for soldering to the pad size given for maximum pow-
er dissipation. Power dissipation for a surface mount de-
vice is determined by TJ(max), the maximum rated junction
temperature of the die, RθJA, the thermal resistance from
the device junction to ambient; and the operating tempera-
ture, TA. Using the values provided on the data sheet, PD
can be calculated as follows.
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25°C,
one can calculate the power dissipation of the device
which in this case is 150 milliwatts.
The 833°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve
a power dissipation of 150 milliwatts. Another alternative
would be to use a ceramic substrate or an aluminum core
board such as Thermal Clad. Using a board material
such as Thermal Clad, a higher power dissipation can be
achieved using the same footprint.
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to mini-
mize the thermal stress to which the devices are subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference should be a maximum of 10°C.
mm
inches
0.035
0.9
0.075
0.7
1.9
0.028
0.65
0.025
0.65
0.025
MMBTA06WT1
http://onsemi.com
6
PACKAGE DIMENSIONS
CN
AL
D
G
SB
H
J
K
3
12
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.071 0.087 1.80 2.20
B0.045 0.053 1.15 1.35
C0.032 0.040 0.80 1.00
D0.012 0.016 0.30 0.40
G0.047 0.055 1.20 1.40
H0.000 0.004 0.00 0.10
J0.004 0.010 0.10 0.25
K0.017 REF 0.425 REF
L0.026 BSC 0.650 BSC
N0.028 REF 0.700 REF
S0.079 0.095 2.00 2.40
0.05 (0.002) STYLE 3:
PIN 1. BASE
2. EMITTER
3. COLLECTOR
SC–70/SOT–323
CASE 419–04
ISSUE L
MMBTA06WT1
http://onsemi.com
7
Notes
MMBTA06WT1
http://onsemi.com
8
ON Semiconductor is a trademark and is a registered trademark of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right
to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products
for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation special, consequential or incidental damages. “T ypical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must
be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur . Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: r14525@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
MMBTA06WT1/D
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada