M24C16, M24C08 M24C04, M24C02, M24C01 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit Serial IC Bus EEPROM FEATURES SUMMARY Two-Wire IC Serial Interface Supports 400kHz Protocol Single Supply Voltage: - 2.5 to 5.5V for M24Cxx-W - 1.8 to 5.5V for M24Cxx-R Write Control Input BYTE and PAGE WRITE (up to 16 Bytes) RANDOM and SEQUENTIAL READ Modes Self-Timed Programming Cycle Automatic Address Incrementing Enhanced ESD/Latch-Up Protection More than 1 Million Erase/Write Cycles More than 40-Year Data Retention Packages - ECOPACK(R) (RoHS compliant) Figure 1. Packages PDIP8 (BN) SO8 (MN) 150 mil width Table 1. Product List Reference Part Number M24C16-W M24C16 M24C16-R M24C08-W TSSOP8 (DW) 169 mil width M24C08 M24C08-R M24C04-W M24C04 M24C04-R M24C02-W M24C02 TSSOP8 (DS) 3x3mm body size (MSOP) M24C02-R M24C01-W M24C01 M24C01-R January 2006 UFDFPN8 (MB) 2x3mm (MLP) 1/28 M24C16, M24C08, M24C04, M24C02, M24C01 TABLE OF CONTENTS FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table 1. Product List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 1. Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table 2. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 3. 8-Pin Package Connections (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SIGNAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Serial Clock (SCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Serial Data (SDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chip Enable (E0, E1, E2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 4. Device Select Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Write Control (WC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating supply voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Internal Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power-down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 5. Maximum RP Value versus Bus Parasitic Capacitance (C) for an IC Bus . . . . . . . . . . . 6 Figure 6. IC Bus Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table 3. Device Select Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DEVICE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Start Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Stop Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Acknowledge Bit (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Memory Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 4. Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 7. Write Mode Sequences with WC=1 (data write inhibited) . . . . . . . . . . . . . . . . . . . . . . . . . 9 Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 8. Write Mode Sequences with WC=0 (data write enabled) . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 9. Write Cycle Polling Flowchart using ACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Minimizing System Delays by Polling On ACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 10.Read Mode Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Read Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Random Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Sequential Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Acknowledge in Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2/28 M24C16, M24C08, M24C04, M24C02, M24C01 INITIAL DELIVERY STATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 5. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DC and AC PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 6. Operating Conditions (M24Cxx-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 7. Operating Conditions (M24Cxx-R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 8. DC Characteristics (M24Cxx-W, Device Grade 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 9. DC Characteristics (M24Cxx-W, Device Grade 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 10. DC Characteristics (M24Cxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 11. AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 11.AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 12. Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 13. AC Characteristics (M24Cxx-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 14. AC Characteristics (M24Cxx-R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 12.AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 13.PDIP8 - 8 pin Plastic DIP, 0.25mm lead frame, Package Outline . . . . . . . . . . . . . . . . . 21 Table 15. PDIP8 - 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data . . . . . . . . . . 21 Figure 14.SO8 narrow - 8 lead Plastic Small Outline, 150 mils body width, Package Outline . . . . 22 Table 16. SO8 narrow - 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 15.UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2x3mm, Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 17. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2x3mm, Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 16.TSSOP8 - 8 lead Thin Shrink Small Outline, Package Outline . . . . . . . . . . . . . . . . . . . 24 Table 18. TSSOP8 - 8 lead Thin Shrink Small Outline, Package Mechanical Data . . . . . . . . . . . . 24 Figure 17.TSSOP8 3x3mm - 8 lead Thin Shrink Small Outline, 3x3mm body size, Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table 19. TSSOP8 3x3mm - 8 lead Thin Shrink Small Outline, 3x3mm body size, Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 20. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 21. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3/28 M24C16, M24C08, M24C04, M24C02, M24C01 SUMMARY DESCRIPTION These IC-compatible electrically erasable programmable memory (EEPROM) devices are organized as 2048/1024/512/256/128 x 8 (M24C16, M24C08, M24C04, M24C02 and M24C01). In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. ECOPACK(R) packages are Lead-free and RoHS compliant. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 2. Logic Diagram VCC 3 E0-E2 SCL SDA IC uses a two-wire serial interface, comprising a bi-directional data line and a clock line. The devices carry a built-in 4-bit Device Type Identifier code (1010) in accordance with the IC bus definition. The device behaves as a slave in the IC protocol, with all memory operations synchronized by the serial clock. Read and Write operations are initiated by a Start condition, generated by the bus master. The Start condition is followed by a Device Select Code and Read/Write bit (RW) (as described in Table 3.), terminated by an acknowledge bit. When writing data to the memory, the device inserts an acknowledge bit during the 9th bit time, following the bus master's 8-bit transmission. When data is read by the bus master, the bus master acknowledges the receipt of the data byte in the same way. Data transfers are terminated by a Stop condition after an Ack for Write, and after a NoAck for Read. Table 2. Signal Names M24Cxx WC VSS AI02033 E0, E1, E2 Chip Enable SDA Serial Data SCL Serial Clock WC Write Control VCC Supply Voltage VSS Ground Figure 3. 8-Pin Package Connections (Top View) M24Cxx 16Kb /8Kb /4Kb /2Kb /1Kb NC / NC / NC / E0 / E0 NC / NC / E1 / E1 / E1 NC / E2 / E2 / E2 / E2 VSS 1 2 3 4 8 7 6 5 VCC WC SCL SDA AI02034E Note: 1. NC = Not Connected 2. See PACKAGE MECHANICAL section for package dimensions, and how to identify pin-1. 4/28 M24C16, M24C08, M24C04, M24C02, M24C01 SIGNAL DESCRIPTION Serial Clock (SCL) This input signal is used to strobe all data in and out of the device. In applications where this signal is used by slave devices to synchronize the bus to a slower clock, the bus master must have an open drain output, and a pull-up resistor can be connected from Serial Clock (SCL) to VCC. (Figure 5. indicates how the value of the pull-up resistor can be calculated). In most applications, though, this method of synchronization is not employed, and so the pull-up resistor is not necessary, provided that the bus master has a push-pull (rather than open drain) output. Serial Data (SDA) This bi-directional signal is used to transfer data in or out of the device. It is an open drain output that may be wire-OR'ed with other open drain or open collector signals on the bus. A pull up resistor must be connected from Serial Data (SDA) to VCC. (Figure 5. indicates how the value of the pull-up resistor can be calculated). Chip Enable (E0, E1, E2) These input signals are used to set the value that is to be looked for on the three least significant bits (b3, b2, b1) of the 7-bit Device Select Code. These inputs must be tied to VCC or VSS, to establish the Device Select Code as shown in Figure 4. Figure 4. Device Select Code VCC VCC M24Cxx M24Cxx Ei Ei VSS VSS Ai11650 Write Control (WC). This input signal is useful for protecting the entire contents of the memory from inadvertent write operations. Write operations are disabled to the entire memory array when Write Control (WC) is driven High. When unconnected, the signal is internally read as VIL, and Write operations are allowed. When Write Control (WC) is driven High, Device Select and Address bytes are acknowledged, Data bytes are not acknowledged. Supply voltage (VCC) Operating supply voltage VCC. Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage must be applied: this voltage must be a DC voltage within the specified [VCC(min), VCC(max)] range, as defined in Table 6. and Table 7. In order to secure a stable DC supply voltage, it is recommended to decouple the VCC line with a suitable capacitor (usually of the order of 10nF to 100nF) close to the VCC/VSS package pins. The VCC voltage must remain stable and valid until the end of the transmission of the instruction and, for a Write instruction, until the completion of the internal write cycle (tW). Internal Device Reset. In order to prevent inadvertent Write operations during Power-up, a Power On Reset (POR) circuit is included. At Power-up (continuous rise of VCC), the device does not respond to any instruction until VCC has reached the Power On Reset threshold voltage (this threshold is lower than the minimum VCC operating voltage defined in Table 6. and Table 7.). When VCC has passed the POR threshold, the device is reset and in the Standby Power mode Power-down. At Power-down (where VCC decreases continuously), as soon as VCC drops from the operating voltage range below the Power On Reset threshold voltage, the device stops responding to any instruction sent to it. During Power-down, the device must be deselected and in the Standby Power mode (that is there should be no internal Write cycle in progress). 5/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 5. Maximum RP Value versus Bus Parasitic Capacitance (C) for an IC Bus VCC Maximum RP value (k) 20 16 RP 12 RP SDA MASTER 8 fc = 100kHz 4 C SCL fc = 400kHz C 0 10 100 1000 C (pF) AI01665b Figure 6. IC Bus Protocol SCL SDA SDA Input START Condition SCL 1 SDA MSB 2 SDA Change STOP Condition 3 7 8 9 ACK START Condition SCL 1 SDA MSB 2 3 7 8 9 ACK STOP Condition AI00792B 6/28 M24C16, M24C08, M24C04, M24C02, M24C01 Table 3. Device Select Code Device Type Identifier1 Chip Enable2,3 RW b7 b6 b5 b4 b3 b2 b1 b0 M24C01 Select Code 1 0 1 0 E2 E1 E0 RW M24C02 Select Code 1 0 1 0 E2 E1 E0 RW M24C04 Select Code 1 0 1 0 E2 E1 A8 RW M24C08 Select Code 1 0 1 0 E2 A9 A8 RW M24C16 Select Code 1 0 1 0 A10 A9 A8 RW Note: 1. The most significant bit, b7, is sent first. 2. E0, E1 and E2 are compared against the respective external pins on the memory device. 3. A10, A9 and A8 represent most significant bits of the address. 7/28 M24C16, M24C08, M24C04, M24C02, M24C01 DEVICE OPERATION The device supports the IC protocol. This is summarized in Figure 6.. Any device that sends data on to the bus is defined to be a transmitter, and any device that reads the data to be a receiver. The device that controls the data transfer is known as the bus master, and the other as the slave device. A data transfer can only be initiated by the bus master, which will also provide the serial clock for synchronization. The M24Cxx device is always a slave in all communication. Start Condition Start is identified by a falling edge of Serial Data (SDA) while Serial Clock (SCL) is stable in the High state. A Start condition must precede any data transfer command. The device continuously monitors (except during a Write cycle) Serial Data (SDA) and Serial Clock (SCL) for a Start condition, and will not respond unless one is given. Stop Condition Stop is identified by a rising edge of Serial Data (SDA) while Serial Clock (SCL) is stable and driven High. A Stop condition terminates communication between the device and the bus master. A Read command that is followed by NoAck can be followed by a Stop condition to force the device into the Stand-by mode. A Stop condition at the end of a Write command triggers the internal Write cycle. Acknowledge Bit (ACK) The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter, whether it be bus master or slave device, releases Serial Data (SDA) after sending eight bits of data. During the 9th clock pulse period, the receiver pulls Serial Data (SDA) Low to acknowledge the receipt of the eight data bits. Data Input During data input, the device samples Serial Data (SDA) on the rising edge of Serial Clock (SCL). 8/28 For correct device operation, Serial Data (SDA) must be stable during the rising edge of Serial Clock (SCL), and the Serial Data (SDA) signal must change only when Serial Clock (SCL) is driven Low. Memory Addressing To start communication between the bus master and the slave device, the bus master must initiate a Start condition. Following this, the bus master sends the Device Select Code, shown in Table 3. (on Serial Data (SDA), most significant bit first). The Device Select Code consists of a 4-bit Device Type Identifier, and a 3-bit Chip Enable "Address" (E2, E1, E0). To address the memory array, the 4bit Device Type Identifier is 1010b. Each device is given a unique 3-bit code on the Chip Enable (E0, E1, E2) inputs. When the Device Select Code is received, the device only responds if the Chip Enable Address is the same as the value on the Chip Enable (E0, E1, E2) inputs. However, those devices with larger memory capacities (the M24C16, M24C08 and M24C04) need more address bits. E0 is not available for use on devices that need to use address line A8; E1 is not available for devices that need to use address line A9, and E2 is not available for devices that need to use address line A10 (see Figure 3. and Table 3. for details). Using the E0, E1 and E2 inputs, up to eight M24C02 (or M24C01), four M24C04, two M24C08 or one M24C16 devices can be connected to one IC bus. In each case, and in the hybrid cases, this gives a total memory capacity of 16 Kbits, 2 KBytes (except where M24C01 devices are used). The 8th bit is the Read/Write bit (RW). This bit is set to 1 for Read and 0 for Write operations. If a match occurs on the Device Select code, the corresponding device gives an acknowledgment on Serial Data (SDA) during the 9th bit time. If the device does not match the Device Select code, it deselects itself from the bus, and goes into Standby mode. M24C16, M24C08, M24C04, M24C02, M24C01 Table 4. Operating Modes Mode RW bit WC (1) Bytes 1 X 1 0 X Current Address Read Initial Sequence START, Device Select, RW = 1 START, Device Select, RW = 0, Address Random Address Read 1 1 X reSTART, Device Select, RW = 1 Sequential Read 1 X 1 Byte Write 0 VIL 1 START, Device Select, RW = 0 Page Write 0 VIL 16 START, Device Select, RW = 0 Similar to Current or Random Address Read Note: 1. X = VIH or VIL. Figure 7. Write Mode Sequences with WC=1 (data write inhibited) WC ACK BYTE ADDR NO ACK DATA IN STOP DEV SEL START Byte Write ACK R/W WC ACK DEV SEL START Page Write ACK BYTE ADDR NO ACK DATA IN 1 NO ACK DATA IN 2 DATA IN 3 R/W WC (cont'd) NO ACK DATA IN N STOP Page Write (cont'd) NO ACK AI02803C 9/28 M24C16, M24C08, M24C04, M24C02, M24C01 Write Operations Page Write Following a Start condition the bus master sends a Device Select Code with the Read/Write bit (RW) reset to 0. The device acknowledges this, as shown in Figure 8., and waits for an address byte. The device responds to the address byte with an acknowledge bit, and then waits for the data byte. When the bus master generates a Stop condition immediately after the Ack bit (in the "10th bit" time slot), either at the end of a Byte Write or a Page Write, the internal Write cycle is triggered. A Stop condition at any other time slot does not trigger the internal Write cycle. During the internal Write cycle, Serial Data (SDA) and Serial Clock (SCL) are ignored, and the device does not respond to any requests. The Page Write mode allows up to 16 bytes to be written in a single Write cycle, provided that they are all located in the same page in the memory: that is, the most significant memory address bits are the same. If more bytes are sent than will fit up to the end of the page, a condition known as `rollover' occurs. This should be avoided, as data starts to become overwritten in an implementation dependent way. The bus master sends from 1 to 16 bytes of data, each of which is acknowledged by the device if Write Control (WC) is Low. If the addressed location is Write-protected, by Write Control (WC) being driven High (during the period from the Start condition until the end of the address byte), the device replies to the data bytes with NoAck, as shown in Figure 7., and the locations are not modified. After each byte is transferred, the internal byte address counter (the 4 least significant address bits only) is incremented. The transfer is terminated by the bus master generating a Stop condition. Byte Write After the Device Select code and the address byte, the bus master sends one data byte. If the addressed location is Write-protected, by Write Control (WC) being driven High (during the period from the Start condition until the end of the address byte), the device replies to the data byte with NoAck, as shown in Figure 7., and the location is not modified. If, instead, the addressed location is not Write-protected, the device replies with Ack. The bus master terminates the transfer by generating a Stop condition, as shown in Figure 8.. 10/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 8. Write Mode Sequences with WC=0 (data write enabled) WC ACK BYTE ADDR ACK DATA IN STOP DEV SEL START BYTE WRITE ACK R/W WC ACK DEV SEL START PAGE WRITE ACK BYTE ADDR ACK DATA IN 1 ACK DATA IN 2 DATA IN 3 R/W WC (cont'd) ACK DATA IN N STOP PAGE WRITE (cont'd) ACK AI02804B 11/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 9. Write Cycle Polling Flowchart using ACK WRITE Cycle in Progress START Condition DEVICE SELECT with RW = 0 NO ACK Returned YES First byte of instruction with RW = 0 already decoded by the device NO Next Operation is Addressing the Memory YES Send Address and Receive ACK ReSTART NO STOP YES DATA for the WRITE Operation DEVICE SELECT with RW = 1 Continue the WRITE Operation Continue the Random READ Operation Minimizing System Delays by Polling On ACK During the internal Write cycle, the device disconnects itself from the bus, and writes a copy of the data from its internal latches to the memory cells. The maximum Write time (tw) is shown in Table 13. and Table 14., but the typical time is shorter. To make use of this, a polling sequence can be used by the bus master. The sequence, as shown in Figure 9., is: 12/28 START Condition - - - AI01847C Initial condition: a Write cycle is in progress. Step 1: the bus master issues a Start condition followed by a Device Select Code (the first byte of the new instruction). Step 2: if the device is busy with the internal Write cycle, no Ack will be returned and the bus master goes back to Step 1. If the device has terminated the internal Write cycle, it responds with an Ack, indicating that the device is ready to receive the second part of the instruction (the first byte of this instruction having been sent during Step 1). M24C16, M24C08, M24C04, M24C02, M24C01 Figure 10. Read Mode Sequences ACK DATA OUT STOP START DEV SEL NO ACK R/W ACK START DEV SEL * ACK BYTE ADDR R/W ACK START DEV SEL DATA OUT R/W ACK ACK NO ACK DATA OUT N DATA OUT 1 R/W ACK START DEV SEL * ACK BYTE ADDR R/W ACK ACK DEV SEL * START SEQUENTIAL RANDOM READ DEV SEL * NO ACK STOP SEQUENTIAL CURRENT READ ACK START RANDOM ADDRESS READ STOP CURRENT ADDRESS READ ACK DATA OUT 1 R/W NO ACK STOP DATA OUT N AI01942 Note: The seven most significant bits of the Device Select Code of a Random Read (in the 1st and 3rd bytes) must be identical. Read Operations Read operations are performed independently of the state of the Write Control (WC) signal. The device has an internal address counter which is incremented each time a byte is read. Random Address Read A dummy Write is first performed to load the address into this address counter (as shown in Figure 10.) but without sending a Stop condition. Then, the bus master sends another Start condition, and repeats the Device Select Code, with the Read/Write bit (RW) set to 1. The device acknowl- edges this, and outputs the contents of the addressed byte. The bus master must not acknowledge the byte, and terminates the transfer with a Stop condition. Current Address Read For the Current Address Read operation, following a Start condition, the bus master only sends a Device Select Code with the Read/Write bit (RW) set to 1. The device acknowledges this, and outputs the byte addressed by the internal address counter. The counter is then incremented. The bus master terminates the transfer with a Stop condi- 13/28 M24C16, M24C08, M24C04, M24C02, M24C01 tion, as shown in Figure 10., without acknowledging the byte. and the device continues to output data from memory address 00h. Sequential Read Acknowledge in Read Mode This operation can be used after a Current Address Read or a Random Address Read. The bus master does acknowledge the data byte output, and sends additional clock pulses so that the device continues to output the next byte in sequence. To terminate the stream of bytes, the bus master must not acknowledge the last byte, and must generate a Stop condition, as shown in Figure 10.. The output data comes from consecutive addresses, with the internal address counter automatically incremented after each byte output. After the last memory address, the address counter `rolls-over', For all Read commands, the device waits, after each byte read, for an acknowledgment during the 9th bit time. If the bus master does not drive Serial Data (SDA) Low during this time, the device terminates the data transfer and switches to its Standby mode. 14/28 INITIAL DELIVERY STATE The device is delivered with all bits in the memory array set to 1 (each byte contains FFh). M24C16, M24C08, M24C04, M24C02, M24C01 MAXIMUM RATING Stressing the device outside the ratings listed in Table 5. may cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions outside those indicated in the Operating sections of this specification, is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 5. Absolute Maximum Ratings Symbol Min. Max. Unit Ambient Operating Temperature -40 130 C TSTG Storage Temperature -65 150 C TLEAD PDIP-Specific Lead Temperature during Soldering 260(1) C TA Parameter VIO Input or Output range -0.50 6.5 V VCC Supply Voltage -0.50 6.5 V VESD Electrostatic Discharge Voltage (Human Body model) (2) -4000 4000 V Note: 1. TLEAD max must not be applied for more than 10s. 2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114A, C1=100pF, R1=1500, R2=500). 15/28 M24C16, M24C08, M24C04, M24C02, M24C01 DC AND AC PARAMETERS This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC Characteristic tables that follow are derived from tests performed under the Measure- ment Conditions summarized in the relevant tables. Designers should check that the operating conditions in their circuit match the measurement conditions when relying on the quoted parameters. Table 6. Operating Conditions (M24Cxx-W) Symbol VCC Parameter Min. Max. Unit Supply Voltage 2.5 5.5 V Ambient Operating Temperature (Device Grade 6) -40 85 C Ambient Operating Temperature (Device Grade 3) -40 125 C Min. Max. Unit Supply Voltage 1.8 5.5 V Ambient Operating Temperature -40 85 C TA Table 7. Operating Conditions (M24Cxx-R) Symbol VCC TA Parameter Table 8. DC Characteristics (M24Cxx-W, Device Grade 6) Symbol Parameter ILI Input Leakage Current (SCL, SDA, E0, E1,and E2) ILO Output Leakage Current ICC Supply Current Test Condition (in addition to those in Table 6.) Min. Max. Unit VIN = VSS or VCC 2 A VOUT = VSS or VCC, SDA in Hi-Z 2 A VCC=5V, fc=400kHz (rise/fall time < 30ns) 2 mA VCC =2.5V, fc=400kHz (rise/fall time < 30ns) 1 mA VIN = VSS or VCC, for 2.5V < VCC = < 5.5V 1 A ICC1 Stand-by Supply Current VIL Input Low Voltage (1) -0.45 0.3VCC V VIH Input High Voltage (1) 0.7VCC VCC+1 V VOL Output Low Voltage 0.4 V IOL = 2.1mA when VCC = 2.5V or IOL = 3mA when VCC = 5.5V Note: 1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kOhm. 16/28 M24C16, M24C08, M24C04, M24C02, M24C01 Table 9. DC Characteristics (M24Cxx-W, Device Grade 3) Symbol Test Condition (in addition to those in Table 6.) Parameter Min. Max. Unit VIN = VSS or VCC 2 A VOUT = VSS or VCC, SDA in Hi-Z 2 A VCC=5V, fC=400kHz (rise/fall time < 30ns) 3 mA VCC =2.5V, fC=400kHz (rise/fall time < 30ns) 3 mA VIN = VSS or VCC, VCC = 5 V 5 A VIN = VSS or VCC, VCC = 2.5 V 2 A ILI Input Leakage Current (SCL, SDA, E0, E1,and E2) ILO Output Leakage Current ICC Supply Current ICC1 Stand-by Supply Current VIL Input Low Voltage (1) -0.45 0.3VCC V VIH Input High Voltage (1) 0.7VCC VCC+1 V VOL Output Low Voltage 0.4 V Max. Unit VIN = VSS or VCC 2 A VOUT = VSS or VCC, SDA in Hi-Z 2 A VCC =1.8V, fc=400kHz (rise/fall time < 30ns) 0.8 mA VIN = VSS or VCC, 1.8V < VCC < 5.5V 1 A IOL = 2.1mA when VCC = 2.5V or IOL = 3mA when VCC = 5.5V Note: 1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kOhm. Table 10. DC Characteristics (M24Cxx-R) Symbol Test Condition (in addition to those in Table 7.) Parameter ILI Input Leakage Current (SCL, SDA, E0, E1,and E2) ILO Output Leakage Current ICC Supply Current ICC1 Stand-by Supply Current VIL Input Low Voltage (1) VIH Input High Voltage (1) VOL Output Low Voltage Min. 2.5 V VCC -0.45 0.3 VCC V 1.8 V VCC < 2.5 V -0.45 0.25 VCC V 0.7VCC VCC+1 V 0.2 V IOL = 0.7 mA, VCC = 1.8 V Note: 1. The voltage source driving only E0, E1 and E2 inputs must provide an impedance of less than 1kOhm. Table 11. AC Measurement Conditions Symbol CL Parameter Load Capacitance Input Rise and Fall Times Min. Max. 100 Unit pF 50 ns Input Levels 0.2VCC to 0.8VCC V Input and Output Timing Reference Levels 0.3VCC to 0.7VCC V 17/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 11. AC Measurement I/O Waveform Input Levels Input and Output Timing Reference Levels 0.8VCC 0.7VCC 0.3VCC 0.2VCC AI00825B Table 12. Input Parameters Symbol Parameter1,2 Test Condition Min. Unit CIN Input Capacitance (SDA) 8 pF CIN Input Capacitance (other pins) 6 pF 70 k ZWCL WC Input Impedance VIN < 0.3 V 15 ZWCH WC Input Impedance VIN > 0.7VCC 500 Pulse width ignored (Input Filter on SCL and SDA) Single glitch tNS Note: 1. TA = 25C, f = 400kHz 2. Sampled only, not 100% tested. 18/28 Max. k 100 ns M24C16, M24C08, M24C04, M24C02, M24C01 Table 13. AC Characteristics (M24Cxx-W) Test conditions specified in Table 6. and Table 11. Symbol Alt. Parameter Min. Max. Unit fC fSCL Clock Frequency 400 kHz tCHCL tHIGH Clock Pulse Width High 600 ns tCLCH tLOW Clock Pulse Width Low 1300 ns tDL1DL2 2 tF tDXCX SDA Fall Time 20 300 ns tSU:DAT Data In Set Up Time 100 ns tCLDX tHD:DAT Data In Hold Time 0 ns tCLQX ns tDH Data Out Hold Time 200 tCLQV 3 tAA Clock Low to Next Data Valid (Access Time) 200 tCHDX 1 tSU:STA Start Condition Set Up Time 600 ns tDLCL tHD:STA Start Condition Hold Time 600 ns tCHDH tSU:STO Stop Condition Set Up Time 600 ns tDHDL tBUF Time between Stop Condition and Next Start Condition 1300 ns tWR Write Time tW 4 Note: 1. 2. 3. 4. 900 5 ns ms For a reSTART condition, or following a Write cycle. Sampled only, not 100% tested. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the falling or rising edge of SDA. Previous devices bearing the process letter "L" in the package marking guarantee a maximum write time of 10ms. For more information about these devices and their device identification, please ask your ST Sales Office for Process Change Notices PCN MPG/ EE/0061 and 0062 (PCEE0061 and PCEE0062). Table 14. AC Characteristics (M24Cxx-R) Test conditions specified in Table 7. and Table 10. Max. 4 Unit 400 kHz Alt. fC fSCL Clock Frequency tCHCL tHIGH Clock Pulse Width High 600 ns tLOW Clock Pulse Width Low 1300 ns tCLCH tDL1DL2 2 tF Parameter Min. 4 Symbol SDA Fall Time 20 100 ns tDXCX tSU:DAT Data In Set Up Time Data In Hold Time 300 ns tCLDX tHD:DAT 0 ns tCLQX tDH Data Out Hold Time 200 ns tCLQV 3 tAA Clock Low to Next Data Valid (Access Time) 200 tCHDX 1 tSU:STA Start Condition Set Up Time 600 ns tDLCL tHD:STA Start Condition Hold Time 600 ns tCHDH tSU:STO Stop Condition Set Up Time 600 ns tDHDL tBUF Time between Stop Condition and Next Start Condition 1300 ns tW tWR Write Time Note: 1. 2. 3. 4. 900 10 ns ms For a reSTART condition, or following a Write cycle. Sampled only, not 100% tested. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the falling or rising edge of SDA. This is preliminary information. 19/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 12. AC Waveforms tCHCL tCLCH SCL tDLCL SDA In tCHDX tCLDX START Condition SDA Input SDA tDXCX Change tCHDH tDHDL START STOP Condition Condition SCL SDA In tCHDH tW STOP Condition Write Cycle tCHDX START Condition SCL tCLQV SDA Out tCLQX Data Valid AI00795C 20/28 M24C16, M24C08, M24C04, M24C02, M24C01 PACKAGE MECHANICAL Figure 13. PDIP8 - 8 pin Plastic DIP, 0.25mm lead frame, Package Outline E b2 A2 A1 b A L c e eA eB D 8 E1 1 PDIP-B Note: Drawing is not to scale. Table 15. PDIP8 - 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data millimeters inches Symbol Typ. Min. A Max. Typ. Min. 5.33 A1 Max. 0.210 0.38 0.015 A2 3.30 2.92 4.95 0.130 0.115 0.195 b 0.46 0.36 0.56 0.018 0.014 0.022 b2 1.52 1.14 1.78 0.060 0.045 0.070 c 0.25 0.20 0.36 0.010 0.008 0.014 D 9.27 9.02 10.16 0.365 0.355 0.400 E 7.87 7.62 8.26 0.310 0.300 0.325 E1 6.35 6.10 7.11 0.250 0.240 0.280 e 2.54 - - 0.100 - - eA 7.62 - - 0.300 - - eB L 10.92 3.30 2.92 3.81 0.430 0.130 0.115 0.150 21/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 14. SO8 narrow - 8 lead Plastic Small Outline, 150 mils body width, Package Outline h x 45 A2 A C B ddd e D 8 E H 1 A1 L SO-A Note: 1. Drawing is not to scale. 2. The `1' that appears in the top view of the package shows the position of pin 1 and the `N' indicates the total number of pins. Table 16. SO8 narrow - 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data millimeters inches Symbol Typ Min Max A 1.35 A1 Min Max 1.75 0.053 0.069 0.10 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 ddd Typ 0.10 E 3.80 4.00 - - H 5.80 h 0.004 0.150 0.157 - - 6.20 0.228 0.244 0.25 0.50 0.010 0.020 L 0.40 0.90 0.016 0.035 0 8 0 8 N (number of pins) 8 e 22/28 1.27 0.050 8 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 15. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2x3mm, Outline e D b L1 L3 E E2 L A D2 ddd A1 UFDFPN-01 Note: 1. Drawing is not to scale. 2. The central pad (the area E2 by D2 in the above illustration) is pulled, internally, to VSS. It must not be allowed to be connected to any other voltage or signal line on the PCB, for example during the soldering process. 3. The circle in the top view of the package indicates the position of pin 1. Table 17. UFDFPN8 (MLP8) 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2x3mm, Data millimeters inches Symbol A Typ. Min. Max. Typ. Min. Max. 0.55 0.50 0.60 0.022 0.020 0.024 0.00 0.05 0.000 0.002 0.20 0.30 0.008 0.012 0.061 0.065 A1 b 0.25 D 2.00 D2 0.079 1.55 ddd E 0.010 1.65 0.05 3.00 E2 0.002 0.118 0.15 0.25 0.006 0.010 e 0.50 - - 0.020 - - L 0.45 0.40 0.50 0.018 0.016 0.020 L1 0.15 0.006 L3 0.30 0.012 N (number of pins) 8 8 23/28 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 16. TSSOP8 - 8 lead Thin Shrink Small Outline, Package Outline D 8 5 c E1 1 E 4 A1 A L A2 L1 CP b e TSSOP8AM Note: 1. Drawing is not to scale. 2. The circle in the top view of the package indicates the position of pin 1. Table 18. TSSOP8 - 8 lead Thin Shrink Small Outline, Package Mechanical Data millimeters inches Symbol Typ. Min. A 0.050 0.150 0.800 1.050 b 0.190 c 0.090 A2 Typ. Min. 1.200 A1 1.000 CP Max. 0.0472 0.0020 0.0059 0.0315 0.0413 0.300 0.0075 0.0118 0.200 0.0035 0.0079 0.0394 0.100 0.0039 D 3.000 2.900 3.100 0.1181 0.1142 0.1220 e 0.650 - - 0.0256 - - E 6.400 6.200 6.600 0.2520 0.2441 0.2598 E1 4.400 4.300 4.500 0.1732 0.1693 0.1772 L 0.600 0.450 0.750 0.0236 0.0177 0.0295 L1 1.000 0 8 24/28 Max. 0.0394 0 8 M24C16, M24C08, M24C04, M24C02, M24C01 Figure 17. TSSOP8 3x3mm - 8 lead Thin Shrink Small Outline, 3x3mm body size, Package Outline D 8 5 c E1 1 E 4 L A1 A A2 L1 CP b e TSSOP8BM Note: 1. Drawing is not to scale. 2. The circle in the top view of the package indicates the position of pin 1. Table 19. TSSOP8 3x3mm - 8 lead Thin Shrink Small Outline, 3x3mm body size, Mechanical Data millimeters inches Symbol Typ. Min. A Max. Min. 1.100 A1 0.050 0.150 0.750 0.950 b 0.250 c A2 Typ. 0.850 Max. 0.0433 0.0020 0.0059 0.0295 0.0374 0.400 0.0098 0.0157 0.130 0.230 0.0051 0.0091 0.0335 D 3.000 2.900 3.100 0.1181 0.1142 0.1220 E 4.900 4.650 5.150 0.1929 0.1831 0.2028 E1 3.000 2.900 3.100 0.1181 0.1142 0.1220 e 0.650 - - 0.0256 - - CP 0.100 L 0.550 L1 0.950 0.400 0.700 0.0039 0.0217 0.0157 0.0276 0 6 0.0374 0 6 25/28 M24C16, M24C08, M24C04, M24C02, M24C01 PART NUMBERING Table 20. Ordering Information Scheme Example: M24C16 - W DW 3 T P /W Device Type M24 = I2C serial access EEPROM Device Function 16 = 16 Kbit (2048 x 8) 08 = 8 Kbit (1024 x 8) 04 = 4 Kbit (512 x 8) 02 = 2 Kbit (256 x 8) 01 = 1 Kbit (128 x 8) Operating Voltage W = VCC = 2.5 to 5.5V (400 kHz) R = VCC = 1.8 to 5.5V (400 kHz) Package BN = PDIP8 MN = SO8 (150 mil width) MB = UDFDFPN8 (MLP8) DW = TSSOP8 (169 mil width) DS = TSSOP8 (3x3mm body size, MSOP8) Device Grade 6 = Industrial temperature range, -40 to 85 C. Device tested with standard test flow 3 = Device tested with High Reliability Certified Flow1. Automotive temperature range (-40 to 125 C) Option T = Tape and Reel Packing Plating Technology blank = Standard SnPb plating P or G = ECOPACK(R) (RoHS compliant) Process2 /W or /S = F6SP36% Note: 1. ST strongly recommends the use of the Automotive Grade devices for use in an automotive environment. The High Reliability Certified Flow (HRCF) is described in the quality note QNEE9801. Please ask your nearest ST sales office for a copy. 2. Used only for Device Grade 3. For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest ST Sales Office. 26/28 The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. M24C16, M24C08, M24C04, M24C02, M24C01 REVISION HISTORY Table 21. Document Revision History Date Version 10-Dec-1999 2.4 TSSOP8 Turned-Die package removed (p 2 and order information) Lead temperature added for TSSOP8 in table 2 18-Apr-2000 2.5 Labelling change to Fig-2D, correction of values for `E' and main caption for Tab-13 05-May-2000 2.6 Extra labelling to Fig-2D 23-Nov-2000 3.0 SBGA package information removed to an annex document -R range changed to being the -S range, and the new -R range added 19-Feb-2001 3.1 SBGA package information put back in this document Lead Soldering Temperature in the Absolute Maximum Ratings table amended Write Cycle Polling Flow Chart using ACK illustration updated References to PSDIP changed to PDIP and Package Mechanical data updated Wording brought in to line with standard glossary 20-Apr-2001 3.2 Revision of DC and AC characteristics for the -S series 08-Oct-2001 3.3 Ball numbers added to the SBGA connections and package mechanical illustrations 09-Nov-2001 3.4 Specification of Test Condition for Leakage Currents in the DC Characteristics table improved 30-Jul-2002 3.5 Document reformatted using new template. SBGA5 package removed TSSOP8 (3x3mm body size) package (MSOP8) added. -L voltage range added 04-Feb-2003 3.6 Document title spelt out more fully. "W"-marked devices with tw=5ms added. 05-May-2003 3.7 -R voltage range upgraded to 400kHz working, and no longer preliminary data. 5V voltage range at temperature range 3 (-xx3) no longer preliminary data. -S voltage range removed. -Wxx3 voltage+temp ranged added as preliminary data. 07-Oct-2003 4.0 Table of contents, and Pb-free options added. Minor wording changes in Summary Description, Power-On Reset, Memory Addressing, Read Operations. VIL(min) improved to -0.45V. tW(max) value for -R voltage range corrected. 17-Mar-2004 5.0 MLP package added. Absolute Maximum Ratings for VIO(min) and VCC(min) changed. Soldering temperature information clarified for RoHS compliant devices. Device grade information clarified. Process identification letter "G" information added. 2.2-5.5V range is removed, and 4.5-5.5V range is now Not for New Design 7-Oct-2005 6.0 Product List summary table added. AEC-Q100-002 compliance. Device Grade informaton clarified. Updated Device internal reset section, Figure 4., Figure 5., Table 14. and Table 20. Added Ecopack(R) information. Updated tW=5ms for the M24Cxx-W. 7.0 Pin numbers removed from silhouettes (see Figure 1., Packages). Internal Device Reset paragraph moved to below Supply voltage (VCC). Supply voltage (VCC) added below SIGNAL DESCRIPTION. Test conditions for VOL updated in Table 8. and Table 9. SO8N package specifications updated (see Table 16.) New definition of ICC1 over the whole VCC range (see Tables 8, 9 and 10). 17-Jan-2006 Description of Revision 27/28 M24C16, M24C08, M24C04, M24C02, M24C01 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 28/28