6-119216-6 - Tyco Electronics

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

ACTION PIN Press-Fit Contacts

The Reliable Plated Through-

Hole Interconnect

Solderless interconnections

have been popular in elec-

trical and electronic appli-

cation with world-wide

success for decades. They

provide reliable electrical

and mechanical stability

and offer applied-cost sav-

ings across the board. For

PC board applications,

ACTION PIN contacts from

Tyco Electronics provide

these features:

n Large gas-tight contact

zone

n Reliability due to stored

energy in compliant pin

contacts

n No damage to plated

through-holes during

installation

n Especially suited for mul-

tilayer PC boards

n Less costly board manu-

facturing due to larger

hole tolerances com-

pared to use of solid

pins

n Application can be

made by end-user

n Repairability—contact

can be replaced in the

same pin location (two

repairs)

n Installation with no heat

cycling of board

n Permits mass insertion

by minimizing forces

needed to insert pins as

compared to solid pin

press-fit application

n Significant applied-cost

savings in many applica-

tions

Since ACTION PIN contacts

do not have to be soldered,

issues associated with sol-

der are eliminated, such as:

• Faulty solder joints

• Solder fumes; cont-

aminant’s are

deposited on the

contacts

• Solder spots; short

circuits between

printed circuits

• Flux residuals

• Thermal strain on

printed circuit

boards and

components

• Degasing of plated

through-holes

Solderless press-fit inter-

connections using the

ACTION PIN contact are

primarily integrated in, but

not limited to, backplanes.

Solderless press-fit inter-

connections are used in

racks, especially where

connectors must be fixed

on the solder side of the PC

board and/or component

side. In these applications,

the holes for ACTION PIN

contact connectors are cov-

ered during the soldering

process and press-fitting is

performed after soldering.

Other applications for

ACTION PIN contact

interconnections include PC

boards that incorporate

components using surface

mount technology (SMT).

Here, too, press-fit intercon-

nections can be applied

after soldering, thus elimi-

nating complications

associated with connectors

suitable for surface

mounting.

Principle of the Tyco

Electronics Compliant

ACTION PIN Contact

When an ACTION PIN con-

tact is inserted into a plated

through-hole, two spring

members are compressed,

exerting force against the

hole for gas-tight connec-

tion. The diameter of the

hole is smaller than the

diagonal size of the pin

(see cross-section illustra-

tion below).

The beam characteristics of

the pin are designed so

that a plastic, as well as an

elastic, deformation takes

place during insertion. The

two spring members com-

press to different degrees

to accommodate hole toler-

ances. The compliant pin

also reduces strain on the

board. With a rigid pin, the

elastic strain energy is

stored entirely in the board,

leading to damage of the

plated through-holes. With

the ACTION PIN contact,

the residual force of the

elastic deformation main-

tains stored energy to pro-

duce a tight contact zone

between the pin and the

plated through-hole. This

provides long term electri-

cal and mechanical reliabili-

ty of the interconnection.

Cross-Section Area from Tyco Electronics ACTION PIN Press-Fit

Contact in Printed Circuit Board Holes from Tyco Electronics.

Note: ACTION PIN contact mounting hole specifications are presented in

each product section, where applicable.

Minimum

Hole Dia.

.037 [0.94]

Maximum

Hole Dia.

.043 [1.09]

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors

AMP PACE (Pre-Assembled

Card Edge) Connectors are

the latest innovation in the

evolution of backplane archi-

tecture. Designed to short-

en manufacturing time and

reduce applied costs, these

one-step, pre-assembled

connectors are ready for

mounting and mass inser-

tion. In addition, design

features such as removable

housings and contacts, that

are replaceable through the

top of the connector

housing, for maximum

flexibility in your backplane

packaging.

At the heart of the

AMP PACE Connector is

AMP’s proven and reliable

ACTION PIN Contact. This

unique contact has superior

electrical and physical

characteristics that are top

of the line in the industry.

AMP PACE Connectors are

available with post center-

line spacings of:

.100 x .100 [2.54 x 2.54]

.100 x .200 [2.54 x 5.08]

.125 x .125 [3.18 x 3.18]

.125 x .250 [3.18 x 6.35]

.156 x .200 [3.96 x 5.08]

Important:

Application tooling is

absolutely necessary to

insert connectors into PC

boards. See page 115 for

application tooling.

Performance Specifications

Electrical Characteristics

Contact Resistance: ACTION PIN

Contact Interface—5 milliohm

Spring Contact to Test Board—11.5

milliohms

Total Circuit Resistance:

12 milliohms

Continuous Current Rating*:

3 amperes

Insulation Resistance:

5,000 milliohms

Dielectric Withstanding Voltage:

.100 [2.54] Centerline Spacing—

1,000 VAC at sea level;

350 VAC at 50,000 ft. [15,240 m];

275 VAC at 70,000 ft. [21,336 m]

.125 [3.18] Centerline Spacing—

1,500 VAC at sea level;

500 VAC at 50,000 ft. [15,240 m];

235 VAC at 70,000 ft. [21,336 m]

Physical Characteristics

Card Insertion Force (Max.):

16 oz [4.45 N] per contact pair

ACTION PIN Contact Post

Card Extraction Force (Min.):

1 oz [.278 N] per contact pair

ACTION PIN Contact Post

Retention (in PC board):

.100 x .100 [2.54 x 2.54]—

7.5 lb. [33.4 N] min.

Operating Temperature:

–55°C to +85°C

Durability: Tested to 100 cycles (100

insertions and withdrawals at a rate not

exceeding 10 cycles per minute)

Salt Spray: MIL-STD-1344,

Method 1001

Physical Shock: MIL-STD-1344,

Method 2004

Thermal Shock: MIL-STD-1344,

Method 1003, Cond. A

Humidity: MIL-STD-1344,

Method 1002, Type II

Vibration: MIL-STD-1344,

Method 2005

*Consult Tyco Electronicsengi-

neering when paralleling con-

tacts for power applications.

Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E28476

Certified by

Canadian Standards

Association,

File No. LR7189

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors (Continued)

Product Facts

Repairability Details

Repairability—

(See below for details)

Individual contacts can be removed

without removing the housing;

housings can be removed without

removing posts. Important: APC board

must be inserted into the connector

when removing the contact.

Precision Plated Contacts—

Selective plating puts gold where

it is needed for superior electrical

contact at a reasonable cost.

Beam Contact Design—

The contact’s unique beam design

accommodates and compensates

for daughter board warp and

stress providing long-term, reliable

performance (100 gram minimum

normal force).

Gas-Tight Connection—

Spring sections of ACTION PIN

Contacts compress in opposite

directions, maintaining a gas-tight

fit with the PC board.

Contact Tip Alignment Strip—

Polyester strip provides straight

and stable pin alignment for

damage-free entry into the

PC board. Precision Plated Post—

Gold plating can be applied to the

entire post, or just the post tip for

improved pluggability.

Remove and replace contacts

without removing housing.

(See page 115 for Contact

Replacement Tools.)

Remove and replace housing

without removing contacts.

100

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline

Standard Housing

Typical Closed End/

Open End Housings

Keying Plugs

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .475 [12.07]

Post Length

Connectors can be

mounted in pairs using

any size combinations.

Example:

1-30 pos. + 1-60 pos.

= 1-90 pos.

C±.006

[±0.15]

.100

[2.54]

.415

[10.54]

Card Slot

Depth

.380

[9.65]

.005/.007

[0.13/0.18]

See E Below

Post Length

and

Finish Area

.040

[1.02] Min.

Contact Finish Area

.025

[0.64] Sq.

Post

.100

[2.54]

.100

[2.54]

.135

[3.43]

Detail E

Intercontact (Plastic)

Part No. 118982-1 On-Contact (Plastic)

Part No. 119802-2

.100

[2.54]

101

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. nickel in

contact area, .000100 [0.00254] min.

tin-lead on posts, with entire contact

underplated .000050 [0.00127] min.

nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-2978,

408-2979, 408-6881, 408-9091,

408-9188

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

No. of Dimensions Post Closed/Closed Closed/Open

Dual

Positions ABCLength Standard Scoop Standard

.180

1.400 1.734 1.604 4.57 119734-1 119736-1 —

15 35.56 44.04 40.74 .475

12.07 119237-1 — —

1.900 2.234 2.104 .180

20 48.26 56.74 53.44 4.57 119734-6 — —

2.400 2.734 2.604 .180

25 60.96 69.44 66.14 4.57 1-119734-1 — —

2.700 3.034 2.904 .180

28 68.58 77.06 73.76 4.57 1-119734-4 — —

3.000 3.334 3.204 .475

31 76.20 84.68 81.38 12.07 1-119237-7 — —

.180

3.400 3.734 3.604 4.57 2-119734-1 — 119831-6

35 83.36 94.84 91.54 .475

12.07 — — 119413-6

3.900 4.234 4.104 .180

40 99.06 107.54 104.24 4.57 2-119734-6 2-119736-6 —

4.700 5.034 4.904 .475

48 119.38 127.86 124.56 12.07 3-119237-4 — —

4.900 5.234 5.104 .180

50 124.46 132.94 129.64 4.57 3-119734-6 — —

5.900 6.234 6.104 .180

60 149.86 158.34 155.04 4.57 4-119734-6 4-119736-6 —

Note: Other connector sizes and connectors with card scoops can be made available, consult Tyco Electronics.

102

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline

Standard Housing

Housing with High Card

Scoops

Keying Plugs

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .475 [12.07]

and .702 [17.83]

Post Lengths

C±.006

[±0.15]

.100

[2.54]

.415

[10.54]

Card Slot

Depth

.360

[9.14]

.005/.007

[0.13/0.18]

See E Below

Post Length

and

Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.545

[13.84]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.200

[5.08]

.515

[13.08]

Card Slot

Depth

.390

[9.91]

.005/.007

[0.13/0.18]

See E Below

Post Length

and

Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.645

[16.38]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.200

[5.08]

.135

[3.43]

.100

[2.54]

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .475 [12.07]

and .702 [17.83]

Post Lengths

Detail E On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

C±.006

[±0.15]

.100

[2.54]

.100

[2.54]

103

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. nickel in

contact area, .000100 [0.00254] min.

tin-lead on posts, with entire contact

underplated .000050 [0.00127] min.

nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-2933,

408-2978, 408-2979, 408-9058,

408-9067, 408-9091, 408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

No. of Dimensions Post Closed End/Closed End

Dual

Positions ABCLength Standard High Scoop

.900 1.234 1.104 .180

10 22.86 31.34 28.04 4.57 —1-650297-1

1.400 1.734 1.604 .180

15 35.56 44.04 40.74 4.57 1-119738-1 119791-1

1.700 2.034 1.904 .180

18 43.18 51.66 48.36 4.57 1-119738-4 —

1.900 2.234 2.104 .180

20 48.26 56.74 53.44 4.57 1-119738-6 —

.180

2.100 2.434 2.304 4.57 1-119738-8 —

22 53.34 61.82 58.52 .475

112.07 -119216-8 650123-8

2.300 2.634 2.504 .180

24 58.42 66.90 63.60 4.57 1-119738-0 —

.180

2.400 2.734 2.604 4.57 1-119738-1 —

25 60.96 69.44 66.14 .702

17.83 1-119163-1 —

.180

2.700 3.034 2.904 4.57 1-119738-4 —

28 68.58 77.06 73.76 .475

12.07 1-119216-4 —

.180

4.57 1-119738-6 1-119791-6

2.900 3.234 3.104 .475

30 73.66 82.14 78.84 12.07 1-119216-6 —

.702

17.83 1-119163-6 —

3.000 3.334 3.204 .180

31 76.20 84.68 81.38 4.57 1-119738-7 —

3.100 3.434 3.304 .180

32 78.74 87.22 83.92 4.57 1-650122-8 —

.180

34 3.300 3.634 3.504 4.57 — 2-119791-0

83.82 92.30 88.90 .475

12.06 2-119216-0 —

3.400 3.734 3.604 .475

35 86.36 94.84 91.54 12.06 2-119216-1 —

.180

3.500 3.834 3.704 4.57 2-119738-2 —

36 88.90 97.38 94.08 .475

12.06 2-119216-2 —

3.600 3.934 3.804 .180

37 91.44 99.92 96.62 4.57 2-650122-3 —

.180

3.900 4.234 4.104 4.57 2-119738-6 —

40 99.06 107.54 104.24 .475

12.06 2-119216-6 —

4.200 4.534 4.404 .180

43 106.68 115.16 111.86 4.57 2-650122-9 —

4.300 4.634 4.504 .475

44 109.22 117.70 114.40 12.07 3-119216-0 —

.180

4.57 3-119738-6 3-119791-6

4.900 5.234 5.104 .475

50 124.46 132.94 129.64 12.07 3-119216-6 —

.702

17.83 — 3-119726-6

5.400 5.734 5.604 .180

55 137.16 145.54 142.34 4.57 4-119738-1 4-650124-1

.180

5.900 6.234 6.104 4.57 4-119738-6 —

60 149.86 158.34 155.04 .702

17.83 119677-1 —

Note: Other connector sizes can be made available, consult Tyco Electronics.

104

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connectors, .125 x .125 [3.18 x 3.18] Centerline

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. palladium-

nickel in contact area, .000100

[0.00254] min. tin-lead on posts, with

entire contact underplated .000050

[0.00127] min. nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-6727,

408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

Housing with High Card

Scoops

28 Dual Positions

Part Number 1-119853-4

Keying Plugs

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

and .702 [17.83]

Post Length

.125

[3.18]

3.755

[95.38]

3.625±.006

[92.08±0.15]

3.375

[85.72]

.125

[3.18]

.515

[13.08]

Card Slot

Depth

.420

[10.67]

.005/.007

[0.13/0.18]

See E Below

.702

[17.83]

Post Length

and Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.025

[0.64] Sq.

Post

.125

[3.18]

.135

[3.43]

Detail E

On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

105

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Solder Type, Board-to-Board)

AMP PACE Connector Specials, .125 x .125 [3.18 x 3.18] Centerline

27 Dual Positions

Tin-Lead Posts

.634 [16.10] Long

Part No. 645394-1

18 or 36

Dual Positions

Tin-Lead Posts

.740 [18.80] Long

Part No. 119552-2

Tin-Lead Posts

.180 [4.57] Long

Part No. 119880-1

97 Dual Positions

(Two-piece Closed

End/Open End with Partial

Card Scoops and Card

Guides)

Contact Tyco Electronics for

specific Part Number infor-

mation.

106

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline

Standard Housing

Housing with High Card

Scoops

Typical Closed End/

Open End Housings

Keying Plugs

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .500 [12.07]

and .702 [17.83]

Post Lengths

C±.006

[±0.15]

.125

[3.18]

.415

[10.54]

Card Slot

Depth

.410

[10.41]

.005/.007

[0.13/0.18]

See E Below

.702

[17.83]

Post Length

and Finish Area

.702

[17.83]

Post Length

and Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.545

[13.84]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.250

[6.35]

.515

[13.08]

Card Slot

Depth

.420

[10.67]

.005/.007

[0.13/0.18]

See E Below

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.645

[16.38]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.250

[6.35]

.135

[3.43]

.125

[3.18]

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .500 [12.07]

and .702 [17.83]

Post Lengths

Detail E On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

C±.006

[±0.15]

.125

[3.18]

.125

[3.18]

3.375

[85.72]

Connectors can be

mounted in pairs using

any size combinations.

Example:

1-30 pos. + 1-60 pos.

= 1-90 pos.

.125

[3.18]

Card Edge Connectors

(Press-Fit Board-To-Board)

107

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline (Continued)

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. nickel in

contact area, .000100 [0.00254] min.

tin-lead on posts, with entire contact

underplated .000050 [0.00127] min.

nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-2933,

408-2978, 408-2979, 408-9063,

408-9091, 408-9119, 408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

No. of Dimensions Post Closed End/Closed End Closed End/Open End

Dual

Positions A B C Length Standard High Scoop High Scoop

2.125 2.373 2.505 .180

18 53.98 60.27 63.63 4.57 1-119822-4 — 3-119840-2

.180

4.57 1-119822-8 — —

2.625 3.005 2.875 .500

22 66.68 76.33 73.02 12.70 1-119200-8 — —

.702

17.83 1-119202-8 — —

3.000 3.380 3.250 .180

25 76.20 85.85 82.55 4.57 1-119822-1 — —

3.250 3.630 3.500 .702

27 82.55 92.20 88.90 17.83 1-119202-3 — —

.180

3.375 3.755 3.625 4.57 1-119822-4 — —

28 85.72 95.38 92.08 .500

12.70 1-119200-4 — —

.180

3.625 4.005 3.875 4.57 1-119822-6 1-678034-1 —

30 92.08 101.73 98.24 .500

12.70 — 1-119841-6 —

.180

4.375 4.755 4.625 4.57 2-119822-2 1-678034-2 —

36 111.82 120.78 117.48 .500

12.70 — 2-119841-2 —

4.625 4.873 5.005 .180

38 117.47 123.77 127.13 4.57 2-119822-4 — 3-119840-9

.180

4.875 5.255 5.125 4.57 2-119822-6 — —

40 123.83 133.48 130.18 .702

17.83 2-119200-6 — —

6.125 6.505 6.375 .180

50 155.58 165.23 161.93 4.57 3-119822-6 — —

6.250 6.630 6.500 .500

51 158.75 168.40 165.10 12.70 3-119200-7 — —

7.375 7.755 7.625 .180

60 187.33 196.98 193.68 4.57 4-119822-6 — —

Note: Other connector sizes can be made available, consult Tyco Electronics.

108

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make

Before Break Contacts

Standard Housing

Housing with High Card

Scoops

Typical Closed End/

Open End Housings

Keying Plugs

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .500 [12.07]

and .702 [17.83]

Post Lengths

C±.006

[±0.15]

.125

[3.18]

.415

[10.54]

Card Slot

Depth

.410

[10.41]

.005/.007

[0.13/0.18]

See E Below

.702

[17.83]

Post Length

and Finish Area

.702

[17.83]

Post Length

and Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.545

[13.84]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.250

[6.35]

.515

[13.08]

Card Slot

Depth

.420

[10.67]

.005/.007

[0.13/0.18]

See E Below

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.645

[16.38]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.250

[6.35]

.135

[3.43]

.125

[3.18]

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

Contact Tip

Alignment Strip

on .500 [12.07]

and .702 [17.83]

Post Lengths

Detail E On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

C±.006

[±0.15]

.125

[3.18]

.125

[3.18]

3.375

[85.72]

Connectors can be

mounted in pairs using

any size combinations.

Example:

1-30 pos. + 1-60 pos.

= 1-90 pos.

.125

[3.18]

109

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make

Before Break Contacts (Continued)

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. nickel in

contact area, .000100 [0.00254] min.

tin-lead on posts, with entire contact

underplated .000050 [0.00127] min.

nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-2933,

408-2978, 408-2979, 408-9063,

408-9091, 408-9119, 408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

No. of Dimensions Post Closed End/Closed End Closed End/Open End

Dual

Positions A B C Length Standard High Scoop

2.125 2.505 2.373 .180

18 53.98 63.63 60.27 4.57 1-1571235-1 —

2.875 3.123 3.058 .180

24 76.20 79.25 77.67 4.57 — 650059-2

Note: Other connector sizes can be made available, consult Tyco Electronics.

110

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold .000030 [0.00076] min. thk. over

.000050 [0.00127] min. thk. nickel in

contact area, .000100 [0.00254] min.

tin-lead on posts, with entire contact

underplated .000050 [0.00127] min.

nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-6726,

408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

Standard Housing

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards Contact Tip

Alignment Strip

on .475 [12.07]

and .702 [17.83]

Post Lengths

C±.006

[±0.15]

.156

[3.96]

.156

[3.96]

.415

[10.54]

Card Slot

Depth

.360

[9.14]

.005/.007

[0.13/0.18]

See E Below

Post Length

and

Finish Area

.040

[1.02] Min.

Contact

Finish Area

.364

[9.24]

.545

[13.84]

.025

[0.64] Sq.

Post .093

[2.36] Min.

.200

[5.08]

Keying Plugs

.135

[3.43] Detail E

On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

No. of Dimensions Post Closed End/Closed End

Dual

Positions A B C Length Standard

.180

4.57 1-119790-1

2.184 2.626 2.495 .475

15 55.47 66.70 63.39 12.07 1-119254-1

.702

17.83 1-119256-1

2.652 3.094 2.964 .475

18 67.36 78.59 75.29 12.07 1-119254-4

.180

4.57 1-119790-8

3.276 3.718 3.588 .475

22 83.21 94.44 91.13 12.07 1-119254-8

.702

17.83 1-119256-8

.180

4.57 1-119790-4

4.212 4.654 4.524 .475

28 106.98 118.21 114.91 12.07 1-119254-4

.702

17.83 1-119256-4

.180

4.57 2-119790-9

6.552 6.994 6.864 .475

43 166.42 177.65 174.35 12.07 2-119254-9

.702

17.83 2-119256-9

Note: Other connector sizes can be made available, consult Tyco Electronics.

111

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline w/Make

Before Break Contacts

Material and Finish:

Housing—Black glass-filled polyester,

94V-0 rated

Contacts—Phosphor bronze, plated

gold flash over .000030 [0.00076] min.

thk. over .000050 [0.00127] min. thk.

nickel in contact area, .000100

[0.00254] min. tin-lead on posts, with

entire contact underplated .000050

[0.00127] min. nickel

Contact Tip Alignment Strip—Clear

polyester, type D

Related Product Data:

Performance Specifications—

page 98

Accessories—page 112

PC Board Edge Pattern—page 113

ACTION PIN Contact Mounting

Hole Specifications—page 114

Application Tooling—page 115

Contact Replacement Tools—

page 115

Special Application—page 96

Technical Documents:

(pages 186, 187):

Product Specifications

108-14019, 108-26003

Application Specification

114-26002

Instruction Sheets 408-6726,

408-9186

Note: Full palladium-nickel plated

posts and other platings and plating

thicknesses can be made available.

Card Scoop Housing

.228

[5.78]

.364

[9.25]

.005/.007

[0.13/0.18] .200

[5.08]

.116

[2.95] Contact Area

.093

[2.36] Min.

.045

[1.14] Contact Area

Keying Plugs

.135

[3.43]

Detail E

On-Contact (Plastic)

Part No. 119802-2

Intercontact (Plastic)

Part No. 118982-1

No. of Dimensions Post Closed End/Closed End

Dual

Positions A B C Length Scoop

2.652 3.094 2.964 .180

18 67.36 78.59 75.29 4.57 678035-1

Note: Other connector sizes can be made available, consult Tyco Electronics.

Accepts

.054 to .071

[1.37 to 1.80]

PC Boards

.156

[3.96]

.156

[3.96]

112

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Accessories for AMP PACE Connectors

Material: Black glass-filled polyester

Related Product Data:

Mates with all standard housings (will

not mate with some special housings)

Technical Documents:

(pages 186, 187):

Instruction Sheet 408-9091

Connector Card Guide

Rating:

20 amperes per contact—Copper or

aluminum bus

Material and Finish:

Housing—Black glass-reinforced

thermoplastic

Contact—CA 195, 3/4 hard, plated

.000050 [0.00127] gold in contact area

(front face only); .000100 [0.00254] tin-

lead on post, with entire contact under-

plated .000050 [0.00127] nickel

Related Product Data:

Mates with all standard housings (will

not mate with some special housings)

Technical Documents:

(pages 186, 187):

Instruction Sheet 408-2978

Ground Module

L1Part Numbers

2.500

63.50 1-117169-3

6.000

152.40 1-117169-3

1Other lengths up to 6.0 [152.4] can be

made available. Consult Tyco

E l e c t r o n i c s for details.

BDimension from

AMPPACEConnector

Tables Plus .310 [7.87]

Hole for

#4 Self-Tapping

Screw

(mandatory)

.050 [12.7] Deep

Accepts

.054 to.071

[1.37 to 1.80]

PC Board

.410

[10.41] .220

[5.59]

.420

[10.67]

.455

[11.56]

.250

[6.35]

.300

[7.62]

.700

[17.78]

.370

[9.4]

.060

[1.52]

Contact

Area

Part No. 119341-1

Seating Tool 59881-1

.152

[3.96] Dia.

(2 Holes)

113

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

PC Board Layout for AMP PACE Connectors

Recommended

PC Board Edge Pattern

.430

[10.92]

Gold

Fingers

.050

[1.27]

Max. Chamfer

.275

[6.99]

.052±.002

[1.32±0.05]

Key Slot

C±.005

[±0.13]

.040 +.020

-.010

[1.016+.508

-.254 ]

30°

.054-.071

[1.37-1.80]

1A Max. = Minimum connector card slot -.001 [-0.03].

A Min. = Minimum connector card slot -.011 [-0.28].

Note: Finger pattern to be centered on daughter card.

Each finger can deviate .003 [0.08] from true position.

AMP PACE Connector Dimensions

Centerline Spacing B C

.100 x .100 .100 .070

2.54 x 2.54 2.54 1.78

.100 x .200 .100 .070

2.54 x 5.08 2.54 1.78

.125 x .125 .125 .080

3.18 x 3.18 3.18 2.03

.125 x .250 .125 .080

3.18 x 6.35 3.18 2.03

.156 x .200 .156 .080

3.96 x 5.08 3.96 2.03

114

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

AMP PACE Connectors (Continued)

AMP ACTION PIN

Press-Fit Contacts

ACTION PIN contacts provide a reliable press-fit connection.

Localized pressure in the interface area entails oxide

break-through and helps prevent corrosion in the harshest

environments to provide a reliable connection virtually every

time. Also, radial and axial distortion are controlled to meet

today’s standards for multilayer board applications.

PC Board Thickness

ACTION PIN contacts are

designed for use in a variety of

PC board thicknesses. However,

certain ACTION PIN contacts

are to be used in specific

ranges of board thicknesses. To

promote optimum performance,

the recommended board thick-

nesses provided with the con-

nector being used must be

followed. ➀Annular Ring (See Note)

➁Drilled Hole

➂Copper Thickness

➃Tin-Lead Thickness

➄Plated Through-Hole

Mounting Hole Specifications

Connector ACTION PIN Contact Drilled Hole Plating Thicknesses Plated Radial Hole Distortion

No. of Dual Material Through-Hole

Centerline Positions Thickness Diameter➁Copper➂* Tin-Lead➃Diameter➄Average Maximum

.125 x .125

3.18 x 3.18 28, 97 .025 .0453±.001 .001-.003 .0003 .037-.043 Not Not

.156 x .200 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 Specified Specified

3.96 x 5.08 15-43 Min.

.125 x .125 .025 .0465±.001 .001-.003 .0003 .037-.043 Not Not

27 0.008

3.18 x 3.18 0.64 1.181±0.03 0.03-0.08 Min. 0.94-1.09 Specified Specified

.100 x .100

2.54 x 2.54 15-60

.100 x .200

2.54 x 5.08 15-60 .025 .0453±.001 .001-.003 .0003 .037-.043 .0015 .002

.125 x .125 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 0.038 0.05

3.18 x 3.18 18, 36 Min.

.125 x .250

3.18 x 6.35 18-60

*Maximum hardness of copper layer is 150 Knoop.

Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].

115

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Application Tooling for AMP PACE Connectors

Modular Seating Tools

Available from Tyco

Electronics is

a complete series of

AMP PACE Modular

Seating Tools for installing

AMP PACE Connectors on

printed circuit boards and

panels. These tools are

modular in design in that

housing tool holders may

be added or subtracted to

accommodate several dif-

ferent connector sizes. In

addition, all tool parts are

individually replaceable

should the tool become

damaged.

Modular seating tools are

supplied in two basic

designs: One which covers

all connector centerlines

except .100 x .100 [2.54 x

2.54] and one for the .100 x

.100 [2.54 x 2.54] centerline

connectors.

All seating tools have a

common shut height of

1.5 inches [38]. This

allows AMP PACE and other

ACTION PIN products to be

seated at the same time on

AMP seating machines. See

page 149 for a description

of the AMP seating

machines.

.100 x .100 [2.54 x 2.54]

Centerline Spacing .100 x .200 [2.54 x 5.08], .156 x .200 [3.96 x 5.08]

.125 x .125 [3.18 x 3.18], Centerline Spacing

.125 x .250 [3.18 x 6.35],

No. of Centerline

Dual .100 x .100 .100 x .200 .125 x .250 .156 x .200

Positions [2.54 x 2.54] [2.54 x 5.08] [3.18 x 6.35] [3.96 x 5.08]

15 1-58200-1 1-58140-1 — 1-58143-1

18 — 1-58140-4 1-58142-4 —

20 1-58200-6 1-58140-6 — —

22 — 1-58140-8 1-58142-8 1-58143-8

25 1-58200-1 1-58140-1 1-58142-1 —

28 1-58200-4 1-58140-4 1-58142-4 1-58143-4

30 1-58200-6 1-58140-6 1-58142-6 —

31 1-58200-7 — — —

32 — 1-58140-8 — —

34 — 2-58140-0 — —

35 2-58200-1 2-58140-1 — —

36 — 2-58140-2 2-58142-2 —

37 — 2-58140-3 — —

40 2-58200-6 2-58140-6 2-58142-6 —

43 — 2-58140-9 — 2-58143-9

44 — 3-58140-0 — —

48 3-58200-4 — — —

50 3-58200-6 3-58140-6 3-58142-6 —

51 3-58200-7 — 3-58142-7 —

54 4-58200-0 — — —

55 4-58200-1 4-58140-1 — —

56 — — 4-58142-2 —

60 4-58200-6 4-58140-6 4-58142-6 —

For Connectors without Scoops

For Connectors with Scoops

No. of Centerline

Dual .100 x .200 .125 x .125 .125 x .250

Positions [2.54 x 5.08] [3.18 x 3.18] [3.18 x 6.35]

15 1-58150-1 — —

18 — — 1-58184-4

22 1-58150-8 — —

28 — 1-58218-4 —

30 1-58150-6 — —

38 — — 2-58184-4

50 3-58150-6 — 3-58184-6

55 4-58150-1 — —

Contact Replacement

Tools

Replacement tools listed in

the chart at the right are

used to install replacement

contacts in AMP PACE con-

nector housings. Replace-

ment Tool 1-265871-7 is

used to remove all .025

[0.64] square posts from

PC boards.

Housing Style

Centerline Standard Full Card Scoop

.100 x .100

2.54 x 2.54 266220-3 —

.100 x .200

2.54 x 5.08 266220-1 58210-1

.125 x .125

3.18 x 3.18 — 58210-4

.125 x .250

3.18 x 6.35 266220-2 58210-2

.156 x .200

3.96 x 5.08 266220-2 —

Note: Tooling availability is

dependent upon part number

activity. Consult Tyco

Electronics for further

information.

116

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

TELEDENSITY Connectors

Product Facts

■High density - .0625 [1.586]

contact centerlines

■Compliant ACTION PIN

contacts press-fit into

plated-through holes for

solderless application

■Individually replaceable

contacts

■Accommodates up to three

levels of daughter card pads

for sequencing

■.125 [3.18] square grid post

arrangement

The high performance AMP

TELEDENSITY connector is

a high density, card edge,

telecommunications con-

nector. It features compliant

ACTION PIN contacts for

solderless application to

multi-layer printed circuit

boards with plated-through

or bare copper holes.

These connectors accept

.054 to .072 [1.37 to 1.83]

thick daughter cards. To

satisfy the broadest range

of application needs, the

contacts are plated with 30

microinches of gold in the

mating area and tin-lead on

the posts. A plastic locating

strip keeps posts positioned

correctly for board insertion.

For high-density needs,

TELEDENSITY connectors

offer a .0625 [1.586] daugh-

ter card contact centerline

spacing in 39-, 71-, or 99-

dual positions. The connec-

tor’s .330 [8.38] slot depth

accommodates up to three

levels of daughter card

pads for sequencing, while

a biasing wedge maintains

proper pad alignment dur-

ing card extraction. Posts

are arranged in a .125

[3.18] square grid to ease

circuit routing.

Performance Specifications

Current Rating*:

3 amperes max.

Mating Force (Contact Pair):

1 lb. [4.4 N] max.

Durability (Mating Cycles):

100 min.

Termination Resistance:

12 milliohms max.

Dielectric Rating:

1200 VAC (rms)

Insulation Resistance:

5000 megohms max.

Operating Temperature:

–55°C to +85°C

*Consult Tyco Electronics

when paralleling contacts

for power applications.

117

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Material and Finish:

Housing—Black polyester

Contacts—Copper alloy 725, plated

.000030 [0.00076] gold in contact area,

.000030 [0.00076] solder plate on post,

with entire contact underplated .000100

[0.00254] nickel

Coil Spring—Stainless steel

Contact Tip Alignment Strip—Clear

polyester

Related Product Data:

Performance Specifications—

page 116

ACTION PIN Contact Mounting

Hole Specifications—page 118

Technical Document—pages 186,

187

Product Specification—

108-26003

Instruction Sheet—

408 6866

TELEDENSITY Connectors, .0625 [1.586] Centerline

Recommended

PC Board Layout

(Shown from post side)

Number of Dimensions Connector Seating

Dual Part Tool

Positions A B C D Numbers Numbers**

.634 650148-1

39 3.168 2.588-2.600 16.10 2.375 58084-1

80.47 65.74-66.04 .350 60.33 650281-1*

8.89

71 5.168 4.588-4.600 .634 4.375 650149-1 58084-3

131.27 116.54-116.84 16.10 111.13

99 6.918 6.338-6.350 .634 6.125 650150-1 58084-2

175.72 160.99-161.29 16.10 155.58

* Contacts in this connector are underplated .000150 [0.00381] nickel.

** See page 149 for a description of AMP seating machines.

Note: ACTION PIN posts require .093 [2.36] min. thick PC board.

For mounting hole specifications, see page 123

118

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

TELEDENSITY Connectors (Continued)

AMP ACTION PIN

Press-Fit Contacts

ACTION PIN contacts provide a reliable press-fit connection.

Localized pressure in the interface area entails oxide

breakthrough and helps prevent corrosion in the harshest

environments to provide a reliable connection virtually every

time. Also, radial and axial distortion are controlled to meet

today’s standards for multilayer board applications.

PC Board Thickness

ACTION PIN contacts are

designed for use in a variety of

PC board thicknesses. However,

certain ACTION PIN contacts

are to be used in specific ranges

of board thicknesses. To

promote optimum performance,

the recommended board thick-

nesses provided with the con-

nector being used must be

followed.

➀Annular Ring (See Note)

➁Drilled Hole

➂Copper Thickness

➃Tin-Lead Thickness

➄Plated Through-Hole

Mounting Hole Specifications

ACTION PIN Drilled Hole Plating Thicknesses P l a t e d - T h r o u g h Radial Hole Distortion

C o n t a c t D i a m e t e r

➁

C o p p e r

➂

*T i n - L e a d

➃

H o l e A v e r a g e M a x i m u m

Material Thickness D i a m e t e r

➄

. 0 2 5 . 0 4 5 3 ± . 0 0 1 . 0 0 1 - . 0 0 3 .0003 M i n . . 0 3 7 - . 0 4 3 . 0 0 1 5 . 0 0 2

0 . 6 4 1 . 1 5 1 ± 0 . 0 3 0 . 0 3 - 0 . 0 8 0 . 0 0 8 0 . 9 4 - 1 . 0 9 0 . 0 3 8 0 . 0 5

*Maximum hardness of copper layer is 150 Knoop

N o t e : Recommended annular ring diameter is hole diameter plus . 0 2 0 [ 0 . 5 1 ]

119

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Connectors

AMP ECONOMATE

Connectors provide a

reliable and economical

method for interconnecting

backplane panels, using

either two-sided or multi-

layer PC boards.

Connector housings are fur-

nished unloaded and are

available for post centerline

spacings of: .100 x .200

[2.54 x 5.08] and .156 x .200

[3.96 x 5.08]. The housings

are simply positioned onto

the contacts, after the con-

tacts have been inserted

into the PC board and the

carrier strip removed.

Contacts from Tyco

Electronics feature the

proven and reliable

ACTION PIN contact

design.These press-fit con-

tacts employ two spring

members that compress to

exert force against the

plated through-holes for a

gas-tight connection.

Gold plating of contacts

promotes the electrical

integrity of the connection.

Feed-through posts are also

available for accepting

wrap-type terminations.

These posts also feature the

ACTION PIN contact design

and are supplied in strip

form and stored on reels for

insertion into PC boards.

Performance Specifications

Electrical Characteristics

Contact Resistance:

8 milliohms (max.)

Insulation Resistance:

2,000 megohms (min.)

Continuous Current Rating*:

3 amperes

Physical Characteristics

Card Insertion Force:

16 oz [4.45 N] (max.) per contact pair

Card Extraction Force:

1 oz [0.28 N] (min.) per contact pair

Retention (in PC Board):

7 lb [31.1 N] (min.)

Operating Temperature:

–65°C to +125°C

*Consult Tyco Electronicsengi-

neering when paralleling con-

tacts for power applications.

Important:

Application tooling is

absolutely necessary for

installing contacts and

housings onto PC boards.

See page 126 for applica-

tion tooling.

120

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Connectors (Continued)

.100 x .200 [2.54 x 5.08]

Centerline Spacing

Material and Finish:

Housing—Black glass-filled nylon

Contacts—Copper alloy 725, plated as

follows:

Plating A—Selectively plated .000030

[0.00076] min. gold in contact area,

.000001 [0.00003] min. gold on remain-

der of contact, with entire contact under-

plated .000050 [0.00127] min. nickel

Plating B—Duplex plated .000030

[0.00076] min. gold in contact area,

.000100 [0.00254] min. tin-lead on

posts, with entire contact underplated

.000050 [0.00127] min. nickel

Plating C—Selectively plated .000100

[0.00254] min. gold in contact area,

.000001 [0.00003] min. gold on remain-

der of contact, except .000050 [0.00127]

min. gold for .200 [5.08] from tip of

post, with entire contact underplated

.000050 [0.00127] min. nickel

Related Product Data:

Performance Specifications—

page 119

Card Guides—page 122

ACTION PIN Contact Mounting

Hole Specifications—page 125

Application Tooling—page 126

Technical Documents:

(pages 186, 187):

Product Specification

108-26002

Keying Plugs

Intercontact (Plastic)

Part No. 118982-1

Make-Before-Break Contacts

On-Contact (Plastic)

Part No. 119802-2

No. of Dimensions Housing

Dual Part

Positions A B Numbers

2.734 2.604

25 82.14 78.84 1-117798-4

3.234 3.104

30 82.14 78.84 1-117798-3

3.734 3.604

35 94.84 91.54 1-117798-6

3.834 3.704

36 97.38 94.08 1-117798-7

4.234 4.104

40 107.54 104.24 1-117798-8

5.234 5.104

50 132.94 129.64 1-117798-1

6.234 6.104

60 158.34 155.04 1-117798-2

Note: Other connector sizes can be made available,

consult Tyco Electronics.

. 1 0 0

[ 2 . 5 4 ]

(Card Slot

Length)

Accepts

.054-.071

[1.37-1.80]

PC Boards

Contact

Area

.025

[0.64] Sq.

.100

[2.54]

.025

[0.64] Sq.

.040

[1.02] Ref.

Gold in

Contact

Area

.100

[2.54]

.181

[4.60]

.415

[10.54] .545

[13.84]

.093-.125

[2.36-3.18]

.200

[5.08]

Dimension Contact Part Numbers*

LPlating A Plating B Plating C

.475

12.07 2-117795-4 4-117795-0 —

.702

17.83 1-117795-3 2-117795-6 4-117795-8

*Contacts are strip form, 35,000 per reel.

Dimension Make Before Break Contact Part Numbers*

LPlating A Plating B

.475

12.07 —4-118951-8

.702

17.83 1-118951-4 —

121

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Connectors (Continued)

Keying Plug

Intercontact (Plastic)

Part No. 118982-1

.156 x .200 [3.96 x 5.08]

Centerline Spacing

Material and Finish:

Housing—Black glass-filled nylon

Contacts—Copper alloy 725, plated as

follows:

Plating A—Selectively plated .000030

[0.00076] min. gold in contact area,

.000001 [0.00003] min. gold on remain-

der of contact, with entire contact under-

plated .000050 [0.00127] min. nickel

Plating B—Duplex plated .000030

[0.00076] min. gold in contact area,

.000100 [0.00254] min. tin-lead on

posts, with entire contact underplated

.000050 [0.00127] min. nickel

Related Product Data:

Performance Specifications—

page 119

Card Guides—page 122

ACTION PIN Contact Mounting

Hole Specifications—page 125

Application Tooling—page 126

Technical Documents:

(pages 186, 187):

Product Specification

108-26002

Note: Other connector sizes can be made available,

consult Tyco Electronics.

*Contacts are strip form, 15,000 per reel.

22 Dual Position Housing

Part No. 117296-4

Make-Before-Break Contacts

. 1 5 6

[ 3 . 9 6 ]

3.718

[94.44]

3.588

[91.14]

(Card Slot

Length)

Accepts

.054-.071

[1.37-1.80]

PC Boards

Contact

Area

.025

[0.64] Sq.

.156

[3.96]

.181

[4.60]

.415

[10.54] .545

[13.84]

.093-.125

[2.36-3.18]

.200

[5.08]

Dimension Contact

L Part Numbers*

.475

12.07 117285-7

.702

17.83 117285-8

Make Before Break Contacts

Dimension Plating Part

L Numbers*

.475 B

12.07 1-118778-2

.702 A

17.83 118778-6

.025

[0.64] Sq.

.150

[3.01] Ref.

Gold in

Contact

Area

.150

[3.06]

.702

[17.83]

122

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Card Guides for ECONOMATE Connectors

Material: Black glass-filled nylon

Recommended Mounting Dimensions

Note: A1dimension = Adimension of

ECONOMATE housing plus .310 [7.87].

Hole for

No. 4 Screw

0.45

[11.43] deep .220

[5.59]

.410

[10.41]

.152

[3.86] Dia.

(2 Plcs.)

*Other lengths can be made avail-

able in .500 [12.70] increments

from 1.500 [38.10] to 6.500

[165.10]. Consult Tyco Electronics

for details.

Dimension Card Guide

L* Part Numbers

2.500

63.50 1-117169-3

6.000

152.40 1-117169-3

Housing Dimension

Centerline No. of Dual

Spacing Positions A1

3.544

30 90.02

4.044

35 102.72

4.144

.100 x .200 36 105.26

2.54 x 5.08 4.544

40 115.42

5.544

50 140.82

6.544

60 166.22

.156 x .200 4.028

3.96 x 5.08 22 102.31

Related Product Data:

Mates with all .100 x .200 [2.54 x 5.08]

and .156 x .200 [3.96 x 5.08] centerline

housings

Technical Documents:

(pages 186, 187):

Instruction Sheet 408-9091

123

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Center Carrier Feed-Thru Posts*

.125 [3.18] Centerline,

Wrap Type

Material:

Copper Alloy 725

Finish – Gold plate per MIL-G-45204 or

solder plate over nickel plate per

QQ-N-290 (see table for thicknesses)

Recommended Hole Size:

Non Plated-thru Hole - .0453±.001

[1.15±0.03], 1.15 mm drill

Plated-Thru Hole -.039±.004 [0.99± 0.1 ],

1.15 mm drill

Dimensions Part Numbers

.000100 [0.0025] min. .000030 [0.00076]

A B tin plate over gold plate over

.000050 [0.0013] min. .000050 [0.0013]

nickel plate nickel plate

.703 .548 117311-7 1-117311-0

17.68 13.92

*Use AMP Cut and Transfer Machine for center carrier post insertion. Consult

Tyco Electronics.

D i m e n s i o n s Part Numbers

1) .000001 [0.00003] min.

gold flash over

.000050 [0.0013] min.

A B C nickel plate

2) .000050 [0.0013] min.

gold plate over

.000050 [0.0013] min.

nickel plate

. 3 1 8 . 6 8 7 1 . 0 0 5 —

8 . 0 8 1 7 . 4 5 2 5 . 5 3

. 5 7 8 . 4 6 0 1 . 0 3 8 1 1 8 2 4 3 - 8

1 4 . 6 8 1 1 . 6 8 2 6 . 3 7

. 5 7 8 . 5 5 0 1 . 1 2 8 1 - 1 1 8 2 4 3 - 1

1 4 . 6 8 1 3 . 9 7 2 8 . 6 5

. 3 8 0 . 8 2 3 1 . 2 0 3 —

9 . 6 5 2 0 . 9 0 3 0 . 5 6

.100 [2.54] Centerline,

TERMI-POINT Clip Part

Number 119136-2

Material:

Copper Alloy 725

Finish –

1) Gold plate per MIL-G-45204, .000030

[0.00076] min. thk. over nickel plate per

QQ-N-290, .000050 [0.0013] min. thk.

2) Gold flash per MIL-G-45204, .000001

[0.00003] min. thk. over nickel plate per

QQ-N-290, .000050 [0.0013] min. thk.

Recommended Hole Size:

Non Plated-thru Hole - .0453±.001

[1.15±0.03], 1.15 mm drill

Plated-thru Hole - .039±.004 [0.99± 0.1 ],

1.15 mm drill

.100 [2.54] Centerline,

Wrap Type

Material:

Copper Alloy 725

Finish – Gold plate per MIL-G-45204

over nickel plate per QQ-N-290 (see table

for thicknesses)

Recommended Hole Size:

Non-Plated-thru Hole - .0453±.001

[1.15±0.03], 1.15 mm drill

Plated-thru Hole- .039 ±.004 [0.99 ± 0.1 ],

1.15 mm drill .003

.003

0.08

124

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Connectors (Continued)

50,000 per reel

Part No. 117269-5

Feed-Through Posts .100 [2.54] Centerline Spacing

Material and Finish:

Copper alloy 725, plated as follows:

Plating A—Selectively plated .000030

[0.00076] min. gold in Area (1), .000001

[0.00003] min. gold in Area (2), with

entire post underplated .000050

[0.00127] min. nickel

Plating B—.000030 [0.00076] min.

gold over .000100 [0.00254] min. nickel

on entire post

Plating C—.000050 [0.00127] min.

gold over .000100 [0.00254] min. nickel

on entire post

Plating D—.000100 [0.00254] min.

tin-lead over .000050 [0.00127] min.

nickel on entire post

.150 [3.81] Centerline Spacing

Material and Finish:

Copper alloy 725, selectively plated

.000030 [0.00076] min. gold in Area (1),

.000001 [0.00003] min. gold in Area (2),

with entire post underplated .000050

[0.00127] min. nickel

Dimension Feed-Through Post Part Numbers*

APlating A Plating B Plating C Plating D

.687 1-117249-7

17.45 13-117249-111-117249-2 1-117249-2 6-117249-5

.500

12.70 3-117249-2 — — 5-117249-6

*Posts in strip form, 50,000 per reel.

1Pre-notched to break with 120° bend.

.318

[8.08]

(1)

(2)

.045

[1.14]

.025

[0.64]

.030

[0.76]

Pre-Notch

.025

[0.64]

.100

[2.54]

.318

[8.08]

(1)

(2)

.045

[1.14]

.025

[0.64]

.687

[17.45]

.030

[0.76]

.025

[0.64]

.150

[3.81]

125

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

ECONOMATE Connectors (Continued)

AMP ACTION PIN

Press-Fit Contacts

ACTION PIN contacts provide a reliable press-fit connection.

Localized pressure in the interface area entails oxide

break-through and helps prevent corrosion in the harshest

environments to provide a reliable connection virtually every

time. Also, radial and axial distortion are controlled to meet

today’s standards for multilayer board applications.

PC Board Thickness

ACTION PIN contacts are

designed for use in a variety of

PC board thicknesses. However,

certain ACTION PIN contacts

are to be used in specific ranges

of board thicknesses. To

promote optimum performance,

the recommended board thick-

nesses provided with the con-

nector being used must be

followed.

➀Annular Ring (See Note)

➁Drilled Hole

➂Copper Thickness

➃Tin-Lead Thickness

➄Plated Through-Hole

Mounting Hole Specifications

Connector ACTION PIN Contact Drilled Hole Plating Thicknesses Plated Radial Hole Distortion

No. of Dual Material Through-Hole

Centerline Positions Thickness Diameter➁Copper➂* Tin-Lead➃Diameter➄Average Maximum

.100 x .200 30, 35, 36,

2.54 x 5.08 40, 50, 60 .025 .0453±.001 .001-.003 .0003 .037-.043 Not Not

.156 x .200 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 Specified Specified

3.96 x 5.08 22 Min.

*Maximum hardness of copper layer is 150 Knoop.

Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].

126

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Application Tooling for ECONOMATE Connectors

Available from Tyco

Electronics is a complete

series of ACTION PIN

Assembly Tooling Kits for

ECONOMATE connector

housings and feed-through

posts. Assembly Kit tools

provide the means for

installing housings and con-

tacts onto printed circuit

boards, as well as removing

housings and contacts from

the printed circuit boards.

All tools are available in kits,

or may be purchased

individually.

In many instances, part

number series are listed in

the charts. Specific dash

numbers and detailed infor-

mation on the contacts and

housings are presented on

the respective product

specification pages. For

specific dash numbers and

complete information on

the tooling, contact

Tyco Electronics.

For ECONOMATE Connectors

ACTION PIN Contacts ECONOMATE Housings ACTION PIN Assembly

Pin Part No. of Dual Part Tool NumbersCenterline Length Numbers Positions Numbers Applicator 265902-■

.125 x .125 .702 Carrier Removal Tool 265924-■

3.18 x 3.18 17.83 117793-■15-60 117796-■Housing Assembly Tool 58292-■

Housing Removal Tool 265868-1

Pin Replacement Tool 265871-2

Applicator 265904-■

.100 x .200 .702 Carrier Removal Tool 265924-■

2.54 x 5.08 17.83 117795-■15-60 117798-■Housing Assembly Tool 265879-■

Housing Removal Tool 265868-1

Pin Replacement Tool 265871-2

Applicator 265905-■

.156 x .200 .702 Carrier Removal Tool 265924-■

3.96 x 5.08 17.83 117285-■15-50 117296-■Housing Assembly Tool 265881-■

Housing Removal Tool 265868-1

Pin Replacement Tool 265871-2

Applicator 265906-■

.156 x .200 .475 Carrier Removal Tool 265924-■

3.96 x 5.08 12.07 117285-■15-50 117296-■Housing Assembly Tool 265881-■

Housing Removal Tool 265868-1

Pin Replacement Tool 265871-3

Applicator 266129-■

.100 x .200 .475 Carrier Removal Tool 265924-■

2.54 x 5.08 12.07 117795-■15-60 117798-■Housing Assembly Tool 265879-■

Housing Removal Tool 265868-1

Pin Replacement Tool 265871-3

Applicator 265937-■

.100 .340 Carrier Removal Tool 265924-■

2.54 8.64 117880-■20-60 117879-■Housing Assembly Tool 265962-■

Housing Removal Tool 265868-2

Pin Replacement Tool 1-265871-1

For Feed-Through Posts

ACTION PIN Contacts ACTION PIN Assembly

Pin No. of Part Tool NumbersCenterline Length Positions Numbers

.100 .500-.687 Applicator 265910-■

2.54 12.70-17.45 8-60 117249-■Carrier Removal Tool 265924-■

Pin Replacement Tool 265871-7

.125 .687 Applicator 265911-■

3.18 17.45 8-60 117272-■Carrier Removal Tool 265924-■

Pin Replacement Tool 265871-7

.150 .687 Applicator 265912-■

3.81 17.45 8-50 117269-■Carrier Removal Tool 265924-■

Pin Replacement Tool 265871-7

.150 .365-.475 Applicator 265931-■

3.81 9.27-12.07 8-50 117269-■Carrier Removal Tool 265924-■

Pin Replacement Tool 265871-7

127

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

High Density Press-Fit Card Edge

Product Facts

■High density .050" [1.27]

center spacing.

■Staggered contacts for low

insertion force.

■Designed for multi-layer

.093" [2.36] daughter cards.

■High temperature SMT sol-

der reflow temperatures of

260° for 30 seconds.

■Unique pin geometry allows

for even distribution of

forces reducing axial pin

rotation and preserving per-

pendicularity to the

PCB board.

■Edge and side coining pro-

vides a uniform pin radius

ensuring maximum contact

without "skiving"

the plated hole.

■Full complement of applica-

tion tooling available.

■Recognized under the

Component Program of

Underwriters

Laboratories Inc.,

File No. E60980

■Certified by Canadian

Standards

Association,

File No. LR 49571

High Density (.050" [1.27]

center spacing) Press-Fit

connectors from Tyco

Electronics are designed for

high density backplane or

mid-plane applications.

Compliant pin connectors

from Tyco Electronics meet

or exceed requirements of

current industry standards,

including Bellcore specifica-

tions, which address critical

performance issues such as

hole retention, hole deforma-

tion and environmental per-

f o r m a n c e .

Electrical Characteristics:

Operating Voltage–600VDC (sea

level)

Current Rating –1.5 Amperes

Initial Contact Resistance –

30 milliohms

Environmental

Characteristics:

Operating Temperature –

-55˚C to +125˚C

Temperature Cycling –

MIL-STD-202 method 107

Vibration–

MIL-STD-202, method 204

128

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

.050 [1.27] Centerline For .093 [2.36] Thick Daughter Cards

Material and Finish:

Insulation Resistance—1000

megohms minimum

Contact Retention into PCB—2 lbs.

min.

Insertion Force—10 oz. max.

Mating Force—2 oz. per contact

Housing—High Temp. Glass filled

thermoplastic, UL rating 94V-0

Color—Black

Spring Contact—BeCu

Contact Plating—Palladium Nickel

“A” Spaces • .050 [1.27] = B

.610

[15.49]

.400

[10.15] .332

[8.43]

.132

[3.35]

(Card Slot)

.421

[10.69]

.066 +.005

-.010

[1.68 +.127

-.254

.461

[11.71]

.016

[.41]

.148 [3.76]

.138 [3.51]

]

Note: Dimension E is Connector Mounting PC Hole Pattern.

Section X-X

129

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Ordering Information

No. of Dual Dimensions

Readout TYCO Acquired

Position A B C D E F Part Number Part Number

20 19 0.950 1.040 1.230 1.100 1.010 147668-2 C9D020PF60048

[24.13] [26.42] [31.24] [27.94] [25.65]

30 29 1.450 1.540 1.730 1.600 1.510 147668-3 C9D030PF60048

[36.83] [39.12] [43.94] [40.64] [38.35]

40 39 1.950 2.040 2.230 2.100 2.010 147668-4 C9D040PF60048

[49.53] [51.82] [56.64] [53.34] [51.05]

50 49 2.450 2.540 2.730 2.600 2.510 147668-5 C9D050PF60048

[62.23] [64.52] [69.34] [66.04] [63.75]

60 59 2.950 3.040 3.230 3.100 3.010 147668-6 C9D060PF60048

[74.93] [77.22] [82.04] [78.74] [76.45]

“A” Spaces • .050 [1.27] = B

“A” Spaces at .050 [1.27] = B

.035 [.89] Typ.

.093

[2.36] Thick PC Board

.166

[4.22]

.066

[1.68]

.075

[1.90]

.096 [2.44]

.585

[14.86]

.030

[.76]

.125

[3.17]

.320

[8.13] Min.

.047

R[1.19] Typ.

45° x .025 [.64]

All Around

.150

[3.81]

Section Y-Y

Daughter Board

Configuration

Connector Mounting

PC Hole Pattern

ø .024±.002 (.61±.05)

ø .096 (2.44)

130

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

.100 x .100 [2.54 x 2.54] Centerline Press Fit, with Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum

Contact Retention Into PCB—

5lbs. min. [356 N]

Insertion Force—10 oz. [44.5 N]

max. measured with a .0700 ± .0001

[1.80±.00254] THK polished blade per

MIL-C-21097C

Withdrawal Force—1 oz. min.

[4.54 N] measured with a .0540 ± .0001

[3.37±.000254] THK polished test blade

per MIL-C-21097C after sizing 3 times

with a .0700 ± .0001 [1.80±.00254] THK

blade

Insulator Body—High Temp. Glass

filled thermoplastic, UL rating 94V-O

Color—Black

Spring Contact—Phosphor Bronze

alloy

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—600 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—MIL-STD-202, method

204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

.100

[2.54]

.054 to .071

Accepts [3.37 to 1.80] Thk. PC Board

.100

[2.54]

.100

[2.54]

.100

[2.54]

.100

[2.54]

.550

[13.97]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq. Typ.

.365

[9.27] Ref.

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

131

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Press-Fit Board-To-Board)

Ordering Information

.100 [2.54] Centerline/.100 [2.54] Row-To-Row with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .180 [4.57] (Dim. “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 3 C 1 D 1 8 P F 2 9 1 3 3 C 1 D 1 8 P F 2 9 0 4 3

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 3 C 1 D 2 0 P F 2 9 1 3 3 C 1 D 2 0 P F 2 9 0 4 3

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 3 C 1 D 2 2 P F 2 9 1 3 3 C 1 D 2 2 P F 2 9 0 4 3

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 3 C 1 D 2 5 P F 2 9 1 3 3 C 1 D 2 5 P F 2 9 0 4 3

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 3 C 1 D 2 8 P F 2 9 1 3 3 C 1 D 2 8 P F 2 9 0 4 3

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 3 C 1 D 3 0 P F 2 9 1 3 3 C 1 D 3 0 P F 2 9 0 4 3

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 3 C 1 D 3 5 P F 2 9 1 3 3 C 1 D 3 5 P F 2 9 0 4 3

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 3 C 1 D 3 6 P F 2 9 1 3 3 C 1 D 3 6 P F 2 9 0 4 3

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 3 C 1 D 4 0 P F 2 9 1 3 3 C 1 D 4 0 P F 2 9 0 4 3

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 3 C 1 D 4 3 P F 2 9 1 3 3 C 1 D 4 3 P F 2 9 0 4 3

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 3 C 1 D 4 5 P F 2 9 1 3 3 C 1 D 4 5 P F 2 9 0 4 3

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 3 C 1 D 5 0 P F 2 9 1 3 3 C 1 D 5 0 P F 2 9 0 4 3

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 3 C 1 D 6 0 P F 2 9 1 3 3 C 1 D 6 0 P F 2 9 0 4 3

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

Tail Length .475 [12.07] (Dim. “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 5 C 1 D 1 8 P F 2 9 1 3 5 C 1 D 1 8 P F 2 9 0 4 5

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 5 C 1 D 2 0 P F 2 9 1 3 5 C 1 D 2 0 P F 2 9 0 4 5

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 5 C 1 D 2 2 P F 2 9 1 3 5 C 1 D 2 2 P F 2 9 0 4 5

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 5 C 1 D 2 5 P F 2 9 1 3 5 C 1 D 2 5 P F 2 9 0 4 5

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 5 C 1 D 2 8 P F 2 9 1 3 5 C 1 D 2 8 P F 2 9 0 4 5

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 5 C 1 D 3 0 P F 2 9 1 3 5 C 1 D 3 0 P F 2 9 0 4 5

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 5 C 1 D 3 5 P F 2 9 1 3 5 C 1 D 3 5 P F 2 9 0 4 5

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 5 C 1 D 3 6 P F 2 9 1 3 5 C 1 D 3 6 P F 2 9 0 4 5

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 5 C 1 D 4 0 P F 2 9 1 3 5 C 1 D 4 0 P F 2 9 0 4 5

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 5 C 1 D 4 3 P F 2 9 1 3 5 C 1 D 4 3 P F 2 9 0 4 5

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 5 C 1 D 4 5 P F 2 9 1 3 5 C 1 D 4 5 P F 2 9 0 4 5

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 5 C 1 D 5 0 P F 2 9 1 3 5 C 1 D 5 0 P F 2 9 0 4 5

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 5 C 1 D 6 0 P F 2 9 1 3 5 C 1 D 6 0 P F 2 9 0 4 5

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

132

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.100" [2.54] Centerline / .100" [2.54] Row-to-Row with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .625 [15.88] (Dim. “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 7 C 1 D 1 8 P F 2 9 1 3 7 C 1 D 1 8 P F 2 9 0 4 7

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 7 C 1 D 2 0 P F 2 9 1 3 7 C 1 D 2 0 P F 2 9 0 4 7

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 7 C 1 D 2 2 P F 2 9 1 3 7 C 1 D 2 2 P F 2 9 0 4 7

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 7 C 1 D 2 5 P F 2 9 1 3 7 C 1 D 2 5 P F 2 9 0 4 7

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 7 C 1 D 2 8 P F 2 9 1 3 7 C 1 D 2 8 P F 2 9 0 4 7

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 7 C 1 D 3 0 P F 2 9 1 3 7 C 1 D 3 0 P F 2 9 0 4 7

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 7 C 1 D 3 5 P F 2 9 1 3 7 C 1 D 3 5 P F 2 9 0 4 7

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 7 C 1 D 3 6 P F 2 9 1 3 7 C 1 D 3 6 P F 2 9 0 4 7

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 7 C 1 D 4 0 P F 2 9 1 3 7 C 1 D 4 0 P F 2 9 0 4 7

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 7 C 1 D 4 3 P F 2 9 1 3 7 C 1 D 4 3 P F 2 9 0 4 7

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 7 C 1 D 4 5 P F 2 9 1 3 7 C 1 D 4 5 P F 2 9 0 4 7

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 7 C 1 D 5 0 P F 2 9 1 3 7 C 1 D 5 0 P F 2 9 0 4 7

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 7 C 1 D 6 0 P F 2 9 1 3 7 C 1 D 6 0 P F 2 9 0 4 7

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

133

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.100 x .200 [2.54 x 5.08] Centerline Press-Fit, Full Scoop

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—

5lbs. min. [356 N]

Insertion Force—10 oz. [44.5 N]

max. measured with a .0700 ± .0001

[1.80±.00254] THK polished blade per

MIL-C-21097C

Withdrawal Force—1 oz. min.

[4.5 N] measured with a .0540 ± .0001

[3.37±.00254] THK polished test blade

per MIL-C-21097C after sizing 3 times

with a .0700 ± .0001 [1.80±.00254] THK

blade

Insulator Body—High Temp. Glass

filled thermoplastic, UL rating 94V-O

Color—Black

Spring Contact—Phosphor Bronze

alloy

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties

Operating Voltage—600 VDC

(sea level)

Current Rating—3 Amperes

Contact Resistance—10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

.200

[5.08]

.100

[2.54]

.200

[5.08]

Dim E

.395/.510

[10.03/12.95] Card Slot Depth

.395/.510

[10.03/12.95] Card Slot Depth

.100

[2.54]

.390

[9.91]

.645

[16.38] Ref.

.21

[5.33] Point of Contact

.040±.003

[1.02±.08] Dia.

.020±.010

[.51±.25] Contact Gap

134

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth

Tail Length .670 [17.02] (DIM “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 1 2 W 8 D 1 8 P F 2 9 0 4 2

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 1 2 W 8 D 2 0 P F 2 9 0 4 2

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 1 2 W 8 D 2 2 P F 2 9 0 4 2

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 1 2 W 8 D 2 5 P F 2 9 0 4 2

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 1 2 W 8 D 2 8 P F 2 9 0 4 2

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 1 2 W 8 D 3 0 P F 2 9 0 4 2

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 1 2 W 8 D 3 5 P F 2 9 0 4 2

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 1 2 W 8 D 3 6 P F 2 9 0 4 2

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 1 2 W 8 D 4 0 P F 2 9 0 4 2

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 1 2 W 8 D 4 3 P F 2 9 0 4 2

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 1 2 W 8 D 4 5 P F 2 9 0 4 2

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 1 2 W 8 D 5 0 P F 2 9 0 4 2

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 1 2 W 8 D 6 0 P F 2 9 0 4 2

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

Tail Length .180 [4.57] (DIM “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 1 3 W 8 D 1 8 P F 2 9 0 4 3

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 1 3 W 8 D 2 0 P F 2 9 0 4 3

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 1 3 W 8 D 2 2 P F 2 9 0 4 3

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 1 3 W 8 D 2 5 P F 2 9 0 4 3

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 1 3 W 8 D 2 8 P F 2 9 0 4 3

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 1 3 W 8 D 3 0 P F 2 9 0 4 3

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 1 3 W 8 D 3 5 P F 2 9 0 4 3

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 1 3 W 8 D 3 6 P F 2 9 0 4 3

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 1 3 W 8 D 4 0 P F 2 9 0 4 3

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 1 3 W 8 D 4 3 P F 2 9 0 4 3

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 1 3 W 8 D 4 5 P F 2 9 0 4 3

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 1 3 W 8 D 5 0 P F 2 9 0 4 3

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 1 3 W 8 D 6 0 P F 2 9 0 4 3

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

135

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.100 x .200 [2.54 x 5.08] Centerline, Press-Fit, Full Scoop with Standoffs

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—

5lbs. min. [356 N]

Insertion Force—10 oz. [44.5 N]

max. measured with a .0700 ± .0001

[1.80±.00254] THK polished blade per

MIL-C-21097C

Withdrawal Force—1 oz. min.

[4.5 N] measured with a .0540 ± .0001

[3.37±.00254] THK polished test blade

per MIL-C-21097C after sizing 3 times

with a .0700 ± .0001 [1.80±.00254] THK

blade

Insulator Body—High Temp. Glass

filled thermoplastic, UL rating 94V-O

Color—Black

Spring Contact—Phosphor Bronze

alloy

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—600 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

.200

[5.08]

.100

[2.54]

.200

[5.08]

Dim C

.395/.510

[10.03/12.95] Card Slot Depth

.395/.510

[10.03/12.95] Card Slot Depth

.100

[2.54]

.390

[9.91]

.705

[17.91] Ref.

.21

[5.33] Point of Contact

.040±.003

[1.02±.08] Dia.

.020±.010

[.51±.25 ] Contact Gap

136

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth

Tail Length .670 [17.02] (DIM “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 6 2 W 8 D 1 8 P F 2 9 0 9 2

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 6 2 W 8 D 2 0 P F 2 9 0 9 2

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 6 2 W 8 D 2 2 P F 2 9 0 9 2

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 6 2 W 8 D 2 5 P F 2 9 0 9 2

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 6 2 W 8 D 2 8 P F 2 9 0 9 2

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 6 2 W 8 D 3 0 P F 2 9 0 9 2

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 6 2 W 8 D 3 5 P F 2 9 0 9 2

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 6 2 W 8 D 3 6 P F 2 9 0 9 2

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 6 2 W 8 D 4 0 P F 2 9 0 9 2

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 6 2 W 8 D 4 3 P F 2 9 0 9 2

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 6 2 W 8 D 4 5 P F 2 9 0 9 2

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 6 2 W 8 D 5 0 P F 2 9 0 9 2

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 6 2 W 8 D 6 0 P F 2 9 0 9 2

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

Tail Length .180 [4.57] (DIM “J”)

1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 6 3 W 8 D 1 8 P F 2 9 0 9 3

5 1 . 6 6 4 8 . 3 6 4 3 . 1 8

2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 6 3 W 8 D 2 0 P F 2 9 0 9 3

5 6 . 7 4 5 3 . 4 4 4 8 . 2 6

2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 6 3 W 8 D 2 2 P F 2 9 0 9 3

6 1 . 8 2 5 8 . 5 2 5 3 . 3 4

2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 6 3 W 8 D 2 5 P F 2 9 0 9 3

6 9 . 4 4 6 6 . 1 4 6 0 . 9 6

2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 6 3 W 8 D 2 8 P F 2 9 0 9 3

7 7 . 0 6 7 3 . 7 6 6 8 . 5 8

3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 6 3 W 8 D 3 0 P F 2 9 0 9 3

8 2 . 1 4 7 8 . 8 4 7 3 . 6 6

3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 6 3 W 8 D 3 5 P F 2 9 0 9 3

9 4 . 8 4 9 1 . 5 4 8 6 . 3 6

3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 6 3 W 8 D 3 6 P F 2 9 0 9 3

9 7 . 3 8 9 4 . 0 8 8 8 . 9 0

4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 6 3 W 8 D 4 0 P F 2 9 0 9 3

1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6

4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 6 3 W 8 D 4 3 P F 2 9 0 9 3

1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8

4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 6 3 W 8 D 4 5 P F 2 9 0 9 3

1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6

5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 6 3 W 8 D 5 0 P F 2 9 0 9 3

1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6

6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 6 3 W 8 D 6 0 P F 2 9 0 9 3

1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6

137

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.100 x .200 [2.54 x 5.08] Centerline, Press-Fit without Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—5 lbs.

[356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—600 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.200

[5.08]

.054 to .071

Accepts [3.37 to 1.80] Thk. PC Board

.100

[2.54]

.200

[5.08]

.100

[2.54]

.100

[2.54]

.550

[13.97]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq. Typ.

.365

[9.27] Ref.

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

138

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.100" [2.54] Centerline / .200" [5.08] Row-to-Row without Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .670 [17.02] (“J”)

60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 3 2 C 8 D 0 6 P F 2 9 1 4 2 C 8 D 0 6 P F 2 9 0 2 2

2 1 . 8 4 1 7 . 7 8 1 2 . 7 0

1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 3 2 C 8 D 1 0 P F 2 9 1 4 2 C 8 D 1 0 P F 2 9 0 2 2

3 2 . 0 0 2 7 . 9 4 2 2 . 8 6

1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 3 2 C 8 D 1 2 P F 2 9 1 4 2 C 8 D 1 2 P F 2 9 0 2 2

3 7 . 0 8 3 3 . 0 2 2 7 . 9 4

1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 3 2 C 8 D 1 5 P F 2 9 1 4 2 C 8 D 1 5 P F 2 9 0 2 2

4 4 . 7 0 4 0 . 6 4 3 5 . 5 6

2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 3 2 C 8 D 2 0 P F 2 9 1 4 2 C 8 D 2 0 P F 2 9 0 2 2

5 7 . 4 0 5 3 . 3 4 4 8 . 2 6

2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 3 2 C 8 D 2 2 P F 2 9 1 4 2 C 8 D 2 2 P F 2 9 0 2 2

6 2 . 4 8 5 8 . 4 2 5 3 . 3 4

2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 3 2 C 8 D 2 5 P F 2 9 1 4 2 C 8 D 2 5 P F 2 9 0 2 2

7 0 . 1 0 6 6 . 0 4 6 0 . 9 6

2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 3 2 C 8 D 2 8 P F 2 9 1 4 2 C 8 D 2 8 P F 2 9 0 2 2

7 7 . 7 2 7 3 . 6 6 6 8 . 5 8

3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 3 2 C 8 D 3 0 P F 2 9 1 4 2 C 8 D 3 0 P F 2 9 0 2 2

8 2 . 8 0 7 8 . 7 4 7 3 . 6 6

3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 3 2 C 8 D 3 1 P F 2 9 1 4 2 C 8 D 3 1 P F 2 9 0 2 2

8 5 . 3 4 8 1 . 2 8 7 6 . 2 0

3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 3 2 C 8 D 3 5 P F 2 9 1 4 2 C 8 D 3 5 P F 2 9 0 2 2

9 5 . 5 0 9 1 . 4 4 8 6 . 3 6

3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 3 2 C 8 D 3 6 P F 2 9 1 4 2 C 8 D 3 6 P F 2 9 0 2 2

9 8 . 0 4 9 3 . 9 8 8 8 . 9 0

4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 3 2 C 8 D 4 0 P F 2 9 1 4 2 C 8 D 4 0 P F 2 9 0 2 2

1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6

4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 3 2 C 8 D 4 3 P F 2 9 1 4 2 C 8 D 4 3 P F 2 9 0 2 2

1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8

5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 3 2 C 8 D 5 0 P F 2 9 1 4 2 C 8 D 5 0 P F 2 9 0 2 2

1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6

6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 3 2 C 8 D 6 0 P F 2 9 1 4 2 C 8 D 6 0 P F 2 9 0 2 2

1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6

Tail Length .180 [4.57] (“J”)

60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 3 3 C 8 D 0 6 P F 2 9 1 4 3 C 8 D 0 6 P F 2 9 0 2 3

2 1 . 8 4 1 7 . 7 8 1 2 . 7 0

1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 3 3 C 8 D 1 0 P F 2 9 1 4 3 C 8 D 1 0 P F 2 9 0 2 3

3 2 . 0 0 2 7 . 9 4 2 2 . 8 6

1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 3 3 C 8 D 1 2 P F 2 9 1 4 3 C 8 D 1 2 P F 2 9 0 2 3

3 7 . 0 8 3 3 . 0 2 2 7 . 9 4

1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 3 3 C 8 D 1 5 P F 2 9 1 4 3 C 8 D 1 5 P F 2 9 0 2 3

4 4 . 7 0 4 0 . 6 4 3 5 . 5 6

2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 3 3 C 8 D 2 0 P F 2 9 1 4 3 C 8 D 2 0 P F 2 9 0 2 3

5 7 . 4 0 5 3 . 3 4 4 8 . 2 6

2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 3 3 C 8 D 2 2 P F 2 9 1 4 3 C 8 D 2 2 P F 2 9 0 2 3

6 2 . 4 8 5 8 . 4 2 5 3 . 3 4

2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 3 3 C 8 D 2 5 P F 2 9 1 4 3 C 8 D 2 5 P F 2 9 0 2 3

7 0 . 1 0 6 6 . 0 4 6 0 . 9 6

2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 3 3 C 8 D 2 8 P F 2 9 1 4 3 C 8 D 2 8 P F 2 9 0 2 3

7 7 . 7 2 7 3 . 6 6 6 8 . 5 8

3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 3 3 C 8 D 3 0 P F 2 9 1 4 3 C 8 D 3 0 P F 2 9 0 2 3

8 2 . 8 0 7 8 . 7 4 7 3 . 6 6

3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 3 3 C 8 D 3 1 P F 2 9 1 4 3 C 8 D 3 1 P F 2 9 0 2 3

8 5 . 3 4 8 1 . 2 8 7 6 . 2 0

3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 3 3 C 8 D 3 5 P F 2 9 1 4 3 C 8 D 3 5 P F 2 9 0 2 3

9 5 . 5 0 9 1 . 4 4 8 6 . 3 6

3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 3 3 C 8 D 3 6 P F 2 9 1 4 3 C 8 D 3 6 P F 2 9 0 2 3

9 8 . 0 4 9 3 . 9 8 8 8 . 9 0

4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 3 3 C 8 D 4 0 P F 2 9 1 4 3 C 8 D 4 0 P F 2 9 0 2 3

1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6

4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 3 3 C 8 D 4 3 P F 2 9 1 4 3 C 8 D 4 3 P F 2 9 0 2 3

1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8

5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 3 3 C 8 D 5 0 P F 2 9 1 4 3 C 8 D 5 0 P F 2 9 0 2 3

1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6

6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 3 3 C 8 D 6 0 P F 2 9 1 4 3 C 8 D 6 0 P F 2 9 0 2 3

1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6

139

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.100 x .200 [2.54 x 5.08] Centerline, Press-Fit with Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—5 lbs.

[356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—600 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.200

[5.08]

.054 to .071

Accepts [1.37 to 1.80] Thk. PC Board

.100

[2.54]

.200

[5.08]

.100

[2.54]

.100

[2.54]

.610

[15.49]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq.

.365

[9.27] Ref.

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

140

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering InformationOrdering Information

.100 [2.54] Center-to-Center/.200 [5.08] Row-To-Row with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .670 [17.02] (dim “J”)

60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 1 2 C 8 D 0 6 P F 2 9 1 3 2 C 8 D 0 6 P F 2 9 0 4 2

2 1 . 8 4 1 7 . 7 8 1 2 . 7 0

1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 1 2 C 8 D 1 0 P F 2 9 1 3 2 C 8 D 1 0 P F 2 9 0 4 2

3 2 . 0 0 2 7 . 9 4 2 2 . 8 6

1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 1 2 C 8 D 1 2 P F 2 9 1 3 2 C 8 D 1 2 P F 2 9 0 4 2

3 7 . 0 8 3 3 . 0 2 2 7 . 9 4

1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 1 2 C 8 D 1 5 P F 2 9 1 3 2 C 8 D 1 5 P F 2 9 0 4 2

4 4 . 7 0 4 0 . 6 4 3 5 . 5 6

2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 1 2 C 8 D 2 0 P F 2 9 1 3 2 C 8 D 2 0 P F 2 9 0 4 2

5 7 . 4 0 5 3 . 3 4 4 8 . 2 6

2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 1 2 C 8 D 2 2 P F 2 9 1 3 2 C 8 D 2 2 P F 2 9 0 4 2

6 2 . 4 8 5 8 . 4 2 5 3 . 3 4

2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 1 2 C 8 D 2 5 P F 2 9 1 3 2 C 8 D 2 5 P F 2 9 0 4 2

7 0 . 1 0 6 6 . 0 4 6 0 . 9 6

2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 1 2 C 8 D 2 8 P F 2 9 1 3 2 C 8 D 2 8 P F 2 9 0 4 2

7 7 . 7 2 7 3 . 6 6 6 8 . 5 8

3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 1 2 C 8 D 3 0 P F 2 9 1 3 2 C 8 D 3 0 P F 2 9 0 4 2

8 2 . 8 0 7 8 . 7 4 7 3 . 6 6

3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 1 2 C 8 D 3 1 P F 2 9 1 3 2 C 8 D 3 1 P F 2 9 0 4 2

8 5 . 3 4 8 1 . 2 8 7 6 . 2 0

3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 1 2 C 8 D 3 5 P F 2 9 1 3 2 C 8 D 3 5 P F 2 9 0 4 2

9 5 . 5 0 9 1 . 4 4 8 6 . 3 6

3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 1 2 C 8 D 3 6 P F 2 9 1 3 2 C 8 D 3 6 P F 2 9 0 4 2

9 8 . 0 4 9 3 . 9 8 8 8 . 9 0

4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 1 2 C 8 D 4 0 P F 2 9 1 3 2 C 8 D 4 0 P F 2 9 0 4 2

1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6

4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 1 2 C 8 D 4 3 P F 2 9 1 3 2 C 8 D 4 3 P F 2 9 0 4 2

1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8

5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 1 2 C 8 D 5 0 P F 2 9 1 3 2 C 8 D 5 0 P F 2 9 0 4 2

1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6

6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 1 2 C 8 D 6 0 P F 2 9 1 3 2 C 8 D 6 0 P F 2 9 0 4 2

1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6

Tail Length .180 [4.57] (dim “J”)

60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 1 3 C 8 D 0 6 P F 2 9 1 3 3 C 8 D 0 6 P F 2 9 0 4 3

2 1 . 8 4 1 7 . 7 8 1 2 . 7 0

1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 1 3 C 8 D 1 0 P F 2 9 1 3 3 C 8 D 1 0 P F 2 9 0 4 3

3 2 . 0 0 2 7 . 9 4 2 2 . 8 6

1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 1 3 C 8 D 1 2 P F 2 9 1 3 3 C 8 D 1 2 P F 2 9 0 4 3

3 7 . 0 8 3 3 . 0 2 2 7 . 9 4

1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 1 3 C 8 D 1 5 P F 2 9 1 3 3 C 8 D 1 5 P F 2 9 0 4 3

4 4 . 7 0 4 0 . 6 4 3 5 . 5 6

2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 1 3 C 8 D 2 0 P F 2 9 1 3 3 C 8 D 2 0 P F 2 9 0 4 3

5 7 . 4 0 5 3 . 3 4 4 8 . 2 6

2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 1 3 C 8 D 2 2 P F 2 9 1 3 3 C 8 D 2 2 P F 2 9 0 4 3

6 2 . 4 8 5 8 . 4 2 5 3 . 3 4

2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 1 3 C 8 D 2 5 P F 2 9 1 3 3 C 8 D 2 5 P F 2 9 0 4 3

7 0 . 1 0 6 6 . 0 4 6 0 . 9 6

2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 1 3 C 8 D 2 8 P F 2 9 1 3 3 C 8 D 2 8 P F 2 9 0 4 3

7 7 . 7 2 7 3 . 6 6 6 8 . 5 8

3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 1 3 C 8 D 3 0 P F 2 9 1 3 3 C 8 D 3 0 P F 2 9 0 4 3

8 2 . 8 0 7 8 . 7 4 7 3 . 6 6

3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 1 3 C 8 D 3 1 P F 2 9 1 3 3 C 8 D 3 1 P F 2 9 0 4 3

8 5 . 3 4 8 1 . 2 8 7 6 . 2 0

3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 1 3 C 8 D 3 5 P F 2 9 1 3 3 C 8 D 3 5 P F 2 9 0 4 3

9 5 . 5 0 9 1 . 4 4 8 6 . 3 6

3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 1 3 C 8 D 3 6 P F 2 9 1 3 3 C 8 D 3 6 P F 2 9 0 4 3

9 8 . 0 4 9 3 . 9 8 8 8 . 9 0

4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 1 3 C 8 D 4 0 P F 2 9 1 3 3 C 8 D 4 0 P F 2 9 0 4 3

1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6

4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 1 3 C 8 D 4 3 P F 2 9 1 3 3 C 8 D 4 3 P F 2 9 0 4 3

1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8

5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 1 3 C 8 D 5 0 P F 2 9 1 3 3 C 8 D 5 0 P F 2 9 0 4 3

1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6

6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 1 3 C 8 D 6 0 P F 2 9 1 3 3 C 8 D 6 0 P F 2 9 0 4 3

1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6

141

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.125 x .250 [3.18 x 6.35] Centerline without Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—5 lbs.

[356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—1000 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.250

[6.35]

.054 to .071

Accepts [1.37 to 1.80] Thk. PC Board

.125

[3.18]

.250

[6.35]

.125

[3.18]

.125

[3.18]

.550

[13.97]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq. Typ.

.365

[9.27]

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

142

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.125 [3.18] Centerline /.250 [6.35] Row-to-Row without Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .670 [17.02] (DIM “J”)

61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 3 2 C 7 D 0 6 P F 2 9 1 4 2 C 7 D 0 6 P F 2 9 0 2 2

2 6 . 2 9 2 2 . 2 3 1 5 . 8 8

1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 3 2 C 7 D 1 0 P F 2 9 1 4 2 C 7 D 1 0 P F 2 9 0 2 2

3 8 . 9 9 3 4 . 9 3 2 8 . 5 8

1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 3 2 C 7 D 1 2 P F 2 9 1 4 2 C 7 D 1 2 P F 2 9 0 2 2

4 5 . 3 4 4 1 . 2 8 3 4 . 9 3

1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 3 2 C 7 D 1 5 P F 2 9 1 4 2 C 7 D 1 5 P F 2 9 0 2 2

5 4 . 8 6 5 0 . 8 0 4 4 . 4 5

1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 3 2 C 7 D 1 8 P F 2 9 1 4 2 C 7 D 1 8 P F 2 9 0 2 2

6 4 . 3 9 6 0 . 3 3 5 3 . 9 8

2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 3 2 C 7 D 2 0 P F 2 9 1 4 2 C 7 D 2 0 P F 2 9 0 2 2

7 0 . 7 4 6 6 . 6 8 6 0 . 3 3

2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 3 2 C 7 D 2 2 P F 2 9 1 4 2 C 7 D 2 2 P F 2 9 0 2 2

7 7 . 0 9 7 3 . 0 3 6 6 . 6 8

2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 3 2 C 7 D 2 5 P F 2 9 1 4 2 C 7 D 2 5 P F 2 9 0 2 2

8 6 . 6 1 8 2 . 5 5 7 6 . 2 0

2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 3 2 C 7 D 2 8 P F 2 9 1 4 2 C 7 D 2 8 P F 2 9 0 2 2

9 6 . 1 4 9 2 . 0 8 8 5 . 7 3

3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 3 2 C 7 D 3 0 P F 2 9 1 4 2 C 7 D 3 0 P F 2 9 0 2 2

1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8

3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 3 2 C 7 D 3 1 P F 2 9 1 4 2 C 7 D 3 1 P F 2 9 0 2 2

1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5

3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 3 2 C 7 D 3 5 P F 2 9 1 4 2 C 7 D 3 5 P F 2 9 0 2 2

1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5

3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 3 2 C 7 D 3 6 P F 2 9 1 4 2 C 7 D 3 6 P F 2 9 0 2 2

1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3

4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 3 2 C 7 D 4 0 P F 2 9 1 4 2 C 7 D 4 0 P F 2 9 0 2 2

1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3

4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 3 2 C 7 D 4 3 P F 2 9 1 4 2 C 7 D 4 3 P F 2 9 0 2 2

1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5

5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 3 2 C 7 D 5 0 P F 2 9 1 4 2 C 7 D 5 0 P F 2 9 0 2 2

1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8

Tail Length .180 [4.57] (DIM “J”)

61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 3 3 C 7 D 0 6 P F 2 9 1 4 3 C 7 D 0 6 P F 2 9 0 2 3

2 6 . 2 9 2 2 . 2 3 1 5 . 8 8

1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 3 3 C 7 D 1 0 P F 2 9 1 4 3 C 7 D 1 0 P F 2 9 0 2 3

3 8 . 9 9 3 4 . 9 3 2 8 . 5 8

1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 3 3 C 7 D 1 2 P F 2 9 1 4 3 C 7 D 1 2 P F 2 9 0 2 3

4 5 . 3 4 4 1 . 2 8 3 4 . 9 3

1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 3 3 C 7 D 1 5 P F 2 9 1 4 3 C 7 D 1 5 P F 2 9 0 2 3

5 4 . 8 6 5 0 . 8 0 4 4 . 4 5

1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 3 3 C 7 D 1 8 P F 2 9 1 4 3 C 7 D 1 8 P F 2 9 0 2 3

6 4 . 3 9 6 0 . 3 3 5 3 . 9 8

2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 3 3 C 7 D 2 0 P F 2 9 1 4 3 C 7 D 2 0 P F 2 9 0 2 3

7 0 . 7 4 6 6 . 6 8 6 0 . 3 3

2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 3 3 C 7 D 2 2 P F 2 9 1 4 3 C 7 D 2 2 P F 2 9 0 2 3

7 7 . 0 9 7 3 . 0 3 6 6 . 6 8

2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 3 3 C 7 D 2 5 P F 2 9 1 4 3 C 7 D 2 5 P F 2 9 0 2 3

8 6 . 6 1 8 2 . 5 5 7 6 . 2 0

2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 3 3 C 7 D 2 8 P F 2 9 1 4 3 C 7 D 2 8 P F 2 9 0 2 3

9 6 . 1 4 9 2 . 0 8 8 5 . 7 3

3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 3 3 C 7 D 3 0 P F 2 9 1 4 3 C 7 D 3 0 P F 2 9 0 2 3

1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8

3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 3 3 C 7 D 3 1 P F 2 9 1 4 3 C 7 D 3 1 P F 2 9 0 2 3

1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5

3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 3 3 C 7 D 3 5 P F 2 9 1 4 3 C 7 D 3 5 P F 2 9 0 2 3

1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5

3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 3 3 C 7 D 3 6 P F 2 9 1 4 3 C 7 D 3 6 P F 2 9 0 2 3

1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3

4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 3 3 C 7 D 4 0 P F 2 9 1 4 3 C 7 D 4 0 P F 2 9 0 2 3

1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3

4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 3 3 C 7 D 4 3 P F 2 9 1 4 3 C 7 D 4 3 P F 2 9 0 2 3

1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5

5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 3 3 C 7 D 5 0 P F 2 9 1 4 3 C 7 D 5 0 P F 2 9 0 2 3

1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8

143

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.125 x .250 [3.18 x 6.35] Centerline with Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—5 lbs.

[356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—1000 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.200

[5.08]

.054 to .071

Accepts [1.37 to 1.80] Thk. PC Board

.125

[3.18]

.250

[6.35]

.125

[3.18]

.125

[3.18]

.550

[13.97]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq. Typ.

.365

[9.27]

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

144

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.125 [3.18] Centerline /.250 [6.35] Row-to-Row with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

Tail Length .670 [17.02] (DIM “J”)

61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 1 2 C 7 D 0 6 P F 2 9 1 3 2 C 7 D 0 6 P F 2 9 0 4 2

2 6 . 2 9 2 2 . 2 3 1 5 . 8 8

1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 1 2 C 7 D 1 0 P F 2 9 1 3 2 C 7 D 1 0 P F 2 9 0 4 2

3 8 . 9 9 3 4 . 9 3 2 8 . 5 8

1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 1 2 C 7 D 1 2 P F 2 9 1 3 2 C 7 D 1 2 P F 2 9 0 4 2

4 5 . 3 4 4 1 . 2 8 3 4 . 9 3

1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 1 2 C 7 D 1 5 P F 2 9 1 3 2 C 7 D 1 5 P F 2 9 0 4 2

5 4 . 8 6 5 0 . 8 0 4 4 . 4 5

1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 1 2 C 7 D 1 8 P F 2 9 1 3 2 C 7 D 1 8 P F 2 9 0 4 2

6 4 . 3 9 6 0 . 3 3 5 3 . 9 8

2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 1 2 C 7 D 2 0 P F 2 9 1 3 2 C 7 D 2 0 P F 2 9 0 4 2

7 0 . 7 4 6 6 . 6 8 6 0 . 3 3

2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 1 2 C 7 D 2 2 P F 2 9 1 3 2 C 7 D 2 2 P F 2 9 0 4 2

7 7 . 0 9 7 3 . 0 3 6 6 . 6 8

2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 1 2 C 7 D 2 5 P F 2 9 1 3 2 C 7 D 2 5 P F 2 9 0 4 2

8 6 . 6 1 8 2 . 5 5 7 6 . 2 0

2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 1 2 C 7 D 2 8 P F 2 9 1 3 2 C 7 D 2 8 P F 2 9 0 4 2

9 6 . 1 4 9 2 . 0 8 8 5 . 7 3

3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 1 2 C 7 D 3 0 P F 2 9 1 3 2 C 7 D 3 0 P F 2 9 0 4 2

1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8

3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 1 2 C 7 D 3 1 P F 2 9 1 3 2 C 7 D 3 1 P F 2 9 0 4 2

1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5

3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 1 2 C 7 D 3 5 P F 2 9 1 3 2 C 7 D 3 5 P F 2 9 0 4 2

1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5

3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 1 2 C 7 D 3 6 P F 2 9 1 3 2 C 7 D 3 6 P F 2 9 0 4 2

1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3

4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 1 2 C 7 D 4 0 P F 2 9 1 3 2 C 7 D 4 0 P F 2 9 0 4 2

1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3

4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 1 2 C 7 D 4 3 P F 2 9 1 3 2 C 7 D 4 3 P F 2 9 0 4 2

1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5

5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 1 2 C 7 D 5 0 P F 2 9 1 3 2 C 7 D 5 0 P F 2 9 0 4 2

1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8

Tail Length .180 [4.57] (DIM “J”)

61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 1 3 C 7 D 0 6 P F 2 9 1 3 3 C 7 D 0 6 P F 2 9 0 4 3

2 6 . 2 9 2 2 . 2 3 1 5 . 8 8

1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 1 3 C 7 D 1 0 P F 2 9 1 3 3 C 7 D 1 0 P F 2 9 0 4 3

3 8 . 9 9 3 4 . 9 3 2 8 . 5 8

1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 1 3 C 7 D 1 2 P F 2 9 1 3 3 C 7 D 1 2 P F 2 9 0 4 3

4 5 . 3 4 4 1 . 2 8 3 4 . 9 3

1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 1 3 C 7 D 1 5 P F 2 9 1 3 3 C 7 D 1 5 P F 2 9 0 4 3

5 4 . 8 6 5 0 . 8 0 4 4 . 4 5

1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 1 3 C 7 D 1 8 P F 2 9 1 3 3 C 7 D 1 8 P F 2 9 0 4 3

6 4 . 3 9 6 0 . 3 3 5 3 . 9 8

2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 1 3 C 7 D 2 0 P F 2 9 1 3 3 C 7 D 2 0 P F 2 9 0 4 3

7 0 . 7 4 6 6 . 6 8 6 0 . 3 3

2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 1 3 C 7 D 2 2 P F 2 9 1 3 3 C 7 D 2 2 P F 2 9 0 4 3

7 7 . 0 9 7 3 . 0 3 6 6 . 6 8

2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 1 3 C 7 D 2 5 P F 2 9 1 3 3 C 7 D 2 5 P F 2 9 0 4 3

8 6 . 6 1 8 2 . 5 5 7 6 . 2 0

2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 1 3 C 7 D 2 8 P F 2 9 1 3 3 C 7 D 2 8 P F 2 9 0 4 3

9 6 . 1 4 9 2 . 0 8 8 5 . 7 3

3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 1 3 C 7 D 3 0 P F 2 9 1 3 3 C 7 D 3 0 P F 2 9 0 4 3

1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8

3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 1 3 C 7 D 3 1 P F 2 9 1 3 3 C 7 D 3 1 P F 2 9 0 4 3

1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5

3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 1 3 C 7 D 3 5 P F 2 9 1 3 3 C 7 D 3 5 P F 2 9 0 4 3

1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5

3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 1 3 C 7 D 3 6 P F 2 9 1 3 3 C 7 D 3 6 P F 2 9 0 4 3

1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3

4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 1 3 C 7 D 4 0 P F 2 9 1 3 3 C 7 D 4 0 P F 2 9 0 4 3

1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3

4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 1 3 C 7 D 4 3 P F 2 9 1 3 3 C 7 D 4 3 P F 2 9 0 4 3

1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5

5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 1 3 C 7 D 5 0 P F 2 9 1 3 3 C 7 D 5 0 P F 2 9 0 4 3

1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8

NOTE: Optional stacking designs are available (consult Tyco Electronics).

145

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.156 x .200 [3.18 x 5.08] Centerline without Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—

5 lbs. [356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—1500 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.200

[5.08]

.054 to .071

Accepts [1.37 to 1.80] Thk. PC Board

.156

[3.96]

.156

[3.96]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.156

[3.96]

.550

[13.97]

.025

[.64] Sq. Typ.

.365

[9.27] Ref.

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

.200

[5.08]

146

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.156 [3.18] Centerline/.200 [5.08] Row-to-Row without Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth

.670 [17.02] Tail Length (DIM “J”)

61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 3 2 C 6 D 0 6 P F 2 9 1 4 2 C 6 D 0 6 P F 2 9 0 2 2

3 1 . 0 1 2 7 . 9 4 1 9 . 8 1

1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 3 2 C 6 D 1 0 P F 2 9 1 4 2 C 6 D 1 0 P F 2 9 0 2 2

4 6 . 8 6 4 3 . 7 9 3 5 . 6 6

1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 3 2 C 6 D 1 2 P F 2 9 1 4 2 C 6 D 1 2 P F 2 9 0 2 2

5 4 . 7 9 5 1 . 7 1 4 3 . 5 9

1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 3 2 C 6 D 1 5 P F 2 9 1 4 2 C 6 D 1 5 P F 2 9 0 2 2

6 6 . 6 8 6 3 . 6 0 5 5 . 4 7

1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 3 2 C 6 D 1 8 P F 2 9 1 4 2 C 6 D 1 8 P F 2 9 0 2 2

7 8 . 5 6 7 5 . 4 9 6 7 . 3 6

2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 3 2 C 6 D 2 0 P F 2 9 1 4 2 C 6 D 2 0 P F 2 9 0 2 2

8 6 . 4 9 8 3 . 4 1 7 5 . 2 9

2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 3 2 C 6 D 2 2 P F 2 9 1 4 2 C 6 D 2 2 P F 2 9 0 2 2

9 4 . 4 1 9 1 . 3 4 8 3 . 2 1

2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 3 2 C 6 D 2 5 P F 2 9 1 4 2 C 6 D 2 5 P F 2 9 0 2 2

1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0

2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 3 2 C 6 D 2 8 P F 2 9 1 4 2 C 6 D 2 8 P F 2 9 0 2 2

1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8

3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 3 2 C 6 D 3 0 P F 2 9 1 4 2 C 6 D 3 0 P F 2 9 0 2 2

1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1

3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 3 2 C 6 D 3 1 P F 2 9 1 4 2 C 6 D 3 1 P F 2 9 0 2 2

1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7

3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 3 2 C 6 D 3 5 P F 2 9 1 4 2 C 6 D 3 5 P F 2 9 0 2 2

1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2

3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 3 2 C 6 D 3 6 P F 2 9 1 4 2 C 6 D 3 6 P F 2 9 0 2 2

1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8

4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 3 2 C 6 D 4 0 P F 2 9 1 4 2 C 6 D 4 0 P F 2 9 0 2 2

1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6

4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 3 2 C 6 D 4 3 P F 2 9 1 4 2 C 6 D 4 3 P F 2 9 0 2 2

1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2

.180 [4.57] Tail Length (DIM “J”)

61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 3 3 C 6 D 0 6 P F 2 9 1 4 3 C 6 D 0 6 P F 2 9 0 2 3

3 1 . 0 1 2 7 . 9 4 1 9 . 8 1

1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 3 3 C 6 D 1 0 P F 2 9 1 4 3 C 6 D 1 0 P F 2 9 0 2 3

4 6 . 8 6 4 3 . 7 9 3 5 . 6 6

1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 3 3 C 6 D 1 2 P F 2 9 1 4 3 C 6 D 1 2 P F 2 9 0 2 3

5 4 . 7 9 5 1 . 7 1 4 3 . 5 9

1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 3 3 C 6 D 1 5 P F 2 9 1 4 3 C 6 D 1 5 P F 2 9 0 2 3

6 6 . 6 8 6 3 . 6 0 5 5 . 4 7

1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 3 3 C 6 D 1 8 P F 2 9 1 4 3 C 6 D 1 8 P F 2 9 0 2 3

7 8 . 5 6 7 5 . 4 9 6 7 . 3 6

2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 3 3 C 6 D 2 0 P F 2 9 1 4 3 C 6 D 2 0 P F 2 9 0 2 3

8 6 . 4 9 8 3 . 4 1 7 5 . 2 9

2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 3 3 C 6 D 2 2 P F 2 9 1 4 3 C 6 D 2 2 P F 2 9 0 2 3

9 4 . 4 1 9 1 . 3 4 8 3 . 2 1

2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 3 3 C 6 D 2 5 P F 2 9 1 4 3 C 6 D 2 5 P F 2 9 0 2 3

1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0

2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 3 3 C 6 D 2 8 P F 2 9 1 4 3 C 6 D 2 8 P F 2 9 0 2 3

1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8

3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 3 3 C 6 D 3 0 P F 2 9 1 4 3 C 6 D 3 0 P F 2 9 0 2 3

1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1

3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 3 3 C 6 D 3 1 P F 2 9 1 4 3 C 6 D 3 1 P F 2 9 0 2 3

1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7

3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 3 3 C 6 D 3 5 P F 2 9 1 4 3 C 6 D 3 5 P F 2 9 0 2 3

1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2

3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 3 3 C 6 D 3 6 P F 2 9 1 4 3 C 6 D 3 6 P F 2 9 0 2 3

1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8

4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 3 3 C 6 D 4 0 P F 2 9 1 4 3 C 6 D 4 0 P F 2 9 0 2 3

1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6

4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 3 3 C 6 D 4 3 P F 2 9 1 4 3 C 6 D 4 3 P F 2 9 0 2 3

1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2

147

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

.156 x .200 [3.18 x 5.08] Centerline with Standoffs

Product Facts

■Recognized under the

Component Program

of Underwriters

Laboratories Inc.,

File No. E60980

■Certified

by Canadian

Standards

Association,

File No. LR49571

Physical Properties:

Insulation Resistance—

5000 megohms minimum.

Contact Retention Into PCB—5 lbs.

[356 N]

Insertion/Withdrawal Force—

8 oz./2 oz. [35.6 N/ 8.9 N] average

contact pair using .0620 [1.57] steel

blade.

Insulator Body—Glass filled

thermoplastic, UL rating 94V-O

Color—Black

Contacts—High strength copper alloy.

Contact Plating—.000050 [0.00127]

nickel underplate with .000030

[0.00076] gold in the mating area,

tin/lead on tails, .000100 [0.00254]

minimum

Electrical Properties:

Operating Voltage—1500 VDC

(sea level)

Current Rating—3 Amperes

Initial Contact Resistance—

10 milliohms

Environmental Properties:

Operating Temperature—

-55˚C to +125˚C

Temperature Cycling—

MIL-STD-202 method 107

Vibration—

MIL-STD-202, method 204

Application Tooling:

Insertion Tool—page 150

Related Product Data:

Daughter Card Edge Pattern—

page 57

Note: Open ends and open/closed

ends are available. Consult Tyco

E l e c t r o n i c s .

.200

[5.08]

.054 to .071

Accepts [1.37 to 1.80] Thk. PC Board

.156

[3.96]

.200

[5.08]

.156

[3.96]

.156

[3.96]

.610

[15.49]

Dim C

.020

[.51] Contact Gap

Card Slot

Depth

.300 [7.62]

.350 [8.89]

.415 [10.54]

.040±.003

[1.02±.08] Dia.

.025

[.64] Sq. Typ.

.365

[9.27] Ref.

. 1 2 0±. 0 0 3

[3.05±.25]

Point of

Contact

148

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Ordering Information

.156 [3.18] Centerline/.200 [5.08] Row-to-Row with Standoffs

No. of Dual D i m e n s i o n s Acquired Part Numbers

Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth

.670 [17.02] Tail Length (DIM “J”)

61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 1 2 C 6 D 0 6 P F 2 9 1 3 2 C 6 D 0 6 P F 2 9 0 4 2

3 1 . 0 1 2 7 . 9 4 1 9 . 8 1

1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 1 2 C 6 D 1 0 P F 2 9 1 3 2 C 6 D 1 0 P F 2 9 0 4 2

4 6 . 8 6 4 3 . 7 9 3 5 . 6 6

1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 1 2 C 6 D 1 2 P F 2 9 1 3 2 C 6 D 1 2 P F 2 9 0 4 2

5 4 . 7 9 5 1 . 7 1 4 3 . 5 9

1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 1 2 C 6 D 1 5 P F 2 9 1 3 2 C 6 D 1 5 P F 2 9 0 4 2

6 6 . 6 8 6 3 . 6 0 5 5 . 4 7

1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 1 2 C 6 D 1 8 P F 2 9 1 3 2 C 6 D 1 8 P F 2 9 0 4 2

7 8 . 5 6 7 5 . 4 9 6 7 . 3 6

2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 1 2 C 6 D 2 0 P F 2 9 1 3 2 C 6 D 2 0 P F 2 9 0 4 2

8 6 . 4 9 8 3 . 4 1 7 5 . 2 9

2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 1 2 C 6 D 2 2 P F 2 9 1 3 2 C 6 D 2 2 P F 2 9 0 4 2

9 4 . 4 1 9 1 . 3 4 8 3 . 2 1

2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 1 2 C 6 D 2 5 P F 2 9 1 3 2 C 6 D 2 5 P F 2 9 0 4 2

1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0

2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 1 2 C 6 D 2 8 P F 2 9 1 3 2 C 6 D 2 8 P F 2 9 0 4 2

1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8

3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 1 2 C 6 D 3 0 P F 2 9 1 3 2 C 6 D 3 0 P F 2 9 0 4 2

1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1

3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 1 2 C 6 D 3 1 P F 2 9 1 3 2 C 6 D 3 1 P F 2 9 0 4 2

1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7

3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 1 2 C 6 D 3 5 P F 2 9 1 3 2 C 6 D 3 5 P F 2 9 0 4 2

1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2

3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 1 2 C 6 D 3 6 P F 2 9 1 3 2 C 6 D 3 6 P F 2 9 0 4 2

1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8

4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 1 2 C 6 D 4 0 P F 2 9 1 3 2 C 6 D 4 0 P F 2 9 0 4 2

1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6

4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 1 2 C 6 D 4 3 P F 2 9 1 3 2 C 6 D 4 3 P F 2 9 0 4 2

1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2

.180 [4.57] Tail Length (DIM “J”)

61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 1 3 C 6 D 0 6 P F 2 9 1 3 3 C 6 D 0 6 P F 2 9 0 4 3

3 1 . 0 1 2 7 . 9 4 1 9 . 8 1

1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 1 3 C 6 D 1 0 P F 2 9 1 3 3 C 6 D 1 0 P F 2 9 0 4 3

4 6 . 8 6 4 3 . 7 9 3 5 . 6 6

1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 1 3 C 6 D 1 2 P F 2 9 1 3 3 C 6 D 1 2 P F 2 9 0 4 3

5 4 . 7 9 5 1 . 7 1 4 3 . 5 9

1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 1 3 C 6 D 1 5 P F 2 9 1 3 3 C 6 D 1 5 P F 2 9 0 4 3

6 6 . 6 8 6 3 . 6 0 5 5 . 4 7

1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 1 3 C 6 D 1 8 P F 2 9 1 3 3 C 6 D 1 8 P F 2 9 0 4 3

7 8 . 5 6 7 5 . 4 9 6 7 . 3 6

2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 1 3 C 6 D 2 0 P F 2 9 1 3 3 C 6 D 2 0 P F 2 9 0 4 3

8 6 . 4 9 8 3 . 4 1 7 5 . 2 9

2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 1 3 C 6 D 2 2 P F 2 9 1 3 3 C 6 D 2 2 P F 2 9 0 4 3

9 4 . 4 1 9 1 . 3 4 8 3 . 2 1

2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 1 3 C 6 D 2 5 P F 2 9 1 3 3 C 6 D 2 5 P F 2 9 0 4 3

1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0

2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 1 3 C 6 D 2 8 P F 2 9 1 3 3 C 6 D 2 8 P F 2 9 0 4 3

1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8

3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 1 3 C 6 D 3 0 P F 2 9 1 3 3 C 6 D 3 0 P F 2 9 0 4 3

1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1

3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 1 3 C 6 D 3 1 P F 2 9 1 3 3 C 6 D 3 1 P F 2 9 0 4 3

1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7

3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 1 3 C 6 D 3 5 P F 2 9 1 3 3 C 6 D 3 5 P F 2 9 0 4 3

1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2

3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 1 3 C 6 D 3 6 P F 2 9 1 3 3 C 6 D 3 6 P F 2 9 0 4 3

1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8

4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 1 3 C 6 D 4 0 P F 2 9 1 3 3 C 6 D 4 0 P F 2 9 0 4 3

1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6

4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 1 3 C 6 D 4 3 P F 2 9 1 3 3 C 6 D 4 3 P F 2 9 0 4 3

1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2

149

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Press-Fit Application Tooling

BMEP 1K/2K Servo Electric

Press

• 1000 or 2000 lb force [4.5

or 9 kN]

• 12” [305 mm] throat depth

• Compact footprint – 16” x

24” [406 x 610 mm]

• Force resolution of

approximately 1 lb [4.4 N]

for delicate press applica-

tions.

Tyco Electronics offers a

complete line of servo-elec-

tric driven presses for the

application of press-fit con-

nectors. Each system fea-

tures a PC controlled servo

electric drive for precise

application and monitoring

of force, speed, and press

height. The entire process

is data driven to provide

flexible programming and

automatic set-up. SPC

analysis is provided for

each connector pressed to

assure the quality of every

application. BMEP 3T/5T Benchtop Electric

Servo Press

• 3 or 5 tons force [27 or 44

kN]

• 18” x 24” [460 x 610 mm]

PCB capacity

• Compact footprint – 24” x

48” [610 x 1220 mm]

• Midrange force and board

size capacity in a bench-

top unit.

MEP 6T/12 T Manual Electric

Servo Press

• 6 or 12 tons force [53 or

107 kN]

• 24” x 36” [610 x 914 mm]

PCB capacity

• Self-contained, portable

unit

• Compact, manual unit

capable of handling large

boards and high force

applications.

Automatic Pick, Place and

Press (AP3)

• 8 tons force [71 kN]

• 18” x 30” [457 x 762 mm]

PCB capacity

• SMEMA compatible unit

for automatic pick, place

and press of connectors

and odd-from compo-

nents.

• Vision system for pin

inspection prior to place-

ment.

150

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Press-Fit Card Edge Insertion Tools

Ordering Information

Center-to Connector Max. No. Of Tool Part Replacement Blade

Center Prefix Positions Number Part Number

Acquired P/N TYCO Acquired P/N Tyco

.100 x .100 C1 70 98336 3-1437266-5 98293 1437274-1

2.54 x 2.54

.100 x .100 C1 100 98341 — 98293 1437274-1

2.54 x 2.54

.156 x .200 C6 43 98231 1-1437266-1 98206 1437266-8

3.96 x 5.08

.125 x .250 C7 50 98230 1-1437266-0 98206 1437266-8

3.18 x 6.35

.100 x .200 C8 70 98224 1-1437266-9 98206 1437266-8

2.54 x 5.08

.100 x .200 W8 70 98236 1-1490560-1 98238 1490563-12.54 x 5.08

(Full Scoop)

.100 x .200 W8 35 98236 1-1490560-2 98238 1490563-12.54 x 5.08

(Full Scoop)

151

Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514

Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967

Card Edge Connectors

(Board-to-Board, Wire-to-Board)

Press-Fit Card Edge Removal Tool Kits

Description

Removal tool kits include:

impact tools, removal tips

for tail lengths ranging from

.180 in. [4.57] to .680 in.

[17.27] Kits for .100" x .200"

[2.54 x 5.08] Series Card

Edge connectors include

the insertion tip.

Acquired Tyco

Center x Row Prefix Kit Number Kit Number

.156 x .200 C6 9818002 1437266-3

3.96 x 5.08

.125 x .250 C7 9818002 1437266-3

3.18 x 6.35

.100 x .200 C8 9818002 1437266-3

2.54 x 5.08

.100 x .100 C1 9818004 1437266-4

2.54 x 2.54

.100 x .200 W8 9818005 1437266-5

2.54 x 5.08

Wide Full Scoop

R e p l a c e m e n t T y c o

I t e m D e s c r i p t i o n Applies to Kit No. P a r t P a r t

N o . 9 8 1 8 0 0 1 9 8 1 8 0 0 1 9 8 1 8 0 0 3 9 8 1 8 0 0 4 9 8 1 8 0 0 5 N u m b e r N u m b e r

1Impact Tool √√√√√9 8 2 0 4 0 1 1 4 3 7 2 6 6 - 7

2Removal Tip - .180 [4.57] Tail √√√√√9 8 2 0 3 0 1 1 4 3 7 2 6 6 - 6

3Removal Tip - . 3 7 8 / . 4 7 5 T a i l √√√√9 8 2 0 3 0 2 1 4 3 7 2 6 0 - 4

9 . 6 0 / 1 2 . 0 7

4Removal Tip - . 6 7 0 / . 6 8 0 T a i l √√√√9 8 2 0 3 0 3 —

1 7 . 0 2 / 1 7 . 2 7

6Insertion Tip - C6, 7 & 8 PF √9 8 3 6 7 0 1 3 - 1 4 3 7 2 6 6 - 9

1 0 Removal Tip - . 5 5 0 / . 6 2 5 T a i l √9 8 2 0 3 0 5 1 4 3 7 2 6 0 - 5

1 3 . 9 7 / 1 5 . 8 8

1 1 Insertion Tip - C1 Series PF √9 8 3 6 3 0 1 1 4 3 7 2 6 0 - 6

1 2 Insertion Tip - W8 Series PF √9 8 3 6 7 0 2 1 4 3 7 2 6 0 - 7

Ordering Information