R Specifications and Ordering Information 170133 FieldMonitorTM Internal 3300 Proximitor Module Description The 170133 Internal 3300 Proximitor(R) Module is a dual Proximitor(R) module that will work with any standard 3300 series 5 mm or 8 mm probe in 5 m, 9 m, and 14 m system lengths. This module's dual internal Proximitor(R) sensors eliminate the need for external Proximitor(R) sensors, and allows direct connection of up to two proximity probes and their associated extension cables. Specifications The following specifications apply between 18C and 27C (64F to 80F) with a Bently Nevada supplied AISI 4140 steel target. Typical is defined as 90% of the devices built meeting the specification. The calibration range is 250 m (10 mil) to 2250 m (90 mil), (approximately -1 to - 17 Volt.) Note: Operation outside the specified limits may result in false readings and/or loss of machine monitoring. System BNC Part Number 141481-01 Revision B, March, 2001 Incremental Scale Factor (ISF): Typically 7.87 mV/m (200.0 mV/mil), 6 1/2% including interchangeability error when measured in increments of 0.25 mm (10 mils) over the linear range. Frequency response (at 50 mils gap): 0 to 12.5 K Hz (750,000 cpm), -3dB Minimum Target Size: 15.2 mm (0.6 inch) diameter (flat target). Shaft Diameter: Minimum: 50.8 mm (2 inches). Recommended minimum: 76.2 mm (3 inches). With XY probes in the same plane, shaft diameters smaller than 50.8 mm (2 inches) will experience electrical noise due to crosstalk. Consult Performance Specification 155687 for the amount that the scale factor will increase for shaft diameters Page 1 of 6 smaller than 76.2 mm (3 inches). Proximitor(R) Sensor Interchangeability error Weight: 320 g (0.71 lb) Storage Temperature: -40C to +85C (-40F to +185F) Operating Temperature: -34C to +85C (-30F to +185F) Relative Humidity: 100% condensing non-submerged from 7C to 85C (45F to 185F) when connectors are protected. Indication of faults: The output will go to within 1.0 volt (typically 0.7 volts) of common if a short or open circuit occurs in an extension cable or probe. Hazardous Area Approvals: (see ordering information) Standard Approvals: CSA/NRTL/C: Exn, Class 1, Division 2, Groups A, B, C, and D T4 @ Ta = 70C. LCIE Zone 2 EEx nA IIC, T4 @ Ta = 70C. ATEX Multi-Agency Approvals: CSA/NRTL/C: Exn Class 1, Division 2, Groups A, B, C, and D T4 @ Ta = 70C. LCIE Zone 2 EEx nA IIC, T4 @ Ta = 70C. LCIE EEx nA [ia] ia IIC, T4 @ Ta = 70. ATEX Probe dc resistance (nominal) (RPROBE): connector Recommended minimum bend radius: 25.4 mm (1.00 in) Probe Temperature Range: -51C to +177C (-60F to +351F) for 3300 XL probes; -35 C to +177C (-31F to +351F) for non-XL probes. Relative Humidity: 100% condensing nonsubmerged from 2C to 100C (35F to 212F) when connectors are protected. Cables Interchangeability error dc resistance, nominal Center conductor (RCORE): 0.222 /m (0.067 /ft) Shield (RJACKET): 0.066 /m (0.020 /ft) Capacitance: 69.9 pF/m (21.3 pF/ft) typical Minimum bend radius: 25.4 mm (1.0 in) Operating Temperature: -51C to +177C (-60F to +350F) Storage Temperature: -51 C to +177C (-60F to +350F) Relative Humidity: 100% condensing nonsubmerged from 2C to 100C (35F to 212F) when connectors are protected. 7.3 + 0.28 /m (7.3 + 0.087 /ft) Connector-to-connector torque Ordering Information Recommended torque: See table below Maximum torque: 0.565*N*m (5 in*lb) Connector Type Two 3300 XL gold "click" type connectors One non-XL stainless steel connector and one 3300 XL BNC Part Number 141481-01 Revision B, March, 2001 Tightening Instructions Finger tight Finger tight plus 1/8 turn using pliers Note: Order the shortest system length required for your installation. Shorter systems are more temperature stable throughout the operating temperature range. 3300 Internal Dual Proximitor(R) Module 170133-XXX-XX Option Description A: Total Length Option 050 090 140 Internal 3300 Dual 5-metre Proximitor(R) Sensor Internal 3300 Dual 9-metre Proximitor(R) Sensor Internal 3300 Dual 14-metre Page 2 of 6 connector protectors Proximitor(R) Sensor B: Hazardous Area Approval 0 0 Division 2/Zone 2 0 5 Multi-Agency C: Agency Approval Option 0 0 Not required 0 5 Multiple Approvals Use the 05 option in the 1701/06 Isolator Terminal Base 142238-120-BXX-CXX Note: Use this cable with a 2-metre 3300 or 3300 XL probe with the 170133-140-XX 3300 14-metre Internal Proximitor(R) Module. Option Descriptions Accessories B: Connector and Cable Option 0 0 Standard cable 0 1 Armored cable 0 2 Standard cable with connector protectors 0 3 Armored cable with connector protectors 1 0 FluidLoc(R) cable 1 1 Armored FluidLoc(R) cable 1 2 FluidLoc(R) cable with connector protectors 1 3 Armored FluidLoc(R) cable with connector protectors C: Agency Approval Option 0 0 Not required 0 5 Multiple Approvals For 3300 5 mm and 3300 XL 8 mm proximity probe information, refer to Bently Nevada part numbers 141194-01 and 141605-01 for specifications and ordering information. 3300 XL series extension cable The 5-metre and 9-metre 170133 3300 series internal Proximitor(R) Sensor uses standard 330130 extension cables. For the 14-metre 170133 system, use a 3300 XL 2-metre probe with the 142238 12-metre extension cable: 3300 XL Extension Cable 330130-AXXX-BXX-CXX Note: Make sure that the extension cable length and the probe length, when added together, equal the Proximitor(R) Sensor total length. Option Descriptions A: Cable Length Option 030 050 040 045 070 075 080 085 3.0 metres (9.8 feet) 3.5 metres (11.5 feet) 4.0 metres (13.1 feet) 4.5 metres (14.8 feet) 7.0 metres (22.9 feet) 7.5 metres (24.6 feet) 8.0 metres (26.2 feet) 8.5 metres (27.9 feet) B: Connector and Cable Option 0 0 Standard cable 0 1 Armored cable 0 2 Standard cable with connector protectors 0 3 Armored cable with connector protectors 1 0 FluidLoc(R) cable 1 1 Armored FluidLoc(R) cable 1 2 FluidLoc(R) cable with connector protectors 1 3 Armored FluidLoc(R) cable with 1999, 2001 Bently Nevada Corporation used in this document are registered marks of Bently Nevada Corporation ModbusTM is a trademark of Schneider Electric ControlNetTM is a trademark of ControlNet International BNC Part Number 141481-01 Revision B, March, 2001 Page 3 of 6 DeviceNetTM is a trademark of the Open DeviceNet Vendor Association (ODVA) ProfibusTM is a trademark of the PROFIBUS User Organization Dimensional Drawing Dimensions are in millimetres (inches) BNC Part Number 141481-01 Revision B, March, 2001 Page 4 of 6 Performance Graphs 170133 Internal 3300 Proximitor(R) Module DSL ERROR IN MILS Referenced to 200 MV/MIL 10 5 0 -5 -10 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 25 deg C (77 deg F) 90 100 110 120 130 140 20% ISF ERROR Referenced to 200 MV/MIL 15% 10% 5% 0% -5% -10% -15% -20% 90 100 110 120 130 140 100 110 120 130 85 deg C (185 deg F) 140 -24 -22 -20 OUTPUT (VOLTS) -18 -16 -14 -12 -10 -8 -6 -4 -2 0 60 70 80 90 70 deg C (158 deg F) Figure 1: 170133 System Performance Graphs 5-metre Proximitor and 4-metre (13.1 feet) cable at high temperature BNC Part Number 141481-01 Revision B, March, 2001 Page 5 of 6 DSL ERROR IN MILS Referenced to 200 MV/MIL 10 5 0 -5 -10 0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 20% ISF ERROR Referenced to 200 MV/MIL 15% 10% 5% 0% -5% -10% -15% -20% 100 110 120 130 140 100 110 120 130 140 -24 -22 -20 OUTPUT (VOLTS) -18 -16 -14 -12 -10 -8 -6 -4 -2 0 25 deg C (77 deg F) -20 deg C (-4 deg F) -35 deg C (-31 deg F) Figure 2: 170133 System Performance Graphs 5-metre Proximitor and 4-metre (13.1 feet) cable at low temperature BNC Part Number 141481-01 Revision B, March, 2001 Page 6 of 6