Printed in USA 08/05 P/N 03467 rev. E
VALU-BEAM® 912 Series
AC- and DC-powered sensors with solid-state outputs
WARNING . . . Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A
sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner
Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
Features
• Choose models for 10 to 30V dc or 24 to 250V ac operation.
• DC models have bipolar solid-state outputs: one NPN (sinking) and one PNP
(sourcing).
• AC models have an SPST solid-state output rated for up to 3/4 amp with simple
2-wire hookup.
• All models have a rear panel sensitivity adjustment and light/dark operate switch.
• DC models include Banner’s Alignment Indicating Device (AID™) system.
• Choose models with integral 2 m (6.5') cable or Mini-style QD (quick-disconnect)
connector; 9 m (30') cables are also available.
Opposed Mode Emitter (E) and Receiver (R) Models
Models Range Cable* Supply
Voltage
Output
Type Excess Gain Beam Pattern
SMA91E
SMA91EQD
60 m
(200')
2 m (6.5')
3-Pin Mini QD 10-250V ac/dc –
SM91R
SM91RQD
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A91R
SM2A91RQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
SMA91ESR
SMA91ESRQD
3 m
(10')
2 m (6.5')
3-Pin Mini QD 10-250V ac/dc –
SM91RSR
SM91RSRQD
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A91RSR
SM2A91RSRQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
* 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SMA91E W/30).
A model with a QD connector requires a mating cable; see page 7.
Infrared, 880 nm
M
g
M
g
M
g
M
g
EGCSMSMAOPPEPS
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-!%3-2
3-!%3-!2
/PPOSED-ODE
M
g
M
g
M
g
M
g
EGCSMESSMAESOPPEPS
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-!%323-232
3-!%323-!232
/PPOSED-ODE
M
g
M
g
M
g
M
g
M
g
MM
MM
MM
MM
MM
MM
$)34!.#%
3-!%323-232
3-!%323-!232
/PPOSED-ODE
M
g
M
g
M
g
M
g
M
g
MM
MM
MM
MM
MM
MM
$)34!.#%
3-!%3-2
3-!%3-!2
/PPOSED-ODE
Effective Beam: 3.5 mm
Effective Beam: 13 mm
VALU-BEAM® Sensors – 912 Series
2 P/N 03467 rev. E
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Retroreflective Mode Models
†
Retroreflective range is specified using one model BRT-3 retroreflector (3" diameter). Actual sensing range may be more or less than specified,
depending upon the efficiency and reflective area of the retroreflector used.
††Use polarized models when shiny objects will be sensed.
P
Visible Red, 650 nm
Non-Polarized Polarized
Models Range†Cable* Supply
Voltage
Output
Type Excess Gain Beam Pattern
Non-Polarized
SM912LV
SM912LVQD 0.15
to 9 m
(6" to
30')
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912LV
SM2A912LVQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
Polarized††
SM912LVAG
SM912LVAGQD 0.3 to
4.5 m
(1' to
15')
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912LVAG
SM2A912LVAGQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
M
g
M
g
M
g
M
g
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-,6
3-!,6
2ETROREFLECTIVE-ODE
7ITH"242EFLECTOR
EGCSMLVSMALVEPS
M
g
M
g
M
g
M
g
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-,6!'
3-!,6!'
2ETROREFLECTIVE-ODE
7ITH"242EFLECTOR
EGCSMLVAGSMALVAGEPS
M
g
M
g
M
g
M
g
M
g
MM
MM
MM
MM
MM
MM
$)34!.#%
3-,6!'3-!,6!'
2ETROREFLECTIVE-ODE
7ITH"242EFLECTOR
M
g
M
g
M
g
M
g
M
g
MM
MM
MM
MM
MM
MM
$)34!.#%
3-,63-!,6
2ETROREFLECTIVE-ODE
7ITH"242EFLECTOR
Diffuse Mode Models
Models Range†Cable* Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Performance based on 90% reflectance white test card
SM912D
SM912DQD
760 mm
(30")
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912D
SM2A912DQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
SM912DSR
SM912DSRQD
380 mm
(15")
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912DSR
SM2A912DSRQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
Infrared, 880 nm
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-$
3-!$
$IFFUSE-ODE
EGCSMDSMADEPS
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-$32
3-!$32
$IFFUSE-ODE
EGCSMDSRSMADSREPS
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-$323-!$32
$IFFUSE-ODE
"0SM$32SMA$32DIFEPS
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-$3-!$
$IFFUSE-ODE
"0SM$SMA$EPS
P/N 03467 rev. E 3
VALU-BEAM® Sensors – 912 Series
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Convergent Mode Models
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SMA91EF W/30).
A model with a QD connector requires a mating cable; see page 7.
Visible Red or Infrared; see below
Glass Fiber Optic Individual Emitter or Receiver Models
Models Range Cable* Supply Voltage Output Type Excess Gain Beam Pattern
SMA91EF
SMA91EFQD
Range
varies
with
fiber
used
2 m (6.5')
3-Pin Mini QD 10-250V ac/dc –
SM91RF
SM91RFQD
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A91RF
SM2A91RFQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
Infrared, 880 nm
M
g
M
g
M
g
M
g
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-!%&3-2&
3-!%&3-!2&
/PPOSED-ODE
)43&IBERS
7,,ENSES
)43&IBERS
7,&,ENSES
M
g
M
g
M
g
M
g
M
g
MM
MM
MM
MM
MM
MM
$)34!.#%
3-!%&3-2&
3-!%&3-!2&
/PPOSED-ODE
)43&IBERS
7ITH,LENSES
)43&IBERS
7ITH,&LENSES
Use where the separation between emitting and receiving fibers is more than a few feet,
or where it is inconvenient to run both fibers from a single sensor. Watertight o-ring-
sealed sensor/fiber interface.
Models Range Cable* Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Performance based on 90% reflectance white test card
Visible Red 650 nm
SM912CV
SM912CVQD
38 mm
(1.5")
Spot
Size
at Focus:
1.5 mm
(0.06")
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912CV
SM2A912CVQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
Infrared 880 nm
SM912C
SM912CQD
38 mm
(1.5")
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912C
SM2A912CQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-#6
3-!#6
#ONVERGENT-ODE
EGCSMCVEPS
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-#
3-!#
#ONVERGENT-ODE
EGCSMCSMACEPS
"0SM#SMA#EPS
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-#3-!#
#ONVERGENT-ODE
"0SM#6SMA#6EPS
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-#63-!#6
#ONVERGENT-ODE
VALU-BEAM® Sensors – 912 Series
4 P/N 03467 rev. E
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SM912F W/30).
A model with a QD connector requires a mating cable; see page 7.
Dimensions
Cabled Models QD Models
Convergent Sensing Mode
(model suffix LVAG, C and CV)
Glass Fiber Optic
(model suffix F, EF and RF)
Rear View
Glass Fiber Optic Models
Models Range Cable* Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Performance based on 90% reflectance white test card
SM912F
SM912FQD
Range
varies
with
sensing
mode
and fiber
optics
used.
2 m (6.5')
4-Pin Mini QD 10-30V dc Bipolar
NPN/PNP
SM2A912F
SM2A912FQD
2 m (6.5')
3-Pin Mini QD 24-250V ac
SPST SCR
Solid-state
2-Wire
Infrared, 880 nm
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-&
3-!&
/PPOSED-ODE
)43&IBERS
)43&IBERS
MM
MM
MM
MM
%
8
#
%
3
3
'
!
)
.
$)34!.#%
3-&
3-!&
$IFFUSE-ODE
EGCSM&SMA&DIFFEPS
"43&IBER
"43&IBER
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-&3-!&
$IFFUSE-ODE
"43"43
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
MM
$)34!.#%
3-&3-!&
/PPOSED-ODE
)43 )43
36.6 mm
(1.44") 35.6 mm
(1.40")
LED Indicator
Lens Centerline
50.8 mm
(2.00")
12.7 mm
(0.50")
M30 x 1.5 External Thread
1/2" - 14 NPSM Internal Thread
39.1 mm
(1.54")
Hex Nut Supplied
39.6 mm
(1.56")
26.7 mm
(1.05")
Mini-style
Quick-disconnect
M30 x 1.5 Thread
Hex Nut Supplied
,IGHT$ARK/PERATE3ELECT
,/#7$/##7
3ENSITIVITY#ONTROL
4URN#7TO)NCREASE
MM
MM
3CREW#LEARANCE
MM
MM
./4%#ONTROLPOTENTIOMETERSARE
BEHINDCOVERSCREWSREMOVE
SCREWSTOACCESSCONTROLS
42.2 mm
(1.66")
Fiber Port Centerline
Watertight o-ring-sealed sensor/fiber interface.
P/N 03467 rev. E 5
VALU-BEAM® Sensors – 912 Series
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Other DC Models – Cabled
DC Hookups
Supply Voltage and Current 10 to 30V dc at 20 mA maximum, exclusive of load (except for SMA91E, ESR and EF emitters, which operate
from 10 to 250V ac or dc, 10 mA max.)
Supply Protection Circuitry Protected against reverse polarity and transient voltages
Output Configuration Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor
Output Rating 250 mA continuous, each output
Off-state leakage current: less than 10 microamps
Output saturation voltage: (PNP output) less than 1 volt at 10 mA and less than 2 volts at 250 mA
Output saturation voltage: (NPN output) less than 200 millivolts at 10 mA and less than 1 volt at 250 mA
Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short-circuit of outputs
Output Response Time Receivers only: 8 milliseconds ON and 4 milliseconds OFF, independent of signal strength.
All other models: 4 milliseconds ON/OFF
NOTE: 100 millisecond delay on power-up; outputs do not conduct during this delay.
Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs: 1.0 millisecond
Retro, Diffuse, Convergent and Glass Fiber Optic Models: 1.3 milliseconds
Adjustments Light/Dark Operate select switch and Sensitivity control potentiometer, both located at rear of sensor
Indicators Alignment Indicating Device (AID™) lights a top-mounted red LED indicator whenever the sensor sees a
“light” condition; its pulse rate is proportional to the light signal strength (the stronger the signal, the faster
the pulse rate).
Model SMA91E and SM91ESR emitters: visible-red “tracer beam” indicates “Power ON” and enables
line-of-sight alignment.
Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel
hardware
Environmetal Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66
Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables or 4-pin Mini-style quick-disconnect (QD) fitting available.
NOTE: Opposed-mode emitters use 3-pin Mini-style QD fitting. See page 7.
Operating Conditions Temperature: -20° to +70° C (-4° to +158° F)
Maximum relative humidity: 90% at 50° C (non-condensing)
Certifications
Specifications – DC Models
Other DC Models – QD
(4-Pin Mini-Style)
Emitters – Cabled
Emitters – QD
(3-Pin Mini-Style)
4-Pin Mini-Style Pinout
(Cable Connector Shown)
3-Pin Mini-Style Pinout
(Cable Connector Shown)
bn
wh
bu
+
–
bk Load
Load
10-30V dc
912 dc VB-standard w/cable.eps
bn
wh
bu
+
–
bk Load
Load
10-30V dc
912 dc VB-standard w/qd.eps
bn
bu
+
–
ac/dc vb-emitter w/cable.eps
10-250V ac/dc
bn
bk
bu
ac/dc vb-emitter w/qd.eps
10-250V ac/dc
+
–
Black Wire
Blue Wire
Brown Wire
White Wire
Brown Wire
Blue Wire
Black Wire
VALU-BEAM® Sensors – 912 Series
6 P/N 03467 rev. E
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Other AC Models – Cabled
AC Hookups
Supply Voltage and Current 24 to 250V ac (50/60 Hz), except for SMA91E, ESR and EF emitters, which operate from 10 to 250V ac or dc
Supply Protection Circuitry Protected against transient voltages
Output Configuration SPST SCR solid-state relay with either normally closed or normally open contact
(light/dark operate selectable); 2-wire hookup
Output Rating Minimum load current 10 mA, max. steady-state load capability 750 mA to 50° C ambient (122° F),
500 mA to 70° C ambient (158° F)
Inrush capability: 4 amps for 1 second (non-repetitive)
Off-state leakage: current less than 1.7 mA rms
On-state voltage drop: ≤ 5 volts rms at 750 mA load, ≤ 10 volts rms at 15 mA load
Output Protection Circuitry Protected against false pulse on power-up
Output Response Time Receivers only: 8 milliseconds 0N and 4 milliseconds OFF, independent of signal strength
All other models: 8 milliseconds ON and OFF
OFF time does not include load response of up to 1/2 ac cycle (8.3 milliseconds).
Response time specification of the load should be considered when total response time is important.
NOTE: 300 millisecond delay on power-up; outputs do not conduct during this delay.
Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs: 1.0 millisecond
Retro, Diffuse, Convergent and Glass Fiber Optic: 2.6 milliseconds
Adjustments Light/Dark Operate select switch and Sensitivity control potentiometer, both located at rear of sensor
Indicators Top-mounted red LED indicator lights when output is conducting.
Model SMA91E and SM91ESR emitters: visible-red “tracer beam” indicates “Power ON” and enables line-of-
sight alignment.
Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel
hardware
Environmetal Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66
Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables or 3-pin Mini-style (QD) fitting available. See page 7.
Operating Conditions Temperature: -20° to +70° C (-4° to +158° F) Maximum relative humidity: 90% at 50° C (non-condensing)
Application Notes i) 912 Series ac sensors can be destroyed from overload conditions.
ii) Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state
voltage of the sensor will interfere with proper operation of the load.
iii) The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in
series or parallel with mechanical switch contacts.
Certifications
Specifications – AC Models
Other AC Models – QD
(3-Pin Mini-Style)
Emitters – Cabled
Emitters – QD
(3-Pin Mini-Style)
3-Pin Mini-Style Pinout
(Cable Connector Shown)
bn
bu Load
24-250V ac
912 ac VB-NO w/cable.eps
bn
bk
bu 24-250V ac
Load
912 ac VB-NO w/qd.eps
+
–
bn
bu
+
–
ac/dc vb-emitter w/cable.eps
10-250V ac/dc
Brown Wire
Blue Wire
Black Wire
bn
bk
bu
ac/dc vb-emitter w/qd.eps
10-250V ac/dc
+
–
P/N 03467 rev. E 7
VALU-BEAM® Sensors – 912 Series
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Retroreflective Targets
Extension Cables (without connectors)
The following cables are available for extending the length of existing sensor cable. These are 30 m (100') lengths of VALU-BEAM cable.
This cable may be spliced to existing cable. Connectors, if used, must be customer-supplied.
Model Type Used With:
EC312-100 4-conductor SM912 Series dc sensors
EC312A-100 2-conductor For all emitters and SM2A912 Series ac sensors
Cabling Accessories
Accessories
Quick-Disconnect Cables
Cable: PVC jacket, polyurethane connector body; nylon coupling nut
Conductors: 18 AWG, high-flex stranded, PVC insulation, gold plated contacts
Temperature: -40° to +80° C (-40° to +176° F)
Style Model Length Dimensions Pinout (Female View)
3-Pin
Mini-style
Female, Straight
MBCC-306
MBCC-312
MBCC-330
2 m (6.5’)
4 m (12’)
9 m (30’)
4-Pin
Mini-style
Female, Straight
MBCC-406
MBCC-412
MBCC-430
2 m (6.5’)
4 m (12’)
9 m (30’)
Brown Wire
Blue Wire
Black Wire
7/8-16UN-2B
ø 28 mm max.
(1.1")
61 mm max.
(2.4")
Black Wire
Blue Wire
Brown Wire
White Wire
Model Description
AC-6
PVC-6
RF1-2NPS
2 m (6.5') armored cable jacket
2 m (6.5') flexible PVC tubing (not for QD models)
Compression fitting for attaching armored cable or PVC tubing
I.D. 5/16"; O.D. 7/16"
I.D. 1/4"; O.D. 3/8"
–
HF1-2NPS
• Flexible black nylon cable protector
• Includes a neoprene gland that compresses around the VALU-BEAM cable to provide
an additional seal against moisture
• Resistant to gasoline, alcohol, oil, grease, solvents and weak acids
• Working temperature range of -30° to +100° C (-22° to +212° F)
Banner offers a wide selection of high-quality retroreflective targets. See the Accessories
section of your current Banner Photoelectric Sensors catalog for complete information.
NOTE: Polarized sensors require corner cube type retroreflective targets. Non-polarized
sensors may use any retroreflective target.
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
VALU-BEAM® Sensors – 912 Series
P/N 03467 rev. E
WARRANTY: Banner Engineering Corp. warrants its
products to be free from defects for one year. Banner
Engineering Corp. will repair or replace, free of charge, any
product of its manufacture found to be defective at the time
it is returned to the factory during the warranty period. This
warranty does not cover damage or liability for the improper
application of Banner products. This warranty is in lieu of
any other warranty either expressed or implied.
Mounting Brackets
SMB30C • 30 mm split clamp, black PBT bracket
• Stainless steel mounting hardware included SMB30SC • 30 mm swivel, black PBT bracket
• Stainless steel mounting hardware included
SMB30MM
• 30 mm, 12-gauge stainless steel bracket
with curved mounting slots for versatile
orientation
• Clearance for M6 (1/4") hardware
50.8 mm
(2.00")
58.7 mm
(2.31")
66.5 mm
(2.62")
30.0 mm
(1.18")
29.0 mm
(1.14")
12.7 mm
(0.50")
M30 x 1.5
internal
thread
56.0 mm
(2.20")
63.0 mm
(2.48")
45.0 mm
(1.77")
2.5 mm
(0.10")
31.5 mm
(1.24")
Nut Plate
M5 x 0.8
x 80 mm
Screw (2)
13 mm
(0.5")
13.5 mm (0.53")
SMB30C BRACKET
35.1 mm
(1.38")
35.1 mm
(1.38")
69.9 mm
(2.75")
7.1 mm
.28 x 90° (2 Slots)
R 25.4 mm
(1.00")
ø30.1 mm
(1.19")
57.2 mm
(2.25")
25.4 mm
(1.00")
25.4 mm
(1.00")
ø 6.4 mm
(0.25" dia.)
57.2 mm
(2.25")
Replacement Lens Assemblies
VALU-BEAM lens assemblies are field-replaceable. In addition, some lenses may be used to convert from one sensing mode to another, or
to change the sensing range of a particular sensor. The possible conversions are listed in the table below.
Models Description Possible Sensing Mode or Range Changes
UC-900AG
UC-900C
UC-900DSR
UC-900F
UC-900FP
UC-900L
UC-900J
Replacement lens for LVAG
Replacement lens for C and CV
Replacement lens for DSR, ESR, and RSR
Replacement lens for F
Replacement lens for FP
Replacement lens for E, R, LV, and D
Attach to E, R, ESR, RSR, LV, and D models
Change LV to LVAG
Change LV to CV
Change D or F to DSR, EF to ESR, and RF to RSR
Change D to F and DSR to F
–
Change LVAG to LV, CV to LV, DSR to D, and F to D
Flat polycarbonate dust cover
