AD7893AR-3REEL - Analog Devices, Inc.

FUNCTIONAL BLOCK DIAGRAM

AGND

DGND SCLK

CONVST

AD7893

SDATA

REF IN

TRACK/

HOLD

*AD7893-5, AD7893-10, AD7893-3

SIGNAL

SCALING* 12-BIT

ADC

OUTPUT

REV. E

Information furnished by Analog Devices is believed to be accurate and

reliable. However, no responsibility is assumed by Analog Devices for its

use, nor for any infringements of patents or other rights of third parties

which may result from its use. No license is granted by implication or

otherwise under any patent or patent rights of Analog Devices.

MOS 12-Bit, Serial 6 ms

ADC in 8-Pin Package

AD7893

FEATURES

Fast 12-Bit ADC with 6 ms Conversion Time

8-Pin Mini-DlP and SOIC

Single Supply Operation

High Speed, Easy-to-Use, Serial Interface

On-Chip Track/Hold Amplifier

Selection of Input Ranges

610 V for AD7893-10

62.5 V for AD7893-3

0 V to +2.5 V for AD7893-2

0 V to +5 V for AD7893-5

Low Power: 25 mW typ

GENERAL DESCRIPTION

The AD7893 is a fast, 12-bit ADC that operates from a single

+5 V supply and is housed in a small 8-pin mini-DIP and 8-pin

SOIC. The part contains a 6 µs successive approximation A/D

converter, an on-chip track/hold amplifier, an on-chip clock and

a high speed serial interface.

Output data from the AD7893 is provided via a high speed,

serial interface port. This two-wire serial interface has a serial

clock input and a serial data output with the external serial clock

accessing the serial data from the part.

In addition to traditional dc accuracy specifications such as lin-

earity, full-scale and offset errors, the AD7893 is also specified

for dynamic performance parameters, including harmonic dis-

tortion and signal-to-noise ratio.

The part accepts an analog input range of ±10 V (AD7893-10),

±2.5 V (AD7893-3), 0 V to +5 V (AD7893-5) or 0 V to +2.5 V

(AD7893-2) and operates from a single +5 V supply, consuming

only 25 mW typical.

The AD7893 is fabricated in Analog Devices’ Linear Compat-

ible CMOS (LC

MOS) process, a mixed technology process

that combines precision bipolar circuits with low power CMOS

logic. The part is available in a small, 8-pin, 0.3" wide, plastic or

hermetic dual-in-line package (mini-DIP) and in an 8-pin, small

outline IC (SOIC).

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 617/329-4700 World Wide Web Site: http://www.analog.com

Fax: 617/326-8703 © Analog Devices, Inc., 1997

PRODUCT HIGHLIGHTS

1. Fast, 12-Bit ADC in 8-Pin Package

The AD7893 contains a 6 µs ADC, a track/hold amplifier,

control logic and a high speed serial interface, all in an 8-pin

package. This offers considerable space saving over alterna-

tive solutions.

2. Low Power, Single Supply Operation

The AD7893 operates from a single +5 V supply and con-

sumes only 25 mW. This low power, single supply operation

makes it ideal for battery powered or portable applications.

3. High Speed Serial Interface

The part provides high speed serial data and serial clock lines,

allowing for an easy, two-wire serial interface arrangement.

AD7893–SPECIFICATIONS

ABS

Parameter Versions

Versions Version Units Test Conditions/Comments

DYNAMIC PERFORMANCE

Signal to (Noise + Distortion) Ratio

@ +25°C 70 70 70 dB min f

= 10 kHz Sine Wave, f

SAMPLE

= 117 kHz

Total Harmonic Distortion (THD)

–80 –80 –80 dB max f

= 10 kHz Sine Wave, f

SAMPLE

= 117 kHz

Peak Harmonic or Spurious Noise

–80 –80 –80 dB max f

= 10 kHz Sine Wave, f

SAMPLE

= 117 kHz

Intermodulation Distortion (IMD)

fa = 9 kHz, fb = 9.5 kHz, f

SAMPLE

= 117 kHz

2nd Order Terms –80 –80 –80 dB max

3rd Order Terms –80 –80 –80 dB max

DC ACCURACY

Resolution 12 12 12 Bits

Minimum Resolution for which

No Missing Codes are Guaranteed 12 12 12 Bits

Relative Accuracy

±1±1/2 ±1 LSB max

Differential Nonlinearity

±1±1±1 LSB max

Positive Full-Scale Error

±3±1.5 ±3 LSB max

AD7893-2, AD7893-5

Unipolar Offset Error ±4±3±4 LSB max

AD7893-10, AD7893-3

Negative Full-Scale Error

±3±1.5 ±3 LSB max

Bipolar Zero Error ±4±2±4 LSB max

ANALOG INPUT

AD7893-10

Input Voltage Range ±10 ±10 ±10 Volts

Input Resistance 16 16 16 kΩ min

AD7893-3

Input Voltage Range ±2.5 ±2.5 ±2.5 Volts

Input Resistance 4 4 4 kΩ min

AD7893-5

Input Voltage Range 0 to +5 0 to +5 0 to +5 Volts

Input Resistance 9 9 9 kΩ min

AD7893-2

Input Voltage Range 0 to +2.5 0 to +2.5 0 to +2.5 Volts

Input Current 500 500 500 nA max

REFERENCE INPUT

REF IN Input Voltage Range 2.375/2.625 2.375/2.625 2.375/2.625 V min/V max 2.5 V ± 5%

Input Current 2 2 10 µA max

Input Capacitance

10 10 10 pF max

LOGIC INPUTS

Input High Voltage, V

INH

2.4 2.4 2.4 V min V

= 5 V ± 5%

Input Low Voltage, V

INL

0.8 0.8 0.8 V max V

= 5 V ± 5%

Input Current, I

±10 ±10 ±10 µA max V

= 0 V to V

Input Capacitance, C

IN3

10 10 10 pF max

LOGIC OUTPUTS

Output High Voltage, V

4.0 4.0 4.0 V min I

SOURCE

= 200 µA

Output Low Voltage, V

0.4 0.4 0.4 V max I

SINK

= 1.6 mA

Output Coding

AD7893-10, AD7893-3 2s Complement

AD7893-2, AD7893-5 Straight (Natural) Binary

CONVERSION RATE

Conversion Time 6 6 6 µs max

Track/Hold Acquisition Time

1.5 1.5 1.5 µs max

POWER REQUIREMENTS

+5 +5 +5 V nom ±5% for Specified Performance

9 9 9 mA max

Power Dissipation 45 45 45 mW max Typically 25 mW

NOTES

Temperature Ranges are as follows: A, B Versions: –40°C to +85°C, S Version: –55°C to +125°C.

See Terminology.

Sample tested @ +25°C to ensure compliance.

Specifications subject to change without notice.

REV. E

–2–

= +5 V, AGND = DGND = 0 V, REF IN = +2.5 V. All specifications T

MIN

to T

MAX

unless

otherwise noted.)

AD7893

–3–

REV. E

TIMING CHARACTERISTICS

1, 2

A, B S

Parameter Versions Version Units Test Conditions/Comments

50 50 ns min CONVST Pulse Width

60 70 ns min SCLK High Pulse Width

30 40 ns min SCLK Low Pulse Width

50 60 ns max SCLK Rising Edge to Data Valid Delay

10 10 ns min Bus Relinquish Time after Falling Edge of SCLK

100 100 ns max

NOTES

Sample tested at +25°C to ensure compliance. All input signals are measured with tr = tf = 1 ns (10% to 90% of +5 V) and timed from a voltage level of +1.6 V.

See Figure 5.

Measured with the load circuit of Figure 1 and defined as the time required for an output to cross 0.8 V or 2.4 V.

Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back

to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t

, quoted in the timing characteristics is the true bus relinquish time

of the part and, as such, is independent of external bus loading capacitances.

(VDD = +5 V, AGND = DGND = 0 V, REF IN = +2.5 V)

ABSOLUTE MAXIMUM RATINGS*

= +25°C unless otherwise noted)

to AGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

to DGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

Analog Input Voltage to AGND

AD7893-10, AD7893-5 . . . . . . . . . . . . . . . . . . . . . . . ±17 V

AD7893-2, AD7893-3 . . . . . . . . . . . . . . . . . . . –5 V, +10 V

Reference Input Voltage to AGND . . . –0.3 V to V

+ 0.3 V

Digital Input Voltage to DGND . . . . . –0.3 V to V

+ 0.3 V

Digital Output Voltage to DGND . . . . –0.3 V to V

+ 0.3 V

Operating Temperature Range

Commercial (A, B Versions) . . . . . . . . . . . –40°C to +85°C

Extended (S Version) . . . . . . . . . . . . . . . . –55°C to +125°C

Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C

Plastic DIP Package, Power Dissipation . . . . . . . . . . 450 mW

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 130°C/W

Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . +260°C

Cerdip Package, Power Dissipation . . . . . . . . . . . . . . 450 mW

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 125°C/W

Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . +300°C

SOIC Package, Power Dissipation . . . . . . . . . . . . . . . 450 mW

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 170°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C

*Stresses above those listed under “Absolute Maximum Ratings” may cause

permanent damage to the device. This is a stress rating only; functional operation

of the device at these or any other conditions above those listed in the operational

sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

OUTPUT

PIN +2.1V

1.6mA

200µA

50pF

Figure 1. Load Circuit for Access Time and Bus

Relinquish Time

WARNING!

ESD SENSITIVE DEVICE

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection. Although

the AD7893 features proprietary ESD protection circuitry, permanent damage may occur on devices

subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are

recommended to avoid performance degradation or loss of functionality.

AD7893

REV. E

–4–

PIN FUNCTION DESCRIPTION

Pin Pin

No. Mnemonic Description

1 REF IN Voltage Reference Input. An external reference source should be connected to this pin to provide the refer-

ence voltage for the AD7893’s conversion process. The REF IN input is buffered on-chip. The nominal ref-

erence voltage for correct operation of the AD7893 is +2.5 V.

Analog Input Channel. The analog input range is ±10 V (AD7893-10), ±2.5 V (AD7893-3), 0 V to +5 V

(AD7893-5) and 0 V to +2.5 V (AD7893-2).

3 AGND Analog Ground. Ground reference for track/hold, comparator and DAC.

4 SCLK Serial Clock Input. An external serial clock is applied to this input to obtain serial data from the AD7893. A

new serial data bit is clocked out on the rising edge of this serial clock, and data is valid on the falling edge.

The serial clock input should be taken low at the end of the serial data transmission.

5 SDATA Serial Data Output. Serial data from the AD7893 is provided at this output. The serial data is clocked out by

the rising edge of SCLK and is valid on the falling edge of SCLK. Sixteen bits of serial data are provided

with four leading zeros followed by the 12 bits of conversion data. On the sixteenth falling edge of SCLK, the

SDATA line is disabled (three-stated). Output data coding is twos complement for the AD7893-10 and

AD7893-3, straight binary for the AD7893-2 and AD7893-5.

6 DGND Digital Ground. Ground reference for digital circuitry.

7CONVST Convert Start. Edge-triggered logic input. On the falling edge of this input, the serial clock counter is reset to

zero. On the rising edge of this input, the track/hold goes into its hold mode and conversion is initiated.

Positive supply voltage, +5 V ± 5%.

PIN CONFIGURATION

DIP and SOIC

REF IN

VIN

AGND

SCLK

DGND

SDATA

VDD

CONVST

AD7893

TOP VIEW

(NOT TO SCALE)

ORDERING GUIDE

Temperature Linearity Package

Model Range Error SNR Options*

AD7893AN-2 –40°C to +85°C±1 LSB 70 dB N-8

AD7893BN-2 –40°C to +85°C±1/2 LSB 72 dB N-8

AD7893AR-2 –40°C to +85°C±1 LSB 70 dB SO-8

AD7893BR-2 –40°C to +85°C±1/2 LSB 72 dB SO-8

AD7893SQ-2 –55°C to +125°C±1 LSB 70 dB Q-8

AD7893AN-5 –40°C to +85°C±1 LSB 70 dB N-8

AD7893BN-5 –40°C to +85°C±1/2 LSB 72 dB N-8

AD7893AR-5 –40°C to +85°C±1 LSB 70 dB SO-8

AD7893BR-5 –40°C to +85°C±1/2 LSB 72 dB SO-8

AD7893SQ-5 –55°C to +125°C±1 LSB 70 dB Q-8

AD7893AN-10 –40°C to +85°C±1 LSB 70 dB N-8

AD7893BN-10 –40°C to +85°C±1/2 LSB 72 dB N-8

AD7893AR-10 –40°C to +85°C±1 LSB 70 dB SO-8

AD7893BR-10 –40°C to +85°C±1/2 LSB 72 dB SO-8

AD7893SQ-10 –55°C to +125°C±1 LSB 70 dB Q-8

AD7893AR-3 –40°C to +85°C±1 LSB 70 dB SO-8

*N = Plastic DIP, Q = Cerdip, SO = SOIC.

AD7893

–5–

REV. E

Relative Accuracy

Relative accuracy or endpoint nonlinearity is the maximum

deviation from a straight line passing through the endpoints of

the ADC transfer function.

Differential Nonlinearity

This is the difference between the measured and the ideal 1 LSB

change between any two adjacent codes in the ADC.

Positive Full-Scale Error (AD7893-10)

This is the deviation of the last code transition (01 . . . 110 to

01 . . . 111) from the ideal 4 × REF IN – 1 LSB (AD7893-10

±10 V range) after the Bipolar Zero Error has been adjusted out.

Positive Full-Scale Error (AD7893-3)

This is the deviation of the last code transition (01 . . . 110 to

01 . . . 111) from the ideal (REF IN – 1 LSB) after the

Bipolar Zero Error has been adjusted out.

Positive Full-Scale Error (AD7893-5)

This is the deviation of the last code transition (11 . . . 110 to

11 . . . 111) from the ideal (2 × REF IN – 1 LSB) after the Uni-

polar Offset Error has been adjusted out.

Positive Full-Scale Error (AD7893-2)

This is the deviation of the last code transition (11 . . . 110 to

11 . . . 111) from the ideal (REF IN – 1 LSB) after the Unipolar

Offset Error has been adjusted out.

Bipolar Zero Error (AD7893-10, 610 V; AD7893-3, 62.5 V)

This is the deviation of the midscale transition (all 0s to all 1s)

from the ideal 0 V (AGND).

Unipolar Offset Error (AD7893-2, AD7893-5)

This is the deviation of the first code transition (00 . . . 000 to

00 . . . 001) from the ideal 1 LSB.

Negative Full-Scale Error (AD7893-10)

This is the deviation of the first code transition (10 . . . 000 to

10 . . . 001) from the ideal –4 × REF IN + 1 LSB (AD7893-10

±10 V range) after Bipolar Zero Error has been adjusted out.

Negative Full-Scale Error (AD7893-3)

This is the deviation of the first code transition (10 . . . 000 to

10 . . . 001) from the ideal (–REF IN + 1 LSB) after Bipolar

Zero Error has been adjusted out.

Track/Hold Acquisition Time

Track/Hold acquisition time is the time required for the output

of the track/hold amplifier to reach its final value, within

±1/2 LSB, after the end of conversion (the point at which the

track/hold returns to track mode). It also applies to situations

where there is a step input change on the input voltage applied

to the V

input of the AD7893. This means that the user must

wait for the duration of the track/hold acquisition time after the

end of conversion or after a step input change to V

before

starting another conversion, to ensure that the part operates to

specification.

TERMINOLOGY

Signal to (Noise + Distortion) Ratio

This is the measured ratio of signal to (noise + distortion) at the

output of the A/D converter. The signal is the rms amplitude of

the fundamental. Noise is the rms sum of all nonfundamental

signals up to half the sampling frequency (f

/2), excluding dc.

The ratio is dependent upon the number of quantization levels

in the digitization process; the more levels, the smaller the quan-

tization noise. The theoretical signal to (noise + distortion) ratio

for an ideal N-bit converter with a sine wave input is given by:

Signal to (Noise + Distortion) = (6.02 N + 1.76) dB

Thus for a 12-bit converter, this is 74 dB.

Total Harmonic Distortion

Total harmonic distortion (THD) is the ratio of the rms sum of

harmonics to the fundamental. For the AD7893, it is defined as:

where V

is the rms amplitude of the fundamental and V

, V

and V

are the rms amplitudes of the second through the

sixth harmonics.

Peak Harmonic or Spurious Noise

Peak harmonic or spurious noise is defined as the ratio of the

rms value of the next largest component in the ADC output

spectrum (up to f

/2 and excluding dc) to the rms value of the

fundamental. Normally, the value of this specification is deter-

mined by the largest harmonic in the spectrum, but for parts

where the harmonics are buried in the noise floor, it will be a

noise peak.

Intermodulation Distortion

With inputs consisting of sine waves at two frequencies, fa and

fb, any active device with nonlinearities will create distortion

products at sum and difference frequencies of mfa ± nfb where

m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for

which neither m nor n are equal to zero. For example, the second

order terms include (fa + fb) and (fa – fb), while the third order

terms include (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (fa – 2 fb).

The AD7893 is tested using the CCIF standard where two

input frequencies near the top end of the input bandwidth are

used. In this case, the second and third order terms are of differ-

ent significance. The second order terms are usually distanced

in frequency from the original sine waves, while the third order

terms are usually at a frequency close to the input frequencies.

As a result, the second and third order terms are specified sepa-

rately. The calculation of the intermodulation distortion is per

the THD specification where it is the ratio of the rms sum of the

individual distortion products to the rms amplitude of the fun-

damental expressed in dBs.

THD(dB)=20 log V

AD7893

REV. E

–6–

CONVERTER DETAILS

The AD7893 is a fast, 12-bit single supply A/D converter. It

provides the user with signal scaling (AD7893-10), track/hold,

A/D converter and serial interface logic functions on a single

chip. The A/D converter section of the AD7893 consists of a

conventional successive-approximation converter based on an

R-2R ladder structure. The signal scaling on the AD7893-10,

AD7893-5 and AD7893-3 allows the part to handle ±10 V, 0 V

to +5 V and ±2.5 V input signals, respectively, while operating

from a single +5 V supply. The AD7893-2 accepts an analog in-

put range of 0 V to +2.5 V. The part requires an external +2.5 V

reference. The reference input to the part is buffered on-chip.

A major advantage of the AD7893 is that it provides all of the

above functions in an 8-pin package, either 8-pin mini-DIP or

SOIC. This offers the user considerable space saving advantages

over alternative solutions. The AD7893 typically consumes only

25 mW, making it ideal for battery-powered applications.

Conversion is initiated on the AD7893 by pulsing the CONVST

input. On the rising edge of CONVST, the on-chip track/hold

goes from track-to-hold mode and the conversion sequence is

started. The conversion clock for the part is generated internally

using a laser-trimmed clock oscillator circuit. Conversion time

for the AD7893 is 6 µs, and the track/hold acquisition time is

1.5 µs. To obtain optimum performance from the part, the read

operation should not occur during the conversion or during

600 ns prior to the next conversion. This allows the part to op-

erate at throughput rates up to 117 kHz and to achieve data

sheet specifications. The part can operate at higher throughput

rates (up to 133 kHz) with slightly degraded performance (see

Timing and Control section).

CIRCUIT DESCRIPTION

Analog Input Section

The AD7893 is offered as four part types: the AD7893-10,

which handles a ±10 V input voltage range; the AD7893-3,

which handles a ±2.5 V input voltage range; the AD7893-5,

which handles a 0 V to +5 V input range; and the AD7893-2,

which handles a 0 V to +2.5 V input voltage range.

Figure 2 shows the analog input section for the AD7893-10,

AD7893-5 and AD7893-3. The analog input range of the

AD7893-10 is ±10 V into an input resistance of typically 33 kΩ.

The analog input range of the AD7893-3 is ±2.5 V into an input

resistance of typically 12 kΩ. The input range on the AD7893-5 is

0 V to +5 V into an input resistance of typically 11 kΩ. This in-

put is benign with no dynamic charging currents, as the resistor

stage is followed by a high input impedance stage of the track/hold

AGND

AD7893-10/AD7893-5

REF IN

TRACK/

HOLD

TO ADC

REFERENCE

CIRCUITRY

TO INTERNAL

COMPARATOR

Figure 2. AD7893-10/AD7893-3/AD7893-5 Analog Input

Structure

amplifier. For the AD7893-10, R1 = 30 kΩ; R2 = 7.5 kΩ and

R3 = 10 kΩ. For the AD7893-3, R1 = R2 = 6.5 kΩ, and R3

is open circuit. For the AD7893-5, R1 and R3 = 5 kΩ while

R2 is open-circuit.

For the AD7893-10 and AD7893-3, the designed code transi-

tions occur on successive integer LSB values (i.e., 1 LSB, 2 LSBs,

3 LSBs . . .). Output coding is twos complement binary with

1 LSB = FS/4096. The ideal input/output transfer function for

the AD7893-10 and AD7893-3 is shown in Table I.

Table I. Ideal Input/Output Code Table for the AD7893-10/

AD7893-3

Digital Output

Analog Input

Code Transition

+FSR/2 – 1 LSB

011 . . . 110 to 011 . . . 111

+FSR/2 – 2 LSBs 011 . . . 101 to 011 . . . 110

+FSR/2 – 3 LSBs 011 . . . 100 to 011 . . . 101

AGND + 1 LSB 000 . . . 000 to 000 . . . 001

AGND 111 . . . 111 to 000 . . . 000

AGND – 1 LSB 111 . . . 110 to 111 . . . 111

–FSR/2 + 3 LSBs 100 . . . 010 to 100 . . . 011

–FSR/2 + 2 LSBs 100 . . . 001 to 100 . . . 010

–FSR/2 + 1 LSB 100 . . . 000 to 100 . . . 001

NOTES

FSR is full-scale range and is 20 V (AD7893-10) and = 5 V (AD7893-3) with

REF IN = +2.5 V.

1 LSB = FSR/4096 = 4.883 mV (AD7893-10) and 1.22 mV (AD7893-3) with

REF IN = +2.5 V.

For the AD7893-5, the designed code transitions occur again on

successive integer LSB values. Output coding is straight (natural)

binary with 1 LSB = FS/4096 = 5 V/4096 = 1.22 mV. The ideal

input/output transfer function for the AD7893-5 is shown in

Table II.

The analog input section for the AD7893-2 contains no biasing

resistors, and the V

pin drives the input directly to the track/

hold amplifier. The analog input range is 0 V to +2.5 V into a

high impedance stage, with an input current of less than

500 nA. This input is benign, with no dynamic charging cur-

rents. Once again, the designed code transitions occur on suc-

cessive integer LSB values. Output coding is straight (natural)

binary with 1 LSB = FS/4096 = 2.5 V/4096 = 0.61 mV. Table

II also shows the ideal input/output transfer function for the

AD7893-2.

Table II. Ideal Input/Output Code Table for

AD7893-2/AD7893-5

Digital Output

Analog Input

Code Transition

+FSR – 1 LSB

111 . . . 110 to 111 . . . 111

+FSR – 2 LSB 111 . . . 101 to 111 . . . 110

+FSR – 3 LSB 111 . . . 100 to 111 . . . 101

AGND + 3 LSB 000 . . . 010 to 000 . . . 011

AGND + 2 LSB 000 . . . 001 to 000 . . . 010

AGND + 1 LSB 000 . . . 000 to 000 . . . 001

NOTES

FSR is Full-Scale Range and is 5 V for AD7893-5 and 2.5 V for AD7893-2

with REF IN = +2.5 V.

1 LSB = FSR/4096 and is 1.22 mV for AD7893-5 and 0.61 mV for AD7893-2

with REF IN = +2.5 V.

AD7893

–7–

REV. E

Track/Hold Section

The track/hold amplifier on the analog input of the AD7893

allows the ADC to accurately convert an input sine wave of full-

scale amplitude to 12-bit accuracy. The input bandwidth of the

track/hold is greater than the Nyquist rate of the ADC, even

when the ADC is operated at its maximum throughput rate of

117 kHz (i.e., the track/hold can handle input frequencies in

excess of 58 kHz).

The track/hold amplifier acquires an input signal to 12-bit accu-

racy in less than 1.5 µs. The operation of the track/hold is essen-

tially transparent to the user. The track/hold amplifier goes from

its tracking mode to its hold mode at the start of conversion

(i.e., the rising edge of CONVST). The aperture time for the

track/hold (i.e., the delay time between the external CONVST

signal and the track/hold actually going into hold) is typically

15 ns. At the end of conversion (6 µs after the rising edge of

CONVST) the part returns to its tracking mode. The acquisi-

tion time of the track/hold amplifier begins at this point.

Reference Input

The reference input to the AD7893 is a buffered on-chip with a

maximum reference input current of 1 µA. The part is specified

with a +2.5 V reference input voltage. Errors in the reference

source will result in gain errors in the AD7893’s transfer func-

tion and will add to the specified full-scale errors on the part.

On the AD7893-10 it will also result in an offset error injected

in the attenuator stage. Suitable reference sources for the

AD7893 include the AD780 and AD680 precision +2.5 V

references.

Timing and Control Section

Figure 3 shows the timing and control sequence required to ob-

tain optimum performance from the AD7893. In the sequence

shown, conversion is initiated on the rising edge of CONVST,

and new data from this conversion is available in the output reg-

ister of the AD7893 6 µs later. Once the read operation has

taken place, a further 600 ns should be allowed before the next

rising edge of CONVST to optimize the settling of the track/

hold amplifier before the next conversion is initiated. With the

serial clock frequency at its maximum of 8.33 MHz, the achiev-

able throughput rate for the part is 6 µs (conversion time) plus

1.92 µs (read time) plus 0.6 µs (acquisition time). This results in

a minimum throughput time of 8.52 µs (equivalent to a through-

put rate of 117 kHz).

The read operation consists of sixteen serial clock pulses to the

output shift register of the AD7893. After sixteen serial clock

pulses the shift register is reset and the SDATA line is three-

stated. If there are more serial clock pulses after the sixteenth

clock, the shift register will be moved on past its reset state;

however, the shift register will be reset again on the falling edge

of the CONVST signal to ensure that the part returns to a

known state every conversion cycle. As a result, a read operation

from the output register should not straddle across the falling

edge of CONVST as the output shift register will be reset in the

middle of the read operation, and the data read back into the

microprocessor will appear invalid.

The throughput rate of the part can be increased by reading

data during conversion. If the data is read during conversion,

a throughput time of 6 µs (conversion time) plus 1.5 µs is

achieved. This minimum throughput time of 7.5 µs is achieved

with a slight reduction in performance from the AD7893. The

signal to (noise + distortion) number is likely to degrade by ap-

proximately 1.5 dB while the code flicker from the part will also

increase (see AD7893 PERFORMANCE section).

Because the AD7893 is provided in an 8-pin package to mini-

mize board space, the number of pins available for interfacing is

very limited. As a result, no status signal is provided from the

AD7893 to indicate when conversion is complete. In many

applications, this will not be a problem as the data can be read

from the AD7893 during conversion or after conversion; how-

ever, applications that want to achieve optimum performance

from the AD7893 will have to ensure that the data read does not

occur during conversion or during 600 ns prior to the rising

edge of CONVST. This can be achieved in two ways. The first

is to ensure in software that the read operation is not initiated

until 6 µs after the rising edge of CONVST. This will only be

possible if the software knows when the CONVST command is

issued. The second scheme would be to use the CONVST sig-

nal as both the conversion start signal and an interrupt signal.

The simplest way to do this would be to generate a square wave

signal for CONVST with high and low times of 6 µs (see Figure

4). Conversion is initiated on the rising edge of CONVST. The

falling edge of CONVST occurs 6 µs later and can be used as ei-

ther an active low or falling, edge-triggered interrupt signal to

tell the processor to read the data from the AD7893. Provided

that the read operation is completed 600 ns before the rising

edge of CONVST, the AD7893 will operate to specification.

CONVST

SCLK

CONVERSION IS INITIATED

AND TRACK/HOLD GOES

INTO HOLD

CONVERSION ENDS

6µs LATER SERIAL READ

OPERATION OUTPUT SERIAL

SHIFT REGISTER IS

RESET

600ns MIN

tCONVERT

READ OPERATION

SHOULD END 600ns

PRIOR TO NEXT

RISING EDGE OF

CONVST

Figure 3. Timing Sequence for Optimum Performance from the AD7893

AD7893

REV. E

–8–

This scheme limits the throughput rate to 12 µs minimum; how-

ever, depending on the response time of the microprocessor to

the interrupt signal and the time taken by the processor to read

the data, this may be the fastest the system could have operated.

In any case, the CONVST signal does not have to have a 50:50

duty cycle. This can be tailored to optimize the throughput rate

of the part for a given system.

Alternatively, the CONVST signal can be used as a normal narrow

pulse width. The rising edge of CONVST can be used as an active

high or rising edge-triggered interrupt. A software delay of 6 µs can

then be implemented before data is read from the part.

Serial Interface

The serial interface to the AD7893 consists of just two wires, a

serial clock input (SCLK) and the serial data output (SDATA).

This allows for an easy to use interface to most microcontrollers,

DSP processors and shift registers.

Figure 5 shows the timing diagram for the read operation to the

AD7893. The serial clock input (SCLK) provides the clock

source for the serial interface. Serial data is clocked out from the

SDATA line on the rising edge of this clock and is valid on the

falling edge of SCLK. Sixteen clock pulses must be provided to

the part to access to full conversion result. The AD7893 pro-

vides four leading zeros followed by the 12-bit conversion result

starting with the MSB (DB11). The last data bit to be clocked

out on the final rising clock edge is the LSB (DB0). On the six-

teenth falling edge of SCLK, the SDATA line is disabled (three-

stated). After this last bit has been clocked out, the SCLK input

should return low and remain low until the next serial data read

operation. If there are extra clock pulses after the sixteenth

clock, the AD7893 will start over again with outputting data

from its output register, and the data bus will no longer be

three-stated even when the clock stops. Provided that the serial

clock has stopped before the next falling edge of CONVST, the

AD7893 will continue to operate correctly with the output shift

the SCLK line must be low when CONVST goes low in order

to reset the output shift register correctly.

The serial clock input does not have to be continuous during the

serial read operation. The sixteen bits of data (four leading zeros

and 12 bit conversion result) can be read from the AD7893 in a

number of bytes; however, the SCLR input must remain low be-

tween the two bytes.

Normally, the output register is updated at the end of conver-

sion. If a serial read from the output register is in progress when

conversion is complete; however, the updating of the output

when the serial read is completed. If the serial read has not been

completed before the next falling edge of CONVST, the output

the output shift register count is reset. In applications where the

data read has been started and not completed before the falling

edge of CONVST, the user must provide a CONVST pulse

width of greater than 1.5 µs to ensure correct setup of the AD7893

before the next conversion is initiated. In applications where the

output update takes place either at the end of conversion or at

the end of a serial read that is completed 1.5 µs before the rising

edge of CONVST, the normal pulse width of 50 ns minimum

applies to CONVST.

CONVST

SCLK

CONVERSION IS INITIATED

AND TRACK/HOLD GOES

INTO HOLD

CONVST INDICATES

TO µP THAT

CONVERSION IS

COMPLETE

CONVERT

SERIAL READ

OPERATION

µP INT SERVICE

OR POLLING

ROUTINE

600ns MIN

READ OPERATION

SHOULD END 600ns

PRIOR TO NEXT

RISING EDGE OF

CONVST

Figure 4.

CONVST

Used as Status Signal

SDATA (O)

SCLK (I)

FOUR LEADING ZEROS DB11 DB10

THREE-STATE THREE-STATE

DB0

Figure 5. Data Read Operation

AD7893

–9–

REV. E

The AD7893 counts the serial clock edges to know which bit

from the output register should be placed on the SDATA out-

put. To ensure that the part does not lose synchronization, the

serial clock counter is reset on the falling edge of the CONVST

input, provided the SCLR line is low. The user should ensure

that a falling edge on the CONVST input does not occur while

a serial data read operation is in progress.

MICROPROCESSOR/MICROCONTROLLER INTERFACE

The AD7893 provides a two-wire serial interface that can be

used for connection to the serial ports of DSP processors and

microcontrollers. Figures 6 through 9 show the AD7893 inter-

faced to a number of different microcontrollers and DSP pro-

cessors. The AD7893 accepts an external serial clock and, as a

result, in all interfaces shown here, the processor/controller is

configured as the master, providing the serial clock with the

AD7893 configured as the slave in the system.

AD7893-8051 Interface

Figure 6 shows an interface between the AD7893 and the

8XC51 microcontroller. The 8XC51 is configured for its Mode

0 serial interface mode. The diagram shows the simplest form of

the interface where the AD7893 is the only part connected to

the serial port of the 8XC51 and, therefore, no decoding of the

serial read operations is required. It also makes no provisions for

monitoring when conversion is complete on the AD7893.

Either of these two tasks can readily be accomplished with minor

modifications to the interface. To chip select the AD7893 in

systems where more than one device is connected to the 8XC51’s

serial port, a port bit configured as an output from one of the

8XC51’s parallel ports can be used to gate on or off the serial

clock to the AD7893. A simple AND function on this port bit

and the serial clock from the 8XC51 will provide this function.

The port bit should be high to select the AD7893 and low when

it is not selected.

To monitor the conversion time on the AD7893, a scheme such

as previously outlined with CONVST can be used. This can be

implemented in two ways. One is to connect the CONVST line

to another parallel port bit that is configured as an input. This

port bit can then be polled to determine when conversion is

complete. An alternative is to use an interrupt driven system, in

which case the CONVST line should be connected to the INT1

input of the 8XC51.

The serial clock rate from the 8XC51 is limited to significantly

less than the allowable input serial clock frequency with which

the AD7893 can operate. As a result, the time to read data from

the part will actually be longer than the conversion time of the

part. This means that the AD7893 cannot run at its maximum

throughput rate when used with the 8XC51.

AD7893-68HC11 Interface

An interface circuit between the AD7893 and the 68HC11

microcontroller is shown in Figure 7. For the interface shown,

the 68HC11 SPI port is used, and the 68HC11 is configured in

its single-chip mode. The 68HC11 is configured in the master

mode with its CPOL bit set to a logic zero and its CPHA bit set

to a logic one. As with the previous interface, the diagram shows

the simplest form of the interface where the AD7893 is the only

part connected to the serial port of the 68HC11 and, therefore,

no decoding of the serial read operations is required. It also

makes no provisions for monitoring when conversion is com-

plete on the AD7893.

Once again, either of these two tasks can readily be accom-

plished with minor modifications to the interface. To chip select

the AD7893 in systems where more than one device is con-

nected to the 68HC11’s serial port, a port bit, configured as an

output from one of the 68HC11’s parallel ports, can be used to

gate on or off the serial clock to the AD7893. A simple AND

function on this port bit and the serial clock from the 68HC11

will provide this function. The port bit should be high to select

the AD7893 and low when it is not selected.

To monitor the conversion time on the AD7893, a scheme such

as outlined in the previous interface with CONVST can be

used. This can be implemented in two ways. One is to connect

the CONVST line to another parallel port bit that is configured

as an input. This port bit can then be polled to determine when

conversion is complete. An alternative is to use an interrupt

driven system, in which case the CONVST line should be con-

nected to the IRQ input of the 68HC11.

The serial clock rate from the 68HC11 is limited to significantly

less than the allowable input serial clock frequency with which

the AD7893 can operate. As a result, the time to read data from

the part will actually be longer than the conversion time of the

part. This means that the AD7893 cannot run at its maximum

throughput rate when used with the 68HC11.

AD7893

SDATA

SCLK

8XC51

P3.0

P3.1

Figure 6. AD7893 to 8XC51 Interface

AD7893

SDATA

SCLK

68HC11

SCK

MISO

Figure 7. AD7893 to 68HC11 Interface

AD7893

REV. E

–10–

AD7893–ADSP-2105 Interface

An interface circuit between the AD7893 and the ADSP-2105

DSP processor is shown in Figure 8. In the interface shown, the

RFS1 output from the ADSP-2105’s SPORT1 serial port is

used to gate the serial clock (SCLK1) of the ADSP-2105 before

it is applied to the SCLK input of the AD7893. The RFS1 out-

put is configured for active high operation. The interface

ensures a noncontinuous clock for the AD7893’s serial clock

input with only sixteen serial clock pulses provided, and the

serial clock line of the AD7893 remaining low between data

transfers. The SDATA line from the AD7893 is connected to

the DR1 line of the ADSP-2105’s serial port.

AD7893

SDATA

SCLK

ADSP-2105

DR1

RFS1

SCLK1

Figure 8. AD7893 to ADSP-2105 Interface

The timing relationship between the SCLK1 and RFS1 outputs

of the ADSP-2105 are such that the delay between the rising

edge of the SCLK1 and the rising edge of an active high RFS1

is up to 25 ns. There is also a requirement that data must be set

up 10 ns prior to the falling edge of the SCLK1 to be read cor-

rectly by the ADSP-2105. The data access time for the AD7893

is 50 ns from the rising edge of its SCLK input. Assuming a

10 ns propagation delay through the external AND gate, the

high time of the SCLK1 output of the ADSP-2105 must be

≥ (50 + 25 + 10 + 10) ns, i.e., ≥ 95 ns. This means that the

serial clock frequency with which the interface of Figure 13 can

work with is limited to 5.26 MHz.

An alternative scheme is to configure the ADSP-2105 to accept

an external serial clock. In this case, an external noncontinuous

serial clock that drives the serial clock inputs of both the ADSP-

2105 and the AD7893 is provided. In this scheme, the serial

clock frequency is limited to 5 MHz by the ADSP-2105.

To monitor the conversion time on the AD7893, a scheme such

as outlined in previous interfaces with CONVST can be used.

This can be implemented by connecting the CONVST line

directly to the IRQ2 input of the ADSP-2105.

AD7893–DSP56000 Interface

Figure 9 shows an interface circuit between the AD7893 and the

DSP56000 DSP processor. The DSP5600 is configured for nor-

mal mode asynchronous operation with gated clock. It is also set

up for a 16-bit word with the gated serial clock being generated

by the DSP56000 and appears on the SC0 pin. The SC0 pin

should be configured as an output by setting bit SCD0 to 1. In

this mode, the DSP56000 provides sixteen serial clock pulses to

the AD7893 in a serial read operation. The DSP56000 assumes

valid data on the first falling edge of SCK, so the interface is

simply two-wire as shown in Figure 9.

To monitor the conversion time on the AD7893, a scheme such

as outlined in previous interface examples with CONVST can

be used. This can be implemented by connecting the CONVST

line directly to the IRQA input of the DSP56000.

AD7893

SDATA

SCLK

DSP56000

SC0

SRD

Figure 9. AD7893 to DSP56000 Interface

AD7893 PERFORMANCE

Linearity

The linearity of the AD7893 is determined by the on-chip 12-bit

D/A converter. This is a segmented DAC that is laser trimmed

for 12-bit integral linearity and differential linearity. Typical

relative numbers for the part are ±1/4 LSB, while the typical

DNL errors are ±1/2 LSB.

Noise

In an A/D converter, noise exhibits itself as code uncertainty in

dc applications and as the noise floor (in an FFT, for example)

in ac applications. In a sampling A/D converter like the AD7893,

all information about the analog input appears in the baseband

from dc to 1/2 the sampling frequency. The input bandwidth of

the track/hold exceeds the Nyquist bandwidth; therefore, an

antialiasing filter should be used to remove unwanted signals

above f

/2 in the input signal in applications where such signals

exist.

Figure 10 shows a histogram plot for 8192 conversions of a dc

input using the AD7893. The analog input was set at the center

of a code transition. The timing and control sequence used was

per Figure 3 where the optimum performance of the ADC was

achieved. It can be seen that almost all the codes appear in the

one output bin, indicating very good noise performance from

the ADC. The rms noise performance for the AD7893-2 for the

above plot was 87 µV. Since the analog input range, and hence

LSB size, on the AD7893-10 is eight times what it is for the

AD7893-2, the same output code distribution results in an out-

put rms noise of 700 µV for the AD7893-10.

CODE

9000

1000

(X–4) (X–3)

OCCURRENCES OF CODE

(X–2) (X–1) X (X+1) (X+2) (X+3) (X+4)

8000

5000

4000

3000

2000

7000

6000

SAMPLING FREQUENCY = 102.4kHz

= +25

Figure 10. Histogram of 8192 Conversions of a DC Input

AD7893

–11–

REV. E

Effective Number of Bits

The formula for signal to (noise + distortion) ratio (see Termi-

nology section) is related to the resolution or number of bits in

the converter. Rewriting the formula gives a measure of perfor-

mance expressed in effective number of bits (N):

N = (SNR – 1.76) / 6.02

where SNR is Signal to (Noise + Distortion) Ratio.

The effective number of bits for a device can be calculated from

its measured signal to (noise + distortion) ratio. Figure 13 shows

a typical plot of effective number of bits versus frequency for the

AD7893-2 from dc to f

SAMPLING

/2. The sampling frequency is

102.4 kHz. The plot shows that the AD7893 converts an input

sine wave of 51.2 kHz to an effective numbers of bits of 11,

which equates to a signal to (noise + distortion) level of 68 dB.

INPUT FREQUENCY – kHz

12.0

11.5

10.0 0 51.225.6

EFFECTIVE NUMBER OF BITS

11.0

10.5

Figure 13. Effective Number of Bits vs. Frequency

The same data is presented in Figure 11 as in Figure 10 except

that, in this case, the output data read for the device occurs dur-

ing conversion. This has the effect of injecting noise onto the die

while bit decisions are being made; this increases the noise gen-

erated by the AD7893. The histogram plot for 8192 conversions

of the same dc input now shows a larger spread of codes with

the rms noise for the AD7893-2 increasing to 210 µV. This ef-

fect will vary depending on where the serial clock edges appear

with respect to the bit trials of the conversion process. It is pos-

sible to achieve the same level of performance when reading

during conversion as when reading after conversion, depending

on the relationship of the serial dock edges to the bit trial points.

CODE

7500

(X–4) (X–3)

OCCURRENCES OF CODE

7000

6500

6000

5500

5000

4500

4000

3500

3000

2500

2000

1500

1000

500

(X–2) (X–1) (X+1) (X+2) (X+3) (X+4)X

SAMPLING

FREQUENCY = 102.4kHz

= +25

Figure 11. Histogram of 8192 Conversions with Read Dur-

ing Conversion

Dynamic Performance

With a combined conversion and acquisition time of 7.5 µs, the

AD7893 is ideal for wide bandwidth signal processing applica-

tions. These applications require information on the ADC’s

effect on the spectral content of the input signal. Signal to (noise

+ distortion) ratio, total harmonic distortion, peak harmonic or

spurious noise, and intermodulation distortion are all specified.

Figure 12 shows a typical FFT plot of a 10 kHz, 0 V to +2.5 V

input after being digitized by the AD7893-2, operating at a

102.4 kHz sampling rate. The signal to (noise + distortion)

ratio is 71.5 dB, and the total harmonic distortion is –83 dB.

FREQUENCY – kHz

SNR IS SIGNAL TO (NOISE AND DISTORTION) RATIO

–30

–180 0 51.225.6

SIGNAL AMPLITUDE – dB

–60

–80

–120

SAMPLE RATE = 102.4kHz

INPUT FREQUENCY = 10kHz

SNR = 71.5dB

= +25°C

Figure 12. AD7893 FFT Plot

AD7893

REV. E

–12–

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

PRINTED IN U.S.A. C1787c–2–1/97

Plastic DIP (N-8)

PIN 1 0.280 (7.11)

0.240 (6.10)

SEATING

PLANE

0.060 (1.52)

0.015 (0.38)

0.130

(3.30)

MIN

0.210

(5.33)

MAX

0.160 (4.06)

0.115 (2.93)

0.430 (10.92)

0.348 (8.84)

0.022 (0.558)

0.014 (0.356) 0.070 (1.77)

0.045 (1.15)

0.100

(2.54)

BSC

0.325 (8.25)

0.300 (7.62)

0.015 (0.381)

0.008 (0.204)

0.195 (4.95)

0.115 (2.93)

Cerdip (Q-8)

0.320 (8.13)

0.290 (7.37)

0.015 (0.38)

0.008 (0.20)

0.005 (0.13) MIN 0.055 (1.4) MAX

PIN 1

0.310 (7.87)

0.220 (5.59)

0.405 (10.29) MAX

0.200

(5.08)

MAX

SEATING

PLANE

0.023 (0.58)

0.014 (0.36) 0.070 (1.78)

0.030 (0.76)

0.060 (1.52)

0.015 (0.38)

0.150

(3.81)

MIN

0.200 (5.08)

0.125 (3.18)

0.100

(2.54)

BSC

SOIC (SO-8)

0.0098 (0.25)

0.0075 (0.19)

0.0500 (1.27)

0.0160 (0.41)

0.0196 (0.50)

0.0099 (0.25) x 45

PIN 1

0.1574 (4.00)

0.1497 (3.80)

0.2440 (6.20)

0.2284 (5.80)

0.0192 (0.49)

0.0138 (0.35)

0.0500

(1.27)

BSC

0.0688 (1.75)

0.0532 (1.35)

0.0098 (0.25)

0.0040 (0.10)

0.1968 (5.00)

0.1890 (4.80)

1 of 2

Package/Price Information

True Bipolar Input, Single Supply, 12-Bit, Serial 6 µs ADC in 8-Pin Package

Model Status Package

Description Pin

Count Temperature

Range

Price*

(1000-

4999)

5962-9475501MPA PRODUCTION CERDIP GLASS

SEAL 8 MILITARY $55.25

5962-9475502MPA PRODUCTION CERDIP GLASS

SEAL 8 MILITARY $55.25

AD7893ACHIPS-10 PRODUCTION CHIPS/DIE SALES - COMMERCIAL $7.20

AD7893ACHIPS-2 PRODUCTION CHIPS/DIE SALES - COMMERCIAL $7.20

AD7893ACHIPS-5 PRODUCTION CHIPS/DIE SALES - COMMERCIAL $7.20

AD7893AN-10 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $9.00

AD7893AN-2 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $9.00

AD7893AN-5 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $9.00

AD7893AR-10 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-10REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-

10REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-2 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-2REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-2REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-3 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-3REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-3REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-5 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-5REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

AD7893AR-5REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $9.00

2 of 2

* This price is provided for budgetary purposes as recommended list price in U.S. Dollars per unit in

the stated volume. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing. View

Pricing and Availability for further information.

AD7893BN-10 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $11.65

AD7893BN-2 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $11.66

AD7893BN-5 PRODUCTION PLASTIC/EPOXY DIP 8 COMMERCIAL $11.66

AD7893BR-10 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-10REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-2 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-2REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-2REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-5 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-5REEL PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893BR-5REEL7 PRODUCTION STD S.O. PKG

(SOIC) 8 COMMERCIAL $11.66

AD7893SQ-10 PRODUCTION CERDIP GLASS

SEAL 8 COMMERCIAL $42.08

AD7893SQ-2 PRODUCTION CERDIP GLASS

SEAL 8 COMMERCIAL $42.08

AD7893SQ-5 PRODUCTION CERDIP GLASS

SEAL 8 COMMERCIAL $42.08