WizFi210 Datasheet (Version 1.20) WizFi220 follows all of information described in this documents (c)2013 WIZnet Co., Ltd. All Rights Reserved. For more information, visit our website at http://www.wiznet.co.kr WizFi210 Datasheet (WIZnet Co., Ltd.) Certification Information CE for Class B ITE INFORMATION TO THE USER Hereby, WIZnet. Declares that these WizFi210 and WizFi220 are in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. WARNING: These are the class B products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC for Class B ITE INFORMATION TO THE USER These equipments have been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no Guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: These equipments may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. TELEC 010-100040 Equipment : Wireless Module Model : WizFi210 UFL antenna type, WizFi210 Chip antenna type Made in Korea KCC for Class B ITE INFORMATION TO THE USER (B) . Trade Name or Applicant : WIZnet Co., Ltd. Equipment Name : Wireless LAN Module Model Number : WizFi210 / WizFi220 Manufacturer / Country of Origin : WIZnet, Co., Ltd. / KOREA Certification Number : KCC-CRM-WWW-WIZFI210 / KCC-CRM-WWW-WIZFI220 WARNING: . WizFi210 Datasheet (WIZnet Co., Ltd.) Document Revision History Date Revision 2011-03-24 V1.0 Official Release V1.01 Changed Power Consumption and RF Output Power Added Auto Reconnect AT Command(AT+XAR) Added Certification Information V1.10 Changed Evaluation Board Changed GPIO number(HW Trigger, Button) Changed AT+XEHT Command Added Limited AP Feature Added WizFi220 Specs V1.11 Added Added Added Added Added 2012-10-24 V1.12 Added AT+WAUTO Option(2 for Limited AP mode) Added FAQ(Reducing the disassociation event) Removed unused AT Commands Removed some features for customizing f/w 2013-03-08 V1.13 Added AT+XRESET Command Added max/min power value of AT+WP command 2013-03-12 V1.14 Added explanation of AT+XRESET Command Added FAQ 2013-05-06 V1.2 Divided two documents, Datasheet for Hardware Engineer and Programmers' guide for Software Engineer. More detail information included in datasheet. 2011-05-24 2011-09-05 2012-01-11 Changes UART baud rate(460800, 921600bps) EXT_nRESET description FAQ AT+DHCPSRVR Command Product contents Information in this document is belived to be accurate and reliable. However, WIZnet does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. WIZnet reserves the right to make changes to information published in this document, including without limitation specifictions and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. WizFi210 Datasheet (WIZnet Co., Ltd.) <Contents> 1. Overview .......................................................................................................................... 1-1 2. Brief Specifications ........................................................................................................... 2-2 3. Block Diagram .................................................................................................................. 3-3 4. Pin Description ................................................................................................................. 4-4 4.1. Pin Map .......................................................................................................... 4-4 4.2. Pin Description ................................................................................................ 4-4 4.3. Factory Reset Timing Diagram ........................................................................ 4-7 5. EXT_nRESET guide ......................................................................................................... 5-8 6. RF Specification ............................................................................................................... 6-9 7. Power Consumption ....................................................................................................... 7-10 7.1. WizFi210 Mode 1(VDDRTC=VDD=3.3V, VDDIO=1.8V, Temp=25C) ............. 7-10 7.2. WizFi210 Mode 2(VDDRTC=VDD=3.3V, VDDIO=3.3V, Temp=25C) ............. 7-10 7.3. WizFi220 Mode 1(VDDRTC=VDD=3.3V, VDDIO=1.8V, Temp=25C) ............. 7-11 7.4. WizFi220 Mode 2(VDDRTC=VDD=3.3V, VDDIO=3.3V, Temp=25C) ............. 7-11 8. Dimension ...................................................................................................................... 8-12 8.1. Module Dimension ........................................................................................ 8-12 8.2. Recommended Footprint Dimension.............................................................. 8-13 9. Electrical characteristics ................................................................................................. 9-14 9.1. Operating Condition ...................................................................................... 9-14 9.2. Digital Input characteristics ............................................................................ 9-14 9.3. Digital Output characteristics ......................................................................... 9-14 9.4. Tri-State I/O characteristics ........................................................................... 9-15 9.5. RTC Input characteristics .............................................................................. 9-15 9.6. RTC Output characteristics............................................................................ 9-16 9.7. Internal 1.8V regulator characteristics ............................................................ 9-16 9.8. Communication Interface............................................................................... 9-16 9.8.1. UART Interface characteristics ............................................................... 9-16 9.8.2. SPI Interface characteristics ................................................................... 9-16 10.Reflow Condition ...................................................................................................... 10-18 11.Circuit guide for On-board FW upload .......................................................................... 11-19 12.Reference Schematic .................................................................................................. 12-20 WizFi210 Datasheet (WIZnet Co., Ltd.) <Table> TABLE 1 BRIEF SPECIFICATION........................................................................................................................2-2 TABLE 2 WIZFI210 PIN DESCRIPTION ...........................................................................................................4-7 TABLE 3 FACTORY RESET TIMING VALUE ..................................................................................................4-7 TABLE 4 RF SPECIFICATION ...............................................................................................................................6-9 TABLE 5 WIZFI210 MODE 1(VDDIO = 1.8V) ............................................................................................... 7-10 TABLE 6 WIZFI210 MODE 2(VDDIO = 3.3V) ............................................................................................... 7-10 TABLE 7 WIZFI220 MODE 1(VDDIO = 1.8V) ............................................................................................... 7-11 TABLE 8 WIZFI220 MODE 2(VDDIO = 3.3V) ............................................................................................... 7-11 TABLE 9 OPERATING CONDITION ................................................................................................................ 9-14 TABLE 10 DIGITAL INPUT CHARACTERISTICS ...................................................................................... 9-14 TABLE 11 DIGITAL OUTPUT CHARACTERISTICS .................................................................................. 9-14 TABLE 12 TRI-STATE I/O CHARACTERISTICS ........................................................................................ 9-15 TABLE 13 RTC INPUT CHRACTERISTICS .................................................................................................. 9-15 TABLE 14 RTC OUTPUT CHARACTERISTICS ......................................................................................... 9-16 TABLE 15 INTERNAL 1.8V REGULATOR CHARACTERISTICS ........................................................ 9-16 TABLE 16 SPI INTERFACE TIMING VALUE ................................................................................................ 9-17 TABLE 17 REFLOW CONDITION .................................................................................................................. 10-18 WizFi210 Datasheet (WIZnet Co., Ltd.) <Figure> FIGURE 1 WIZFI210 BLOCK DIAGRAM ..........................................................................................................3-3 FIGURE 2 WIZFI220 BLOCK DIAGRAM ..........................................................................................................3-3 FIGURE 3 WIZFI210 PIN MAP ..............................................................................................................................4-4 FIGURE 4 FACTORY RESET TIMING DIAGRAM ........................................................................................4-7 FIGURE 5 REFERENCE SCHEMATIC FOR EXT_NRESET ...................................................................5-8 FIGURE 6 MODULE DIMENSION .................................................................................................................... 8-12 FIGURE 7 RECOMMENDED FOOTPRINT DIMENSION ....................................................................... 8-13 FIGURE 8 SPI INTERFACE TIMING DIAGRAM ........................................................................................ 9-16 FIGURE 10 REFLOW CHART ......................................................................................................................... 10-18 FIGURE 11 REFERENCE SCHEMATIC FOR ON-BOARD FW UPLOAD ................................... 11-19 FIGURE 12 VIN = BATTERY, STANDBY MODE SUPPORT ............................................................... 12-20 FIGURE 13 VIN = DC ADAPTOR, ALWAYS ACTIVE .............................................................................. 12-20 WizFi210 Datasheet (WIZnet Co., Ltd.) 1. Overview WizFi210/220(hereinafter WizFi210) is a Wi-Fi module that provides the robust and stale Wi-Fi connectivity with low power consumption. WizFi210 performs all functions for Wi-Fi connectivity and TCP/IP processing. All you have to do is just sending commands to the module via serial interface. n Support 802.11b only n Serial interface u UART(up to 921Kbps baud rate) u SPI(up to 2.25MHz clock) n Support AT commands n Support to multi sockets up to 16 concurrently n Plenty of TCP/IP functions u n TCP, UDP, IP, ICMP, Ultra low power u Support to Sleep mode and Alarm input for waking up WizFi210 in sleep mode n Plenty of Security mode u WEP, WPA, WPA2PSK, Enterprise mode(example EAP-TLS and so on) n Support GPIOs n Hardware accelerator for AES and RC4 encryption/decryption n Plenty of Operation mode u Station mode(infrastructure) u Ad-hoc mode u Limited AP(Soft AP) mode without ethernet or Wifi interface for uplink WizFi210 DataSheet (WIZnet Co., Ltd.) 1-1 2. Brief Specifications Specifications Description Radio Protocol IEEE 802.11b/g/n Compatible Supported Data Rates 11, 5.5, 2, 1 Mbps (IEEE 802.11b) Modulation DSSS and CCK RF Operating Frequency 2.4 - 2.497 GHz Antenna Options Chip antenna and U.FL connector for external antenna Networking Protocols UDP, TCP/IP (IPv4), DHCP, ARP, DNS, HTTP/HTTPS Client and Server 1 Power Consumption Standby = 34.0 A(WizFi210), 35.0 A(WizFi220) (Typical) Receive = 125.0 mA(WizFi210), 125.0 mA(WizFi220) Transmit = 135.0 mA(WizFi210), 250.0 mA(WizFi220) RF Output Power (Typical) 8 1 dBm (WizFi210) 17 1.5 dBm (WizFi220) Security Protocols WEP, WPA/WPA2-PSK, Enterprise(EAP-FAST, EAP-TLS, EAP-TTLS, PEAP) 1 1 I/O Interface UART, SPI , WAKE, ALARM, GPIOs Power Source 3.3V Dimensions 32 x 23.5 x 3 mm Table 1 Brief Specification 1 A dedicated SW is for support to this function 1 1 WizFi210 DataSheet (WIZnet Co., Ltd.) 2-2 3. Block Diagram WizFi210 and WizFi220 have the same functions and capabilities except their RF Transmission Power. WizFi220 has extra PA inside for improving its RF Transmission Power. Figure 1 WizFi210 block diagram Figure 2 WizFi220 block diagram WizFi210 DataSheet (WIZnet Co., Ltd.) 3-3 4. Pin Description 4.1. Pin Map Figure 3 WizFi210 Pin map 4.2. Pin Description PIN NAME I/O IN BIAS 1 GND P NA 2 NA I Pull-up 3 NA O NA 4 NA I NA 5 NA I Pull-up 6 NA I Pull-up WizFi210 DataSheet (WIZnet Co., Ltd.) DESCRIPTION Ground 4-4 7 ALARM1 I NA Embedded Real Time Clock Wake Up Input 1 8 NA O NA 9 VBAT P NA Embedded Real Time Clock Power Supply 10 DC_DC_CNTL O NA VIN_3V3 Regulator Control Output 11 ALARM2 (*) I NA Embedded Real Time Clock Wake Up Input 2 12 ADC1 (*) I NA General Analog to Digital Converter 1 13 ADC2 (*) I NA General Analog to Digital Converter 2 14 NA I/O Pull-down 15 NA I/O Pull-down 16 NA I/O Pull-down 17 VOUT_1V8 (*) P NA Internal 1.8V Vout 18 GND P NA Ground 19 NA I/O Pull-down 20 NA I/O Pull-down 21 NA I/O Pull-down 22 GPIO10 I/O Pull-down General Purpose Input Out-put General Purpose Input Output Data Received Indicator to Host while using 23 GPIO19 (*) I/O Pull-down SPI This is OUTPUT, means HOST_WAKEUP, from WizFi210 24 GPIO20 I Pull-down General Purpose Input Output Factory Reset(Normal High) 25 GPIO21 I Pull-down Factory mode 1 : Limited AP & Web Server for configuration Factory mode 2 : Ad-hoc mode 26 NA IO Pull-down 27 SPI_MISO (*) O Pull-up SPI Slave Transmit Data Output to the HOST 28 SPI_CLK (*) I Pull-up SPI Slave Clock Input from the HOST WizFi210 DataSheet (WIZnet Co., Ltd.) 4-5 29 SPI_CS (*) I Pull-up SPI Slave Chip Select Input from the HOST 30 SPI_MOSI (*) I Pull-down 31 GND P NA Ground 32 VIN_3V3 P NA Single Supply Port 33 EN_1V8 I NA 34 VDDIO(**) P NA 35 EXT_nRESET I Pull-up 36 NA I/O Pull-down SPI Slave Receive Data Input from the HOST Internal 1.8V regulator enable port Active High All I/O voltage domain (can be tied to VIN_3V3 or tied to HOST I/O supply) 2 Module Hardware Reset Input Firmware Program Enable 37 GPIO27 (*) O Pull-down WizFi210/220 operate as firmware download mode, if this is HIGH at booting On normal mode, this should be LOW 38 NA I Pull-down 39 NA O Pull-down 40 UART0_TX O Pull-down 41 UART0_RTS O Pull-down 42 UART0_RX I Pull-down 43 UART0_CTS I Pull-down Universal Asynchronous Receiver Transmitter Output Universal Asynchronous Receiver Transmitter Request to Send Output Universal Asynchronous Receiver Transmitter Input Universal Asynchronous Receiver Transmitter Clear to Send Input Data mode / command mode status Indicator You can monitor this pin to know which mode is 44 GPIO31 (S_MODE) O Pull-down now. LOW : Data mode HIGH : Command mode 2 45 GPIO30 (S_RX) O Pull-down 46 GPIO29 (C_MODE) I Pull-down Serial Data Received Switch of Command mode or Data mode You can control this pin to switch some mode In case of WizFi220, after HW reset on EXT_nRESET, user should command, AT+XRESET inorder to initialize all memory and configuration inside WizFi220. 4-6 WizFi210 DataSheet (WIZnet Co., Ltd.) LOW : Data mode HIGH : Command mode AP Association status GPIO28 (S_ASSOCIAT E) O 48 GND P NA Ground 49 EXT-ANT IO NA External Antenna pad 47 Pull-down LOW : associated HIGH : disassociated Table 2 WizFi210 Pin Description 4.3. Factory Reset Timing Diagram Factory Mode 1 t1 t2 Factory Mode 2 Figure 4 Factory Reset Timing Diagram Variable Min Typ Max t1 200ms 300ms 500ms t2 200ms 300ms 500ms Table 3 Factory Reset Timing Value WizFi210 DataSheet (WIZnet Co., Ltd.) 4-7 5. EXT_nRESET guide EXT_nRESET pin is bidirectional. EXT_nRESET pin is an output right at power-on, and kept it asserted while the 32KHz crystal is stabilizing. Once crystal is stabilized, RESET is de-assert and it becomes an input. MCU does need to assert the signal if there is not any problem such as hang-up. Note: Minimum pulse width for reset is two 32KHz clock. Figure 5 Reference Schematic for EXT_nRESET EXT_nRESET signal is active low signal . It's an output during power up, and it notifies to host processor that WizFi210 device is out of power-on-reset. After power-on-reset, this pin becomes an input. To assert EXT_nRESET is required to initialize WizFi210 without Power-on-reset. But there are some difference between Power-on-reset and asserting EXT_nRESET. Power-on-reset clear and initialize all configuration information which is set in WizFi210, but asserting EXT-nRESET doesn't clear and initialize some configuration information. So, if user assert EXT_nRESET for initialization of WizFi210, user should place a command, "AT+XRESET" to WizFi210 for initialization of all configuration information successfully. WizFi210 DataSheet (WIZnet Co., Ltd.) 5-8 6. RF Specification Specification Description DSSS for 1, 2Mbps Modulation Technique Data Rate CCK for 5.5, 11Mbps IEEE 802.11b: 1, 2, 5.5 and 11Mbps -84dBm 1dB @ 11Mbps Receive Sensitivity -88dBm 1dB @ 5.5Mbps (U.FL Connector version) -90dBm 1dB @ 2Mbps -94dBm 1dB @ 1Mbps Transmit power WizFi 210 : 8dBm 1dB @ 11Mbps (U.FL Connector version) WizFi 220 : 17dBm 1.5dB @ 11Mbps USA: 2.400 ~ 2.483GHz Frequency Range Europe: 2.400 ~ 2.483GHz Japan: 2.400 ~ 2.497GHz China: 2.400 ~ 2.483GHz USA/Canada: 11 (1~11) Major Europe Countries: 13 (1~13) Operating Channels France: 4 (10~13) Japan: 14 for IEEE 802.11b (1~13 or 14th), 13 for IEEE 802.11g (1~13) Korea/China: 13 (1~13) U.FL External Antenna Support(CON) Antenna External Antenna Pad Support(EX) Chip Antenna (Optional) (CA) Table 4 RF Specification WizFi210 DataSheet (WIZnet Co., Ltd.) 6-9 7. Power Consumption 7.1. WizFi210 Mode 1(VDDRTC=VDD=3.3V, VDDIO=1.8V, Temp=25C) WizFi 210 Min Standby mode (Only VDDRTC is active) Type Max Unit 35 50 A 10 mA 125 130 mA 135 140 mA Idle mode (CPU running, WLAN disconnected) Receive (-81dBm RX sensitivity) Transmit (+8dBm at antenna port) Table 5 WizFi210 Mode 1(VDDIO = 1.8V) 7.2. WizFi210 Mode 2(VDDRTC=VDD=3.3V, VDDIO=3.3V, Temp=25C) WizFi 210 Standby mode (Only VDDRTC is active) Min Type Max Unit 35 50 A 11 mA 125 130 mA 135 140 mA Idle mode (CPU running, WLAN disconnected) Receive (-81dBm RX sensitivity) Transmit (+8dBm at antenna port) Table 6 WizFi210 Mode 2(VDDIO = 3.3V) WizFi210 DataSheet (WIZnet Co., Ltd.) 7-10 7.3. WizFi220 Mode 1(VDDRTC=VDD=3.3V, VDDIO=1.8V, Temp=25C) WizFi 220 Min Standby mode (Only VDDRTC is active) Type Max Unit 35 50 A 12 mA 125 130 mA 250 260 mA Idle mode (CPU running, WLAN disconnected) Receive (-81dBm RX sensitivity) Transmit (+8dBm at antenna port) Table 7 WizFi220 Mode 1(VDDIO = 1.8V) 7.4. WizFi220 Mode 2(VDDRTC=VDD=3.3V, VDDIO=3.3V, Temp=25C) WizFi 220 Standby mode (Only VDDRTC is active) Min Type Max Unit 35 50 A 13 mA 125 130 mA 250 260 mA Idle mode (CPU running, WLAN disconnected) Receive (-81dBm RX sensitivity) Transmit (+8dBm at antenna port) Table 8 WizFi220 Mode 2(VDDIO = 3.3V) WizFi210 DataSheet (WIZnet Co., Ltd.) 7-11 8. Dimension 8.1. Module Dimension Figure 6 Module Dimension WizFi210 DataSheet (WIZnet Co., Ltd.) 8-12 8.2. Recommended Footprint Dimension Figure 7 Recommended Footprint Dimension WizFi210 DataSheet (WIZnet Co., Ltd.) 8-13 9. Electrical characteristics 9.1. Operating Condition Min Typ Max Unit +85 C Operating Ambient Range -40 RTC Supply Voltage 1.2 3.3 3.6 V Single Supply Voltage 3.0 3.3 3.6 V Min Typ Max Unit 1.62 1.8 1.98 3 3.3 3.63 Table 9 Operating Condition 9.2. Digital Input characteristics IO Supply Voltage V Input Low Voltage (VIL) -0.3 0.25VDDIO V Input High Voltage (VIH) 0.8VDDIO VDDIO V Schmitt trig. Low to High threshold point 1.5 (VT+) V Schmitt trig. High to Low threshold point (VT-) 1 V Unit Table 10 Digital Input Characteristics 9.3. Digital Output characteristics IO Supply Voltage Min Typ Max 1.62 1.8 1.98 3 3.3 3.63 V Output Low Voltage (VIL) 0 0.4 V Output High Voltage (VIH) 1.3 VDDIO V Output rise time (tTLH) 7 ns Output fall time (tTHL) 7 ns Table 11 Digital Output Characteristics WizFi210 DataSheet (WIZnet Co., Ltd.) 9-14 9.4. Tri-State I/O characteristics IO Supply Voltage Min Typ Max 1.62 1.8 1.98 3 3.3 3.63 Unit Input Low Voltage (VIL) -0.3 0.25VDDIO V Input High Voltage (VIH) 0.8VDDIO VDDIO V Schmitt trig. Low to High threshold point 1.5 (VT+) V Schmitt trig. High to Low threshold point (VT-) 1 V Pull-Up Resistor (Ru) 0.05 1 M Pull-Down Resistor (Rd) 0.05 1 V Output Low Voltage (VOL) 0 0.4 V Output High Voltage (VOH) 1.3 VDDIO V Output rise time @ 3.3V (tToLH) 7 ns Output fall time @ 3.3V (tToHL) 7 ns Input rise time (tTiLH) 7 ns Input fall time (tTiHL) 7 ns Max Unit Table 12 Tri-State I/O Characteristics 9.5. RTC Input characteristics Min Typ RTC Supply Voltage (VDDRTC) 1.2 3.6 V Input Low Voltage (VIL) -0.3 0.25VDDRTC V Input High Voltage (VIH) 0.8VDDRTC VDDRTC V 0.57VDDRTC 0.68VDDRTC V 0.27VDDRTC 0.35VDDRTC V Schmitt trig. Low to High threshold point (VT+) Schmitt trig. High to Low threshold point (VT-) Table 13 RTC Input Chracteristics WizFi210 DataSheet (WIZnet Co., Ltd.) 9-15 9.6. RTC Output characteristics Min Max Unit 1.2 3.6 V Output Low Voltage (VOL) 0 0.4 V Output High Voltage (VOH) 0.8VDDRTC VDDRTC V Output rise time (tTLH) 19 142 ns Output fall time (tTHL) 21 195 ns Max Unit RTC Supply Voltage (VDDRTC) Typ Table 14 RTC Output Characteristics 9.7. Internal 1.8V regulator characteristics Min Typ Output Voltage (VOUT_1V8) 1.8 Maximum Output Current (IVOUT_1V8) 250 1.8V Regulator Enable "H" Voltage Enable "L" Voltage (EN_1V8) 1.8V Regulator V 300 mA 1.0 VIN_3V3 V 0 0.25 V (EN_1V8) Table 15 Internal 1.8V Regulator Characteristics 9.8. Communication Interface 9.8.1. UART Interface characteristics 9.8.2. SPI Interface characteristics Figure 8 SPI Interface Timing Diagram WizFi210 DataSheet (WIZnet Co., Ltd.) 9-16 Parameter Description Minimum Maximum Unit tSSetup Minimum time between falling edge of Select line and first rising edge of SPI clock. 4 core SPI clock periods + 68 ns tTxdDelay Delay in Slave asserting TX line after falling edge of SPI clock, or the first bit after falling edge of the Select line. tRxdSetup Time before rising edge of SPI clock by which received data must be ready 15 tRxdHold Time for which received data must be stable after rising edge of SPI clock 3 core SPI clock periods + 14 ns mixed tSSHold Time for which the Select line will be held after the sampling edge for the final bit to be transferred 3 core SPI clock periods + 14 ns mixed mixed 4 core SPI clock periods + 68 ns mixed ns Table 16 SPI Interface Timing value WizFi210 DataSheet (WIZnet Co., Ltd.) 9-17 10. Reflow Condition Condition Pre-Heat Heating Recommend Range Unit 3 2~4 /s Pre-heat time (B) 130 60~180 sec Pre-heat ending temperature (C) 200 150~200 Peak Temperature range (D) 236 230~240 Melting time that is the time over 218 (E) 45 30~50 sec Temperature Ramp up rate for (A) Table 17 Reflow condition Figure 9 Reflow Chart WizFi210 DataSheet (WIZnet Co., Ltd.) 10-18 11. Circuit guide for On-board FW upload WizFi210 provides some specific firmware according to its services. Until now, there are four standard firmware and some customized firmware to specific customers. WizFi210 decides its operating mode according to the input value of GPIO27. WizFi210 operates as programming mode when GPIO27's input value is "HIGH", otherwise running mode. WizFi210 communicate with PC via UART in order to upload another firmware, so you have to connect UART0_Rx and UART0_Tx to the external interface for communicating with PC. So, we recommend that you make your board be capable to upload another firmware as Figure 7 below. Figure 10 Reference schematic for On-Board FW Upload WizFi210 DataSheet (WIZnet Co., Ltd.) 11-19 12. Reference Schematic Figure 11 VIN = Battery, Standby mode support Figure 12 VIN = DC Adaptor, Always active WizFi210 DataSheet (WIZnet Co., Ltd.) 12-20