LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 LM4819 350mW Audio Power Amplifier with Shutdown Mode Check for Samples: LM4819, LM4819MBD FEATURES DESCRIPTION * The LM4819 is a mono bridged power amplifier that is capable of delivering 350mWRMS output power into a 16 load or 300mWRMS output power into an 8 load with 10% THD+N from a 5V power supply. 1 2 * * * WSON, SOIC, and VSSOP Surface Mount Packaging Switch On/Off Click Suppression Unity-Gain Stable Minimum External Components KEY SPECIFICATIONS * * * THD+N at 1kHz, 350mW Continuous Average Output Power into 16: 10% (max) THD+N at 1kHz, 300mW Continuous Average Output Power into 8: 10% (max) Shutdown Current: 0.7A (typ) APPLICATIONS * * * The LM4819 Boomer audio power amplifier is designed specifically to provide high quality output power and minimize PCB area with surface mount packaging and a minimal amount of external components. Since the LM4819 does not require output coupling capacitors, bootstrap capacitors or snubber networks, it is optimally suited for low-power portable applications. The closed loop response of the unity-gain stable LM4819 can be configured using external gain-setting resistors. The device is available in WSON, VSSOP, and SOIC package types to suit various applications. General Purpose Audio Portable Electronic Devices Information Appliances (IA) Typical Application Figure 1. Typical Audio Amplifier Application Circuit Connection Diagrams 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2001-2013, Texas Instruments Incorporated LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Top View Top View Figure 2. Small Outline (SOIC) Package See Package Number D0008A Figure 3. Mini Small Outline (VSSOP) Package See Package Number DGK0008A Top View Figure 4. WSON Package See Package Number NGL0008B These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 Absolute Maximum Ratings (1) (2) (3) Supply Voltage 6.0V -65C to +150C Storage Temperature -0.3V to VDD +0.3V Input Voltage Power Dissipation (PD) (4) ESD Susceptibility Internally Limited (5) 3.5kV ESD Susceptibility (6) 250V Junction Temperature (TJ) Soldering Information 150C Small Outline Package Vapor Phase (60 seconds) 215C Infrared (15 seconds) Thermal Resistance (1) (2) (3) (4) (5) (6) (7) (8) 220C JC (VSSOP) 56C/W JA (VSSOP) 210C/W JC (SOIC) 35C/W JA (SOIC) 170C/W JA (WSON) 117C/W (7) JA (WSON) 150C/W (8) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication of device's performance. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA. For the LM4819, TJMAX = 150C and the typical junction-toambient thermal resistance (JA) when board mounted is 210C/W for the VSSOP package and 170C/W for the SOIC package. Human body model, 100pF discharged through a 1.5 k resistor. Machine Model, 220pF-240pF capacitor is discharged through all pins. The given JA is for an LM4819 package in an NGL0008B with the Exposed-DAP soldered to a printed circuit board copper pad with an area equivalent to that of the Exposed-DAP itself. The Exposed-DAP of the NGL0008B package should be electrically connected to GND or an electrically isolated copper area. The given JA is for an LM4819 package in an NGL0008B with the Exposed-DAP not soldered to any printed circuit board copper. Operating Ratings (1) (2) Temperature Range TMIN TA TMAX -40C TA 85C 2.0V VCC 5.5V Supply Voltage (1) (2) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication of device's performance. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 3 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Electrical Characteristics VDD = 5V (1) (2) The following specifications apply for VDD = 5V, RL = 16 unless otherwise stated. Limits apply for TA = 25C. Parameter LM4819 Test Conditions Typical (3) Limit (4) (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A 1.5 3.0 mA (max) ISD Shutdown Current VPIN1 = VDD (6) 1.0 5.0 A (max) VSDIH Shutdown Voltage Input High 4.0 V (min) VSDIL Shutdown Voltage Input Low VOS Output Offset Voltage PO Output Power THD+N Total Harmonic Distortion + Noise (1) (2) (3) (4) (5) (6) VIN = 0V 5 1.0 V (max) 50 mV (max) THD = 10%, fIN = 1kHz 350 mW THD = 10%, fIN = 1kHz, RL = 8 300 mW 1 % PO = 270mWRMS, AVD = 2, fIN = 1kHz All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication of device's performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by designs, test, or statistical analysis. The shutdown pin (pin1) should be driven as close as possible to VDD for minimum current in Shutdown Mode. Electrical Characteristics VDD = 3V (1) (2) The following specifications apply for VDD = 3V and RL = 16 load unless otherwise stated. Limits apply to TA = 25C. Parameter LM4819 Test Conditions Typical (3) Limit (4) (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A 1.0 3.0 mA (max) ISD Shutdown Current VPIN1 = VDD (6) 0.7 5.0 A (max) VSDIH Shutdown Voltage Input High 2.4 V (min) VSDIL Shutdown Voltage Input Low 0.6 V (max) VOS Output Offset Voltage PO Output Power THD+N Total Harmonic Distortion + Noise (1) (2) (3) (4) (5) (6) 4 VIN = 0V 5 50 mV THD = 10%, fIN = 1kHz 110 mW THD = 10%, fIN = 1kHz, RL = 8 90 mW PO = 80mWRMS, AVD = 2, fIN = 1kHz 1 % All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication of device's performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by designs, test, or statistical analysis. The shutdown pin (pin1) should be driven as close as possible to VDD for minimum current in Shutdown Mode. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 External Components Description (See Figure 1) Components Functional Description 1. Ri Combined with Rf, this inverting input resistor sets the closed-loop gain. Ri also forms a high pass filter with Ci at fc = 1/(2RiCi). 2. Ci This input coupling capacitor blocks DC voltage at the amplifier's terminals. Combined with Ri, it creates a high pass filter with Ri at fc = 1/(2RiCi). Refer to the section, Proper Selection of External Components for an explanation of how to determine the value of Ci. 3. Rf Combined with Ri, this is the feedback resistor that sets the closed-loop gain: Av = 2(RF/Ri). 4. CS This is the power supply bypass capacitor that filters the voltage applied to the power supply pin. Refer to the Application Information section for proper placement and selection of Cs. 5. CB This is the bypass pin capacitor that filters the voltage at the BYPASS pin. Refer to the section, Proper Selection of External Components, for information concerning proper placement and selection of CB. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 5 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics 6 THD+N vs Frequency THD+N vs Frequency Figure 5. Figure 6. THD+N vs Frequency THD+N vs Frequency Figure 7. Figure 8. THD+N vs Frequency THD+N vs Frequency Figure 9. Figure 10. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 Typical Performance Characteristics (continued) THD+N vs Output Power THD+N vs Output Power Figure 11. Figure 12. THD+N vs Output Power THD+N vs Output Power Figure 13. Figure 14. THD+N vs Output Power THD+N vs Output Power Figure 15. Figure 16. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 7 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) 8 Output Power vs Supply Voltage RL = 8 Output Power vs Supply Voltage RL = 16 Figure 17. Figure 18. Output Power vs Supply Voltage RL = 32 Output Power vs Load Resistance Figure 19. Figure 20. Power Dissipation vs Output Power VDD = 5V Power Dissipation vs Output Power VDD = 3V Figure 21. Figure 22. Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Power Derating Curves Frequency Response vs Input Capacitor Size Figure 23. Figure 24. Supply Current vs Supply Voltage Figure 25. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 9 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com APPLICATION INFORMATION BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4819 consists of two operational amplifiers. External resistors, Ri and RF set the closed-loop gain of the first amplifier (and the amplifier overall), whereas two internal 20k resistors set the second amplifier's gain at -1. The LM4819 is typically used to drive a speaker connected between the two amplifier outputs. Figure 1 shows that the output of Amp1 servers as the input to Amp2, which results in both amplifiers producing signals identical in magnitude but 180 out of phase. Taking advantage of this phase difference, a load is placed between V01 and V02 and driven differentially (commonly referred to as "bridge mode"). This results in a differential gain of AVD= 2 *(Rf/Ri) (1) Bridge mode is different from single-ended amplifiers that drive loads connected between a single amplifier's output and ground. For a given supply voltage, bridge mode has a distinct advantage over the single-ended configuration: its differential output doubles the voltage swing across the load. This results in four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output assumes that the amplifier is not current limited or the output signal is not clipped. To ensure minimum output signal clipping when choosing an amplifier's closed-loop gain, refer to the Audio Power Amplifier Design Example section. Another advantage of the differential bridge output is no net DC voltage across the load. This results from biasing V01 and V02 at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a single-ended configuration forces a single supply amplifier's half-supply bias voltage across the load. The current flow created by the half-supply bias voltage increases internal IC power dissipation and may permanently damage loads such as speakers. POWER DISSIPATION Power dissipation is a major concern when designing a successful bridged or single-ended amplifier. Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified load. PDMAX = (VDD)2 /(22RL ) (W) Single-ended (2) However, a direct consequence of the increased power delivered to the load by a bridged amplifier is an increase in the internal power dissipation point for a bridge amplifier operating at the same given conditions. Equation 3 states the maximum power dissipation point for a bridged amplifier operating at a given supply voltage and driving a specified load. PDMAX = 4(VDD)2/(22 RL ) (W) Bridge Mode (3) The LM4819 has two operational amplifiers in one package and the maximum internal power dissipation is four times that of a single-ended amplifier. However, even with this substantial increase in power dissipation, the Lm4819 does not require heatsinking. From Equation 3, assuming a 5V power supply and an 8 load, the maximum power dissipation point is 633mW. The maximum power dissipation point obtained from Equation 3 must not exceed the power dissipation predicted by Equation 4: PDMAX = (TJMAX - TA)/JA (W) (4) For the micro DGK0008A package, JA = 210C/W, for the D0008A package, JA = 170C/W , and TJMAX = 150C for the LM4819. For a given ambient temperature, TA, Equation 4 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 3 is greater than the result of Equation 4, then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. For a typical application using the D0008A packaged LM4819 with a 5V power supply and an 8 load, the maximum ambient temperature that does not violate the maximum junction temperature is approximately 42C. If a DGK0008A packaged part is used instead with the same supply voltage and load, the maximum ambient temperature is 17C. In both cases, it is assumed that a device is a surface mount part operating around the maximum power dissipation point. The assumption that the device is operating around the maximum power dissipation point is incorrect for an 8 load. The maximum power dissipation point occurs when the output power is equal to the maximum power dissipation or 50% efficiency. The LM4819 is not capable of the output power level (633mW) required to operate at the maximum power dissipation point for an 8 load. To find the maximum power dissipation, the graph Figure 22 must be used. From the graph, the maximum power dissipation for an 8 10 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 load and a 5V supply is approximately 575mW. Substituting this value back into Equation 4 for PDMAX and using JA = 210C/W for the DGK0008A package, the maximum ambient temperature is calculated to be 29C. Using JA = 170C/W for the D0008A package, the maximum ambient temperature is 52C. Refer to the Typical Performance Characteristics curves for power dissipation information for lower output powers and maximum power dissipation for each package at a given ambient temperature. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitors connected to the bypass and power supply pins should be placed as close to the LM4819 as possible. The capacitor connected between the bypass pin and ground improves the internal bias voltage's stability, producing improved PSRR. The improvements to PSRR increase as the bypass pin capacitor value increases. Typical applications employ a 5V regulator with 10F and 0.1F filter capacitors that aid in supply stability. Their presence, however, does not eliminate the need for bypassing the supply nodes of the LM4819. The selection of bypass capacitor values, especially CB , depends on desired PSRR requirements, click and pop performance as explained in the section, Proper Selection of External Components, as well as system cost and size constraints. SHUTDOWN FUNCTION The voltage applied to the LM4819's SHUTDOWN pin controls the shutdown function. Activate micro-power shutdown by applying VDD to the SHUTDOWN pin. When active, the LM4819's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The logic threshold is typically 1/2VDD. The low 0.7A typical shutdown current is achieved by applying a voltage that is as near as VDD as possible to the SHUTDOWN pin. A voltage that is less than VDD may increase the shutdown current. Avoid intermittent or unexpected micro-power shutdown by ensuring that the SHUTDOWN pin is not left floating but connected to either VDD or GND. There are a few ways to activate micro-power shutdown. These included using a single-pole, single-throw switch, a microcontroller, or a microprocessor. When using a switch, connect an external 10k to 100k pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier operation by closing the switch. Opening the switch connects the shutdown pin to VDD through the pull-up resistor, activating micro-power shutdown. The switch and resistor ensure that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or a microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor PROPER SELECTION OF EXTERNAL COMPONENTS Optimizing the LM4819's performance requires properly selecting external components. Though the LM4819 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. The LM4819 is unity gain stable, giving the designer maximum design flexibility. The gain should be set to no more than a given application requires. This allows the amplifier to achieve minimum THD+N and maximum signal-to-noise ratio. These parameters are compromised as the closed-loop gain increases. However, low gain demands input signals with greater voltage swings to achieve maximum output power. Fortunately, many signal sources such as audio CODECs have outputs of 1VRMS (2.83VP-P). Please refer to the Audio Power Amplifier Design section for more information on selecting the proper gain. Another important consideration is the amplifier's close-loop bandwidth. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, Ci, forms a first order high pass filter that limits low frequency response. This value should be chosen based on needed frequency response for a few distinct reasons discussed below Input Capacitor Value Selection Amplifying the lowest audio frequencies requires a high value input coupling capacitor (Ci in Figure 1). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with limited frequency response reap little improvement by using a large input capacitor. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 11 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Besides affecting system cost and size, Ci has an effect on the LM4819's click and pop performance. When the supply voltage is first applied, a transient (pop) is created as the charge on the input capacitor changes from zero to a quiescent state. The magnitude of the pop is directly proportional to the input capacitor's value. Higher value capacitors need more time to reach a quiescent DC voltage (usually 1/2 VDD) when charged with a fixed current. The amplifier's output charges the input capacitor through the feedback resistor, RF. Thus, selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency can minimize pops. As shown in Figure 1, the input resistor (Ri) and the input capacitor, Ci produce a -3dB high pass filter cutoff frequency that is found using Equation 5. f-3dB = 1/(2 RiCi) (Hz) (5) As an example when using a speaker with a low frequency limit of 150Hz, Ci, using Equation 5 is 0.063F. The 0.39F Ci shown in Figure 1 allows the LM4819 to drive a high efficiency, full range speaker whose response extends down to 20Hz. Besides optimizing the input capacitor value, the bypass capacitor value, CB requires careful consideration. The bypass capacitor's value is the most critical to minimizing turn-on pops because it determines how fast the LM4819 turns on. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the smaller the turn-on pop. While the device will function properly (no oscillations or motorboating), with CB less than 1.0F, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to or greater than 1.0F is recommended in all but the most cost sensitive designs. Bypass Capacitor Value Selection Besides minimizing the input capacitor size, careful consideration should be paid to the value of CB, the capacitor connected to the BYPASS pin. Since CB determines how fast the LM4819 settles to quiescent operation, its value is critical when minimizing turn-on pops. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the smaller the turn-on pop. Choosing CB equal to 1.0F along with a small value of Ci (in the range of 0.1F to 0.39F) produces a click-less and pop-less shutdown function. As discussed above, choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops. Optimizing Click and Pop Reduction Performance The LM4819 contains circuitry that minimizes turn-on and shutdown transients or "clicks and pops". For this discussion, turn on refers to either applying the power or supply voltage or when the shutdown mode is deactivated. While the power supply is ramping to it's final value, the LM4819's internal amplifiers are configured as unity gain buffers. An internal current source charges the voltage of the bypass capacitor, CB, connected to the BYPASS pin in a controlled, linear manner. Ideally, the input and outputs track the voltage charging on the bypass capacitor. The gain of the internal amplifiers remains unity until the bypass capacitor is fully charged to 1/2VDD. As soon as the voltage on the bypass capacitor is stable, the device becomes fully operational. Although the BYPASS pin current cannot be modified, changing the size of the bypass capacitor, CB, alters the device's turn-on time and magnitude of "clicks and pops". Increasing the value of CB reduces the magnitude of turn-on pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time (Ton) increases. There is a linear relationship between the size of CB and the turn on time. Below are some typical turn-on times for various values of CB: 12 Submit Documentation Feedback CB TON 0.01F 20ms 0.1F 200ms 0.22F 440ms 0.47F 940ms 1.0F 2S Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 In order to eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD may not allow the capacitors to fully discharge, which may cause "clicks and pops". AUDIO POWER AMPLIFIER DESIGN EXAMPLE The following are the desired operational parameters: Given: Power Output 100mW Load Impedance 16 Input Level 1Vrms (max) Input Impedance 20k Bandwidth 100Hz-20kHz 0.25dB The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. To find this minimum supply voltage, use the Output Power vs. Supply Voltage graph in the Typical Performance Characteristics section. From the graph for a 16 load, (graphs are for 8, 16, and 32 loads) the supply voltage for 100mW of output power with 1% THD+N is approximately 3.15 volts. Additional supply voltage creates the benefit of increased headroom that allows the LM4819 to reproduce peaks in excess of 100mW without output signal clipping or audible distortion. The choice of supply voltage must also not create a situation that violates maximum dissipation as explained above in the Power Dissipation section. For example, if a 3.3V supply is chosen for extra headroom then according to Equation 3 the maximum power dissipation point with a 16 load is 138mW. Using Equation 4 the maximum ambient temperature is 121C for the DGK0008A package and 126C for the D0008A package. After satisfying the LM4819's power dissipation requirements, the minimum differential gain is found using Equation 6. (6) Thus a minimum gain of 1.27 V/V allows the LM4819 to reach full output swing and maintain low noise and THD+N performance. For this example, let AVD = 1.27. The amplifier's overall gain is set using the input (Ri) and feedback (RF) resistors. With the desired input impedance set to 20k, the feedback resistor is found using Equation 7. RF/Ri = AVD/2 (V/V) (7) The value of RF is 13k. The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired 0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth limit. The gain variation for both response limits is 0.17dB, well with in the 0.25dB desired limit. The results are: fL = 100Hz/5 = 20Hz fH = 20 kHz*5 = 100kHz As mentioned in the External Components section, Ri and Ci create a high pass filter that sets the amplifier's lower band pass frequency limit. Find the coupling capacitor's value using Equation 8. Ci 1/(2Rifc) (F) (8) Ci 0.398F, a standard value of 0.39F will be used. The product of the desired high frequency cutoff (100kHz in this example) and the differential gain, AVD, determines the upper pass band response limit. With AVD = 1.27 and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 127kHz. This is less than the LM4819's 900kHz GBWP. With this margin the amplifier can be used in designs that require more differential gain while avoiding performance restricting bandwidth limitations. Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 13 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Figure 26. Higher Gain Audio Amplifier The LM4819 is unity-gain stable and requires no external components besides gain-setting resistors, an input coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential gain of greater than 10 is required, a feedback capacitor (C4) may be needed as shown in Figure 26 to bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that eliminates possible high frequency oscillations. Care should be taken when calculating the -3dB frequency in that an incorrect combination of R3 and C4 will cause rolloff before 20kHz. A typical combination of feedback resistor and capacitor that will not produce audio band high frequency rolloff is R3 = 20k and C4 = 25pF. These components result in a -3dB point of approximately 320 kHz. It is not recommended that the feedback resistor and capacitor be used to implement a band limiting filter below 100kHz. Figure 27. Differential Amplifier Configuration for LM4819 14 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 Figure 28. Reference Design Board and PCB Layout Guidelines LM4819 SOIC DEMO BOARD ARTWORK Figure 29. Silk Screen Figure 30. Top Layer Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 15 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Figure 31. Bottom Layer LM4819 VSSOP DEMO BOARD ARTWORK Figure 32. Silk Screen Figure 33. Top Layer 16 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 Figure 34. Bottom Layer LM4819 WSON DEMO BOARD ARTWORK Composite View Top Layer Silk Screen Bottom Layer Table 1. Mono LM4819 Reference Design Boards Bill of Material for all Demo Boards Item Part Number Part Description Qty Ref Designator 1 551011208-001 LM4819 Mono Reference Design Board 1 10 482911183-001 LM4819 Audio AMP 1 U1 20 151911207-001 Tant Cap 1uF 16V 10 1 C1 Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 17 LM4819, LM4819MBD SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 www.ti.com Table 1. Mono LM4819 Reference Design Boards Bill of Material for all Demo Boards (continued) Item Part Number Part Description Qty Ref Designator 21 151911207-002 Cer Cap 0.39uF 50V Z5U 20% 1210 1 C2 25 152911207-001 Tant Cap 1uF 16V 10 1 C3 30 472911207-001 Res 20K Ohm 1/10W 5 3 R1, R2, R3 35 210007039-002 Jumper Header Vertical Mount 2X1 0.100 2 J1, J2 PCB LAYOUT GUIDELINES This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power and ground traces. Designers should note that these are only "rule-of-thumb" recommendations and the actual results will depend heavily on the final layout. General Mixed Signal Layout Recommendation Power and Ground Circuits For two layer mixed signal design, it is important to isolate the digital power and ground trace paths from the analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even device. This technique will take require a greater amount of design time but will not increase the final price of the board. The only extra parts required will be some jumpers. Single-Point Power / Ground Connections The analog power traces should be connected to the digital traces through a single point (link). A "Pi-filter" can be helpful in minimizing high frequency noise coupling between the analog and digital sections. It is further recommended to put digital and analog power traces over the corresponding digital and analog ground traces to minimize noise coupling. Placement of Digital and Analog Components All digital components and high-speed digital signals traces should be located as far away as possible from analog components and circuit traces. Avoiding Typical Design / Layout Problems Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90 degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise coupling and cross talk. 18 Submit Documentation Feedback Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD LM4819, LM4819MBD www.ti.com SNAS133D - FEBRUARY 2001 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision C (March 2013) to Revision D * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Copyright (c) 2001-2013, Texas Instruments Incorporated Product Folder Links: LM4819 LM4819MBD Submit Documentation Feedback 19 PACKAGE OPTION ADDENDUM www.ti.com 11-Sep-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM4819LD/NOPB ACTIVE WSON NGL 8 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 G19 LM4819MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 G19 LM4819MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 G19 LM4819MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM48 19M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Sep-2016 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4819LD/NOPB WSON NGL 8 1000 178.0 12.4 2.8 2.8 1.0 8.0 12.0 Q1 LM4819MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM4819MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM4819MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4819LD/NOPB WSON NGL 8 1000 210.0 185.0 35.0 LM4819MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LM4819MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LM4819MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NGL0008B LDA08B (Rev B) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4819LD LM4819LD/NOPB LM4819LDX LM4819LDX/NOPB LM4819MM LM4819MM/NOPB LM4819MMX LM4819MMX/NOPB LM4819MX/NOPB