184333J100AAB - Cornell Dubilier Electronics, Inc.

Type 167/184 Metallized Polyester Radial Lead Capacitors

Specifications

Radial Box Metallized Polyester Capacitors for Automatic Insertion

Highlights

♦ Rugged plastic case

♦ Case and epoxy fill meets UL94V0

♦ 7.5 mm (0.3”) lead spacing

♦ Bulk, tape and reel or ammo pack

♦ Non-inductively wound

♦ Non-polar

Capacitance Range:

Voltage Range:

Capacitance Tolerance:

Operating Temperature Range:

Dielectric Withstand Voltage:

Dissipation Factor (DF):

0.001 µF to 1.0 µF

63 Vdc to 630 Vdc (40 Vac to 220 Vac, 60 Hz)

±5%, ±10%, ±20%

–55 ºC to +125 ºC (with 50% Vdc derating >85 ºC)

1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC

tgδ x 10 –4 at 25 ºC ±5 ºC

The Type 167/184 series radial lead metallized polyester

box capacitors are available in bulk (Type 167) or on ammo

pack or radial tape and reel (Type 184). These capacitors

are constructed in rugged rectangular plastic cases and all

come with 7.5 mm (0.3”) lead spacing. They are good for

general purpose applications such as bypass, decoupling,

energy storage/discharge and arc suppression.

Total Self Inductance (L):

Maximum Pulse Rise Time (dv/dt):

Long Term Stability (after two years):Capacitance change ∆C/C ≤ ±3% under standard

environmental conditions

If the working voltage (V) is less than the nominal voltage (Vn),

the capacitor can work at higher dv/dt. In this case, the maxi-

mum value allowed is obtained by multiplying the above value

with the ratio Vn/V.

kHz tgδ x 10

–4

1≤100

10 ≤150

Approximately 8 nH

Vn V/ms

63 12

100 20

250 32

400 41

630 70

1.002

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 167/184 Metallized Polyester Radial Lead Capacitors

Outline Drawing

Ratings

Test Method and Performance

Max

±.015

(±0.4 mm)

.217 ±.039

(5.5 ±1.0 mm)

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications)

Test Conditions

Soldering Temperature 260 ºC ±5 ºC

Soldering Duration 10 sec ±1 sec

Performance

Capacitance Change ∆C/C ≤ ±2%

DF Change ∆tgδ≤

30 x 10–4 at 10 kHz

Insulation Resistance ≥ limit value

Soldering

Test Conditions

Temperature 25 ºC ±5 ºC

Voltage Charge Time 1 minute

Voltage Charge 50 Vdc for Vn < 100 Vdc

100 Vdc for Vn ≥ 100 Vdc

Performance

For Vn > 100 Vdc ≥30,000 MΩ (50,000 MΩ typical)

For Vn ≤100 Vdc ≥10,000 MΩ for C ≤ 0.1µF

≥1,000 MΩ x µF for ≤ 0.1µF

Test Conditions

Temperature +40 ºC

Relative Humidity 95%

Test Duration 21 days

Performance

Capacitance Change ∆C/C ≤ ±5%

DF Change ∆tgδ≤

50 x 104 at 1 kHz

Insulation Resistance ≥ 50% of limit value

Test Conditions

Temperature +85 ºC

Test Duration 1000 hrs

Voltage Applied 1.25 x Vn

Performance

Capacitance Change ∆C/C ≤ ±5%

DF Change ∆tgδ≤

30 x 10–4 at 10 kHz

Insulation Resistance ≥ 50% of limit value

Insulation Resistance

Damp Heat Test

Life Test

Lead length shown is as supplied on 167 Series

Catalog Tape & Reel Cap

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

167683*63A 184683*63#A> 0.068 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167104*63A 184104*63#A> 0.10 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167154*63A 184154*63#A> 0.15 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167224*63A 184224*63#A> 0.22 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167274*63A 184274*63#A> 0.27 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167334*63A 184334*63#A> 0.33 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167474*63B 184474*63#B> 0.47 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167684*63C 184684*63#C> 0.68 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167105*63C 184105*63#C> 1.00 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167333*100A 184333*100#A> 0.033 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167473*100A 184473*100#A> 0.047 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167683*100A 184683*100#A> 0.068 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167104*100A 184104*100#A> 0.10 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167124*100B 184124*100#B> 0.12 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167154*100B 184154*100#B> 0.15 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167224*100C 184224*100#C> 0.22 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167334*100C 184334*100#C> 0.33 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

Inches Millimeters

63 Vdc / 40 Vac

100 Vdc / 63 Vac

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 167/184 Metallized Polyester Radial Lead Capacitors

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification)

167 104 K 100 A

Case

Series Capacitance Tolerance Voltage Code

167 392 = .0039 µF J = ±5% 63 = 63 Vdc A

103 = .01 µF K = ±10% 100 = 100 Vdc B

104 = .1 µF M = ±20% 250 = 250 Vdc C

105 = 1.0 µF 630 = 630 Vdc D

Part Numbering System for Bulk Items

Catalog Tape & Reel Cap

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

167103*250A 184103*250#A> 0.01 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167153*250A 184153*250#A> 0.015 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167183*250A 184183*250#A> 0.018 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167223*250A 184223*250#A> 0.022 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167273*250B 184273*250#B> 0.027 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167333*250B 184333*250#B> 0.033 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167393*250B 184393*250#B> 0.039 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167473*250B 184473*250#B> 0.047 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167683*250C 184683*250#C> 0.068 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167104*250C 184104*250#C> 0.1 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167472*400A 184472*400#A> 0.0047 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167562*400A 184562*400#A> 0.0056 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167682*400A 184682*400#A> 0.0068 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167103*400A 184103*400#A> 0.010 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167153*400B 184153*400#B> 0.015 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167223*400C 184223*400#C> 0.022 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167333*400C 184333*400#C> 0.033 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167102*630A 184102*630#A> $0.00 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167152*630A 184152*630#A> 0.0015 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167222*630A 184222*630#A> 0.0022 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167332*630A 184332*630#A> 0.0033 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6

167472*630B 184472*630#B> 0.0047 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167682*630B 184682*630#B> 0.0068 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6

167103*630C 184103*630#C> 0.010 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6

167153*630D 184153*630#D> 0.015 0.413 0.236 0.472 0.295 0.024 10.5 6.0 12.0 7.5 0.6

630 Vdc / 220 Vac

Inches Millimeters

250 Vdc / 160 Vac

400 Vdc / 200 Vac

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 167/184 Metallized Polyester Radial Lead Capacitors

Tape Specification - 7.5 mm Lead Spacing

Case Quantity Quantity

Code Reeled Ammo Pack

A 1800 1500

B 1500 1500

C 1200 1000

D 1000 1000

Tooling

Code Millimeters Inches

A 16.5±0.75 .679±.030

B 18.5±0.75 .728±.030

C 16.0±0.75 .630±030

H Dimensions

> The H dimension depends on the

insertion equipment used. Specify

the proper tooling code as indicated

below.

Lead-Wire Diameter Ød 0.6+0.04 –0.01 .024±.001

Lead-to-Lead Distance P 7.5+0.6 –0.2 .295+.024 –.040

Feed Hole Pitch P012.7±0.3 .5±.012

Pitch of Component P112.7±1.0 .5±.039

Hole Center to Lead P28.95±0.7 .352±.028

Component Alignment, F-R ∆h0

±2.0 0±.079

Tape Width W 18+1.0 –0.1 .709+.039 –.004

Hold-down Tape Width W06.0 min .236 min

Hole Position W19.0+0.75 –0.05 .355+.030 –.001

Hold-down Tape Position W23.0 Max .118 Max

Height of Component H > >

from Tape Center

Feed Hole Diameter D04.0±0.3 .157±.012

Item Code Millimeters Inches

184 104 K 100 R A B

Packaging *Tooling

Type Case Code

Series Capacitance Tolerance Voltage (#) Code (>)

184 392 = .0039 µF J = ±5% 63 = 63 Vdc A = Ammo A A

103 = .01 µF K = ±10% 100 = 100 Vdc R = Tape & Reel B B

104 = .1 µF M = ±20% 250 = 250 Vdc C C

105 = 1.0 µF 630 = 630 Vdc D

Part Numbering System for Auto Insertion

* Tooling code (>) depends on the users insertion equipment requirements. See table for available options.

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com