Type 167/184 Metallized Polyester Radial Lead Capacitors Radial Box Metallized Polyester Capacitors for Automatic Insertion The Type 167/184 series radial lead metallized polyester box capacitors are available in bulk (Type 167) or on ammo pack or radial tape and reel (Type 184). These capacitors are constructed in rugged rectangular plastic cases and all come with 7.5 mm (0.3") lead spacing. They are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppression. Highlights Rugged plastic case Case and epoxy fill meets UL94V0 7.5 mm (0.3") lead spacing Bulk, tape and reel or ammo pack Non-inductively wound Non-polar Specifications 1.002 Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): 0.001 F to 1.0 F 63 Vdc to 630 Vdc (40 Vac to 220 Vac, 60 Hz) 5%, 10%, 20% -55 C to +125 C (with 50% Vdc derating >85 C) 1.6 x rated voltage for 2 sec @ +25 C 5 C tg x 10 -4 at 25 C 5 C kHz 1 10 tg x 10-4 100 150 Total Self Inductance (L): Approximately 8 nH Long Term Stability (after two years): Maximum Pulse Rise Time (dv/dt): Capacitance change C/C 3% under standard environmental conditions Vn 63 100 250 400 630 V/ms 12 20 32 41 70 If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V. CDE Cornell Dubilier*1605 E. Rodney French Blvd.*New Bedford, MA 02744*Ph: (508)996-8561*Fax: (508)996-3830* www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Test Method and Performance Outline Drawing T L Max Max H Max .217 .039 (5.5 1.0 mm) S .015 (0.4 mm) Lead length shown is as supplied on 167 Series Soldering Test Conditions Soldering Temperature Soldering Duration Performance Capacitance Change C/C DF Change tg Insulation Resistance 260 C 5 C 10 sec 1 sec 2% -4 30 x 10 at 10 kHz limit value Insulation Resistance Test Conditions Temperature 25 C 5 C Voltage Charge Time 1 minute Voltage Charge 50 Vdc for Vn < 100 Vdc 100 Vdc for Vn 100 Vdc Performance 30,000 M (50,000 M typical) For Vn > 100 Vdc For Vn 100 Vdc 10,000 M for C 0.1F 1,000 M x F for 0.1F Damp Heat Test Test Conditions Temperature +40 C Relative Humidity 95% Test Duration 21 days Performance Capacitance Change C/C 5% 4 DF Change tg 50 x 10 at 1 kHz Insulation Resistance 50% of limit value Life Test Test Conditions Temperature +85 C Test Duration 1000 hrs Voltage Applied 1.25 x Vn Performance Capacitance Change C/C 5% -4 DF Change tg 30 x 10 at 10 kHz Insulation Resistance 50% of limit value Ratings Catalog Part Number Tape & Reel Ammo Pack Cap (F) Inches Millimeters T H S Od L T H S 63 Vdc / 40 Vac 167683*63A 184683*63#A> 0.068 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167104*63A 184104*63#A> 0.10 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167154*63A 184154*63#A> 0.15 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167224*63A 184224*63#A> 0.22 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167274*63A 184274*63#A> 0.27 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167334*63A 184334*63#A> 0.33 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167474*63B 184474*63#B> 0.47 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 167684*63C 184684*63#C> 0.68 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 167105*63C 184105*63#C> 1.00 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 100 Vdc / 63 Vac 167333*100A 184333*100#A> 0.033 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167473*100A 184473*100#A> 0.047 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167683*100A 184683*100#A> 0.068 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167104*100A 184104*100#A> 0.10 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 167124*100B 184124*100#B> 0.12 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 167154*100B 184154*100#B> 0.15 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 167224*100C 184224*100#C> 0.22 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 167334*100C 184334*100#C> 0.33 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 * Indicates capacitance tolerance: J = 5%, K = 10%, M = 20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications) L Od 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 CDE Cornell Dubilier*1605 E. Rodney French Blvd.*New Bedford, MA 02744*Ph: (508)996-8561*Fax: (508)996-3830* www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Catalog Part Number Tape & Reel Ammo Pack Cap (F) 167103*250A 167153*250A 167183*250A 167223*250A 167273*250B 167333*250B 167393*250B 167473*250B 167683*250C 167104*250C 184103*250#A> 184153*250#A> 184183*250#A> 184223*250#A> 184273*250#B> 184333*250#B> 184393*250#B> 184473*250#B> 184683*250#C> 184104*250#C> 0.01 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.068 0.1 167472*400A 167562*400A 167682*400A 167103*400A 167153*400B 167223*400C 167333*400C 184472*400#A> 184562*400#A> 184682*400#A> 184103*400#A> 184153*400#B> 184223*400#C> 184333*400#C> 0.0047 0.0056 0.0068 0.010 0.015 0.022 0.033 167102*630A 167152*630A 167222*630A 167332*630A 167472*630B 167682*630B 167103*630C 167153*630D 184102*630#A> 184152*630#A> 184222*630#A> 184332*630#A> 184472*630#B> 184682*630#B> 184103*630#C> 184153*630#D> $0.00 0.0015 0.0022 0.0033 0.0047 0.0068 0.010 0.015 Inches T H 250 Vdc / 160 Vac 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.157 0.354 0.413 0.157 0.354 0.413 0.157 0.354 0.413 0.157 0.354 0.413 0.197 0.433 0.413 0.197 0.433 400 Vdc / 200 Vac 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.157 0.354 0.413 0.197 0.433 0.413 0.197 0.433 630 Vdc / 220 Vac 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.138 0.276 0.413 0.157 0.354 0.413 0.157 0.354 0.413 0.197 0.433 0.413 0.236 0.472 L Millimeters T H S S Od L Od 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.024 0.024 0.024 0.024 0.024 0.024 0.024 0.024 0.024 0.024 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 3.5 3.5 3.5 3.5 4.0 4.0 4.0 4.0 5.0 5.0 7.0 7.0 7.0 7.0 9.0 9.0 9.0 9.0 11.0 11.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.024 0.024 0.024 0.024 0.024 0.024 0.024 10.5 10.5 10.5 10.5 10.5 10.5 10.5 3.5 3.5 3.5 3.5 4.0 5.0 5.0 7.0 7.0 7.0 7.0 9.0 11.0 11.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.295 0.024 0.024 0.024 0.024 0.024 0.024 0.024 0.024 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 3.5 3.5 3.5 3.5 4.0 4.0 5.0 6.0 7.0 7.0 7.0 7.0 9.0 9.0 11.0 12.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 * Indicates capacitance tolerance: J = 5%, K = 10%, M = 20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification) Part Numbering System for Bulk Items 167 104 Series 167 Capacitance 392 = .0039 F 103 = .01 F 104 = .1 F 105 = 1.0 F K 100 Tolerance Voltage J = 5% 63 = 63 Vdc K = 10% 100 = 100 Vdc M = 20% 250 = 250 Vdc 630 = 630 Vdc A Case Code A B C D CDE Cornell Dubilier*1605 E. Rodney French Blvd.*New Bedford, MA 02744*Ph: (508)996-8561*Fax: (508)996-3830* www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Tape Specification - 7.5 mm Lead Spacing Item Code Lead-Wire Diameter Od Millimeters 0.6+0.04 -0.01 Inches .024.001 Case Quantity Quantity Code Reeled Ammo Pack 1800 1500 1200 1500 1500 1000 1000 1000 Feed Hole Pitch P P0 7.5 12.70.3 .295 .5.012 A B C Pitch of Component P1 12.71.0 .5.039 D Hole Center to Lead P2 0.7 8.95 .352 Component Alignment, F-R h 02.0 0.079 Tape Width Hold-down Tape Width W W0 18+1.0 -0.1 .709+.039 -.004 Hole Position W1 6.0 min 9.0+0.75 -0.05 .236 min .355+.030 -.001 Hold-down Tape Position W2 3.0 Max .118 Max Lead-to-Lead Distance +0.6 -0.2 +.024 -.040 .028 Height of Component H > > from Tape Center Feed Hole Diameter D0 4.00.3 .157.012 > The H dimension depends on the insertion equipment used. Specify the proper tooling code as indicated below. Tooling Code A B C H Dim e nsions Millim e te rs Inche s 16.50.75 .679.030 18.50.75 .728.030 16.00.75 .630030 Part Numbering System for Auto Insertion 184 104 K Series Capacitance Tolerance 184 392 = .0039 F J = 5% 103 = .01 F K = 10% 104 = .1 F M = 20% 105 = 1.0 F 100 Voltage 63 = 63 Vdc 100 = 100 Vdc 250 = 250 Vdc 630 = 630 Vdc R Packaging Type (#) A = Ammo R = Tape & Reel A Case Code A B C D B *Tooling Code (>) A B C * Tooling code (>) depends on the users insertion equipment requirements. See table for available options. CDE Cornell Dubilier*1605 E. Rodney French Blvd.*New Bedford, MA 02744*Ph: (508)996-8561*Fax: (508)996-3830* www.cde.com