ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) Nominal Input Voltage Max. Output Power Output Voltage Output Efficiency Current 120 to 277 Vac 40 W 20 to 42 Vdc 250 mA up to 87% 90C (measured to 1.4 A typical at the hot spot) CC Max. Case Temperature THD Power Factor Dimming Method Dimming Range Startup Time < 20% > 0.9 Forward-Phase, Reverse-Phase & 0 - 10V 1 - 100% (% of Iout) 400 ms CC: Constant Current TRIAC/ELV Dimmer + Dim - Dim ESSV series 0-10 V Dimmer + LEDs - LEDs Plastic Case: L 84 x W 40 x H 27 mm (L 3.30 x W 1.57 x H 1.06 in) Purple: + Dim White: Neutral ESSV series Black: Line Grey: - Dim Red: + LEDs Black: - LEDs Wiring Diagram FEATURES * Same features as ESS/ESST series but with 5VA flammability, UL Class P and a thermally-enhanced plastic case * Compatible with TRIAC (forward-phase or leading-edge), ELV (reverse-phase or trailing-edge) and 0-10 V dimmers * UL Class P * 90C maximum case hot spot temperature * Class 2 power supply * Lifetime: 50,000 hours at 70C case hot spot temperature (some models have higher lifetime. Check lifetime curves in page 6) * IP66-rated case with silicone-based potting * Protections: output open load, over-current and short-circuit (hiccup), and over-temperature with auto recovery * Conducted and radiated EMI: Compliant with FCC CFR Title 47 Part 15 Class B (120 Vac) and Class A (277 Vac) * Complies with ENERGY STAR(R), DLC (DesignLight Consortium(R)) and CA Title 24 technical requirements * Worldwide safety approvals CA Title 24 (c) ERP Power, LLC 1 APPLICATIONS * Indoor & outdoor * Recessed lighting (downlights) * Commercial & residential lighting * Architectural lighting * Office Lighting 5 ESSV Series Data Sheet Rev. April 2018 ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 1 - ORDERING INFORMATION ESSV-- Series Nominal *010 (3 - 10 W) Vin *015 (11 - 15 W) * W (120 to *020 (16 - 20 W) 277 Vac) *030 (21 - 30 W) *040 (31 - 40 W) Iout (mA) Vout Max. (Vdc) Ordering Part Number Input Voltage Range (Vac) ESSV010W-0250-42 120 to 277 Iout (mA) Max Vout Vout Vout Open Loop Output min Nom Max (no load) Power (Vdc) (Vdc) (Vdc) Voltage (Vdc) (W) ESSV010W: up to 10 W 250 10.5 24 37.8 42 50 37.8 42 50 37.8 42 50 37.8 37.8 37.8 42 42 42 50 50 50 37.8 24.3 42 27 50 35 ESSV015W: 11 to 15 W ESSV015W-0300-42 120 to 277 300 12.6 24 ESSV020W: 16 to 20 W ESSV020W-0400-42 120 to 277 ESSV030W-0500-42 ESSV030W-0620-42 ESSV030W-0700-42 120 to 277 120 to 277 120 to 277 400 16.8 24 ESSV030W: 21 to 30 W 500 620 700 21.0 26.0 29.4 24 24 24 ESSV040W: 31 to 40 W ESSV040W-0900-42 ESSV040W-1400-27 120 to 277 120 to 277 900 1400 37.8 37.8 24 20 For additional options of output current and output voltage, contact your sales representative or send an email to SaveEnergy@erp-power.com. SaveEnergy@erp-power.com 2 www.erp-power.com ESSV Series ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 2 - INPUT SPECIFICATION (@25C ambient temperature) Units Minimum Input Voltage Range (Vin) - ESSVxxxW models Vac Input Frequency Range - ESSVxxxW Hz Input Current (Iin) A Typical Maximum 90 120, 277 305 47 60 63 0.35 A @ 120 Vac 0.18 A @ 277 Vac Power Factor (PF) 0.9 Inrush Current A Leakage Current A Input Harmonics ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 > 0.9 At nominal input voltage and with nominal LED voltage For derivative models < 10W, PF 0.8 at 277 Vac only For derivative models < 5W, PF 0.7 at 277 Vac only 120 Vac 277 Vac 3.6 9.7 5.9 16.7 3.2 9.0 4.6 13.0 5.0 16.3 Meets NEMA-410 requirements At any point on the sine wave and 25C 250 A @ 120 Vac 500 A @ 230 Vac Measured per IEC60950-1 600 A @ 277 Vac Complies with IEC61000-3-2 for Class C equipment Total Harmonics Distortion (THD) % Efficiency Isolation Notes The rated output current for each model is achieved at Vin108 Vac & at Vin198 Vac. At nominal load - up to 87% 20% At nominal input voltage and nominal LED voltage Complies with DLC (Design Light Consortium) technical requirements - Measured with nominal input voltage, a full sinusoidal wave form and without dimmer connected. Models in the ESSV010 and ESSV015 series have a nominal efficiency of 82%. The AC input to the main DC output is isolated and meets Class II reinforced/double insulation power supply 3 - OUTPUT SPECIFICATION (@25C ambient temperature) Output Voltage (Vout) Units Minimum Typical Maximum Vdc 20 42 See ordering information for details Output Current (Iout) mA 250 1400 Output Current Regulation % -5 5 Output Current Overshoot % - Ripple Current 40% of rated output current for each model Dimming Range (% of Iout) % Start-up Time ms 1 - 10 100 400 500 SaveEnergy@erp-power.com Notes See ordering information for details The rated output current for each model is achieved at Vin108 Vac & at Vin198 Vac. At nominal AC line voltage Includes load and current set point variations The driver does not operate outside of the regulation requirements for more than 500 ms during power on with nominal LED load and without dimmer. Measured at nominal LED voltage and nominal input voltage without dimming Calculated in accordance with the IES Lighting Handbook, 9th edition The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf (forward voltage). Dimming performance may vary when the driver is operated near its minimum output voltage. Measured from application of AC line voltage to the time where light is visible (about 10% of rated output current) Measured from application of AC line voltage to 100% light output Complies with California Title 24 and ENERGY STAR(R) luminaire specification 3 www.erp-power.com ESSV Series ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 4 - 0-10 V DIMMING CONTROL (@25C ambient temperature) Units Minimum Typical Maximum +Dim Signal, -Dim Signal Dimming Range (% of Iout) Current Supplied by the +Dim Signal Pin Output Current Tolerance While Being Dimmed Isolation Notes The ESSV series operate only with 0-10V dimmers that sink current. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim signal pins can be used to adjust the output setting via a standard commercial wall dimmer, an external control voltage source (0 to 10 Vdc), or a variable resistor when using the recommended number of LEDs. The dimming input permits 1% to 100% dimming. % 1 100 mA 1 % 8 The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf (forward voltage). Dimming performance may vary when the driver is operated near its minimum output voltage. The tolerance of the output current while being dimmed is +/-8% until down to 1V. The 0-10 V circuit is isolated from the AC input and meets Class II reinforced/double insulation power supply. 5 - ENVIRONMENTAL CONDITIONS Units Minimum Operating Case Temperature (Tc) C -30 Maximum Case Temperature (Tc) C Storage Temperature Humidity Cooling C % Acoustic Noise Mechanical Shock Protection Vibration Protection MTBF Lifetime Warranty SaveEnergy@erp-power.com Typical Maximum +70 +90 -40 5 Convection cooled +85 95 dBA 22 Notes Case temperature measured at the hot spot tc (see label in page 11) Case temperature measured at the hot spot tc (see label in page 11) Non-condensing Measured at a distance of 1 foot (30 cm), without and with approved dimmers per EN60068-2-27 per EN60068-2-6 & EN60068-2-64 > 300,000 hours when operated at nominal input and output conditions, and at Tc 70C At Tc 70C maximum case hot spot temperature (see hot spot tc on label in page 14) hours 50,000 Other models in the ESSV series have a longer lifetime. See details in section 8. 5 years at Tc 70C 4 www.erp-power.com ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 6 - EMC COMPLIANCE AND SAFETY APPROVALS Conducted and Radiated EMI Harmonic Current Emissions Voltage Fluctuations & Flicker ESD (Electrostatic Discharge) RF Electromagnetic Field Susceptibility Electrical Fast Transient Immunity Compliance Surge Conducted RF Disturbances Voltage Dips UL cUL EMC Compliance FCC CFR Title 47 Part 15 Class B at 120 Vac and Class A at 277 Vac IEC61000-3-2 IEC61000-3-3 For Class C equipment IEC61000-4-2 6 kV contact discharge, 8 kV air discharge, level 3 IEC61000-4-3 3 V/m, 80 - 1000 MHz, 80% modulated at a distance of 3 meters IEC61000-4-4 2 kV on AC power port for 1 minute, 1 kV on signal/control lines 1 kV line to line (differential mode) / 2 kV line to common mode ground IEC61000-4-5 (tested to secondary ground) on AC power port, 0.5 kV for outdoor cables ANSI/IEEE c62.41.1-2002 & c62.41.2-2002 category A, 2.5 kV ring wave IEC61000-4-6 3V, 0.15-80 MHz, 80% modulated IEC61000-4-11 >95% dip, 0.5 period; 30% dip, 25 periods; 95% reduction, 250 periods Safety Agency Approvals UL8750 listed Class 2, Class P CAN/CSA C22.2 No. 250.13-14 LED equipment for lighting applications Hi Pot (High Potential) or Dielectric voltage-withstand Units Minimum Vdc 4242 Safety Typical Maximum Notes Insulation between the input (AC line and Neutral) and the output Tested at the RMS voltage equivalent of 3000 Vac 7 - PROTECTION FEATURES Under-Voltage (Brownout) The ESSV series provides protection circuitry such that an application of an input voltage below the minimum stated in paragraph 1 (Input Specification) shall not cause damage to the driver. Short Circuit The ESSV series is protected against short-circuit such that a short from any output to return shall not result in a fire hazard or shock hazard. The driver shall hiccup as a result of a short circuit or over current fault. Removal of the fault will return the driver to within normal operation. The driver shall recover, with no damage, from a short across the output for an indefinite period of time. Internal Over temperature Protection The ESSV series incorporates circuitry that prevents internal damage due to an over temperature condition. An over temperature condition may be a result of an excessive ambient temperature or as a result of an internal failure. When the over temperature condition is removed, the driver shall automatically recover. Output Open Load When the LED load is removed, the output voltage of the ESSV series is typically limited to 1.3 times the maximum output voltage of each model. SaveEnergy@erp-power.com 5 www.erp-power.com ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 8 - PREDICTED LIFETIME VERSUS CASE AND AMBIENT TEMPERATURE Lifetime is defined by the measurement of the temperatures of all the electrolytic capacitors whose failure would affect light output under the nominal LED load and worst case AC line voltage. The graph in figure 1 is determined by the electrolytic capacitor with the shortest lifetime, among all electrolytic capacitors. It represents a worst case scenario in which the LED driver is powered 24 hours/day, 7 days/week. The lifetime of an electrolytic capacitor is measured when any of the following changes in performance are observed: 1) Capacitance changes more than 20% of initial value 2) Dissipation Factor (tan ): 150% or less of initial specified value 3) Equivalent Series Resistance (ESR): 150% or less of 4) Leakage current: less of initial specified value initial specified value ESSV040W-0900-42 (37.8 W, 900 mA @ 42 V max) Predicted Lifetime versus Temperature Lifetime (Hours) 120,000 100,000 96,500 80,000 68,000 60,000 48,000 40,000 34,000 24,000 20,000 0 Tcase (C) 70 Tambient (C) 41 75 46 80 51 85 56 90 61 Figure 1 Notes: * The ambient temperature Tambient and the differential between Tambient and Tcase mentioned in the above graphs are relevant only as long as both the driver and the light fixture are exposed to the same ambient room temperature. If the LED driver is housed in an enclosure or covered by insulation material, then the ambient room temperature is no longer valid. In this situation, please refer only to the case temperature Tcase. * It should be noted the graph "Lifetime vs. Ambient Temperature" may have an error induced in the final application if the mounting has restricted convection flow around the case. For applications where this is evident, the actual case temperature measured at the Tc point in the application should be used for reliability calculations. SaveEnergy@erp-power.com 6 www.erp-power.com ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 9 - PHASE-CUT DIMMING Percent of Output Current (Normalized to Rated Current Dimming of the driver is possible with standard TRIAC-based incandescent dimmers that chop the AC voltage as shown in Figure 2, or with ELV dimmers. During the rapid rise time of the AC voltage when the dimmer turns on, the driver does not generate any voltage or current oscillations, and inrush current is controlled. During the on-time of the AC input, the driver regulates the output current based upon the conduction angle. The RMS value of the driver output current is proportional to the on-time of the AC input voltage. When operating with an incandescent dimmer, the RMS output current varies depending upon the conduction angle and RMS value of the applied AC input voltage. Figure 3 shows the typical output current versus conduction angle at nominal input voltage. The ESSV series offers tri-mode dimming compatibility with both phase-cut (reverse-phase and forward-phase) and 0-10V dimmers. Phase-cut dimming always has priority over 0-10 V dimming. Please note that the ESSV series is compatible with TRIAC and ELV dimmers only at 120 Vac. When using low power ESSV models (specifically < 10 W) with a reverse-phase or forward-phase dimmer, always make sure the minimum required load is applied to the dimmer. Check the dimmer documentation for minimum load requirements. Chopped AC Input to Driver AC Wall Power Figure 1 2 Figure Output Current versus Conduction Angle 120.00% 100.00% 80.00% 60.00% 40.00% 20.00% 0.00% 0 50 100 150 Conduction Angle 200 Figure 3 10 - COMPATIBLE PHASE-CUT DIMMERS & DIMMING RANGE 120Vac Dimmers Mfg. Model Mfg. Model Mfg. Model Lutron S-603PG Lutron DVELV-303P Lutron CT-103P Leviton IPI06-1LZ Lutron SELV-300P Cooper SLC03P Leviton 6631-2 Leviton 6683-IW Leviton IPE04 Lutron DVCL-153P Leviton 6161 Lutron MAELV-600 Lutron DV-600P Leviton 6633-P Lutron FAELV-500 Lutron TGCL-153P Lutron TG-600P Lightolier ZP260QEW Lutron S-600P Cooper DLC03P Cooper DAL06P Leviton VPE06 Lutron LG-600P Dimming compatibility charts are available for each model in the ESSV series. Please contact your sales representative or send an email to: SaveEnergy@erp-power.com. SaveEnergy@erp-power.com 7 www.erp-power.com ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 ESSV Series 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 11 - 0-10 V DIMMING The ESSV drivers operate only with 0-10V dimmers that sink current. They are not designed to operate with 0-10V control systems that source current, as used in theatrical/entertainment systems. Developed in the 1980's, the 0-10V sinking current control method is adopted by the International Electrotechnical Commission (IEC) as apart of their IEC Standard 60929 Annex E. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim Signal pins respond to a 0 to 10 V signal, delivering 1% to 100% of the output current based on rated current for each model. A pull-up resistor is included internal to the driver. When the +Dim wire (purple) is short circuited to the -Dim wire (grey) or to the -LED wire (black), a small amount of current may be present on the output and, in that condition, shimmering may be observed. If the +Dim input is 1 V and 0.6 V, the output current is still present, as shown in figure 4. Please note that short circuiting the +Dim wire (purple) to the -Dim wire (grey) does not guarantee that the output current is turned off. In some models, the current may turn off when short circuiting the +Dim wire to the -Dim wire. In other models, there may be a small amount of current still present. If the +Dim input is > 10 V or open circuited, the output current is programmed to 100% of the rated current. When not used, the -Dim wire (grey) and the +Dim wire (purple) can be individually capped or cut off. In this configuration, no dimming is possible and the driver delivers 100% of its rated output current. The maximum source current (flowing from the driver to the 0-10V dimmer) supplied by the +Dim Signal pin is 1 mA. The tolerance of the output current while being dimmed shall be +/-8% typical until down to 1 V. There are two 0-10V dimming transfer functions available: a linear curve where 10V = 100% of the output current and 1V = 10% of the output current (seen in figure 4) or a non-linear curve where 10V to 8.1V=100% of Iout, 1V to 0.8V=1% of Iout, and Dim-to-off <0.8V (seen in figure 5). The linear curve is used across all the models of the ESSV series. The non-linear 0-10V dimming profile is available as an option. The non-linear curve is recommended when using standard wall-mount 0-10V logarithmic dimmers to avoid having insufficient source current available to pull the dimmer up to 10V and to account for the inability of the dimmer to pull below approximately 0.9V. In these types of installations, the modified transfer function will ensure 100% light output and dimming to 1%, regardless of the number of drivers on the 0-10V dimming line. Please contact your sales representative or send an email to SaveEnergy@erp-power.com for additional information on the non-linear curve. Normalized Output Current vs Dimming Voltage Percent of Output Current (Normalized to Rated Current Percent of Output Current (Normalized to Rated Current) Normalized Output Current vs Dimming Voltage 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 0 1 2 3 4 5 6 7 8 9 10 Dimming Voltage (V) Dimming Voltage Description Value C hysteresis > 700 mV, < 800 mV 1% 0% 0.6 A C 1.5 B Dimming Voltage (V) 8.1 9.1 10 (V) Figure 5 Figure 4 SaveEnergy@erp-power.com 100% 8 www.erp-power.com ESSV Series ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) Percent of Output Current (Normalized to Rated Current) 11 - 0-10 V DIMMING (CONTINUED) A fixed or variable resistor can be also used from the +Dim signal pin to the -Dim pin to adjust the output current.Figure 6 show the relationship of the output current to a resistor connected across the 0-10V dimming input. This is a typical graph for the entire ESSV series but is not specific to a particular model. This graph may vary from one model to the next. Normalized Output Current vs Resistance 120% 100% 80% 60% 40% 20% 0% 0 10 20 30 40 Resistance (k) 50 60 Figure 6 12 - COMPATIBLE 0-10 V DIMMERS * Lutron, Nova series (part number NFTV) * Lutron, Diva series (part number DVTV) * Leviton, IllumaTech series (part number IP710-DL) SaveEnergy@erp-power.com 9 www.erp-power.com ESSV Series ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 16 - MECHANICAL DETAILS Packaging Options: I/O Connections: Plastic case Flying leads, 18 AWG on power leads, 22 AWG on 0-10V dimming wires, 152 mm (6 in) long, 105C rated, stranded, stripped by approximately 9.5mm, and tinned. All the wires, on both input and output, have a 300 V insulation rating. Ingress Protection: IP66 rated Flammability Rating: 5VA Mounting Instructions: The ESSV driver case must be secured on a flat surface through the two mounting tabs, shown here below in the case outline drawings. 17 - OUTLINE DRAWINGS: ESSV40 SERIES Dimensions: L 84 x W 40 x H 27 mm (L 3.30 x W 1.57 x H 1.06 in) Volume: 90.7 cm3 (5.53 in3) Weight: All dimensions are in mm Figure 7 SaveEnergy@erp-power.com 10 www.erp-power.com ESSV Series ESSV010 ESSV015 ESSV020 ESSV030 ESSV040 6-10 11-15 16-20 21-30 31-40 W W W W W 6 to 40 W Constant Current LED Drivers with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 17 - LABELING The ESSV010W-0250-42 is used in figure 8 as an example to illustrate a typical label. Figure 8 USA Headquarters Tel: +1-805-517-1300 Fax: +1-805-517-1411 893 Patriot Drive, Suite E, Moorpark, CA 93021, USA CHINA Operations Tel: +86-756-6266298 Fax: +86-756-6266299 No. 8 Pingdong Road 2 Zhuhai, Guangdong, China 519060 ERP Power, LLC (ERP) reserves the right to make changes without further notice to any products herein. ERP makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ERP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in ERP data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ERP does not convey any license under its patent rights nor the rights of others. ERP products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the ERP product could create a situation where personal injury or death may occur. Should Buyer purchase or use ERP products for any such unintended or unauthorized application, Buyer shall indemnify and hold ERP and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ERP was negligent regarding the design or manufacture of the part. ERP is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. SaveEnergy@erp-power.com 11 www.erp-power.com