MC74LVXT4052 Analog Multiplexer/ Demultiplexer High-Performance Silicon-Gate CMOS The MC74LVXT4052 utilizes silicon-gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF leakage currents. This analog multiplexer/demultiplexer controls analog voltages that may vary across the complete power supply range (from VCC to VEE). The LVXT4052 is similar in pinout to the high-speed HC4052A and the metal-gate MC14052B. The Channel-Select inputs determine which one of the Analog Inputs/Outputs is to be connected, by means of an analog switch, to the Common Output/Input. When the Enable pin is HIGH, all analog switches are turned off. The Channel-Select and Enable inputs are compatible with standard TTL levels. This device has been designed so the ON resistance (RON) is more linear over input voltage than the RON of metal-gate CMOS analog switches and High-Speed CMOS analog switches. http://onsemi.com MARKING DIAGRAMS 16 SOIC-16 D SUFFIX CASE 751B 1 16 1 Select Pins Compatible with TTL Levels Fast Switching and Propagation Speeds 16 Low Crosstalk Between Switches Analog Power Supply Range (VCC - VEE) = *3.0 V to )3.0 V SOEIAJ-16 M SUFFIX CASE 966 Digital (Control) Power Supply Range (VCC - GND) = 2.5 to 6.0 V Improved Linearity and Lower ON Resistance Than Metal-Gate, HSL, or VHC Counterparts Low Noise * * Designed to Operate on a Single Supply with VEE = GND, or Using * * LVXT 4052 ALYWG G TSSOP-16 DT SUFFIX CASE 948F Features * * * * * * LVXT4052G AWLYWW Split Supplies up to 3.0 V Break-Before-Make Circuitry These Devices are Pb-Free and are RoHS Compliant LVXT4052 ALYWG 1 LVXT4052 A WL, L Y WW, W G or G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 May, 2011 - Rev. 5 1 Publication Order Number: MC74LVXT4052/D MC74LVXT4052 VCC 16 1 Y0 X2 15 X1 14 2 Y2 3 Y X 13 4 Y3 X0 12 5 Y1 X3 11 A 10 6 7 Enable VEE FUNCTION TABLE B 9 Control Inputs Enable B L L L L H L L H H X 8 GND Figure 1. Pin Connection and Marking Diagram (Top View) Select A ON Channels L H L H X Y0 Y1 Y2 Y3 X0 X1 X2 X3 NONE X = Don't Care 12 ANALOG INPUTS/OUTPUTS CHANNELSELECT INPUTS X0 14 X1 15 X2 11 X3 Y0 Y1 Y2 Y3 A B ENABLE 13 X SWITCH X COMMON OUTPUTS/INPUTS 1 5 2 3 Y SWITCH Y 4 10 9 PIN 16 = VCC PIN 7 = VEE PIN 8 = GND 6 NOTE: This device allows independent control of each switch. Channel-Select Input A controls the X-Switch, Input B controls the Y-Switch. Figure 2. Logic Diagram Double-Pole, 4-Position Plus Common Off ORDERING INFORMATION Package Shipping MC74LVXT4052DG SOIC-16 (Pb-Free) 48 Units / Rail MC74LVXT4052DR2G SOIC-16 (Pb-Free) 2500 Tape & Reel Device MC74LVXT4052DTG TSSOP-16* 96 Units / Rail MC74LVXT4052DTR2G TSSOP-16* 2500 Tape & Reel MC74LVXT4052MG SOEIAJ-16 (Pb-Free) 50 Units / Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 2 MC74LVXT4052 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Symbol Parameter VEE Negative DC Supply Voltage (Referenced to GND) VCC Positive DC Supply Voltage (Referenced to GND) (Referenced to VEE) VIS Analog Input Voltage VIN Digital Input Voltage I Value Unit *7.0 to )0.5 *0.5 to )7.0 *0.5 to )7.0 V VEE *0.5 to VCC )0.5 V *0.5 to 7.0 V (Referenced to GND) DC Current, Into or Out of Any Pin TSTG Storage Temperature Range TL Lead Temperature, 1 mm from Case for 10 Seconds V $20 mA *65 to )150 _C 260 _C TJ Junction Temperature under Bias )150 _C JA Thermal Resistance SOIC TSSOP 143 164 C/W PD Power Dissipation in Still Air, SOIC TSSOP 500 450 mW MSL Moisture Sensitivity FR Flammability Rating VESD Level 1 Oxygen Index: 30% - 35% ESD Withstand Voltage ILATCHUP Latchup Performance UL 94-V0 @ 0.125 in Human Body Model (Note 1) Machine Model (Note 2) Charged Device Model (Note 3) u2000 u200 u1000 V Above VCC and Below GND at 125C (Note 4) $300 mA Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Tested to EIA/JESD22-A114-A. 2. Tested to EIA/JESD22-A115-A. 3. Tested to JESD22-C101-A. 4. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Symbol Parameter Min Max Unit VEE Negative DC Supply Voltage (Referenced to GND) *6.0 GND V VCC Positive DC Supply Voltage (Referenced to GND) (Referenced to VEE) 2.5 2.5 6.0 6.0 V VEE VCC V 0 6.0 V *55 125 _C 0 0 100 20 ns/V VIS Analog Input Voltage VIN Digital Input Voltage TA Operating Temperature Range, All Package Types tr, tf Input Rise/Fall Time (Channel Select or Enable Inputs) (Note 5) (Referenced to GND) VCC = 3.0 V $ 0.3 V VCC = 5.0 V $ 0.5 V 5. Unused inputs may not be left open. All inputs must be tied to a high-logic voltage level or a low-logic input voltage level. 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80_C 419,300 TJ = 90_C 90 TJ = 100_C 117.8 TJ = 110_C Time, Years 1,032,200 TJ = 120_C Time, Hours 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 130_C Junction Temperature C NORMALIZED FAILURE RATE DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES 1 1 10 100 1000 TIME, YEARS Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 3 MC74LVXT4052 DC CHARACTERISTICS - Digital Section (Voltages Referenced to GND) VCC V Guaranteed Limit Symbol Parameter *55 to 25C v85C v125C Unit VIH Minimum High-Level Input Voltage, Channel-Select or Enable Inputs 3.0 4.5 5.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 V VIL Maximum Low-Level Input Voltage, Channel-Select or Enable Inputs 3.0 4.5 5.5 0.5 0.8 0.8 0.5 0.8 0.8 0.5 0.8 0.8 V IIN Maximum Input Leakage Current, Channel-Select or Enable Inputs VIN = 6.0 or GND 0 V to 6.0 V $0.1 $1.0 $1.0 A ICC Maximum Quiescent Supply Current (per Package) Channel Select, Enable and VIS = VCC or GND 6.0 4.0 40 80 A Condition IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIII IIII IIIIIIIIIIIII IIIIIIIIIIIIIIIII IIIIIIIIIII IIIIII IIIIIIII IIIIIIII IIIIIII IIIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII DC ELECTRICAL CHARACTERISTICS - Analog Section VCC V VEE V Guaranteed Limit *55 to 25C v85_C v125_C Unit Maximum "ON" Resistance VIN = VIL or VIH VIS = 1/2 (VCC - VEE) |IS| = 2.0 mA (Figure 4) 3.0 4.5 3.0 0 0 *3.0 86 37 26 108 46 33 120 55 37 RON Maximum Difference in "ON" Resistance Between Any Two Channels in the Same Package VIN = VIL or VIH VIS = 1/2 (VCC - VEE) |IS| = 2.0 mA 3.0 4.5 3.0 0 0 *3.0 15 13 10 20 18 15 20 18 15 Ioff Maximum Off-Channel Leakage Current, Any One Channel Vin = VIL or VIH; VIO = VCC or GND; Switch Off (Figure 3) 5.5 +3.0 0 -3.0 0.1 0.1 0.5 0.5 1.0 1.0 A Maximum Off-Channel Leakage Current, Common Channel Vin = VIL or VIH; VIO = VCC or GND; Switch Off (Figure 4) 5.5 +3.0 0 -3.0 0.2 0.2 2.0 2.0 4.0 4.0 Maximum On-Channel Leakage Current, Channel-to-Channel Vin = VIL or VIH; Switch-to-Switch = VCC or GND; (Figure 5) 5.5 +3.0 0 -3.0 0.2 0.2 2.0 2.0 4.0 4.0 Symbol RON Ion Parameter Test Conditions A IIII IIIIIIIII IIIIIIII III III IIIIIIIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII II III IIII IIII IIIIIIIII IIIIIIII III III II IIIII III IIII III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC CHARACTERISTICS (Input tr = tf = 3 ns) Guaranteed Limit Symbol tBBM Parameter Minimum Break-Before-Make Time Test Conditions VCC V VEE V 3.0 4.5 3.0 0.0 0.0 *3.0 VIN = VIL or VIH VIS = VCC RL = 300 CL = 35 pF (Figures 12 and 13) *Typical Characteristics are at 25_C. http://onsemi.com 4 *55 to 25_C Min Typ* v85_C v125_C Unit 1.0 1.0 1.0 6.5 5.0 3.5 - - - - - - ns MC74LVXT4052 AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 3 ns) Guaranteed Limit Symbol Parameter VCC V VEE V *55 to 25C Min Typ Max v85C Min Max v125C Min Max Unit tPLH, tPHL Maximum Propagation Delay, Channel-Select to Analog Output (Figures 16 and 17) 2.5 3.0 4.5 3.0 0 0 0 *3.0 40 28 23 23 45 30 25 25 50 35 30 28 ns tPLZ, tPHZ Maximum Propagation Delay, Enable to Analog Output (Figures 14 and 15) 2.5 3.0 4.5 3.0 0 0 0 *3.0 40 28 23 23 45 30 25 25 50 35 30 28 ns tPZL, tPZH Maximum Propagation Delay, Enable to Analog Output (Figures 14 and 15) 2.5 3.0 4.5 3.0 0 0 0 *3.0 40 28 23 23 45 30 25 25 50 35 30 28 ns Typical @ 25C, VCC = 5.0 V, VEE = 0V CPD Power Dissipation Capacitance (Figure 18) (Note 6) 45 pF CIN Maximum Input Capacitance, Channel-Select or Enable Inputs 10 pF CI/O Maximum Capacitance (All Switches Off) 10 10 1.0 pF Analog I/O Common O/I Feedthrough 6. Used to determine the no-load dynamic power consumption: P D = CPD VCC 2 f + ICC VCC . ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V) Symbol Parameter Condition Typ VCC V VEE V 25C Unit BW Maximum On-Channel Bandwidth or Minimum Frequency Response VIS = 1/2 (VCC - VEE) Ref and Test Attn = 10 dB Source Amplitude = 0 dB (Figure 7) 3.0 4.5 6.0 3.0 0.0 0.0 0.0 *3.0 80 80 80 80 MHz VISO Off-Channel Feedthrough Isolation f = 1 MHz; VIS = 1/2 (VCC - VEE) Adjust Network Analyzer output to 10 dBm on each output from the power splitter. (Figures 8 and 9) 3.0 4.5 6.0 3.0 0.0 0.0 0.0 *3.0 *70 *70 *70 *70 dB VONL Maximum Feedthrough On Loss VIS = 1/2 (VCC - VEE) Adjust Network Analyzer output to 10 dBm on each output from the power splitter. (Figure 11) 3.0 4.5 6.0 3.0 0.0 0.0 0.0 *3.0 *2 *2 *2 *2 dB Charge Injection VIN = VCC to VEE, fIS = 1 kHz, tr = tf = 3 ns RIS = 0 , CL= 1000 pF, Q = CL * VOUT (Figure 10) 5.0 3.0 *3.0 0.0 9.0 12 pC Total Harmonic Distortion THD + Noise fIS = 1 MHz, RL = 10 K, CL = 50 pF, VIS = 5.0 VPP sine wave VIS = 6.0 VPP sine wave (Figure 19) 6.0 3.0 0.0 *3.0 0.10 0.05 Q THD http://onsemi.com 5 % MC74LVXT4052 PLOTTER PROGRAMMABLE POWER SUPPLY * MINI COMPUTER DC ANALYZER ) VCC DEVICE UNDER TEST ANALOG IN COMMON OUT GND GND Figure 4. On Resistance, Test Set-Up VCC VCC 16 VEE VCC A VCC OFF ON VEE OFF NC 16 A A VCC COMMON O/I OFF VEE VEE 6 7 8 Figure 5. Maximum Off Channel Leakage Current, Any One Channel, Test Set-Up HP4195A Network Anl S1 R1 T1 6 7 8 Figure 6. Maximum On Channel Leakage Current, Channel to Channel, Test Set-Up 0.1 F VIS HP11667B Pwr Splitter VCC 100 K 0.1 F ON All untested Analog I/O pins OFF 50 K VEE 6 7 8 N/C COMMON O/I ANALOG I/O VIL VIH VCC 9 - 11 Channel Selects connected to address pins on HP4195A and appropriately configured to test each switch. Figure 7. Maximum On Channel Bandwidth, Test Set-Up http://onsemi.com 6 MC74LVXT4052 HP4195A Network Anl S1 R1 T1 0.1 F HP11667B Pwr Splitter 0.1 F VIS VCC 100 K 16 OFF All untested Analog I/O pins ON 50 K VEE 6 7 8 Channel Selects connected to address pins on HP4195A and appropriately configured to test each switch. 9 - 11 Config = Network Format = T/R (dB) CAL = Trans Cal VISO(dB) = 20 log (VT1/VR1) Display = Rectan X*A)B Scale Ref = Auto Scale View = Off, Off, Off Trig = Cont Mode Source Amplitude = )13 dB Reference Attenuation = 20 dB Test Attenuation = 0 dB Figure 8. Maximum Off Channel Feedthrough Isolation, Test Set-Up HP4195A Network Anl S1 R1 T1 HP11667B Pwr Splitter 0.1 F VIS VCC 100 K 0.1 F OFF 16 ON 50 K All untested Analog I/O pins 50 VEE 6 7 8 Config = Network Format = T/R (dB) CAL = Trans Cal Display = Rectan X*A)B Scale Ref = Auto Scale View = Off, Off, Off Trig = Cont Mode Source Amplitude = )13 dB Reference Attenuation = 20 dB Test Attenuation = 0 dB 9 - 11 Channel Selects connected to address pins on HP4195A and appropriately configured to test each switch. VISOC(dB) = 20 log (VT1/VR1) Figure 9. Maximum Common-Channel Feedthrough Isolation, Test Set-Up http://onsemi.com 7 MC74LVXT4052 VCC 16 ON/OFF VOUT OFF/ON VIN Enable VEE 6 RIS 7 8 CL * Bias Channel Selects to test each combination of analog inputs to common analog output. 9 - 11 *Includes all probe and jig capacitance. VIH VIS VIL Q = CL * VOUT VOUT VOUT Figure 10. Charge Injection, Test Set-Up HP4195A Network Anl S1 R1 T1 0.1 F HP11667B Pwr Splitter 0.1 F VIS VCC 100 K 16 ON All untested Analog I/O pins OFF 50 VEE 6 7 8 Config = Network Format = T/R (dB) CAL = Trans Cal Display = Rectan X*A)B Scale Ref = Auto Scale View = Off, Off, Off Trig = Cont Mode Source Amplitude = )13 dB Reference Attenuation = 20 dB Test Attenuation = 20 dB 9 - 11 Channel Selects connected to address pins on HP4195A and appropriately configured to test each switch. VONL(dB) = 20 log (VT1/VR1) Figure 11. Maximum On Channel Feedthrough On Loss, Test Set-Up http://onsemi.com 8 MC74LVXT4052 Tek 11801B DSO COM INPUT VCC VCC VIN 16 VOH 80% OFF ON VEE 80% of VOH CL RL Channel Selects connected to VIN and appropriately configured to test each switch. 6 7 8 9 - 11 GND tBBM VIN 50 Figure 12. Break-Before-Make, Test Set-Up Figure 13. Break-Before-Make Time VCC VCC 16 VCC CHANNEL SELECT ANALOG I/O 50% COMMON O/I TEST POINT ON/OFF OFF/ON GND tPLH ANALOG OUT CL * 6 7 8 tPHL 50% CHANNEL SELECT *Includes all probe and jig capacitance. Figure 14. Propagation Delays, Channel Select to Analog Out tf GND POSITION 1 WHEN TESTING tPHZ AND tPZH 1 POSITION 2 WHEN TESTING tPLZ AND tPZL tr 90% 50% 10% ENABLE tPZL ANALOG OUT tPLZ 50% VCC 2 GND HIGH IMPEDANCE 10% tPHZ tPZH ANALOG OUT Figure 15. Propagation Delay, Test Set-Up Channel Select to Analog Out 90% VCC VCC 16 1 ANALOG I/O ON/OFF 2 VOL 1 K TEST POINT CL * ENABLE VOH 50% HIGH IMPEDANCE Figure 16. Propagation Delays, Enable to Analog Out 6 7 8 Figure 17. Propagation Delay, Test Set-Up Enable to Analog Out http://onsemi.com 9 MC74LVXT4052 VCC A VCC ON/OFF NC OFF/ON VIL 15 10 - 11, 13 - 14 12 Channel Select Figure 18. Power Dissipation Capacitance, Test Set-Up HP3466 DMM )V COM HP3466 DMM )V COM HP E3630A DC Pwr Supply COM )20 V HP 339 Distortion Measurement Set *20 V Analyzer Input COM Oscillator Output COM 16 ON RL OFF 50 K 6 7 8 9 - 11 CL Channel Selects connected to DC bias supply or ground and appropriately configured to test each switch. Figure 19. Total Harmonic Distortion, Test Set-Up http://onsemi.com 10 MC74LVXT4052 APPLICATIONS INFORMATION outputs to VCC or GND through a low value resistor helps minimize crosstalk and feedthrough noise that may be picked up by an unused switch. Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that: VEE - GND = 0 to *6 volts VCC - GND = 2.5 to 6 volts VCC - VEE = 2.5 to 6 volts and VEE v GND When voltage transients above VCC and/or below VEE are anticipated on the analog channels, external Germanium or Schottky diodes (Dx) are recommended as shown in Figure 22. These diodes should be able to absorb the maximum anticipated current surges during clipping. The Channel Select and Enable control pins should be at VCC or GND logic levels. VCC being recognized as a logic high and GND being recognized as a logic low. In this example: VCC = )5 V = logic high GND = 0 V = logic low The maximum analog voltage swing is determined by the supply voltages VCC and VEE. The positive peak analog voltage should not exceed VCC. Similarly, the negative peak analog voltage should not go below VEE. In this example, the difference between VCC and VEE is five volts. Therefore, using the configuration of Figure 21, a maximum analog signal of five volts peak-to-peak can be controlled. Unused analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and +3.0 V +3.0 V -3.0 V 16 ANALOG SIGNAL -3.0 V ON 6 7 8 11 10 9 +3.0 V ANALOG SIGNAL +5 V +5 V -3.0 V 16 ANALOG SIGNAL GND TO EXTERNAL CMOS CIRCUITRY 0 to 3.0 V DIGITAL SIGNALS ON 6 7 8 Figure 20. Application Example 11 10 9 ANALOG SIGNAL VCC Dx 16 VCC Dx ON/OFF Dx Dx VEE VEE VEE 7 8 Figure 22. External Germanium or Schottky Clipping Diodes http://onsemi.com 11 GND TO EXTERNAL CMOS CIRCUITRY 0 to 5 V DIGITAL SIGNALS Figure 21. Application Example VCC +5 V MC74LVXT4052 A 10 12 LEVEL SHIFTER 14 B 9 15 LEVEL SHIFTER 11 13 ENABLE 6 1 LEVEL SHIFTER 5 2 4 3 Figure 23. Function Diagram, LVXT4052 http://onsemi.com 12 X0 X1 X2 X3 X Y0 Y1 Y2 Y3 Y MC74LVXT4052 PACKAGE DIMENSIONS SOIC-16 CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 B M S G R K F X 45 _ C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S SOLDERING FOOTPRINT 8X 6.40 16X 1 1.12 16 16X 0.58 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS http://onsemi.com 13 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 MC74LVXT4052 PACKAGE DIMENSIONS TSSOP-16 CASE 948F-01 ISSUE B 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U S V S K S EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. N 8 1 0.25 (0.010) M 0.15 (0.006) T U S A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS http://onsemi.com 14 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74LVXT4052 PACKAGE DIMENSIONS SOEIAJ-16 CASE 966-01 ISSUE A 16 LE 9 Q1 E HE 1 M_ L 8 Z DETAIL P D e VIEW P A DIM A A1 b c D E e HE L LE M Q1 Z A1 b 0.13 (0.005) c M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). 0.10 (0.004) MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.031 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 15 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74LVXT4052/D