Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP) X7R Dielectric, 6.3 - 250 VDC (Commercial & Automotive Grade) Overview KEMET's Flexible Termination (FT-CAP) multilayer ceramic capacitor in X7R dielectric incorporates a unique, flexible termination system that is integrated with KEMET's standard termination materials. A conductive silver epoxy is utilized between the base metal and nickel barrier layers of KEMET's standard termination system in order to establish pliability while maintaining terminal strength, solderability and electrical performance. This technology was developed in order to address the primary failure mode of MLCCs- flex cracks, which are typically the result of excessive tensile and shear stresses produced during board flexure and thermal cycling. Flexible termination technology inhibits the transfer of board stress to the rigid ceramic body, therefore mitigating flex cracks which can result in low IR or short circuit failures. Although this technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination systems.FT-CAP complements KEMET's Open Mode, Floating Electrode (FE-CAP), Floating Electrode with Flexible Termination (FF-CAP) and KEMET Power Solutions (KPS) product lines by providing a complete portfolio of flex mitigation solutions. Combined with the stability of an X7R dielectric and designed to accommodate all capacitance requirements, these flex-robust devices are RoHS-compliant, offer up to 5mm of flex-bend capability and exhibit a predictable change in capacitance with respect to time and voltage. Capacitance change with reference to ambient temperature is limited to 15% from -55C to +125C. In addition to commercial grade, automotive grade devices are available which meet the demanding Automotive Electronics Council's AEC-Q200 qualification requirements. Ordering Information C Ceramic 1206 X Case Size Specification/ (L" x W") Series 0603 0805 1206 1210 1808 1812 1825 2220 2225 X = Flexible Termination 106 K 4 R A C AUTO Capacitance Code (pF) Capacitance Tolerance Voltage Dielectric Failure Rate/ Design Termination Finish1 Packaging/Grade (C-Spec)2 2 significant digits + number of zeros J = 5% K = 10% M = 20% 9 = 6.3 V 8 = 10 V 4 = 16 V 3 = 25 V 5 = 50 V 1 = 100 V 2 = 200 V A = 250 V R = X7R A = N/A C = 100% Matte Sn L = SnPb (5% minimum) Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked AUTO = Automotive Grade 7" Reel Unmarked Additional termination finish options may be available. Contact KEMET for details. SnPb termination finish option is not available on Automotive Grade product. 2 Additional reeling or packaging options may be available. Contact KEMET for details. 1 1,2 One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Dimensions - Millimeters (Inches) L W B T S Metric Size Code L Length W Width 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 1.60 (.064) 0.17 (.007) 2.00 (.079) 0.20 (.008) 3.30 (.130) 0.40 (.016) 3.30 (.130) 0.40 (.016) 4.70 (.185) 0.50 (.020) 4.50 (.178) 0.40 (.016) 4.60 (.181) 0.40 (.016) 5.90 (.232) 0.75 (.030) 5.90 (.232) 0.75 (.030) 0.80 (.032) 0.15 (.006) 1.25 (.049) 0.20 (.008) 1.60 (.063) 0.20 (.008) 2.50 (.098) 0.20 (.008) 2.00 (.079) 0.20 (.008) 3.20 (.126) 0.30 (.012) 6.40 (.252) 0.40 (.016) 5.00 (.197) 0.40 (.016) 6.40 (.248) 0.40 (.016) T Thickness 0.45 (.018) 0.15 (.006) 0.50 (0.02) 0.25 (.010) 0.60 (.024) 0.25 (.010) 0.60 (.024) 0.25 (.010) See Table 2 for 0.70 (.028) 0.35 (.014) Thickness 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) Benefits * * * * * -55C to +125C operating temperature range Superior flex performance (up to 5 mm) High capacitance flex mitigation Pb-Free and RoHS Compliant EIA 0603, 0805, 1206, 1210, 1808, 1812, 1825, 2220, and 2225 case sizes * DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V, 200 V, and 250 V S Separation Minimum B Bandwidth Mounting Technique 0.58 (.023) 0.75 (.030) Solder Wave or Solder Reflow N/A Solder Reflow Only Ceramic Surface Mount EIA Size Code * * * * Capacitance offerings ranging from 180 pF to 22 F Available capacitance tolerances of 5%, 10%, and 20% Non-polar device, minimizing installation concerns 100% pure matte tin-plated termination finish allowing for excellent solderability * SnPb termination finish option available upon request (5% min) * Commercial and Automotive (AEC-Q200) grades available Applications Typical applications include circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Examples include raw power input side filtering (power plane/bus), high current applications (automobile battery line) and circuits that cannot be fused to open. Markets include consumer, medical, industrial (power supply), automotive, aerospace and telecom. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance & Reliability. Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC-Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC-Q200, please visit their website at www.aecouncil.com. Environmental Compliance Pb-Free and RoHS Compliant (excluding SnPb termination finish option). Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range -55C to +125C Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) 15% Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0% Dielectric Withstanding Voltage (DWV) Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C 250% of rated voltage (5 1 seconds and charge/discharge not exceeding 50 mA) 5% (6.3 and 10 V), 3.5% (16 and 25 V) and 2.5% (50 to 250 V) See Insulation Resistance Limit Table (Rated voltage applied for 120 5 seconds @ 25C) Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and dissipation factor (DF) measured under the following conditions: 1 kHz 50 Hz and 1.0 0.2 Vrms if capacitance 10 F 120 Hz 10 Hz and 0.5 0.1 Vrms if capacitance > 10 F Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Rated DC Voltage Dielectric Capacitance Value Dissipation Factor (Maximum %) > 25 X7R 16/25 Capacitance Shift Insulation Resistance 20% 10% of Initial Limit 3.0 All 5.0 < 16 7.5 Insulation Resistance Limit Table (X7R Dielectric) EIA Case Size 1,000 Megohm Microfarads or 100 G 500 Megohm Microfarads or 10 G 0201 N/A ALL 0402 < 0.012 F 0.012 F 0603 < 0.047 F 0.047 F 0805 < 0.047 F 0.047 F 1206 < 0.22 F 0.22 F 1210 < 0.39 F 0.39 F 1808 ALL N/A 1812 < 2.2 F 2.2 F 1825 ALL N/A 2220 < 10 F 10 F 2225 ALL N/A (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 1A - Capacitance Range/Selection Waterfall (0603 - 1210 Case Sizes) 2 A Voltage DC 100 200 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 200 250 6.3 10 16 25 50 100 CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CD CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CD CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DG DG DD DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DG DG DD DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DG DG DD DD DD DD DD DE DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DC DC DC DC DD DG DG DD DG DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DD DD DG DG DD DD DE DE DH DH DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DD DD DD DD DD DD DE DE DE DE DE DG DG DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DE DE DE DG DG DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC DC Voltage DC Voltage Code 9 8 4 3 5 1 2 9 8 4 3 5 1 2 Series FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FG FH FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FG FH FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FE FF FG FC FF FG FH FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FH FH FH FJ FG FM FG FG FH FM FK FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FC FD FD FD FD FD FF FH FG FG FG FG FH FM FK FS FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FD FD FD FD FD FD FD FD FD FF FG FL FM FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FF FG FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FB FC FC FC FF FG A 9 8 4 3 5 1 2 A Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions C0603X C0805X EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF ED ED EN ED EF EF EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF ED ED EN ED EF EF EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EF ED EF ED ED EN ED EF EF EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EB EB EB EC ED EE EF EG EG EG EF EF EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EC EC EC EC EC EC EC ED ED ED EH EH EH EH EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EC EC EB EB EB EB EC EC EC EC EM EG EG EG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB ED ED ED ED EM EG EG EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB EB ED ED ED ED EM 16 25 50 100 200 EB EB EB EB EB 10 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 6.3 K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 250 Cap Code J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 250 1 200 5 250 3 200 4 50 8 100 9 25 A 16 2 10 1 6.3 5 250 3 100 4 200 8 25 9 50 A 16 2 10 1 6.3 5 100 3 200 4 25 8 50 9 16 2 10 1 16 5 10 Cap C1210X 3 6.3 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 685 825 C1206X 4 Cap Tolerance 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1,000 pF 1,200 pF 1,500 pF 1,800 pF 2,200 pF 2,700 pF 3,300 pF 3,900 pF 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 F 0.12 F 0.15 F 0.18 F 0.22 F 0.27 F 0.33 F 0.39 F 0.47 F 0.56 F 0.68 F 0.82 F 1.0 F 1.2 F 1.5 F 1.8 F 2.2 F 2.7 F 3.3 F 3.9 F 4.7 F 5.6 F 6.8 F 8.2 F C0805X 8 25 C0603X 9 50 Series Voltage Code 6.3 Cap Cap Code A 9 8 4 3 5 1 2 C1206X (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1210X C1013_X7R_FT-CAP_SMD * 10/3/2012 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 1A - Capacitance Range/Selection Waterfall (0603 - 1210 Case Sizes) cont'd 2 A 250 1 200 5 250 3 200 4 5 1 2 A 50 8 100 9 50 A 16 2 25 1 10 5 6.3 16 3 250 4 200 8 100 9 25 A C1210X 50 2 10 16 1 6.3 10 5 250 6.3 3 100 4 200 8 25 9 50 2 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions M M M M M EH EH EH FH FH FH FS 16 3 5 1 2 A 9 8 4 C1206X 25 10 4 6.3 8 250 9 200 A 100 2 25 1 C0805X 50 5 16 3 10 4 6.3 8 250 9 100 2 200 1 25 5 C0603X 50 16 3 10 4 6.3 8 200 9 Series 50 25 Voltage Code 100 16 FS FS Voltage DC 10 Cap Code K K K K K 6.3 Cap J J J J J 1 C1206X 100 Cap Tolerance 5 200 3 50 4 C0805X 100 8 16 106 126 156 186 226 9 Voltage DC 25 10 F 12 F 15 F 18 F 22 F Voltage Code 10 Cap Code C0603X 6.3 Cap Series 3 C1210X Table 1B - Capacitance Range/Selection Waterfall (1808 - 2225 Case Sizes) 1 2 A 5 1 2 A 3 5 1 2 A 5 1 2 A 200 250 25 50 100 200 250 50 100 200 250 25 50 100 200 250 50 100 200 250 Voltage Code 5 1 2 Series Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions C1808X GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GG GG GG GG GG GJ 50 100 200 A 3 5 1 2 C1812X JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JD JF JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JC JD JF JC JC JC JC JC JC JC JC JC JC JC JD JF JF JC JC JC JC JC JC JC JC JC JC JD JD JF JF JC JC JC JC JC JC JC JC JC JC JD JD JF JF 100 200 250 2 A 3 5 1 2 A 5 1 2 A C1825X (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE 50 1 KC KC KC KC KC KC KC KC KC KC KC KC KD KD KD KE KE KE 250 5 KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KC KD KE 200 A KC KC KC KC KC KC KC KC KC KB KB KB KB KB KB KB KB KB KC KD KD 100 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 50 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HD HD HF HF 25 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HD HD HF HF 250 HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HB HC HD HF 200 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GE GF GG GG GG GG GJ 100 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GG GG GG GG GG GG GG GG 50 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE 250 GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GB GC GC GE GE 25 LD LD LD LD LD LD LD LD 250 M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M C2225X 5 Voltage DC K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K C2220X 3 LD LD LD LD LD LD LD LD LD LD LD LD LD LD J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J C1825X A LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD LD Cap Tolerance C1812X 2 200 Cap Cap Code 1 100 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 5 Voltage DC 100 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 F 0.12 F 0.15 F 0.18 F 0.22 F 0.27 F 0.33 F 0.39 F 0.47 F 0.56 F 0.68 F 0.82 F 1.0 F 1.2 F 1.5 F 1.8 F 2.2 F Voltage Code 50 Cap Code C1808X 50 Cap Series C2220X C2225X C1013_X7R_FT-CAP_SMD * 10/3/2012 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 1B - Capacitance Range/Selection Waterfall (1808 - 2225 Case Sizes) cont'd 5 50 100 200 250 50 100 200 250 25 50 1 C2225X 2 A 5 1 2 A 250 3 200 A 100 2 50 1 250 5 200 A 100 2 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions M M M M M M M M M M M M GK GK GK JF JO JO 25 50 100 200 250 50 100 200 250 25 50 100 200 250 50 100 200 250 JO Voltage DC 250 K K K K K K K K K K K K 1 200 Cap Code J J J J J J J J J J J J 5 100 Cap 275 335 395 475 565 685 825 106 126 156 186 226 C2220X 3 50 2.7 F 3.3 F 3.9 F 4.7 F 5.6 F 6.8 F 8.2 F 10 F 12 F 15 F 18 F 22 F C1825X A 25 Voltage DC Cap Tolerance C1812X 2 250 1 200 C1808X 5 100 Series Voltage Code 50 Cap Cap Code Voltage Code 5 1 2 A 3 5 1 2 A 5 1 2 A 3 5 1 2 A 5 1 2 A Series C1808X C1812X C1825X C2220X C2225X Table 2 - Chip Thickness/Packaging Quantities Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel CB CD DC DD DE DG DH EB EC EN ED EE EF EM EG EH FB FC FD FE FF FG FL 0603 0603 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 0.80 0.07 0.80 0.15 0.78 0.10 0.90 0.10 1.00 0.10 1.25 0.15 1.25 0.20 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.20 0.15 1.25 0.15 1.60 0.15 1.60 0.20 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.40 0.15 4,000 4,000 0 0 0 0 0 4,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10,000 10,000 0 0 0 0 0 10,000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4,000 4,000 2,500 2,500 2,500 4,000 4,000 4,000 2,500 2,500 2,500 2,500 2,000 2,000 4,000 4,000 4,000 2,500 2,500 2,500 2,000 0 0 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity Plastic Quantity Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1013_X7R_FT-CAP_SMD * 10/3/2012 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 2 - Chip Thickness/Packaging Quantities cont'd Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel FH FM FJ FK FS LD GB GC GE GF GG GK GJ HB HC HD HF JC JD JF JO KB KC KD KE 1210 1210 1210 1210 1210 1808 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 2220 2220 2220 2220 2225 2225 2225 2225 1.55 0.15 1.70 0.20 1.85 0.20 2.10 0.20 2.50 0.20 0.90 0.10 1.00 0.10 1.10 0.10 1.30 0.10 1.50 0.10 1.55 0.10 1.60 0.20 1.70 0.15 1.10 0.15 1.15 0.15 1.30 0.15 1.50 0.15 1.10 0.15 1.30 0.15 1.50 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2,000 2,000 2,000 2,000 1,000 2,500 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 1,000 1,000 1,000 1,000 8,000 8,000 8,000 8,000 4,000 10,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 4,000 4,000 4,000 4,000 Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity Plastic Quantity Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 3 - Chip Capacitor Land Pattern Design Recommendations per IPC-7351 EIA Size Code Metric Size Code 0603 Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 1608 0.85 1.25 1.10 4.00 2.10 0.75 1.05 1.00 3.10 1.50 0.65 0.85 0.90 2.40 1.20 0805 2012 1.00 1.35 1.55 4.40 2.60 0.90 1.15 1.45 3.50 2.00 0.80 0.95 1.35 2.80 1.70 1206 3216 1.60 1.65 1.90 5.90 2.90 1.50 1.45 1.80 5.00 2.30 1.40 1.25 1.70 4.30 2.00 1210 3225 1.60 1.65 2.80 5.90 3.80 1.50 1.45 2.70 5.00 3.20 1.40 1.25 2.60 4.30 2.90 1808 4520 2.25 1.85 2.30 7.40 3.30 2.15 1.65 2.20 6.50 2.70 2.05 1.45 2.10 5.80 2.40 1812 4532 2.10 1.80 3.60 7.00 4.60 2.00 1.60 3.50 6.10 4.00 1.90 1.40 3.40 5.40 3.70 1825 4564 2.15 1.80 6.90 7.10 7.90 2.05 1.60 6.80 6.20 7.30 1.95 1.40 6.70 5.50 7.00 2220 5650 2.85 2.10 5.50 8.80 6.50 2.75 1.90 5.40 7.90 5.90 2.65 1.70 5.30 7.20 5.60 2225 5664 2.85 2.10 6.90 8.80 7.90 2.75 1.90 6.80 7.90 7.30 2.65 1.70 6.70 7.20 7.00 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC-7351). Soldering Process Recommended Soldering Technique: * Solder wave or solder reflow for EIA case sizes 0603, 0805, and 1206 * All other EIA case sizes are limited to solder reflow only Recommended Soldering Profile: * KEMET recommends following the guidelines outlined in IPC/JEDEC J-STD-020 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Table 4 - Performance & Reliability: Test Methods and Conditions Stress Reference Test or Inspection Method Terminal Strength JIS-C-6429 Appendix 1, Note: Force of 1.8 kg for 60 seconds. Board Flex JIS-C-6429 Appendix 2, Note: Standard termination system - 2.0 mm (minimum) for all except 3 mm for C0G. Flexible termination system - 3.0 mm (minimum). Magnification 50 X. Conditions: Solderability a) Method B, 4 hours @ 155C, dry heat @ 235C J-STD-002 b) Method B @ 215C category 3 c) Method D, category 3 @ 260C Temperature Cycling JESD22 Method JA-104 Biased Humidity MIL-STD-202 Method 103 Moisture Resistance MIL-STD-202 Method 106 1,000 Cycles (-55C to +125C). Measurement at 24 hours +/- 2 hours after test conclusion. Load Humidity: 1,000 hours 85C/85% RH and rated voltage. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. Low Volt Humidity: 1,000 hours 85C/85% RH and 1.5 V. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours +/- 2 hours after test conclusion. -55C/+125C. Note: Number of cycles required - 300, maximum transfer time - 20 seconds, dwell time - 15 minutes. Air - Air. Thermal Shock MIL-STD-202 Method 107 High Temperature Life MIL-STD-202 Method 108 /EIA-198 Storage Life MIL-STD-202 Method 108 150C, 0 VDC for 1,000 hours. Mechanical Shock MIL-STD-202 Method 213 Figure 1 of Method 213, Condition F. Resistance to Solvents MIL-STD-202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent. 1,000 hours at 125C (85C for X5R, Z5U and Y5V) with 2 X rated voltage applied. Storage and Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature- reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40C and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of receipt. Construction Reference A B C D Item Material Finish 100% Matte Sn SnPb (5% min) Barrier Layer Ni Termination System Epoxy Layer Ag Base Metal Cu E Inner Electrode Ni F Dielectric Material BaTiO3 Note: Image is exaggerated in order to clearly identify all components of construction. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Capacitor Marking (Optional): These surface mount multilayer ceramic capacitors are normally supplied unmarked. If required, they can be marked as an extra cost option. Marking is available on most KEMET devices but must be requested using the correct ordering code identifier(s). If this option is requested, two sides of the ceramic body will be laser marked with a "K" to identify KEMET, followed by two characters (per EIA-198 - see table below) to identify the capacitance value. EIA 0603 case size devices are limited to the "K" character only. Marking appears in legible contrast. Illustrated below is an example of an MLCC with laser marking of "KA8", which designates a KEMET device with rated capacitance of 100 F. Orientation of marking is vendor optional. _ KA8 Laser marking option is not available on: * C0G and Y5V dielectric devices * EIA 0402 case size devices * EIA 0603 case size devices with Flexible Termination option. Capacitance (pF) For Various Alpha / Numeral Identifiers Alpha Character Numeral 9 0 1 2 3 4 5 6 7 8 100,000,000 Capacitance (pF) A 0.1 10 10 100 1,000 10,000 100,000 1,000,000 10,000,000 B 0.11 1.1 11 110 1,100 11,000 110,000 1,100,000 11,000,000 110,000,000 C 0.12 12 12 120 1,200 12,000 120,000 1,200,000 12,000,000 120,000,000 D 0.13 13 13 130 1,300 13,000 130,000 1,300,000 13,000,000 130,000,000 E 0.15 15 15 150 1,500 15,000 150,000 1,500,000 15,000,000 150,000,000 160,000,000 F 0.16 16 16 160 1,600 16,000 160,000 1,600,000 16,000,000 G 0.18 18 18 180 1,800 18,000 180,000 1,800,000 18,000,000 180,000,000 H 0.2 20 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000 J 0.22 22 22 220 2,200 22,000 220,000 2,200,000 22,000,000 220,000,000 K 0.24 2.4 24 240 2,400 24,000 240,000 2,400,000 24,000,000 240,000,000 L 0.27 2.7 27 270 2,700 27,000 270,000 2,700,000 27,000,000 270,000,000 M 0.3 30 30 300 3,000 30,000 300,000 3,000,000 30,000,000 300,000,000 N 0.33 33 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000 P 0.36 36 36 360 3,600 36,000 360,000 3,600,000 36,000,000 360,000,000 Q 0.39 39 39 390 3,900 39,000 390,000 3,900,000 39,000,000 390,000,000 R 0.43 43 43 430 4,300 43,000 430,000 4,300,000 43,000,000 430,000,000 S 0.47 4.7 47 470 4,700 47,000 470,000 4,700,000 47,000,000 470,000,000 T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000 U 0.56 56 56 560 5,600 56,000 560,000 5,600,000 56,000,000 560,000,000 V 0.62 62 62 620 6,200 62,000 620,000 6,200,000 62,000,000 620,000,000 W 0.68 68 68 680 6,800 68,000 680,000 6,800,000 68,000,000 680,000,000 X 0.75 75 75 750 7,500 75,000 750,000 7,500,000 75,000,000 750,000,000 Y 0.82 82 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000 Z 0.91 9.1 91 910 9,100 91,000 910,000 9,100,000 91,000,000 910,000,000 a 0.25 25 25 250 2,500 25,000 250,000 2,500,000 25,000,000 250,000,000 b 0.35 35 35 350 3,500 35,000 350,000 3,500,000 35,000,000 350,000,000 d 0.4 40 40 400 4,000 40,000 400,000 4,000,000 40,000,000 400,000,000 e 0.45 45 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000 f 0.5 50 50 500 5,000 50,000 500,000 5,000,000 50,000,000 500,000,000 m 0.6 60 60 600 6,000 60,000 600,000 6,000,000 60,000,000 600,000,000 n 0.7 70 70 700 7,000 70,000 700,000 7,000,000 70,000,000 700,000,000 t 0.8 80 80 800 8,000 80,000 800,000 8,000,000 80,000,000 800,000,000 y 0.9 90 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar Code Label Anti-Static Reel (R) Embossed Plastic* or Punched Paper Carrier. ET KEM Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 and 2225 Military) Sprocket Holes Embossment or Punched Cavity 8 mm, 12 mm or 16 mm Carrier Tape 178 mm (7.00") or 330 mm (13.00") Anti-Static Cover Tape (.10 mm (.004") Maximum Thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 - Carrier Tape Configuration - Embossed Plastic & Punched Paper (mm) EIA Case Size Tape Size (W)* Lead Space (P1)* 01005 - 0402 8 2 0603 - 1210 8 4 1805 - 1808 12 4 1812 12 8 KPS 1210 12 8 KPS 1812 & 2220 16 12 Array 0508 & 0612 8 4 *Refer to Figures 1 & 2 for W and P1 carrier tape reference locations. *Refer to Tables 6 & 7 for tolerance specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo [10 pitches cumulative tolerance on tape 0.2 mm] Po E1 Ao F Ko W B1 E2 Bo S1 P1 T1 Center Lines of Cavity OD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 1.75 0.10 (0.069 0.004) R Reference S1 Minimum Note 2 Note 3 25.0 (0.984) 4.0 0.10 2.0 0.05 (0.079 0.600 (0.157 0.004) 0.002) (0.024) 30 (1.181) P0 P2 T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F P1 3.5 0.05 4.0 0.10 (0.138 0.002) (0.157 0.004) 8.0 0.10 (0.315 5.5 0.05 0.004) (0.217 0.002) 5.5 0.05 8.0 0.10 (0.315 (0.217 0.002) 0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 6). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Figure 2 - Punched (Paper) Carrier Tape Dimensions P2 T Po ODo [10 pitches cumulative tolerance on tape 0.2 mm] E1 A0 F P1 T1 T1 Top Cover Tape W E2 B0 Bottom Cover Tape G Cavity Size, See Note 1, Table 7 Center Lines of Cavity Bottom Cover Tape User Direction of Unreeling Table 7 - Punched (Paper) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 E1 P0 P2 T1 Maximum G Minimum 8 mm 1.5 +0.10 -0.0 (0.059 +0.004 -0.0) 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) 0.10 (0.004) Maximum 0.75 (0.030) R Reference Note 2 25 (0.984) T Maximum W Maximum A0 B 0 1.1 (0.098) 8.3 (0.327) 8.3 (0.327) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Half (2 mm) 8 mm Single (4 mm) E2 Minimum 6.25 (0.246) F 3.5 0.05 (0.138 0.002) P1 2.0 0.05 (0.079 0.002) 4.0 0.10 (0.157 0.004) Note 1 1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. c) rotation of the component is limited to 20 maximum (see Figure 3). d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 6). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 3 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 - 200 Bo Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Figure 4 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape s Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 56 10 72 - 200 5 S) Figure 5 - Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com R C1013_X7R_FT-CAP_SMD * 10/3/2012 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Figure 6 - Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (O 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A N (See Note) C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 8 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Figure 7 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum 100 mm Minimum Leader 400 mm Minimum Components Top Cover Tape Figure 8 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm Bulk Cassette Packaging (Ceramic Chips Only) Meets Dimensional Requirements IEC-286 and EIAJ 7201 6 8 0.1 8 8 0.1 12.0 0.1 Unit mm *Reference 19.0* 36 00.2 31.5 0.2 0 53 3* 10* 1.5 2.0 3.0 0.1 0 0 0.1 0.2 0 5 0* 110 0.7 Capacitor Dimensions for Bulk Cassette Cassette Packaging - Millimeters EIA Size Code Metric Size Code L Length W Width B Bandwidth S Separation Minimum T Thickness Number of Pieces/Cassette 0402 1005 1.0 0.05 0.5 0.05 0.2 to 0.4 0.3 0.5 0.05 50,000 0603 1608 1.6 0.07 0.8 0.07 0.2 to 0.5 0.7 0.8 0.07 15,000 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) KEMET Corporation World Headquarters Europe Asia 2835 KEMET Way Simpsonville, SC 29681 Southern Europe Geneva, Switzerland Tel: 41-22-715-0100 Northeast Asia Paris, France Tel: 33-1-4646-1009 Shenzhen, China Tel: 86-755-2518-1306 Sasso Marconi, Italy Tel: 39-051-939111 Beijing, China Tel: 86-10-5829-1711 Milan, Italy Tel: 39-02-57518176 Shanghai, China Tel: 86-21-6447-0707 Fort Lauderdale, FL Tel: 954-766-2800 Rome, Italy Tel: 39-06-23231718 Taipei, Taiwan Tel: 886-2-27528585 North America Madrid, Spain Tel: 34-91-804-4303 Southeast Asia Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offices Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642 Central Europe Hong Kong Tel: 852-2305-1168 Singapore Tel: 65-6586-1900 Landsberg, Germany Tel: 49-8191-3350800 Penang, Malaysia Tel: 60-4-6430200 Dortmund, Germany Tel: 49-2307-3619672 Bangalore, India Tel: 91-806-53-76817 Kwidzyn, Poland Tel: 48-55-279-7025 Central Novi, MI Tel: 248-994-1030 Carmel, IN Tel: 317-706-6742 West Milpitas, CA Tel: 408-433-9950 Mexico Zapopan, Jalisco Tel: 52-33-3123-2141 Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Farjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 19 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 - 250 VDC (Commercial Grade & Automotive Grade) Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com Date: 2012.10.09 16:49:10 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1013_X7R_FT-CAP_SMD * 10/3/2012 20