LT3012B 250mA, 4V to 80V Low Dropout Micropower Linear Regulator U FEATURES DESCRIPTIO The LT(R)3012B is a high voltage, micropower low dropout linear regulator. The device is capable of supplying 250mA of output current with a dropout voltage of 400mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (40A operating) makes the LT3012B an ideal choice. Quiescent current is also well controlled in dropout. Wide Input Voltage Range: 4V to 80V Low Quiescent Current: 40A Low Dropout Voltage: 400mV Output Current: 250mA No Protection Diodes Needed Adjustable Output from 1.24V to 60V Stable with 3.3F Output Capacitor Stable with Aluminum, Tantalum or Ceramic Capacitors Reverse-Battery Protection No Reverse Current Flow from Output to Input Thermal Limiting Thermally Enhanced 16-Lead TSSOP and 12-Pin (4mm x 3mm) DFN Packages U APPLICATIO S Low Current High Voltage Regulators Regulator for Battery-Powered Systems Telecom Applications Automotive Applications Other features of the LT3012B include the ability to operate with very small output capacitors. The regulators are stable with only 3.3F on the output while most older devices require between 10F and 100F for stability. Small ceramic capacitors can be used without any need for series resistance (ESR) as is common with other regulators. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting and reverse current protection. The device is available with an adjustable output with a 1.24V reference voltage. The LT3012B regulator is available in the 16-lead TSSOP and 12 pin low profile (0.75mm) (4mm x 3mm) DFN packages with an exposed pad for enhanced thermal handling capability. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO Dropout Voltage 400 5V Supply VIN 5.4V TO 80V VOUT 5V 250mA OUT LT3012B 1F 750k 3.3F ADJ GND 249k 3012B TA01 DROPOUT VOLTAGE (mV) IN 350 300 250 200 150 100 50 0 0 50 100 150 200 OUTPUT CURRENT (mA) 250 3012B TA02 3012bf 1 LT3012B W W W AXI U U ABSOLUTE RATI GS (Note 1) IN Pin Voltage ................................................... 80V OUT Pin Voltage ............................................... 60V IN to OUT Differential Voltage ........................... 80V ADJ Pin Voltage .................................................. 7V Output Short-Circuit Duration ..................... Indefinite Storage Temperature Range TSSOP Package ........................... -65C to 150C DFN Package ............................... -65C to 125C Operating Junction Temperature Range (Notes 3, 9, 10) ........................... -40C to 125C Lead Temperature (Soldering, 10 sec)............ 300C U U W PACKAGE/ORDER I FOR ATIO TOP VIEW TOP VIEW GND 1 16 GND NC 1 12 NC NC 2 15 NC OUT 2 11 IN OUT 3 14 IN OUT 3 10 IN OUT 4 ADJ 4 9 NC ADJ 5 12 NC GND 5 8 NC GND 6 11 NC NC 6 7 NC NC 7 10 NC GND 8 9 13 DE PACKAGE 12-LEAD (4mm x 3mm) PLASTIC DFN 13 IN 17 GND FE PACKAGE 16-LEAD PLASTIC TSSOP TJMAX = 125C, JA = 40C/ W, JC = 16C/ W EXPOSED PAD (PIN 13) IS GND MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 40C/ W, JC = 16C/ W EXPOSED PAD (PIN 17) IS GND MUST BE SOLDERED TO PCB ORDER PART NUMBER DE PART MARKING ORDER PART NUMBER FE PART MARKING LT3012BEDE 3012B LT3012BEFE 3012BEFE Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25C. PARAMETER CONDITIONS MIN TYP Minimum Input Voltage ADJ Pin Voltage (Notes 2, 3) ILOAD = 250mA VIN = 4V, ILOAD = 1mA 4.5V < VIN < 80V, 1mA < ILOAD < 250mA 1.225 1.2 Line Regulation VIN = 4V to 80V, ILOAD = 1mA (Note 2) 0.1 5 mV Load Regulation (Note 2) VIN = 4.5V, ILOAD = 1mA to 250mA VIN = 4.5V, ILOAD = 1mA to 250mA 7 12 25 mV mV MAX UNITS 4 4.5 V 1.24 1.24 1.255 1.28 V V 3012bf 2 LT3012B ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25C. PARAMETER CONDITIONS Dropout Voltage VIN = VOUT(NOMINAL) ILOAD = 10mA ILOAD = 10mA MIN (Notes 4, 5) ILOAD = 50mA ILOAD = 50mA ILOAD = 250mA ILOAD = 250mA TYP MAX UNITS 160 230 300 mV mV 250 340 420 mV mV 400 490 620 mV mV 40 3 10 100 A mA mA GND Pin Current VIN = 4.5V (Notes 4, 6) ILOAD = 0mA ILOAD = 100mA ILOAD = 250mA Output Voltage Noise COUT = 10F, ILOAD = 250mA, BW = 10Hz to 100kHz 100 ADJ Pin Bias Current (Note 7) 30 Ripple Rejection VIN = 7V(Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 250mA Current Limit VIN = 7V, VOUT = 0V VIN = 4.5V, VOUT = -0.1V (Note 2) Reverse Output Current (Note 8) VOUT = 1.24V, VIN < 1.24V (Note 2) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3012B is tested and specified for these conditions with the ADJ pin connected to the OUT pin. Note 3: Operating conditions are limited by maximum junction temperature. The regulated output voltage specification will not apply for all possible combinations of input voltage and output current. When operating at maximum input voltage, the output current range must be limited. When operating at maximum output current, the input voltage range must be limited. Note 4: To satisfy requirements for minimum input voltage, the LT3012B is tested and specified for these conditions with an external resistor divider (249k bottom, 549k top) for an output voltage of 4V. The external resistor divider will add a 5A DC load on the output. Note 5: Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage will be equal to (VIN - VDROPOUT). 65 18 VRMS 100 nA 75 dB 400 mA mA 270 12 25 A Note 6: GND pin current is tested with VIN = 4.5V and a current source load. This means the device is tested while operating close to its dropout region. This is the worst-case GND pin current. The GND pin current will decrease slightly at higher input voltages. Note 7: ADJ pin bias current flows into the ADJ pin. Note 8: Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. This current flows into the OUT pin and out the GND pin. Note 9: The LT3012BE is guaranteed to meet performance specifications from 0C to 125C operating junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. Note 10: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 3012bf 3 LT3012B U W TYPICAL PERFOR A CE CHARACTERISTICS Typical Dropout Voltage Guaranteed Dropout Voltage 600 400 TJ = 25C 300 200 100 0 TJ 125C 500 500 400 DROPOUT VOLTAGE (mV) TJ = 125C = TEST POINTS TJ 25C 300 200 100 100 150 200 OUTPUT CURRENT (mA) 0 250 50 150 100 200 OUTPUT CURRENT (mA) Quiescent Current 50 40 30 20 0 50 75 25 TEMPERATURE (C) 100 125 IL = 1mA 1.250 1.245 1.240 1.235 1.230 10 0 50 75 25 TEMPERATURE (C) 100 RL = 1.24k IL = 1mA* 3 4 5 6 7 INPUT VOLTAGE (V) 9 10 3012B G07 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 5 RL = 12.4 IL = 100mA* 3 0 10 VIN = 4.5V 9 TJ = 25C = 1.24V V 8 OUT 6 4 9 GND Pin Current vs ILOAD 2 8 0 10 RL = 4.96 IL = 250mA* 7 7 6 5 4 3 2 1 2 20 3012B G06 TJ = 25C, *FOR VOUT = 1.24V 8 0.4 1 30 0 125 9 GND PIN CURRENT (mA) 0.6 0 40 GND Pin Current RL = 124 IL = 10mA* 0.2 50 3012B G05 TJ = 25C *FOR VOUT = 1.24V 0.8 60 10 1.220 - 50 - 25 GND Pin Current 125 100 TJ = 25C RL = VOUT = 1.24V 70 3012B G04 RL = 49.6 IL = 25mA* 50 25 0 75 TEMPERATURE (C) Quiescent Current 1.225 10 IL = 1mA 80 QUIESCENT CURRENT (A) ADJ PIN VOLTAGE (V) QUIESCENT CURRENT (A) 60 1.0 IL = 10mA 3012B G03 1.255 70 1.2 200 ADJ Pin Voltage 1.260 VIN = 6V 90 RL = I =0 80 L 0 - 50 - 25 IL = 50mA 301B2 G02 100 GND PIN CURRENT (mA) 250 IL = 100mA 300 0 -50 -25 0 50 0 IL = 250mA 400 100 3012B G01 0 Dropout Voltage 600 GND PIN CURRENT (mA) DROPOUT VOLTAGE (mV) 500 GUARANTEED DROPOUT VOLTAGE (mV) 600 1 RL = 24.8, IL = 50mA* 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 3012B G08 0 0 50 100 150 200 LOAD CURRENT (mA) 250 3012B G09 3012bf 4 LT3012B U W TYPICAL PERFOR A CE CHARACTERISTICS Current Limit 45 900 40 800 35 30 25 20 15 300 0 125 TJ = 125C 400 100 100 TJ = 25C 500 5 50 75 25 TEMPERATURE (C) 600 600 200 0 VOUT = 0V 700 10 0 - 50 - 25 Current Limit 700 CURRENT LIMIT (mA) 1000 CURRENT LIMIT (mA) ADJ PIN BIAS CURRENT (nA) ADJ Pin Bias Current 50 10 0 20 30 40 50 60 INPUT VOLTAGE (V) 120 ADJ PIN CLAMP (SEE APPLICATIONS INFORMATION) 40 20 2 3 4 5 6 7 8 OUTPUT VOLTAGE (V) 9 30 25 20 15 10 5 75 50 25 TEMPERATURE (C) 100 0 80 76 72 68 VIN = 4.5V + 0.5VP-P RIPPLE AT f = 120Hz IL = 250mA VOUT = 1.24V 60 -50 -25 125 50 25 0 75 TEMPERATURE (C) 100 125 3012B G18 3012B G17 Minimum Input Voltage 4.0 VIN = 4.5V + 50mVRMS RIPPLE 90 ILOAD = 250mA 70 60 COUT = 10F 40 30 20 0 100k 3.0 2.5 2.0 1.5 1.0 0.5 COUT = 3.3F 1k 10k FREQUENCY (Hz) ILOAD = 250mA 3.5 80 100 84 64 0 - 50 - 25 10 125 100 88 Input Ripple Rejection 10 50 25 0 75 TEMPERATURE (C) 3012B G15 VIN = 0V VOUT = VADJ = 1.24V 100 10 0 -50 -25 80 Input Ripple Rejection 3012B G16 50 VIN = 7V VOUT = 0V 92 MINIMUM INPUT VOLTAGE (V) 1 70 RIPPLE REJECTION (dB) REVERSE OUTPUT CURRENT (A) 140 RIPPLE REJECTION (dB) REVERSE OUTPUT CURRENT (A) 35 TJ = 25C 180 VIN = 0V VOUT = VADJ 160 0 200 Reverse Output Current Reverse Output Current 0 300 3012B G14 200 60 400 100 3012B G13 100 CURRENT FLOWS 80 INTO OUTPUT PIN 500 1M 3012B G19 0 - 50 - 25 0 50 75 25 TEMPERATURE (C) 100 125 3012B G20 3012bf 5 LT3012B U W TYPICAL PERFOR A CE CHARACTERISTICS Load Regulation 0 COUT = 3.3F ILOAD = 250mA -2 LOAD REGULATION (mV) OUTPUT NOISE SPECTRAL DENSITY (V/Hz) Output Noise Spectral Density 10 1 0.1 IL = 1mA TO 250mA -4 -6 -8 -10 -12 -14 -16 -18 0.01 10 100 1k 10k FREQUENCY (Hz) -20 - 50 - 25 100k 75 50 25 TEMPERATURE (C) 0 100 3012B G22 125 3012B G21 10Hz to 100kHz Output Noise Transient Response VOUT 100V/DIV COUT = 10F IL = 250mA VOUT = 1.24V 1ms/DIV 3012B G23 LOAD CURRENT (mA) OUTPUT VOLTAGE DEVIATION (V) 0.15 0.10 0.05 0 -0.05 VIN = 6V VOUT = 5V CIN = 3.3F CERAMIC COUT = 3.3F CERAMIC ILOAD = 100mA TO 200mA -0.10 -0.15 300 200 100 0 0 100 300 200 TIME (s) 400 500 3012B G24 3012bf 6 LT3012B U U U PI FU CTIO S (DFN Package)/(TSSOP Package) OUT (Pins 2, 3)/(Pins 3, 4): Output. The output supplies power to the load. A minimum output capacitor of 3.3F is required to prevent oscillations. Larger output capacitors will be required for applications with large transient loads to limit peak voltage transients. See the Applications Information section for more information on output capacitance and reverse output characteristics. ADJ (Pin 4)/(Pin 5): Adjust. This is the input to the error amplifier. This pin is internally clamped to 7V. It has a bias current of 30nA which flows into the pin (see curve of ADJ Pin Bias Current vs Temperature in the Typical Performance Characteristics). The ADJ pin voltage is 1.24V referenced to ground, and the output voltage range is 1.24V to 60V. GND (Pins 5, 13)/(Pins 1, 6, 8, 9, 16, 17): Ground. The exposed backside of the package is an electrical connection for GND. As such, to ensure optimum device operation and thermal performance, the exposed pad must be connected directly to pin 5/pin 6 on the PC board. IN (Pins 10, 11)/(Pins 13,14): Input. Power is supplied to the device through the IN pin. A bypass capacitor is required on this pin if the device is more than six inches away from the main input filter capacitor. In general, the output impedance of a battery rises with frequency, so it is advisable to include a bypass capacitor in batterypowered circuits. A bypass capacitor in the range of 1F to 10F is sufficient. The LT3012B is designed to withstand reverse voltages on the IN pin with respect to ground and the OUT pin. In the case of a reversed input, which can happen if a battery is plugged in backwards, the LT3012B will act as if there is a diode in series with its input. There will be no reverse current flow into the LT3012B and no reverse voltage will appear at the load. The device will protect both itself and the load. NC (Pins 1, 6-9, 12)/(Pins 2, 7, 10-12, 15): No Connect. No Connect pins may be floated, tied to IN or tied to GND. 3012bf 7 LT3012B U W U U APPLICATIO S I FOR ATIO The LT3012B is a 250mA high voltage low dropout regulator with micropower quiescent current. The device is capable of supplying 250mA at a dropout voltage of 400mV. Operating quiescent current is only 40A. In addition to the low quiescent current, the LT3012B incorporates several protection features which make it ideal for use in battery-powered systems. The device is protected against both reverse input and reverse output voltages. In battery backup applications where the output can be held up by a backup battery when the input is pulled to ground, the LT3012B acts like it has a diode in series with its output and prevents reverse current flow. Adjustable Operation The LT3012B has an output voltage range of 1.24V to 60V. The output voltage is set by the ratio of two external resistors as shown in Figure 1. The device servos the output to maintain the voltage at the adjust pin at 1.24V referenced to ground. The current in R1 is then equal to 1.24V/R1 and the current in R2 is the current in R1 plus the ADJ pin bias current. The ADJ pin bias current, 30nA at 25C, flows through R2 into the ADJ pin. The output voltage can be calculated using the formula in Figure 1. The value of R1 should be less than 250k to minimize errors in the output voltage caused by the ADJ pin bias current. The adjustable device is tested and specified with the ADJ pin tied to the OUT pin and a 5A DC load (unless otherwise specified) for an output voltage of 1.24V. Specifications for output voltages greater than 1.24V will be proportional IN VIN to the ratio of the desired output voltage to 1.24V; (VOUT/ 1.24V). For example, load regulation for an output current change of 1mA to 250mA is -7mV typical at VOUT = 1.24V. At VOUT = 12V, load regulation is: (12V/1.24V) * (-7mV) = -68mV Output Capacitance and Transient Response The LT3012B is designed to be stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 3.3F with an ESR of 3 or less is recommended to prevent oscillations. The LT3012B is a micropower device and output transient response will be a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current changes. Bypass capacitors, used to decouple individual components powered by the LT3012B, will increase the effective output capacitor value. Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but they tend to have strong voltage and temperature coefficients as shown in Figures 2 and 3. When used with a 5V regulator, a 16V 10F Y5V capacitor OUT R2 LT3012B C1 + VOUT ADJ GND R1 3012B F01 ( ) VOUT = 1.24V 1 + R2 + (IADJ)(R2) R1 VADJ = 1.24V IADJ = 30nA AT 25C OUTPUT RANGE = 1.24V TO 60V Figure 1. Adjustable Operation 3012bf 8 LT3012B U W U U APPLICATIO S I FOR ATIO can exhibit an effective value as low as 1F to 2F for the DC bias voltage applied and over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. Care still must be exercised when using X5R and X7R capacitors; the X5R and X7R codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance change due to DC bias with X5R and X7R capacitors is better than Y5V and Z5U capacitors, but can still be significant enough to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component case size increases, but expected capacitance at operating voltage should be verified. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be induced by vibrations in the system or thermal transients. Current Limit and Safe Operating Area Protection Like many IC power regulators, the LT3012B has safe operating area protection. The safe operating area protection decreases the current limit as the input voltage increases and keeps the power transistor in a safe operat20 ing region. The protection is designed to provide some output current at all values of input voltage up to the device breakdown (see curve of Current Limit vs Input Voltage in the Typical Performance Characteristics). The LT3012B is limited for operating conditions by maximum junction temperature. While operating at maximum input voltage, the output current range must be limited; when operating at maximum output current, the input voltage range must be limited. Device specifications will not apply for all possible combinations of input voltage and output current. Operating the LT3012B beyond the maximum junction temperature rating may impair the life of the device. Thermal Considerations The power handling capability of the device will be limited by the maximum rated junction temperature (125C). The power dissipated by the device will be made up of two components: 1. Output current multiplied by the input/output voltage differential: IOUT * (VIN - VOUT) and, 2. GND pin current multiplied by the input voltage: IGND * VIN. The GND pin current can be found by examining the GND Pin Current curves in the Typical Performance Characteristics. Power dissipation will be equal to the sum of the two components listed above. 40 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F 20 X5R CHANGE IN VALUE (%) CHANGE IN VALUE (%) 0 -20 -40 -60 Y5V -80 -100 0 X5R -20 -40 Y5V -60 -80 0 2 4 8 6 10 12 DC BIAS VOLTAGE (V) 14 16 3012B F02 Figure 2. Ceramic Capacitor DC Bias Characterics BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F -100 50 25 75 -50 -25 0 TEMPERATURE (C) 100 125 3012B F03 Figure 3. Ceramic Capacitor Temperature Characterics 3012bf 9 LT3012B U W U U APPLICATIO S I FOR ATIO The LT3012B has internal thermal limiting designed to protect the device during overload conditions. For continuous normal conditions the maximum junction temperature rating of 125C must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. Additional heat sources mounted nearby must also be considered. For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes can also be used to spread the heat generated by power devices. The following tables list thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 3/32" FR-4 board with one ounce copper. Table 1. DFN Measured Thermal Resistance COPPER AREA TOPSIDE BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 2500 sq mm 2500 sq mm 2500 sq mm 40C/W 1000 sq mm 2500 sq mm 2500 sq mm 45C/W 225 sq mm 2500 sq mm 2500 sq mm 50C/W 100 sq mm 2500 sq mm 2500 sq mm 62C/W Table 2. TSSOP Measured Thermal Resistance COPPER AREA Continuous operation at large input/output voltage differentials and maximum load current is not practical due to thermal limitations. Transient operation at high input/ output differentials is possible. The approximate thermal time constant for a 2500sq mm 3/32" FR-4 board with maximum topside and backside area for one ounce copper is 3 seconds. This time constant will increase as more thermal mass is added (i.e. vias, larger board, and other components). For an application with transient high power peaks, average power dissipation can be used for junction temperature calculations as long as the pulse period is significantly less than the thermal time constant of the device and board. Calculating Junction Temperature Example 1: Given an output voltage of 5V, an input voltage range of 24V to 30V, an output current range of 0mA to 50mA, and a maximum ambient temperature of 50C, what will the maximum junction temperature be? The power dissipated by the device will be equal to: IOUT(MAX) * (VIN(MAX) - VOUT) + (IGND * VIN(MAX)) where: IOUT(MAX) = 50mA TOPSIDE BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 2500 sq mm 2500 sq mm 2500 sq mm 40C/W 1000 sq mm 2500 sq mm 2500 sq mm 45C/W 225 sq mm 2500 sq mm 2500 sq mm 50C/W 100 sq mm 2500 sq mm 2500 sq mm 62C/W The thermal resistance junction-to-case (JC), measured at the exposed pad on the back of the die, is 16C/W. VIN(MAX) = 30V IGND at (IOUT = 50mA, VIN = 30V) = 1mA So: P = 50mA * (30V - 5V) + (1mA * 30V) = 1.28W The thermal resistance will be in the range of 40C/W to 62C/W depending on the copper area. So the junction temperature rise above ambient will be approximately equal to: 1.31W * 50C/W = 65.5C 3012bf 10 LT3012B U W U U APPLICATIO S I FOR ATIO The maximum junction temperature will then be equal to the maximum junction temperature rise above ambient plus the maximum ambient temperature or: TJMAX = 50C + 65.5C = 115.5C Example 2: Given an output voltage of 5V, an input voltage of 48V that rises to 72V for 5ms(max) out of every 100ms, and a 5mA load that steps to 50mA for 50ms out of every 250ms, what is the junction temperature rise above ambient? Using a 500ms period (well under the time constant of the board), power dissipation is as follows: P1(48V in, 5mA load) = 5mA * (48V - 5V) + (200A * 48V) = 0.23W P2(48V in, 50mA load) = 50mA * (48V - 5V) + (1mA * 48V) = 2.20W P3(72V in, 5mA load) = 5mA * (72V - 5V) + (200A * 72V) = 0.35W P4(72V in, 50mA load) = 50mA * (72V - 5V) + (1mA * 72V) = 3.42W Operation at the different power levels is as follows: 76% operation at P1, 19% for P2, 4% for P3, and 1% for P4. PEFF = 76%(0.23W) + 19%(2.20W) + 4%(0.35W) + 1%(3.42W) = 0.64W With a thermal resistance in the range of 40C/W to 62C/W, this translates to a junction temperature rise above ambient of 26C to 38C. Protection Features The LT3012B incorporates several protection features which make it ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the device is protected against reverse-input voltages, and reverse voltages from output to input. Current limit protection and thermal overload protection are intended to protect the device against current overload conditions at the output of the device. For normal operation, the junction temperature should not exceed 125C. The input of the device will withstand reverse voltages of 80V. No negative voltage will appear at the output. The device will protect both itself and the load. This provides protection against batteries which can be plugged in backward. The ADJ pin of the device can be pulled above or below ground by as much as 7V without damaging the device. If the input is left open circuit or grounded, the ADJ pin will act like an open circuit when pulled below ground, and like a large resistor (typically 100k) in series with a diode when pulled above ground. If the input is powered by a voltage source, pulling the ADJ pin below the reference voltage will cause the device to current limit. This will cause the output to go to a unregulated high voltage. Pulling the ADJ pin above the reference voltage will turn off all output current. 3012bf 11 LT3012B U W U U APPLICATIO S I FOR ATIO In situations where the ADJ pin is connected to a resistor divider that would pull the ADJ pin above its 7V clamp voltage if the output is pulled high, the ADJ pin input current must be limited to less than 5mA. For example, a resistor divider is used to provide a regulated 1.5V output from the 1.24V reference when the output is forced to 60V. The top resistor of the resistor divider must be chosen to limit the current into the ADJ pin to less than 5mA when the ADJ pin is at 7V. The 53V difference between the OUT and ADJ pins divided by the 5mA maximum current into the ADJ pin yields a minimum top resistor value of 10.6k. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage, or is left open circuit. Current flow back into the output will follow the curve shown in Figure 4. The rise in reverse output current above 7V occurs from the breakdown of the 7V clamp on the ADJ pin. With a resistor divider on the regulator output, this current will be reduced depending on the size of the resistor divider. When the IN pin of the LT3012B is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current will typically drop to less than 2A. This can happen if the input of the LT3012B is connected to a discharged (low voltage) battery and the output is held up by either a backup battery or a second regulator circuit. REVERSE OUTPUT CURRENT (A) 200 TJ = 25C 180 VIN = 0V VOUT = VADJ 160 140 120 100 CURRENT FLOWS 80 INTO OUTPUT PIN ADJ PIN CLAMP (SEE ABOVE) 60 40 20 0 0 1 2 3 4 5 6 7 8 OUTPUT VOLTAGE (V) 9 10 3012B F04 Figure 4. Reverse Output Current 3012bf 12 LT3012B U TYPICAL APPLICATIO S LT3012B Automotive Application VIN 12V (LATER 42V) IN + 1F NO PROTECTION DIODE NEEDED! OUT LT3012B 750k 3.3F ADJ GND LOAD: CLOCK, SECURITY SYSTEM ETC 249k LT3012B Telecom Application VIN 48V (72V TRANSIENT) IN OUT LT3012B 1F ADJ GND 750k NO PROTECTION DIODE NEEDED! + 3.3F LOAD: SYSTEM MONITOR ETC - BACKUP BATTERY 249k 3012B TA05 Constant Brightness for Indicator LED over Wide Input Voltage Range RETURN IN 1F OUT LT3012B 3.3F ADJ GND -48V ILED = 1.24V/RSET -48V CAN VARY FROM -4V TO -80V RSET 3012B TA06 3012bf 13 LT3012B U PACKAGE DESCRIPTIO DE/UE Package 12-Lead Plastic DFN (4mm x 3mm) (Reference LTC DWG # 05-08-1695 Rev C) 0.70 0.05 3.60 0.05 1.70 0.05 2.20 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 3.30 0.05 (2 SIDES) 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4.00 0.10 (2 SIDES) 7 R = 0.115 TYP 0.40 0.10 12 R = 0.05 TYP PIN 1 TOP MARK (NOTE 6) 0.200 REF 3.00 0.10 (2 SIDES) 1.70 0.05 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.35 x 45 CHAMFER 0.75 0.05 0.00 - 0.05 6 0.25 0.05 3.30 0.05 (2 SIDES) 1 (UE12/DE12) DFN 0905 REV C 0.50 BSC BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE A VARIATION OF VERSION (WGED) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3012bf 14 LT3012B U PACKAGE DESCRIPTIO FE Package 16-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663) Exposed Pad Variation BB 4.90 - 5.10* (.193 - .201) 3.58 (.141) 3.58 (.141) 16 1514 13 12 1110 6.60 0.10 9 2.94 (.116) 4.50 0.10 2.94 6.40 (.116) (.252) BSC SEE NOTE 4 0.45 0.05 1.05 0.10 0.65 BSC 1 2 3 4 5 6 7 8 RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 0.25 REF 1.10 (.0433) MAX 0 - 8 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE16 (BB) TSSOP 0204 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3012bf Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LT3012B RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1020 125mA, Micropower Regulator and Comparator VIN: 4.5V to 36V, VOUT(MIN) = 2.5V, VDO = 0.4V, IQ = 40A, ISD = 40A, Comparator and Reference, Class B Outputs, S16, PDIP14 Packages LT1120/LT1120A 125mA, Micropower Regulator and Comparator VIN: 4.5V to 36V, VOUT(MIN) = 2.5V, VDO = 0.4V, IQ = 40A, ISD = 10A, Comparator and Reference, Logic Shutdown, Ref Sources and Sinks 2/4mA, S8, N8 Packages LT1121/ LT1121HV 150mA, Micropower, LDO VIN: 4.2V to 30/36V, VOUT(MIN) = 3.75V, VDO = 0.42V, IQ = 30A, ISD = 16A, Reverse Battery Protection, SOT-223, S8, Z Packages LT1129 700mA, Micropower, LDO VIN: 4.2V to 30V, VOUT(MIN) = 3.75V, VDO = 0.4V, IQ = 50A, ISD = 16A, DD, S0T-223, S8,TO220-5, TSSOP20 Packages LT1676 60V, 440mA (IOUT), 100kHz, High Efficiency Step-Down DC/DC Converter VIN: 7.4V to 60V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 2.5A, S8 Package LT1761 100mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 20A, ISD = <1A, Low Noise < 20VRMS, Stable with 1F Ceramic Capacitors, ThinSOT Package LT1762 150mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 25A, ISD = <1A, Low Noise < 20VRMS, MS8 Package LT1763 500mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.3V, IQ = 30A, ISD = <1A, Low Noise < 20VRMS, S8 Package LT1764/LT1764A 3A, Low Noise, Fast Transient Response, LDO VIN: 2.7V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = <1A, Low Noise < 40VRMS, "A" Version Stable with Ceramic Capacitors, DD, TO220-5 Packages LT1766 60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25A, TSSOP16/E Package LT1776 40V, 550mA (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN: 7.4V to 40V, VOUT(MIN) = 1.24V, IQ = 3.2mA, ISD = 30A, N8, S8 Packages LT1934/ LT1934-1 300mA/60mA, (IOUT), Constant Off-Time, High Efficiency Step-Down DC/DC Converter 90% Efficiency, VIN: 3.2V to 34V, VOUT(MIN) = 1.25V, IQ = 14A, ISD = <1A, ThinSOT Package LT1956 60V, 1.2A (IOUT), 500kHz, High Efficiency Step-Down DC/DC Converter VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25A, TSSOP16/E Package LT1962 300mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.27V, IQ = 30A, ISD = <1A, Low Noise < 20VRMS, MS8 Package LT1963/LT1963A 1.5A, Low Noise, Fast Transient Response, LDO VIN: 2.1V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = <1A, Low Noise < 40VRMS, "A" Version Stable with Ceramic Capacitors, DD, TO220-5, S0T-223, S8 Packages LT1964 200mA, Low Noise Micropower, Negative LDO VIN: -1.9V to -20V, VOUT(MIN) = -1.21V, VDO = 0.34V, IQ = 30A, ISD = 3A, Low Noise < 30VRMS, Stable with Ceramic Capacitors, ThinSOT Package LT3010 100mA, 3V to 80V, Low Noise Micropower LDO VIN: 3V to 8V, VOUT(MIN) = 1.275V, VDO = 0.3V, IQ = 30A, ISD = 1A, Low Noise < 100VRMS, MS8E Package 3012bf 16 Linear Technology Corporation LT 0206 * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2006