Click on Series name for product info on aimtec.com Series AMEPR8D-AZ up to 0.7A | AC-DC LED Driver FEATURES: * * * * * * * * * * AC-DC Constant Current LED Driver Input Range 90-264VAC/47-440Hz High Efficiency up to 80% Operating Temperature -20 to 85C Total Harmonic Distortion < 20% Class 2 Power Supply Active PFC SCP, Over Load Protection Leading or Trailing Edge Triac IP67 Case Models Single output Model Max Output Power (W) Output Voltage Range (V) No Load Output Voltage (V max.) Output Current (A) Input Voltage (VAC/Hz) 8.4 7.2 8.4 12-24 9-18 6-12 34 20 15 0.35 0.4 0.7 90-264/47-440 90-264/47-440 90-264/47-440 AMEPR8D-2435AZ AMEPR8D-1840AZ AMEPR8D-1270AZ Efficiency (%) 115 VAC 230 VAC 79 77 75 80 79 78 *Exceeding the maximum output power will permanently damage the converter. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. AMEPR8D-AZ's AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to `dirty' electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Current (full load) Inrush current <2ms (cold start) Leakage current Power factor External fuse Start-up time Conditions Typical 115 VAC 230 VAC 115 VAC 230 VAC 230 VAC 115 VAC (full load) 230 VAC (full load) Recommended slow blow type Maximum 85 50 10 5 0.02 Units mA mA A A mA 0.98 0.95 1 100 A ms Output Specifications Parameters Current accuracy Line regulation Load regulation Ripple & Noise* Hold-up time Minimum load voltage Maximum Capacitive Load Conditions Typical Maximum 15 0.5 5 1.6 28 (LL-HL) min.-max. load Units % % % V p-p ms See the models table 200 F *Ripple and Noise are measured at 20MHz bandwidth by using a 0.1F (M/C) or (C/C) and 220F (E/C) parallel capacitor. www.aimtec.com F 052.1e R3.H Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR8D-AZ up to 0.7A | AC-DC LED Driver Isolation Specifications Parameters Conditions Tested I/O voltage Isolation resistance Typical Maximum Units 3000 VAC M 3sec >1000 General Specifications Parameters Conditions Switching frequency Over load protection Over voltage protection Short circuit protection Operating temperature Storage temperature Maximum case temperature Temperature coefficient Cooling Humidity Case material Potting Wires Weight Dimensions (D X L) MTBF Typical With derating over 75C Maximum 66 110 110 Auto recovery Refer to model application -40 to +95 KHz % % oC oC 100 0.02 Free air convection Non condensing 20~95 Plastic Epoxy (IP67 rated) UL1015 Input 18AWG*10CM / Output 20 AWG*10CM 55 27.4 x 70.3 mm (1.08 x 2.77 inches) >400,000 hrs (MIL-HDBK-217F at +25C) Units oC % / oC % RH g Environment Approval Test Shock Vibration Parameters Conditions Wave form Acceleration amplitude Bump duration Converter operation Number of bumps Test mode Displacement Acceleration Converter operation Half sine wave 5gn 30ms Before and after test, body mounted (on chassis) 18 (3 in each direction for every axis) Sweep sine, 10-100Hz, speed 0.05Hz/s 1mm 3g, 3 loops 30min one cycle, 3h total, every axis tested Before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals Standards cULus, FCC UL8750, UL60950-1, class 2 power supply per UL1310, FCC15, Wire Specifications Wire Parameters Color ACN ACL +V Output -V Output Blue Brown Red Black Input Output www.aimtec.com F 052.1e R3.H Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR8D-AZ up to 0.7A | AC-DC LED Driver Dimensions Derating Free Air Convection 75 C 100 80 60 Safe Operating Area 40 20 0 - 20 0 20 40 60 80 85 100 Ambient Temperature C www.aimtec.com F 052.1e R3.H Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR8D-AZ up to 0.7A | AC-DC LED Driver Triac Dimming Feature NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 052.1e R3.H Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only