SIDACtor® Protection Thyristors
93
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Fixed Voltage TwinSLIC™ Series - Modified DO-214
Electrical Characteristics
Fixed Voltage Series Modified DO-214 are uni-
directional SIDACtor® devices designed to protect
SLICs (Subscriber Line Interface Circuit) from damaging
overvoltage transients.
The series provides single port protection using fixed
voltage switching devices for negative surges. All
positive surges are routed through internal diodes to a
ground reference.
Description
Features and Benefits
t Low voltage overshoot
t Low on-state voltage
t Does not degrade with use
t Fails short circuit when
surged in excess of ratings
t Integrated diodes for
positive voltage surges
t Single-port protection
Agency Approvals
Agency Agency File Number
E133083
Schematic Symbol
Pinout Designation
Part Number Marking
VDRM
@lDRM=5μA
VS
@100V/μs IHISIT
VT
@IT=2.2 Amps VF
Capacitance
V min V max mA min mA max A max V max V max
Pin 1-2, 3-2
P0641CA2LRP P62A 58 77 120 800 2.2 4 5
See
Capacitance
Values table
P0721CA2LRP P72A 65 88 120 800 2.2 4 5
P0901CA2LRP P92A 75 98 120 800 2.2 4 5
P1101CA2LRP P02A 95 130 120 800 2.2 4 5
P1301CA2LRP P131A 120 160 120 800 2.2 4 5
P1701CA2LRP P17A 160 200 120 800 2.2 4 5
Pin 3
Pin 1
Pin 2
Applicable Global Standards
t TIA-968-A
t TIA-968-B
t ITU K.20/21 Enhanced
Level
t ITU K.20/21 Basic Level
t GR 1089 Inter-building*
t GR 1089 Intra-building*
t IEC 61000-4-5
t YD/T 1082
t YD/T 993
t YD/T 950
* Series resistance required
Notes:
- Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted).
- Devices are uni-directional
1
3
2
(T)
(G)
(R)
SIDACtor® Protection Thyristors
94
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Package Symbol Parameter Value Unit
Modified DO-214AA
Pin 3
Pin 1
Pin 2
TJOperating Junction Temperature Range UP °C
TSStorage Temperature Range UP °C
R0JA Thermal Resistance: Junction to Ambient 85 °C/W
Series
Surge Ratings
Series
IPP ITSM
50/60 Hz
di/dt
0.2x310 1
0.5x700 2
2x10 1
2x10 2
8x20 1
1.2x50 2
10x160 1
10x160 2
10x560 1
10x560 2
5x320 1
9x720 2
10x360 1
10x360 2
10x1000 1
10x1000 2
5x310 1
10x700 2
A min A min A min A min A min A min A min A min A min A min A/μs max
A20 15015090 507575 45 7520500
Thermal Considerations
Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias.
Capacitance Values
Part Number
pF
Pin 1-2 / 3-2
Tip-Ground, Ring-Ground
pF
Pin 1-3
Tip-Ring
MIN MAX MIN MAX
P0641CA2LRP 40 70 20 45
P0721CA2LRP 35 70 20 45
P0901CA2LRP 30 65 20 40
P1101CA2LRP 25 55 15 35
P1301CA2LRP 25 45 15 30
P1701CA2LRP 25 40 15 25
Notes:
1 Current waveform in μs
2 Voltage waveform in μs
50
100
0
t
r
t
d
0
Peak
Value
Half Value
t – Time (μs)
I
PP
– Peak Pulse Current – %I
PP
t
r
= rise time to peak value
t
d
= decay time to half value
Waveform = t
r
x t
d
tr x td Pulse Waveform
V-I Characteristics
I
H
I
DRM
V
DRM
V
T
+V
+I
V
S
I
S
I
T
V
F
-V
-I
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product.
- IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$
- The device must initially be in thermal equilibrium with -40°C < TJ <¡$
SIDACtor® Protection Thyristors
95
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
25°C
Case Temperature (TC) - ºC
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100 120 140 160
Ratio of IH
IH (TC = 25ºC)
Normalized VS Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
Time
Temperature
T
P
T
L
T
S(max)
T
S(min)
25
t
P
t
L
t
S
time to peak temperature
(t 25ºC to peak)
Ramp-down
Ramp-up
Preheat
Critical Zone
T
L
to T
P
Figure 1
Soldering Parameters
Physical Specifications Environmental Specifications
Lead Material Copper Alloy
Terminal Finish 100% Matte-Tin Plated
Body Material UL recognized epoxy meeting flammability
classification 94V-0
High Temp Voltage
Blocking
80% Rated VDRM (VAC 1FBL¡$PS¡$
or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC,
JESD22-A-101
Temp Cycling
¡$UP¡$NJOEXFMMVQUP
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
Biased Temp &
Humidity
52 VDC¡$3)VQUPIST&*"
JEDEC, JESD22-A-101
High Temp Storage ¡$IST.*-45%.FUIPE
JEDEC, JESD22-A-101
Low Temp Storage -65°C, 1008 hrs.
Thermal Shock
¡$UP¡$NJOEXFMMTFDUSBOTGFS
10 cycles. MIL-STD-750 (Method 1056) JEDEC,
JESD22-A-106
Autoclave (Pressure
Cooker Test)
¡$3)BUNVQUPIST&*"
JEDEC, JESD22-A-102
Resistance to
Solder Heat ¡$TFDT.*-45%.FUIPE
Moisture
Sensitivity Level
3)¡$ISTSFnPXDZDMFT¡$
peak). JEDEC-J-STD-020, Level 1
Reflow Condition Pb-Free assembly
(see Fig. 1)
Pre Heat
- Temperature Min (Ts(min))¡$
- Temperature Max (Ts(max))¡$
- Time (Min to Max) (ts)60-180 secs.
Average ramp up rate (Liquidus Temp (TL)
to peak) 3°C/sec. Max.
TS(max) to TL - Ramp-up Rate 3°C/sec. Max.
Reflow
- Temperature (TL) (Liquidus) ¡$
- Temperature (tL)60-150 secs.
Peak Temp (TP)¡$
Time within 5°C of actual Peak Temp (tp)30 secs. Max.
Ramp-down Rate 6°C/sec. Max.
Time 25°C to Peak Temp (TP)8 min. Max.
Do not exceed ¡$
-8
-40 -20 0 20 40 60 80 100 120 140 160
-6
-4
0
2
4
6
8
10
12
14
Junction Temperature (T
J
) – °C
Percent of V
S
Change – %
25 °C
SIDACtor® Protection Thyristors
96
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Part Marking
Part Numbering
XXXXX Part number code
(refer to Electrical Characteristics table)
Date code
XXXXX
P A L RPxxx1 C
CONSTRUCTION VARIABLE
REEL PACK
PACKAGE TYPE
RoHS COMPLIANT
TYPE
P = SIDACtor
MEDIAN VOLTAGE
2
TwinSLIC IDENTIFIER
(two chip device)
I
PP
RATING
Packing Options
Tape and Reel Specification — Modified DO-214AA
Dimensions — Modified DO-214AA
0.079
(2.0)
0.040
(1.0)
0.030
(0.76)
0.079
(2.0)
0.079
(2.0)
0.110
(2.8)
Pad Outline
(MM)
H
K
JE
F
G
AC
B
M
D
NP
PIN 3
PIN 1
PIN 2
Dimensions are in inches
(and millimeters).
Package Type Description Quantity Added Suffix Industry Standard
CModified DO-214AA 3-leaded
Tape and Reel Pack 2500 RP EIA-481-D
0.49
(12.4)
0.512 (13.0)
Arbor Hole Dia.
12.99
(330.0) Dimensions are in inches
(and millimeters).
Direction of Feed
0.472
(12.0)
0.360
(9.2)
0.315
(8.0)
0.157
(4.0) Pin 2
Pin 1 Pin 3 Dimensions are in inches
(and millimeters).
Dimensions Inches Millimeters
Min Max Min Max
A 0.130 0.156 3.30 3.95
B 0.201 0.220 5.10 5.60
C 0.077 0.087 1.95 2.20
D 0.159 0.181 4.05 4.60
E 0.030 0.063 0.75 1.60
F 0.075 0.096 1.90 2.45
G 0.002 0.008 0.05 0.20
H 0.077 0.104 1.95 2.65
K 0.006 0.016 0.15 0.41
M0.022 0.028 0.56 0.71
N0.027 0.033 0.69 0.84
P0.052 0.058 1.32 1.47