W24010 128K x 8 CMOS STATIC RAM GENERAL DESCRIPTION The W24010 is a normal-speed, very low-power CMOS static RAM organized as 131072 x 8 bits that operates on a wide voltage range from 2.7V to 5.5V power supply. The W24010 family, W2401070LE and W24010-70LI, can meet the requirement of various operating temperature. This device is manufactured using Winbond's high performance CMOS technology. FEATURES * * * * * Low power consumption: - Active: 350 mW (max.) - Standby: 15 W (max.) /3V 50 W (max.) /5V Access time: 70 nS (max.) /5V 100 nS (max.) /3V Single 3V/5V power supply Fully static operation * * * * PIN CONFIGURATIONS All inputs and outputs directly TTL compatible Three-state outputs Battery back-up operation capability Data retention voltage: 2V (min.) Packaged in 32-pin 600 mil DIP, 450 mil SOP, standard type one TSOP (8 mm x 20 mm) and small type one TSOP (8 mm x 13.4 mm) BLOCK DIAGRAM CLK GEN. PRECHARGE CKT. R O W CORE CELL ARRAY A16 1 32 VDD A16 2 31 A15 A14 3 30 CS2 NC A14 A12 A4 A3 A2 A12 4 29 A7 5 28 A13 A6 6 27 A8 A5 7 26 A9 A4 8 25 A11 A3 9 24 OE A2 10 23 A10 A1 11 22 CS1 WE A0 12 21 I/O8 CS1 CS2 I/O1 13 20 I/O7 OE I/O2 14 19 I/O6 I/O3 15 18 I/O5 VSS 16 17 I/O4 WE A7 A6 A11 A9 A8 A13 WE CS2 A15 VDD NC A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32-pin TSOP 1024 ROWS D E C O D E R 128 X 8 COLUMNS A5 A9 I/O1 : I/O8 DATA CNTRL. I/O CKT. COLUMN DECODER CLK GEN. A15 A13 A8 A1 A0 A11A10 PIN DESCRIPTION 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 SYMBOL A0-A16 I/O1-I/O8 OE A10 CS1 I/O8 I/O7 I/O6 I/O5 I/O4 VSS I/O3 I/O2 I/O1 A0 A1 A2 A3 CS1, CS2 WE OE VDD VSS NC -1- DESCRIPTION Address Inputs Data Inputs/Outputs Chip Select Input Write Enable Input Output Enable Input Power Supply Ground No Connection Publication Release Date: November 1998 Revision A6 W24010 TRUTH TABLE CS1 H CS2 MODE VDD CURRENT I/O1-I/O8 X OE X WE X Not Selected High Z ISB, ISB1 X L X X Not Selected High Z ISB, ISB1 L H H H Output Disable High Z IDD L H L H Read Data Out IDD L H X L Write Data In IDD DC CHARACTERISTICS Absolute Maximum Ratings PARAMETER RATING UNIT -0.5 to +7.0 V Input/Output to VSS Potential -0.5 to VDD +0.5 V Allowable Power Dissipation 1.0 W -65 to +150 C LE -20 to 85 C LI -40 to 85 C Supply Voltage to VSS Potential Storage Temperature Operating Temperature Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. Operating Characteristics (VDD = 5V 10%; VDD = 3V 10%; VSS = 0V; TA (C) =-20 to 85 for LE, -40 to 85 for LI) PARAMETER SYM. TEST CONDITIONS 5V 3V UNIT MIN. TYP.* MAX. MIN. TYP.* MAX. Input Low Voltage VIL - -0.5 - +0.8 -0.5 - +0.6 V Input High Voltage VIH - +2.2 - VDD +0.5 +2.0 - VDD +0.5 V Input Leakage Current ILI VIN = VSS to VDD -1 - +1 -1 - +1 A Output Leakage Current ILO VI/O = VSS to VDD, CS1 = VIH (min.) or CS2 = VIL (max.) -1 - +1 -1 - +1 A or OE = VIH (min.) or WE = VIL (max.) Output Low Voltage VOL IOL = +2.1 mA - - 0.4 - - 0.4 V Output High Voltage VOH IOH = -1.0 mA 2.4 - - 2.2 - - V -2- W24010 Operating Characteristics, continued PARAMETER SYM. TEST CONDITIONS 5V 3V UNIT MIN. - TYP.* - MAX. 70 MIN. - TYP.* - MAX. 30 mA Operating Power Supply Current IDD CS1 = VIL (max.) and CS2 = VIH (min.) I/O = 0 mA Cycle = min. Duty = 100% Standby Power Supply Current ISB CS1 = VIH (min.) or CS2 = VIL (max.) Cycle = min. Duty = 100% - - 3 - - 1 mA ISB1 CS1 VDD -0.2V or CS2 0.2V - 1.0 10 - 0.5 5 A Note: Typical parameter is measured under ambient temperature TA = 25 C and VDD = 5V/ 3V CAPACITANCE (VDD = 5 V, TA = 25 C, f = 1 MHz) PARAMETER Input Capacitance Input/Output Capacitance SYM. CIN CI/O CONDITIONS VIN = 0V VOUT = 0V MAX. 6 8 UNIT pF pF Note: These parameters are sampled but not 100% tested. AC Characteristics AC Test Conditions PARAMETER Input Pulse Levels CONDITIONS 3V 5V Input Rise and Fall Times Input and Output Timing Reference Level Output Load 0V to 2.4V 0V to 3.0V 5 nS 1.5V See the drawing below AC Test Loads and Waveform 1 TTL 1 TTL OUTPUT OUTPUT 100 pF Including Jig and Scope 5 pF Including Jig and Scope (For TCLZ, TOLZ, TCHZ, TOHZ, TWHZ, TOW ) 2.4 V / 3.0 V 90% 0V 10% 90% 10% 5 nS 5 nS -3- Publication Release Date: November 1998 Revision A6 W24010 AC Characteristics, continued (VDD = 5 V 10%; VDD = 3 V 10%; VSS = 0 V; TA (C) =-20 to 85 for LE, -40 to 85 for LI) Read Cycle PARAMETER SYM. 5V 3V UNIT MIN. MAX. MIN. MAX. Read Cycle Time TRC 70 - 100 - nS Address Access Time TAA - 70 - 100 nS Chip Select Access Time TACS - 70 - 100 nS Output Enable to Output Valid TAOE - 35 - 50 nS Chip Selection to Output in Low Z TCLZ* 10 - 15 - nS Output Enable to Output in Low Z TOLZ* 5 - 5 - nS Chip Deselection to Output in High Z TCHZ* - 30 - 35 nS Output Disable to Output in High Z TOHZ* - 30 - 35 nS Output Hold from Address Change TOH 10 - 15 - nS These parameters are sampled but not 100% tested Write Cycle PARAMETER SYM. 5V 3V UNIT MIN. MAX. MIN. MAX. Write Cycle Time TWC 70 - 100 - nS Chip Selection to End of Write TCW 50 - 70 - nS Address Valid to End of Write TAW 50 - 70 - nS Address Setup Time TAS 0 - 0 - nS Write Pulse Width TWP 50 - 70 - nS TWR 0 - 0 - nS Data Valid to End of Write TDW 30 - 50 - nS Data Hold from End of Write TDH 0 - 0 - nS Write to Output in High Z TWHZ* - 25 - 30 nS Output Disable to Output in High Z TOHZ* - 25 - 30 nS Output Active from End of Write TOW 5 - 10 - nS Write Recovery Time CS1 , CS2, WE These parameters are sampled but not 100% tested -4- W24010 TIMING WAVEFORMS Read Cycle 1 (Address Controlled) TRC Address TOH TAA TOH DOUT Read Cycle 2 (Chip Select Controlled) CS1 CS2 TACS TCHZ TCLZ DOUT Read Cycle 3 (Output Enable Controlled) TRC Address TAA OE TOH TAOE TOLZ CS1 CS2 TACS DOUT TCHZ TOHZ TCLZ -5- Publication Release Date: November 1998 Revision A6 W24010 Timing Waveforms, continued Write Cycle 1 TWC Address TWR OE TCW CS1 CS2 TAW WE TWP TAS TOHZ (1, 4) DOUT TDW TDH DIN Write Cycle 2 ( OE = VIL Fixed) T WC Address TWR TCW CS1 CS2 TAW WE T WP TAS TOH TWHZ (1, 4) D OUT TDW (2) (3) TOW TDH DIN Notes: 1. During this period, I/O pins are in the output state, so input signals of opposite phase to the outputs should not be applied. 2. The data output from DOUT are the same as the data written to DIN during the write cycle. 3. DOUT provides the read data for the next address. 4. Transition is measured 500 mV from steady state with CL = 5 pF. This parameter is guaranteed but not 100% tested. -6- W24010 DATA RETENTION CHARACTERISTICS (TA (C) =-20 to 85 for LE; -40 to 85 for LI) PARAMETER VDD for Data Retention SYM. TEST CONDITIONS MIN. CS1 VDD -0.2V or VDR TYP. MAX. UNIT 2.0 - - V CS2 0.2V Data Retention Current IDDDR CS1 VDD -0.2V or CS2 0.2V, VDD = 3V - - 5 A Chip Deselect to Data Retention Time TCDR See data retention waveform 0 - - nS Operation Recovery Time TR TRC* - - nS * Read Cycle Time DATA RETENTION WAVEFORM VDD 0.9 x VDD VDR > = 1.5V TCDR CS1 CS2 0.9 x V DD TR CS1 > = V DD - 0.2V < CS2 < 0V = = 0.2V V -7- Publication Release Date: November 1998 Revision A6 W24010 ORDERING INFORMATION PART NO. PACKAGE ACCESS TIME (nS) OPERATING VOLTAGE (V) OPERATING TEMPERATURE (C) W24010-70LE 70/100 5V/3V -20 to 85 600 mil DIP W24010S-70LE 70/100 5V/3V -20 to 85 450 mil SOP W24010T-70LE 70/100 5V/3V -20 to 85 Standard type one TSOP W24010Q-70LE 70/100 5V/3V -20 to 85 Small type one TSOP W24010-70LI 70/100 5V/3V -40 to 85 600 mil DIP W24010S-70LI 70/100 5V/3V -40 to 85 450 mil SOP W24010T-70LI 70/100 5V/3V -40 to 85 Standard type one TSOP W24010Q-70LI 70/100 5V/3V -40 to 85 Small type one TSOP Notes: 1. Winbond reserves the right to make changes to its products without prior notice. 2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications where personal injury might occur as a consequence of product failure. -8- W24010 PACKAGE DIMENSIONS 32-pin P-DIP Dimension in inches Symbol A A1 A2 B B1 c D E E1 e1 L D 17 32 E1 16 1 E S c A A2 A1 L Base Plane Seating Plane B e1 eA a B1 Dimension in mm Min. Nom. Max. Min. Nom. Max. 5.33 0.210 0.010 0.25 0.150 0.155 0.160 3.81 3.94 4.06 0.016 0.018 0.022 0.41 0.46 0.56 0.048 0.050 0.054 1.22 1.27 1.37 0.008 0.010 0.014 0.20 0.25 1.650 1.660 0.36 41.91 42.16 0.610 14.99 15.24 15.49 0.545 0.550 0.555 13.84 13.97 14.10 0.090 0.100 0.110 2.29 2.54 2.79 0.120 0.130 0.140 3.05 3.30 3.56 15 0 0.670 16.00 16.51 17.02 0.590 a 0 eA S Notes: 0.630 0.600 0.650 15 0.085 2.16 1. Dimensions D Max. & S include mold flash or tie bar burrs. 2. Dimension E1 does not include interlead flash. 3. Dimensions D & E1 include mold mismatch and are determined at the mold parting line. 4. Dimension B1 does not include dambar protrusion/intrusion. 5. Controlling dimension: Inches 6. General appearance spec. should be based on final visual inspection spec. 32-pin SOP Wide Body Symbol A A1 A2 b c D E e HE L LE S y 17 32 e1 E HE L Detail F 1 b 16 Dimension in Inches Min. Nom. Max. Dimension in mm Min. Nom. 0.004 Max. 3.00 0.118 0.10 0.101 0.106 0.111 2.57 2.69 0.014 0.016 0.020 0.36 0.41 0.51 0.006 0.008 0.012 0.15 0.20 0.31 0.805 0.817 0.440 0.445 0.450 11.18 2.82 20.45 20.75 11.30 11.43 0.044 0.050 0.056 1.12 1.27 1.42 0.546 0.556 0.556 13.87 14.12 14.38 0.023 0.031 0.039 0.58 0.79 0.99 0.047 0.055 0.063 1.19 1.40 1.60 0 0.036 0.91 0.004 0.10 10 0 10 Notes: e1 D c A2 S y A e LE A1 1. Dimensions D Max. & S include mold flash or tie bar burrs. 2. Dimension b does not include dambar protrusion/intrusion. 3. Dimensions D & E include mold mismatch . mold parting line. and determined at the 4. Controlling dimension: Inches 5. General appearance spec should be based on final visual inspection spec. See Detail F Seating Plane -9- Publication Release Date: November 1998 Revision A6 W24010 Package Dimensions, continued 32-pin Standard Type One TSOP HD Dimension in Inches Dimension in mm Symbol D Nom. __ __ A c A1 1 M Min. Nom. __ __ __ 0.002 0.006 0.05 Max. 1.20 __ 0.15 0.037 0.039 0.041 0.95 1.00 1.05 b 0.007 0.008 0.009 0.17 0.20 0.23 c 0.005 0.006 0.007 0.12 0.15 0.17 D 0.720 0.724 0.728 18.30 18.40 18.50 E 0.311 0.315 0.319 7.90 8.00 8.10 HD 0.780 0.787 0.795 19.80 20.00 20.20 __ __ 0.024 0.40 __ __ E 0.10(0.004) b __ e L A 0.020 0.016 0.020 __ L1 L Min. 0.047 A2 e Max. 0.031 A2 Y 0.000 A1 1 __ 0.004 0.00 5 1 3 0.50 0.50 0.80 __ 3 Y L1 Controlling dimension: Millimeters 32-pin Small Type One TSOP HD Dimension in Inches Dimension in mm Min. Min. Symbol D A c 1 e E b A 2 A A1 L Y L1 Nom. Max. 0.049 Max. 1.25 A1 0.002 0.006 0.05 A2 b c 0.037 0.039 0.041 0.95 1.00 1.05 0.007 0.008 0.009 0.17 0.20 0.27 0.0056 0.0059 0.0062 0.14 0.15 0.16 0.15 D E HD e 0.461 0.465 0.469 11.70 11.80 11.90 L 0.012 0.020 0.028 L1 0.027 Y 0.000 0.311 0.315 0.319 7.90 8.00 8.10 0.520 0.528 0.536 13.20 13.40 13.60 0.020 0 0.50 0.30 0.50 0.70 0.675 0.004 3 5 0.00 0 Controlling dimension: Millimeters - 10 - Nom. 0.10 3 5 __ 0.60 __ 0.10 5 W24010 VERSION HISTORY VERSION DATE PAGE DESCRIPTION A1 Jun. 1996 - Initial Issued A2 Dec. 1996 - NA A3 Feb. 1998 1, 2, 4, 7, 8 A4 Apr. 1998 3 A5 Jun. 1998 2, 3 Delete operating temperature (SL = 0 to 70 C) Add standby power supply current (ISB1) typical parameter when operation temperature TA = 25 C Correct Operating Characteristics: add CS1, CS2 test conditions 7 Correct data retention characteristics: add CS1, CS2 test conditions A6 Nov. 1998 Headquarters 1, 8, 10, 11 Deduct reverse type one TSOP package Winbond Electronics (H.K.) Ltd. Rm. 803, World Trade Square, Tower II, No. 4, Creation Rd. III, 123 Hoi Bun Rd., Kwun Tong, Science-Based Industrial Park, Kowloon, Hong Kong Hsinchu, Taiwan TEL: 852-27513100 TEL: 886-3-5770066 FAX: 852-27552064 FAX: 886-3-5796096 http://www.winbond.com.tw/ Voice & Fax-on-demand: 886-2-27197006 Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408-9436666 FAX: 408-5441798 Taipei Office 11F, No. 115, Sec. 3, Min-Sheng East Rd., Taipei, Taiwan TEL: 886-2-27190505 FAX: 886-2-27197502 Note: All data and specifications are subject to change without notice. - 11 - Publication Release Date: November 1998 Revision A6