W24010
128K × 8 CMOS STATIC RAM
Publication Release Date: November 1998
- 1 - Revision A6
GENERAL DESCRIPTION
The W24010 is a normal-speed, very low-power CMOS static RAM organized as 131072 × 8 bits that
operates on a wide voltage range from 2.7V to 5.5V power supply. The W24010 family, W24010-
70LE and W24010-70LI, can meet the requirement of various operating temperature. This device is
manufactured using Winbond's high performance CMOS technology.
FEATURES
Low power consumption:
Active: 350 mW (max.)
Standby: 15 µW (max.) /3V
50 µW (max.) /5V
Access time: 70 nS (max.) /5V
100 nS (max.) /3V
Single 3V/5V power supply
Fully static operation
All inputs and outputs directly TTL compatible
Three-state outputs
Battery back-up operation capability
Data retention voltage: 2V (min.)
Packaged in 32-pin 600 mil DIP, 450 mil SOP,
standard type one TSOP (8 mm × 20 mm) and
small type one TSOP (8 mm × 13.4 mm)
PIN CONFIGURATIONS BLOCK DIAGRAM
V
A8
A9
WE
1
2
3
4
5
24
25
26
27
28
NC
A7
A6
A5
A12
A4
A3
A2
A1
6
7
8
9
20
21
22
23
A11
OE
A10
CS1
I/O8
I/O7
I/O6
I/O5
10
11
12
13
16 17
18
19
A0
I/O2
I/O3
I/O1
14
15
I/O4
A13
V
A14
A16
32
31
30
29
A15
CS2
DD
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A3
A2
A1
A0
OE
A10
CS1
I/O7
I/O6
I/O5
I/O4
32-pin
TSOP
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
I/O8
A15
A12
A7
A6
A5
A4
CS2
WE
A13
A8
DD
A11
A9
NC
A14
A16 VSS
I/O3
I/O2
I/O1
CORE CELL ARRAY
1024 ROWS
128 X 8 COLUMNS
DATA
CNTRL.
CLK
GEN.
R
O
W
D
E
C
O
D
E
R
A15
I/O CKT.
COLUMN DECODER
WE
OE
CLK GEN. PRECHARGE CKT.
A13 A8 A1A0 A11A10
CS1
CS2
A16
A14
A12
A4
A3
A2
A7
A6
A5
A9
I/O1
I/O8
:
PIN DESCRIPTION
SYMBOL DESCRIPTION
A0A16 Address Inputs
I/O1I/O8 Data Inputs/Outputs
CS1
, CS2 Chip Select Input
WE
Write Enable Input
OE
Output Enable Input
VDD Power Supply
VSS Ground
NC No Connection
W24010
- 2 -
TRUTH TABLE
CS
1
CS2
OE
WE
MODE I/O1
I/O8 VDD CURRENT
HXXX Not Selected High Z ISB, ISB1
XLX X Not Selected High Z ISB, ISB1
LHHH Output Disable High Z IDD
LHLHRead Data Out IDD
LHXLWrite Data In IDD
DC CHARACTERISTICS
Absolute Maximum Ratings
PARAMETER RATING UNIT
Supply Voltage to VSS Potential -0.5 to +7.0 V
Input/Output to VSS Potential -0.5 to VDD +0.5 V
Allowable Power Dissipation 1.0 W
Storage Temperature -65 to +150 °C
Operating Temperature LE -20 to 85 °C
LI -40 to 85 °C
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the
device.
Operating Characteristics
(VDD = 5V ±10%; VDD = 3V ±10%; VSS = 0V; TA (°C) =-20 to 85 for LE, -40 to 85 for LI)
PARAMETER SYM. TEST CONDITIONS 5V 3V UNIT
MIN. TYP.* MAX. MIN. TYP.* MAX.
Input Low Voltage VIL --0.5 -+0.8 -0.5 -+0.6 V
Input High Voltage VIH -+2.2 -VDD
+0.5 +2.0 -VDD
+0.5 V
Input Leakage
Current ILI VIN = VSS to VDD -1 -+1 -1 -+1 µA
Output Leakage
Current ILO VI/O = VSS to VDD,
CS1 = VIH (min.)
or CS2 = VIL (max.)
or OE = VIH (min.)
or WE = VIL (max.)
-1 -+1 -1 -+1 µA
Output Low Voltage VOL IOL = +2.1 mA - - 0.4 - - 0.4 V
Output High
Voltage VOH IOH = -1.0 mA 2.4 - - 2.2 - - V
W24010
Publication Release Date: November 1998
- 3 - Revision A6
Operating Characteristics, continued
PARAMETER SYM. TEST CONDITIONS 5V 3V UNIT
MIN. TYP.* MAX. MIN. TYP.* MAX.
Operating Power
Supply Current IDD CS1 = VIL (max.)
and CS2 = VIH (min.)
I/O = 0 mA
Cycle = min.
Duty = 100%
- - 70 - - 30 mA
Standby Power
Supply Current ISB CS1 = VIH (min.) or
CS2 = VIL (max.)
Cycle = min.
Duty = 100%
- - 3- - 1mA
ISB1CS1 VDD -0.2V or
CS2 0.2V -1.0 10 -0.5 5µA
Note: Typical parameter is measured under ambient temperature TA = 25° C and VDD = 5V/ 3V
CAPACITANCE
(VDD = 5 V, TA = 25° C, f = 1 MHz)
PARAMETER SYM. CONDITIONS MAX. UNIT
Input Capacitance CIN VIN = 0V 6pF
Input/Output Capacitance CI/O VOUT = 0V 8pF
Note: These parameters are sampled but not 100% tested.
AC Characteristics
AC Test Conditions
PARAMETER CONDITIONS
Input Pulse Levels 3V 0V to 2.4V
5V 0V to 3.0V
Input Rise and Fall Times 5 nS
Input and Output Timing Reference Level 1.5V
Output Load See the drawing below
AC Test Loads and Waveform
90% 90%
5 nS
10%
5 nS 10%
OUTPUT OUTPUT
2.4 V / 3.0 V
0 V
100 pF
Including
Jig and
Scope
5 pF
Including
Jig and
Scope
1 TTL 1 TTL
CLZ, OLZ, CHZ, OHZ, WHZ, OW(For T T T T T T )
W24010
- 4 -
AC Characteristics, continued
(VDD = 5 V ±10%; VDD = 3 V ±10%; VSS = 0 V; TA (°C) =-20 to 85 for LE, -40 to 85 for LI)
Read Cycle
PARAMETER SYM. 5 V 3 V UNIT
MIN. MAX. MIN. MAX.
Read Cycle Time TRC 70 -100 -nS
Address Access Time TAA -70 -100 nS
Chip Select Access Time TACS -70 -100 nS
Output Enable to Output Valid TAOE -35 -50 nS
Chip Selection to Output in Low Z TCLZ*10 -15 -nS
Output Enable to Output in Low Z TOLZ*5-5-nS
Chip Deselection to Output in High Z TCHZ*-30 -35 nS
Output Disable to Output in High Z TOHZ*-30 -35 nS
Output Hold from Address Change TOH 10 -15 -nS
These parameters are sampled but not 100% tested
Write Cycle
PARAMETER SYM. 5 V 3 V UNIT
MIN. MAX. MIN. MAX.
Write Cycle Time TWC 70 -100 -nS
Chip Selection to End of Write TCW 50 -70 -nS
Address Valid to End of Write TAW 50 -70 -nS
Address Setup Time TAS 0-0-nS
Write Pulse Width TWP 50 -70 -nS
Write Recovery Time
CS1
, CS2,
WE
TWR 0-0-nS
Data Valid to End of Write TDW 30 -50 -nS
Data Hold from End of Write TDH 0-0-nS
Write to Output in High Z TWHZ*-25 -30 nS
Output Disable to Output in High Z TOHZ*-25 -30 nS
Output Active from End of Write TOW 5-10 -nS
These parameters are sampled but not 100% tested
W24010
Publication Release Date: November 1998
- 5 - Revision A6
TIMING WAVEFORMS
Read Cycle 1
(Address Controlled)
Address
TRC
TAA
TOH TOH
DOUT
Read Cycle 2
(Chip Select Controlled)
DOUT
CS1
TCLZ
TACS CHZ
T
CS2
Read Cycle 3
(Output Enable Controlled)
Address
TRC
CS1
TAA
OE
TAOE
TOLZ
TOH
TACS
DOUT CLZ
TCHZ
TTOHZ
CS2
W24010
- 6 -
Timing Waveforms, continued
Write Cycle 1
Address
OE
TWC
TWR
WE
DOUT
DIN
TWP
TAS
TOHZ (1, 4)
TDW TDH
TAW
CS1 TCW
CS2
Write Cycle 2
(
OE
= VIL Fixed)
WE
DOUT
DIN
TAS
TDH
TWP
TWHZ
DW
T
(2) (3)
TOW
TOH
AW
T
(1, 4)
TCW TWR
Address
TWC
CS1
CS2
Notes:
1. During this period, I/O pins are in the output state, so input signals of opposite phase to the outputs should not be applied.
2. The data output from DOUT are the same as the data written to DIN during the write cycle.
3. DOUT provides the read data for the next address.
4. Transition is measured ±500 mV from steady state with CL = 5 pF. This parameter is guaranteed but not 100% tested.
W24010
Publication Release Date: November 1998
- 7 - Revision A6
DATA RETENTION CHARACTERISTICS
(TA (°C) =-20 to 85 for LE; -40 to 85 for LI)
PARAMETER SYM. TEST CONDITIONS MIN. TYP. MAX. UNIT
VDD for Data Retention VDR CS1 VDD -0.2V or
CS2 0.2V
2.0 - - V
Data Retention Current IDDDR CS1 VDD -0.2V or
CS2 0.2V, VDD = 3V - - 5µA
Chip Deselect to Data
Retention Time TCDR See data retention waveform 0- - nS
Operation Recovery Time TRTRC*- - nS
* Read Cycle Time
DATA RETENTION WAVEFORM
TCDR
-0.2V
DD
V
VDD
CS1
TR
CS1
VDR 1.5V
=
>
=
>
0.9 x DD
V
CS2
0.9 x DD
V
0.2V
CS2
V
0V =
<=
<
W24010
- 8 -
ORDERING INFORMATION
PART NO. ACCESS
TIME (nS) OPERATING
VOLTAGE (V)OPERATING
TEMPERATURE
(
°
C)
PACKAGE
W24010-70LE 70/100 5V/3V -20 to 85 600 mil DIP
W24010S-70LE 70/100 5V/3V -20 to 85 450 mil SOP
W24010T-70LE 70/100 5V/3V -20 to 85 Standard type one
TSOP
W24010Q-70LE 70/100 5V/3V -20 to 85 Small type one TSOP
W24010-70LI 70/100 5V/3V -40 to 85 600 mil DIP
W24010S-70LI 70/100 5V/3V -40 to 85 450 mil SOP
W24010T-70LI 70/100 5V/3V -40 to 85 Standard type one
TSOP
W24010Q-70LI 70/100 5V/3V -40 to 85 Small type one TSOP
Notes:
1. Winbond reserves the right to make changes to its products without prior notice.
2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications
where personal injury might occur as a consequence of product failure.
W24010
Publication Release Date: November 1998
- 9 - Revision A6
PACKAGE DIMENSIONS
32-pin P-DIP
1. Dimensions D Max. & S include mold flash or
tie bar burrs.
2. Dimension E1 does not include interlead flash.
3. Dimensions D & E1 include mold mismatch and
are determined at the mold parting line.
6. General appearance spec. should be based on
final visual inspection spec.
1.371.22
0.0540.048
Notes:
Symbol Min. Nom. Max. Max.
Nom.
Min.
Dimension in inches Dimension in mm
A
B
c
D
e
A
L
S
A
A1
2
E
0.050 1.27
0.210 5.33
0.010
0.150
0.016
0.155
0.018
0.160
0.022
3.81
0.41
0.25
3.94
0.46
4.06
0.56
0.008
0.120
0.670
0.010
0.130
0.014
0.140
0.20
3.05
0.25
3.30
0.36
3.56
0.555
0.550
0.545 14.10
13.9713.84
17.02
15.24
14.99 15.49
0.6000.590 0.610
2.29 2.54 2.790.090 0.100 0.110
B1
1
e
E1
a
1.650 1.660 41.91 42.16
0 15
0.085 2.16
0.650
0.630 16.00 16.51
protrusion/intrusion.
4. Dimension B1 does not include dambar
5. Controlling dimension: Inches
150
Seating Plane
eA
2A
a
c
E
Base Plane
1A
1
e
L
A
S
1E
D
1
B
B
32
116
17
32-pin SOP Wide Body
1
17
32
16
ye
D
S
Seating Plane
b
A
A
EH
L
L
E
E
1
c
e1
1
e
A2
See Detail F
Detail F
1. Dimensions D Max. & S include mold flash
or tie bar burrs.
2. Dimension b does not include dambar
protrusion/intrusion.
3. Dimensions D & E include mold mismatch
and determined at the mold parting line.
.
Notes:
4. Controlling dimension: Inches
5. General appearance spec should be based
on final visual inspection spec.
0.200.15
0.0080.006
Symbol Min. Nom. Max. Max.Nom.Min.
Dimension in Inches Dimension in mm
A
b
c
D
e
HE
L
y
A
A
LE
1
2
E
0.012 0.31
0.118 3.00
0.004
0.101
0.014
0.106
0.016
0.111
0.020
2.57
0.36
0.10
2.69
0.41
2.82
0.51
0.047
0.004
010
0.805
0.055
0.817
0.063 1.19
20.45
1.40
20.75
1.60
0.556
0.5560.546 14.3814.1213.87
10
0
0.10
11.43
11.30
11.18
0.4500.445
0.440
0.58 0.79 0.990.023 0.031 0.039
1.12 1.27 1.420.044 0.050 0.056
S0.91
0.036
θ
θ
W24010
- 10 -
Package Dimensions, continued
32-pin Standard Type One TSOP
A
A
A
2
1
L
L1Y
c
E
H
D
D
b
e
M
0.10(0.004)
θ
Min. Nom. Max. Min. Nom. Max.
Symbol
A
A
b
c
D
E
e
L
L
Y
1
1
2
A
HD
Controlling dimension: Millimeters
Dimension in Inches
0.047
0.006
0.041
0.039
0.037
0.007 0.008 0.009
0.005 0.006 0.007
0.720 0.724 0.728
0.311 0.315 0.319
0.780 0.787 0.795
0.020
0.016 0.020 0.024
0.031
0.000 0.004
135
0.002
1.20
0.05 0.15
1.051.00
0.95
0.17
0.12
18.30
7.90
19.80
0.40
0.00
1
0.20 0.23
0.15 0.17
18.40 18.50
8.00 8.10
20.00 20.20
0.50
0.50 0.60
0.80
0.10
35
Dimension in mm
θ
__ __ __ __
__ __
__ __
__ __
__
__
__
__
__
__
1
32-pin Small Type One TSOP
A
AA
2
1
L
L1Y
c
E
H
D
D
b
e
1
Controlling dimension: Millimeters
Min.
Dimension in mm
Nom. Max. Min. Nom. Max.
Symbol
A
A
b
c
D
E
e
L
L
Y
1
1
2
A
HD
11.70
13.20
0.675
1.25
0.05 0.15
1.051.00
0.95
0.17
0.14
0.30
0.00
0.20 0.27
0.15 0.16
11.80 11.90
13.40 13.60
0.50
0.50 0.70
0.10
0.049
0.006
0.041
0.039
0.037
0.007 0.008 0.009
0.00560.0059 0.0062
0.461 0.465 0.469
7.90 8.00 8.100.311 0.315 0.319
0.520 0.528 0.536
0.020
0.012 0.020 0.028
0.027
0.000 0.004
0.002
0 3 50 3 5
θ
Dimension in Inches
θ
W24010
Publication Release Date: November 1998
- 11 - Revision A6
VERSION HISTORY
VERSION DATE PAGE DESCRIPTION
A1 Jun. 1996 -Initial Issued
A2 Dec. 1996 -NA
A3 Feb. 1998 1, 2, 4, 7, 8 Delete operating temperature (SL = 0 to 70 °C)
A4 Apr. 1998 3Add standby power supply current (ISB1) typical
parameter when operation temperature TA = 25° C
A5 Jun. 1998 2, 3 Correct Operating Characteristics:
add CS1, CS2 test conditions
7Correct data retention characteristics:
add CS1, CS2 test conditions
A6 Nov. 1998 1, 8, 10, 11 Deduct reverse type one TSOP package
Headquarters
No. 4, Creation Rd. III,
Science-Based Industrial Park,
Hsinchu, Taiwan
TEL: 886-3-5770066
FAX: 886-3-5796096
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-27197006
Taipei Office
11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-27190505
FAX: 886-2-27197502
Winbond Electronics (H.K.) Ltd.
Rm. 803, World Trade Square, Tower II,
123 Hoi Bun Rd., Kwun Tong,
Kowloon, Hong Kong
TEL: 852-27513100
FAX: 852-27552064
Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.
2727 N. First Street, San Jose,
CA 95134, U.S.A.
TEL: 408-9436666
FAX: 408-5441798
Note: All data and specifications are subject to change without notice.