Date Revision
This specification sheet forms a part of the latest issue of Raychem Specification 55A.
TITLE
SPECIFICATION CONTROL DRAWING
ONE CONDUCTOR CABLE, SPIRALLY SHIELDED, JACKETED
COMPONENT WIRE - EPD6062-AWG-CO1
EPD6062
SHIELD - SPIRAL, TIN-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED ETFE
NOMINAL MAXIMUM
SHIELD
SIZE
(AWG)
PART NUMBER
1/
OUTSIDE DIAMETER
(inch)
MINIMUM
JACKET
THICKNESS
(inch)
.007
.007
.007
.013
EPD6062-16-*
EPD6062-14-*
EPD6062-12-*
EPD6062-10-*
CONDUCTOR
SIZE
(AWG)
MAXIMUM
WEIGHT
(lb/1000 ft)
CABLE CONSTRUCTION DETAILS
16
14
12
10
38
38
38
38
15.42
21.30
30.20
47.29
.111
.123
.147
.185
.104
.118
.140
.177
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 7 hours
BLOCKING: 200 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
FLAMMABILITY: Procedure 1,
3 seconds (maximum); 3 in. (maximum);
no flaming of facial tissue
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LIFE CYCLE: 200 ± 3°C for 168 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 90% (minimum)
VOLTAGE WITHSTAND TEST (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The "*" in the part numbers above shall be replaced by a color
code designator with a dash separating the component wire
color from the jacket color.
1/ Example: AWG 16, white component wire; white jacket:
EPD6062-16-9-9
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
NOTE: Nominal values are for information only.
Nominal values are not requirements.
7-29-04 C
Review
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
Page 1 of 1 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
R Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
