SCOPE This specification applies to the current type Radial Leaded Inductor for MCD-1216-SERIES PRODUCT INDENTIFICATION MCD - 1216 - 150 M Product Code Dimensions Code Inductance Code Tolerance Code (1) SHAPES AND DIMENSIONS A: 15.0 Max. mm B: 16.5 Max. mm C: 15.02.0 mm D: 7.50.5 mm E: 0.80.1 mm F: 2.5 Max. mm (2) ELECTRICAL SPECIFICATIONS SEE TABLE 1 TEST INSTRUMENTS L : HP 4284A PRECISION LCR METER (or equivalent) RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent) (3) CHARACTERISTICS (3)-1 Ambient temperature ............... 60 Max. (3)-2 Operate temperature range ...... 40125 (Including self temp. rise) (3)-3 Storage temperature range ...... 40125 MAG.LAYERS MCD-1216-SERIES Page 1/4 TABLE 1 MAGLAYERS Inductance Percent Test Resistance PT/NO. L(H) Tolerance Frequency RDC()Max. IDC1(A) IDC2(A) MCD-1216-100 10 K,M 100kHz/0.25V 19m 10.0 6.80 MCD-1216-120 12 K,M 100kHz/0.25V 23m 8.8 6.40 MCD-1216-150 15 M 100kHz/0.25V 27m 8.5 5.90 MCD-1216-220 22 M 100kHz/0.25V 29m 7.0 5.40 MCD-1216-101 100 K,M 100kHz/0.25V 0.15 2.4 3.20 MCD-1216-221 220 K,M 100kHz/0.25V 0.31 1.60 2.15 MCD-1216-271 270 K,M 100kHz/0.25V 0.40 1.45 2.00 MCD-1216-331 330 K,M 100kHz/0.25V 0.46 1.30 1.75 MCD-1216-391 390 K,M 100kHz/0.25V 0.58 1.15 1.70 MCD-1216-471 470 K,M 100kHz/0.25V 0.70 1.00 1.50 MCD-1216-561 560 K,M 100kHz/0.25V 0.75 0.95 1.35 MCD-1216-681 680 K,M 100kHz/0.25V 0.80 0.90 1.30 MCD-1216-821 820 K,M 100kHz/0.25V 0.85 0.80 1.10 MCD-1216-102 1000 K,M 100kHz/0.25V 0.90 0.75 1.00 MCD-1216-302 3000 K,M 10kHz/0.25V 2.79 0.53 0.60 MCD-1216-332 3300 K,M 10kHz/0.25V 2.89 0.52 0.55 MCD-1216-402 4000 K,M 10kHz/0.25V 3.73 0.49 0.50 Rated DC Current Specify the inductance tolerance,K(10%), M(20%) IDC1Based on inductance change (L/Lodrop 10% Max) @ ambient temp. 25 IDC2Based on temperature rise (T 40 TYP.) Rated DC Current The less value which is IDC1 or IDC2. MAG.LAYERS MCD-1216-SERIES Page-2/4 (4) RELIABILITY TEST METHOD MECHANICAL NO. ITEMS CONDITIONS SPECIFICATIONS 1 Solderability test More than 90% of the Dipping: 245 5 , 3 1 seconds termnial electrode should be covered with solder. 2 lead tensile 1.0 Kg MIN. The lead of product is pulled with a load of strength test 1.0kg mininum until lead breakdown. The tensile force shall be recorded. 3 Vibration test L/L7% The product is fixed ento the vibration with Visual:OK amplitude of 1.52m/m at a frequency of 1055Hz sweeping for lmin. The vibration is done at X,Y, Z direction respectively for 2 houes, totally 6 hours. 4 Soldering heat Visual:OK The leads of product are dipped into a solder pot resistance test Circuit:OK of 2605 for a duration of 101sec. Nothing particular on visual and open circuitry as a result of ore testing. ENVIRONMENTAL NO. 1 2 ITEMS Humidity SPECIFICATIONS L/L5% CONDITIONS The product is placed in a chamber of 402, endurance 9095%RH for 96 hours. Measurement is done test after the reaovery of 424 hours. High temp L/L5% The product is placed in a chamber of 802, for 72 hours. Measurement is done after recovery endurance test of 424 hours. 3 Low temp test L/L5% The product is placed in a chamber of -402, for 96 hours. Measurement is done after recovery of 424 hours. 4 Thermal shock L/L5% test The specimens are placed in a chamber and the temp is then lowered to -202 for one hour. The temp will raised to +802 for one hour. This constitues one cycle. Ten cycles of such testing shall be completed. Measurement is made after recovery for 424 hours from the completion of testing. M AG .LAYER S MCD-1216-SERIES Page-3/4 (5) PACKAGE SPECIFICATION (mm) M AG.LAYER S MCD-1216-SERIES Page-4/4