LM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM101A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA N DIP8 (Plastic Package) SLEW RATE AS INVERSING10V/s 10V/s AMPLIFIER DESCRIPTION The LM101A is a general purpose operational amplifier which offers many features: supply voltages from 5V to 22V, low current drain, overload protection on the input and output, no latch-up when the common-mode range is exceeded, free from oscillations and compensation with a single 30pF capacitor. It has advantages over internally compensated amplifiers in that the compensation can be tailored to the particular application: slew rate of 10V/s and bandwidth of 3.5MHz can be easily achieved. D SO8 (Plastic Micropackage) PIN CONNECTIONS (top view) ORDER CODE Package Part Number Temperature Range LM101A -55C, +125C LM201A -40C, +105C LM301A 0C, +70C Example : LM201AN N D * * * * * * N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) December 2001 1234- 1 8 2 7 3 6 4 5 Balance, compensation Inverting input Non-inverting input VCC- 5 - Balance 6 - Output 7 - VCC+ 8 - Compensation 2 1/11 LM101A - LM201A - LM301A SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter LM101A LM201A LM301A Unit Supply voltage 22 V Vi Input Voltage 15 V Vid Differential Input Voltage 30 V Ptot Power Dissipation N Suffix D Suffix 500 300 Infinite Output Short-circuit Duration Toper Opearting Free-air Temperature Range Tstg Storage Temperature Range 2/11 -55 to +125 -40 to +105 -65 to +150 mW 0 to +70 C C LM101A - LM201A - LM301A ELECTRICAL CHARACTERISTICS 5V VCC 20V, C1 = 30pF, Tamb = 25C (unless otherwise specified) LM101A - LM201A Symbol Unit Min. Vio DVio LM301A Parameter Input Offset Voltage (RS 10k) Tamb = +25C Tmin Tamb Tmax Input Offset Voltage Drift Tmin Tamb Tmax Typ. Max. 0.7 Min. Typ. Max. 2 3 2 7.5 10 3 15 6 30 mV V/C Iib Input Bias Current - note Tamb = +25C Tmin Tamb Tmax 25 75 100 70 250 300 nA Iio Input Offset Current Tamb = +25C Tmin Tamb Tmax 1.5 10 20 2 50 70 nA 10 20 100 200 10 20 300 600 pA/C DIIio Input Offset Current Drift Tmin Tamb 25C Tmin Tamb Tmax Avd Large Signal Voltage Gain * VO 10V, RL = 2k) Tamb = +25C Tmin Tamb Tmax 50 25 100 25 15 100 SVR Supply Voltage Rejection Ratio (Rs 10k) Tamb = +25C Tmin Tamb Tmax 80 80 96 70 70 96 ICC Supply Current, no load Tamb = +25C Tmin Tamb Tmax Vicm Input Common Mode Voltage Range (VCC = 20V) Tamb = +25C Tmin Tamb Tmax CMR Common Mode Rejection Ratio (Rs 10k) Tamb = +25C Tmin Tamb Tmax 80 80 96 Output Short-circuit Current * Tamb = +25C 10 30 12 10 12 10 0.25 IOS Output Voltage Swing * Tamb = +25C VOPP SR Tmin Tamb Tmax 1.8 RL = RL = RL = RL = 3 3 15 15 10k 2k 10k 2k 1.8 dB 3 3 70 70 96 10 30 14 13 12 10 12 10 14 13 0.5 0.25 0.5 50 mA V 15 15 Slew Rate (Vi = 10V, RL = 2k,CL = 100pF, unity gain) - 1) V/mV dB 50 mA V V/s 3/11 LM101A - LM201A - LM301A LM101A - LM201A Symbol LM301A Parameter Unit Min. Typ. Max. Min. Typ. tr Rise (Vi = 20mV, RL = 2k,CL = 100pF, unity gain) 0.3 0.3 KOV Overshoot (Vi = 20mV, RL = 2k,CL = 100pF, unity gain) 5 5 Zi Input Impedance * 1.5 4 1.5 4 GBP Gain Bandwidth Product * (Vi = 10mV, RL = 2k,CL = 100pF, f = 100KHz) 0.5 1 0.5 1 THD Total Harmonic Distortion (f = 1kHz, Av = 20dB, RL = 2k, Vo = 2Vpp, CL = 100pF) en Equivalent Input Noise Voltage f = 1kHz, Rs = 100 1. May be improved up to 10V/s in inverting amplifier configuration * ==> VCC = 15V, T amb = +25C (unless otherwise specified) 4/11 0.015 0.015 25 25 Max. s % M MHz % nV -----------Hz LM101A - LM201A - LM301A 5/11 LM101A - LM201A - LM301A SINGLE POLE COMPENSATION 6/11 FEED FORWARD COMPENSATION LM101A - LM201A - LM301A 7/11 LM101A - LM201A - LM301A 8/11 LM101A - LM201A - LM301A 9/11 LM101A - LM201A - LM301A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dim. Min. A a1 B b b1 D E e e3 e4 F i L Z 10/11 Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 0.020 0.045 0.014 0.008 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Max. 0.131 1.65 0.55 0.304 10.92 9.75 7.95 Typ. 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 LM101A - LM201A - LM301A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) s b1 b a1 A a2 C c1 a3 L E e3 D M 5 1 4 F 8 Millimeters Inches Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45 (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 8 (max.) Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States (c) http://www.st.com 11/11