S-812C51AMC-C3FT2G - Seiko Semiconductors

S-812C Series

www.ablicinc.com

16 V INPUT, 75 mA

VOLTAGE REGULATOR

The S-812C Series is a high-withstand voltage regulator IC which is developed by using the CMOS technology.

This IC is suitable for applications which require withstand because its maximum voltage for operation is as high

as 16 V, also for portable device having the low current consumption because this IC not only has the low

current consumption but also a ON/OFF circuit. This IC operates stably due to the internal phase compensation

circuit so that users are able to use ceramic capacitor as the output capacitor.

 Features

 Output voltage: 2.0 V to 6.0 V, selectable in 0.1 V step

 Input voltage: 16 V max.

 Output voltage accuracy: 2.0%

 Dropout voltage: 120 mV typ. (5.0 V output product, IOUT = 10 mA)

 Current consumption: During operation: 1.0 A typ., 1.8 A max. (3.0 V output product)

 Output current: Possible to output 50 mA (3.0 V output product, VIN = 5 V)*1

Possible to output 75 mA (5.0 V output product, VIN = 7 V)*1

 Built-in ON/OFF circuit: Selectable available / unavailable of power-off function

Selectable active “H” / “L” in the regulator

 Built-in short-circuit protection circuit: Selectable available / unavailable of short-circuit protection circuit

Available short-circuit protection: Short-circuit current 40 mA typ.

 Operation temperature range: Ta = 40C to 85C

 Lead-free, Sn 100%, halogen-free*2

*1. Attention should be paid to the power dissipation of the package when the load is large.

*2. Refer to “ Product Name Structure” for details.

 Applications

 Constant-voltage power supply for home electric appliance

 Constant-voltage power supply for battery-powered device

 Constant-voltage power supply for communication device

 Packages

 SNT-6A(H)

 SOT-23-5

 SOT-89-3

 SOT-89-5

 TO-92

 WLP-4R

www.ablic.com

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Block Diagrams

1. S-812CxxA Series (Unavailable short-circuit protection and power-off function)





VSS

VOUT

VIN *1

Reference

voltage

*1. Parasitic diode

Figure 1

2. S-812CxxB Series (Available short-circuit protection and power-off function)

VSS

VOUT

ON/OFF

VIN

Short-circuit

protection

Reference

voltage





*1. Parasitic diode

Figure 2

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

3. S-812CxxE Series (Available Short-circuit protection function, unavailable power-off function)

VSS

VOUT

VIN *1

Reference

voltage

Short-circuit

protection





*1. Parasitic diode

Figure 3

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Product Name Structure

Users can select the product type, output voltage, and package type for the S-812C Series. Refer to “1.

Product name” regarding the contents of product name, “2. Packages” regarding the package drawings,

“3. Product name list” regarding details of product name.

1. Product name

1. 1 S-812CxxA series

1. 1. 1 SOT-23-5, SOT-89-3

S-812C xx A xx - xxx T2 x

Environmental code

U: Lead-free (Sn 100%), halogen-free

G: Lead-free (for details, please contact

our sales office)

IC direction in tape specifications*1

T2: SOT-23-5, SOT-89-3

Product code*2

Package code

MC: SOT-23-5

UA: SOT-89-3

Short-circuit protection and power-off function

A: Unavailable

Output voltage

20 to 60

(e.g. When the output voltage is 2.0 V,

it is expressed 20

)

*1. Refer to the tape drawing.

*2. Refer to “3. Product name list”.

1. 1. 2 TO-92

S-812C xx A Y - x 2 - U

Environmental code

U: Lead-free (Sn 100%), halogen-free

Packing from

B: Bulk

Z: Tape and ammo

Package code

Y: TO-92

Short-circuit protection and power-off function

A: Unavailable

Output voltage

20 to 60

(e.g. When the output voltage is 2.0 V,

it is expressed 20)

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

1. 2 S-812CxxB series

1. 2. 1 SNT-6A(H)

S-812C xx B PI - xxx TF U

Environmental code

U: Lead-free (Sn 100%), halogen-free

IC direction in tape specifications*1

TF: SNT-6A(H)

Product code*2

Package code

PI: SNT-6A(H)

Short-circuit protection and power-off function

B: Available

ON/OFF pin positive logic (operates by “H”)

Output voltage

20 to 60

(e.g. When the output voltage is 2.0V,

it is expressed 20)

*1. Refer to the tape drawing.

*2. Refer to “3. Product name list”.

1. 2. 2 SOT-23-5、SOT-89-5

S-812C xx B xx - xxx T2 x

Environmental code

U: Lead-free (Sn 100%), halogen-free

G: Lead-free (for details, please contact

our sales office)

IC direction in tape specifications*1

T2: SOT-23-5, SOT-89-5

Product code*2

Package code

MC: SOT-23-5

UC: SOT-89-5

Short-circuit protection and power-off function

B: Available

ON/OFF pin positive logic (operates by “H”)

Output voltage

20 to 60

(e.g. When the output voltage is 2.0V,

it is expressed 20)

*1. Refer to the tape drawing.

*2. Refer to “3. Product name list”.

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

1. 2. 3 WLP-4R

S-812C xx B - H4T1 S

Environmental code

S: Lead-free, halogen-free

Package code and packing specifications*1

H4T1: WLP-4R, Tape

Short-circuit protection and power-off function

B: Available

ON/OFF pin positive logic (operates by “H”)

Output voltage

20 to 60

(e.g. When the output voltage is 2.0V,

it is expressed 20)

*1. Refer to the tape drawing.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

1. 3 S-812CxxE series

S-812C xx E UA - xxx T2 x

Environmental code

U: Lead-free (Sn 100%), halogen-free

G: Lead-free (for details, please contact

our sales office)

IC direction in tape specifications*1

Product code*2

Package code

UA: SOT-89-3

Short-circuit protection function: Available

Power-off functio: Unavailable

Output voltage

20 to 60

(e.g. When the output voltage is 2.0 V,

it is expressed 20)

*1. Refer to the tape drawing.

*2. Refer to “3. Product name list”.

2. Packages

Package name Drawing code

Package Tape Reel Ammo packing Land

SNT-6A(H) PI006-A-P-SD PI006-A-C-SD PI006-A-R-SD  PI006-A-L-SD

SOT-23-5 MP005-A-P-SD

MP005-A-C-SD MP005-A-R-SD

 

SOT-89-3 UP003-A-P-SD UP003-A-C-SD UP003-A-R-SD  

SOT-89-5 UP005-A-P-SD UP005-A-C-SD UP005-A-R-SD  

TO-92 (Bulk) YS003-D-P-SD    

TO-92 (Tape and ammo)

YZ003-E-P-SD YZ003-E-C-SD YZ003-E-Z-SD 

WLP-4R

HR004-A-P-SD HR004-A-C-SD HR004-A-R-SD  

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

3. Product name list

3. 1 S-812CxxA Series (Unavailable short-circuit protection and power-off function)

Table 1

Output voltage SOT-23-5 SOT-89-3 SOT-89-5 TO-92*1

2.0 V2.0 % S-812C20AMC-C2AT2x S-812C20AUA-C2AT2x  S-812C20AY-n2-U

2.1 V2.0 % S-812C21AMC-C2BT2x S-812C21AUA-C2BT2x  S-812C21AY-n2-U

2.2 V2.0 % S-812C22AMC-C2CT2x S-812C22AUA-C2CT2x  S-812C22AY-n2-U

2.3 V2.0 % S-812C23AMC-C2DT2x S-812C23AUA-C2DT2x  S-812C23AY-n2-U

2.4 V2.0 % S-812C24AMC-C2ET2x S-812C24AUA-C2ET2x  S-812C24AY-n2-U

2.5 V2.0 % S-812C25AMC-C2FT2x S-812C25AUA-C2FT2x  S-812C25AY-n2-U

2.6 V2.0 % S-812C26AMC-C2GT2x S-812C26AUA-C2GT2x  S-812C26AY-n2-U

2.7 V2.0 % S-812C27AMC-C2HT2x S-812C27AUA-C2HT2x  S-812C27AY-n2-U

2.8 V2.0 % S-812C28AMC-C2IT2x S-812C28AUA-C2IT2x  S-812C28AY-n2-U

2.9 V2.0 % S-812C29AMC-C2JT2x S-812C29AUA-C2JT2x  S-812C29AY-n2-U

3.0 V2.0 % S-812C30AMC-C2KT2x S-812C30AUA-C2KT2x  S-812C30AY-n2-U

3.1 V2.0 % S-812C31AMC-C2LT2x S-812C31AUA-C2LT2x  S-812C31AY-n2-U

3.2 V2.0 % S-812C32AMC-C2MT2x S-812C32AUA-C2MT2x  S-812C32AY-n2-U

3.3 V2.0 % S-812C33AMC-C2NT2x S-812C33AUA-C2NT2x  S-812C33AY-n2-U

3.4 V2.0 % S-812C34AMC-C2OT2x S-812C34AUA-C2OT2x  S-812C34AY-n2-U

3.5 V2.0 % S-812C35AMC-C2PT2x S-812C35AUA-C2PT2x  S-812C35AY-n2-U

3.6 V2.0 % S-812C36AMC-C2QT2x S-812C36AUA-C2QT2x  S-812C36AY-n2-U

3.7 V2.0 % S-812C37AMC-C2RT2x S-812C37AUA-C2RT2x  S-812C37AY-n2-U

3.8 V2.0 % S-812C38AMC-C2ST2x S-812C38AUA-C2ST2x  S-812C38AY-n2-U

3.9 V2.0 % S-812C39AMC-C2TT2x S-812C39AUA-C2TT2x  S-812C39AY-n2-U

4.0 V2.0 % S-812C40AMC-C2UT2x S-812C40AUA-C2UT2x  S-812C40AY-n2-U

4.1 V2.0 % S-812C41AMC-C2VT2x S-812C41AUA-C2VT2x  S-812C41AY-n2-U

4.2 V2.0 % S-812C42AMC-C2WT2x S-812C42AUA-C2WT2x  S-812C42AY-n2-U

4.3 V2.0 % S-812C43AMC-C2XT2x S-812C43AUA-C2XT2x  S-812C43AY-n2-U

4.4 V2.0 % S-812C44AMC-C2YT2x S-812C44AUA-C2YT2x  S-812C44AY-n2-U

4.5 V2.0 % S-812C45AMC-C2ZT2x S-812C45AUA-C2ZT2x  S-812C45AY-n2-U

4.6 V2.0 % S-812C46AMC-C3AT2x S-812C46AUA-C3AT2x  S-812C46AY-n2-U

4.7 V2.0 % S-812C47AMC-C3BT2x S-812C47AUA-C3BT2x  S-812C47AY-n2-U

4.8 V2.0 % S-812C48AMC-C3CT2x S-812C48AUA-C3CT2x  S-812C48AY-n2-U

4.9 V2.0 % S-812C49AMC-C3DT2x S-812C49AUA-C3DT2x  S-812C49AY-n2-U

5.0 V2.0 % S-812C50AMC-C3ET2x S-812C50AUA-C3ET2x  S-812C50AY-n2-U

5.1 V2.0 % S-812C51AMC-C3FT2x S-812C51AUA-C3FT2x  S-812C51AY-n2-U

5.2 V2.0 % S-812C52AMC-C3GT2x S-812C52AUA-C3GT2x  S-812C52AY-n2-U

5.3 V2.0 % S-812C53AMC-C3HT2x S-812C53AUA-C3HT2x  S-812C53AY-n2-U

5.4 V2.0 % S-812C54AMC-C3IT2x S-812C54AUA-C3IT2x  S-812C54AY-n2-U

5.5 V2.0 % S-812C55AMC-C3JT2x S-812C55AUA-C3JT2x  S-812C55AY-n2-U

5.6 V2.0 % S-812C56AMC-C3KT2x S-812C56AUA-C3KT2x  S-812C56AY-n2-U

5.7 V2.0 % S-812C57AMC-C3LT2x S-812C57AUA-C3LT2x  S-812C57AY-n2-U

5.8 V2.0 % S-812C58AMC-C3MT2x S-812C58AUA-C3MT2x  S-812C58AY-n2-U

5.9 V2.0 % S-812C59AMC-C3NT2x S-812C59AUA-C3NT2x  S-812C59AY-n2-U

6.0 V2.0 % S-812C60AMC-C3OT2x S-812C60AUA-C3OT2x  S-812C60AY-n2-U

*1. “n” changes according to the packing form in TO-92.

B: Bulk, Z: Tape and ammo.

Remark 1. Please contact our sales office for products with an output voltage value other than those

specified above.

2. x: G or U

3. Please select products of environmental code = U for Sn 100%, halogen-free products.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

3. 2 S-812CxxB Series (Available short-circuit protection and power-off function)

Table 2 (1 / 2)

Output voltage SNT-6A(H) SOT-23-5 SOT-89-5

2.0 V2.0 % S-812C20BPI-C4ATFU S-812C20BMC-C4AT2x 

2.1 V2.0 % S-812C21BPI-C4BTFU S-812C21BMC-C4BT2x 

2.2 V2.0 % S-812C22BPI-C4CTFU S-812C22BMC-C4CT2x 

2.3 V2.0 % S-812C23BPI-C4DTFU S-812C23BMC-C4DT2x 

2.4 V2.0 % S-812C24BPI-C4ETFU S-812C24BMC-C4ET2x 

2.5 V2.0 % S-812C25BPI-C4FTFU S-812C25BMC-C4FT2x 

2.6 V2.0 % S-812C26BPI-C4GTFU S-812C26BMC-C4GT2x 

2.7 V2.0 % S-812C27BPI-C4HTFU S-812C27BMC-C4HT2x 

2.8 V2.0 % S-812C28BPI-C4ITFU S-812C28BMC-C4IT2x 

2.9 V2.0 % S-812C29BPI-C4JTFU S-812C29BMC-C4JT2x 

3.0 V2.0 % S-812C30BPI-C4KTFU S-812C30BMC-C4KT2x 

3.1 V2.0 % S-812C31BPI-C4LTFU S-812C31BMC-C4LT2x 

3.2 V2.0 % S-812C32BPI-C4MTFU S-812C32BMC-C4MT2x 

3.3 V2.0 % S-812C33BPI-C4NTFU S-812C33BMC-C4NT2x S-812C33BUC-C4NT2x

3.4 V2.0 % S-812C34BPI-C4OTFU S-812C34BMC-C4OT2x 

3.5 V2.0 % S-812C35BPI-C4PTFU S-812C35BMC-C4PT2x 

3.6 V2.0 % S-812C36BPI-C4QTFU S-812C36BMC-C4QT2x 

3.7 V2.0 % S-812C37BPI-C4RTFU S-812C37BMC-C4RT2x 

3.8 V2.0 % S-812C38BPI-C4STFU S-812C38BMC-C4ST2x 

3.9 V2.0 % S-812C39BPI-C4TTFU S-812C39BMC-C4TT2x 

4.0 V2.0 % S-812C40BPI-C4UTFU S-812C40BMC-C4UT2x 

4.1 V2.0 % S-812C41BPI-C4VTFU S-812C41BMC-C4VT2x 

4.2 V2.0 % S-812C42BPI-C4WTFU S-812C42BMC-C4WT2x 

4.3 V2.0 % S-812C43BPI-C4XTFU S-812C43BMC-C4XT2x 

4.4 V2.0 % S-812C44BPI-C4YTFU S-812C44BMC-C4YT2x 

4.5 V2.0 % S-812C45BPI-C4ZTFU S-812C45BMC-C4ZT2x 

4.6 V2.0 % S-812C46BPI-C5ATFU S-812C46BMC-C5AT2x 

4.7 V2.0 % S-812C47BPI-C5BTFU S-812C47BMC-C5BT2x 

4.8 V2.0 % S-812C48BPI-C5CTFU S-812C48BMC-C5CT2x 

4.9 V2.0 % S-812C49BPI-C5DTFU S-812C49BMC-C5DT2x 

5.0 V2.0 % S-812C50BPI-C5ETFU S-812C50BMC-C5ET2x S-812C50BUC-C5ET2x

5.1 V2.0 % S-812C51BPI-C5FTFU S-812C51BMC-C5FT2x 

5.2 V2.0 % S-812C52BPI-C5GTFU S-812C52BMC-C5GT2x 

5.3 V2.0 % S-812C53BPI-C5HTFU S-812C53BMC-C5HT2x 

5.4 V2.0 % S-812C54BPI-C5ITFU S-812C54BMC-C5IT2x 

5.5 V2.0 % S-812C55BPI-C5JTFU S-812C55BMC-C5JT2x 

5.6 V2.0 % S-812C56BPI-C5KTFU S-812C56BMC-C5KT2x 

5.7 V2.0 % S-812C57BPI-C5LTFU S-812C57BMC-C5LT2x 

5.8 V2.0 % S-812C58BPI-C5MTFU S-812C58BMC-C5MT2x 

5.9 V2.0 % S-812C59BPI-C5NTFU S-812C59BMC-C5NT2x 

6.0 V2.0 % S-812C60BPI-C5OTFU S-812C60BMC-C5OT2x 

Remark 1. Please contact our sales office for products with an output voltage value other than those

specified above.

2. x: G or U

3. Please select products of environmental code = U for Sn 100%, halogen-free products.

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

Table2 (2 / 2)

Output voltage WLP-4R

3.3 V2.0% S-812C33B-H4T1S

4.0 V2.0% S-812C40B-H4T1S

5.0 V2.0% S-812C50B-H4T1S

Remark Please contact our sales office for products with an output voltage value other than those

specified above.

3. 3 S-812CxxE Series (Available short-circuit protection function, unavailable power-off function)

Table 3

Output voltage SOT-23-5 SOT-89-3 SOT-89-5 TO-92*1

3.3 V2.0 %  S-812C33EUA-C5PT2x  

3.6 V2.0 %  S-812C36EUA-C5RT2x  

4.0 V2.0 %  S-812C40EUA-C5QT2x  

*1. “n” changes according to the packing form in TO-92.

B: Bulk, Z: Tape and ammo.

Remark 1. Please contact our sales office for products with an output voltage value other than those

specified above.

2. x: G or U

3. Please select products of environmental code = U for Sn 100%, halogen-free products.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

 Pin Configurations

SNT-6A(H)

Top view

3 4

Figure 4

Table 4

Pin No. Symbol Description

1 NC*1 No connection

2 VIN Input voltage pin

3 VOUT Output voltage pin

4 VSS GND pin

5 VIN Input voltage pin

6 ON/OFF ON/OFF pin

*1. The NC pin is electrically open.

The NC pin can be connected to VIN pin or VSS pin.

SOT-23-5

Top view

Figure 5

Table 5

Pin No. Symbol Description

1 VSS GND pin

2 VIN Input voltage pin

3 VOUT Output voltage pin

4 NC*1 No connection

5 ON/OFF ON/OFF pin (B type)

NC*1 No connection (A type, E type)

*1. The NC pin is electrically open.

The NC pin can be connected to VIN pin or VSS pin.

SOT-89-3

Top view

Table 6

Pin No. Symbol Description

1 VSS GND pin

2 VIN Input voltage pin

3 VOUT Output voltage pin

Figure 6

SOT-89-5

Top view

1 3

4 5

Table 7

Pin No. Symbol Description

1 VOUT Output voltage pin

2 VIN Input voltage pin

3 VSS GND pin

4 ON/OFF ON/OFF pin (B type)

NC*1 No connection (A type, E type)

5 NC*1 No connection

*1. The NC pin is electrically open.

The NC pin can be connected to VIN pin or VSS pin.

Figure 7

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

TO-92

Bottom view

1 3 2

Table 8

Pin No. Symbol Description

1 VSS GND pin

2 VIN Input voltage pin

3 VOUT Output voltage pin

Figure 8

WLP-4R

Top view Bottom view

B1 B2

B2 B1

Table 9

Pin No. Symbol Description

A1 VOUT Output voltage pin

B1 VIN Input voltage pin

A2 VSS GND pin

B2 ON/OFF

ON/OFF pin

Figure 9

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

 Absolute Maximum Ratings

Table 10

(Ta=25C unless otherwise specified)

Item Symbol Absolute Maximum Rating Units

Input voltage VIN VSS



0.3 to VSS



18 V

VON/OFF VSS



0.3 to VIN



0.3 V

Output voltage VOUT VSS



0.3 to VIN



0.3 V

Power dissipation

SNT-6A(H)

500*1 mW

SOT-23-5 250 (When not mounted on board) mW

600*1 mW

SOT-89-3 500 (When not mounted on board) mW

1000*1 mW

SOT-89-5 500 (When not mounted on board) mW

1000*1 mW

TO-92 400 (When not mounted on board) mW

800*1 mW

Operation ambient temperature To



40 to



85 C

Storage temperature Tst



40 to



125 C

*1. When mounted on board

[Mounted board]

(1) Board size : 114.3 mm  76.2 mm  t1.6 mm

(2) Board name : JEDEC STANDARD51-7

Caution The absolute maximum ratings are rated values exceeding which the product could suffer

physical damage. These values must therefore not be exceeded under any conditions.

050 100 150

1200

800

Power dissipation (PD) [mW]

mbient temperature (Ta) [C]

SOT-89-5

SOT-89-3

400

SNT-6A(H)

1000

200

600

TO-92

SOT-23-5

Figure 10 Power Dissipation of The Package (When mounted on Board)

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Electrical Characteristics

Table 11

(Ta=25C unless otherwise specified)

Item Symbol Conditions Min. Typ. Max. Units Test

circuits

Output voltage

VOUT(E)

= V

OUT(S)



2V, I

OUT

= 10mA V

OUT(S)



0.98 V

OUT(S)



1.02 V 1

Output current

IOUT

OUT(S)





16V

2.0V



OUT

(

)



2.9V 30



3.0V



OUT

(

)



3.9V 50



4.0V



OUT

(

)



4.9V 65



5.0V



OUT

(

)



6.0V 75



Dropout voltage

Vdrop

OUT

10mA

2.0V



OUT

(

)



2.4V



0.46 0.95 V 1

2.5V



OUT

(

)



2.9V



0.32 0.68 V 1

3.0V



OUT

(

)



3.4V



0.23 0.41 V 1

3.5V



OUT

(

)



3.9V



0.19 0.35 V 1

4.0V



OUT

(

)



4.4V



0.16 0.30 V 1

4.5V



OUT

(

)



4.9V



0.14 0.27 V 1

5.0V



OUT

(

)



5.4V



0.12 0.25 V 1

5.5V



OUT

(

)



6.0V



0.11 0.23 V 1

Line regulation 1

 VOUT11

OUT(S)





16V,

= 1m



5 20 mV 1

Line regulation 2

 VOUT21

OUT(S)





16V,

= 1





5 20 mV 1

Load regulation

 VOUT31

= V

OUT(S)



2.0V



OUT(S)



2.9V,





20m



6 30 mV 1

3.0V



OUT(S)



3.9V,





30mA



10 45 mV 1

4.0V



OUT(S)



4.9V,





40mA



13 65 mV 1

5.0V



OUT(S)



6.0V,





50m



17 80 mV 1

Output voltage

temperature coefficient



VOUT

Ta VOUT

= V

OUT(S)



1V, I

OUT

= 10mA,













100



ppm/



Current consumption

ISS

VOUT(S)

2V,

no load

2.0V



OUT

(

)



2.7V



0.9 1.6



2.8V



OUT

(

)



3.7V



1.0 1.8



3.8V



OUT

(

)



5.1V



1.2 2.1



5.2V



OUT

(

)



6.0V



1.5 2.5



Input voltage

VIN



16 V 1

Applied to products with powe

-of

unction

Current consumption

during power-off

ISS2

= V

OUT(S)



2V,

ON/OF

= 0V, no load



0.1 0.5



A 2

ON/OFF pin

input voltage “H”

VSH

= V

OUT(S)



2V,

= 1k



determined by V

output level 2.0



V 4

ON/OFF pin

input voltage “L”

VSL

= V

OUT(S)



2V,

= 1k



determined by V

output level



0.4 V 4

ON/OFF pin

input current “H”

ISH

= 7V, V

ON/OFF

= 7V -0.1



0.1



A 4

ON/OFF pin

input current “L”

ISL

= V

OUT(S)



2V, V

ON/OFF

= 0V -0.1



0.1



A 4

Applied to products with short-circuit protection

unction

Shor

circuit curren

IOS

= V

OUT

(

)



2V, V

= 0V



16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

*1. VOUT(S): Set output voltage

OUT(E) Actual output voltage

Output voltage when fixing IOUT(=10 mA) and inputting VOUT(S)2.0V.

*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output

current.

*3. V

drop = VIN1(VOUT(E)  0.98)

IN1 is the input voltage at which the output voltage becomes 98% of VOUT(E) after gradually decreasing the

input voltage.

*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.

VOUT

Ta []

mV/°C *1 = VOUT(S) []

V*2  VOUT

Ta VOUT

[]

ppm/°C *3  1000

*1. Change in temperature of output voltage

*2. Set output voltage

*3. Output voltage temperature coefficient

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Test Circuits

VSS

VOUT

(ON/OFF)

Set to ON

VIN

Figure 11

VSS

VOUT

(ON/OFF)

VIN

Set to VIN or

GND

Figure 12

Set to ON

VSS

VOUT

(ON/OFF)

VIN

Figure 13

VSS

VOUT

(ON/OFF)

VIN

Figure 14

*1. In case of product with power-off function.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

 Standard Circuit

VSS

VOUT

(ON/OFF)*3



VIN

CIN

INPUT OUTPUT

GND

Single GND

1. CIN is a capacitor for stabilizing the input.

2. In addition to tantalum capacitor, ceramic capacitor can be used for CL.

3. Control this ON/OFF pin in the product with power-off function.

Figure 15

Caution The above connection diagram and constant will not guarantee successful operation.

Perform through evaluation using the actual application to set the constant.

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Explanation of Terms

1. Output capacitor (CL)

Generally in voltage regulator, output capacitor is used to stabilize regulation and to improve the

characteristics of transient response. The S-812C Series operates stably without output capacitor CL.

Thus the output capacitor CL is used only for improvement of the transient response. In the applications

that users will use the S-812C Series, and they are not cautious about the transient response, it is

possible to omit an output capacitor. If using an output capacitor for this IC, users are able to use devices

such as ceramic capacitor which has small ESR (Equivalent Series Resistance).

2. Output voltage (VOUT)

The accuracy of the output voltage  2.0% is assured under the specified conditions for input voltage,

which differs depending upon the product items, output current, and temperature.

Caution If the above conditions change, the output voltage value may vary and go out of the

accuracy range of the output voltage. Refer to " Electrical Characteristics" and "

Characteristics (Typical Data)" for details.

3. Line regulations 1 and 2 (VOUT1, VOUT2)

Indicate the dependency of the output voltage against the input voltage. That is, the value shows how

much the output voltage changes due to a change in the input voltage after fixing output current constant.

4. Load regulation (VOUT3)

Indicates the dependency of the output voltage against the output current. That is, the value shows how

much the output voltage changes due to a change in the output current after fixing output current

constant.

5. Dropout voltage (Vdrop)

Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input

voltage (VIN) gradually until the output voltage has dropped out to the value of 98% of the actual output

voltage (VOUT(E)).

Vdrop = VIN1  (VOUT(E)  0.98)

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

6. Output voltage temperature coefficient 





VOUT

Ta  VOUT

The shaded area in Figure 16 is the range where VOUT varies in the operation temperature range when

the output voltage temperature coefficient is 100 ppm/C.

OUT

(

)

Example of S-812C30A typ. product

40



0.30 mV/C

OUT

[V]

*1. V

OUT(E)

is the value of the output voltage measured at Ta = 25C.



85 Ta [C]



0.30 mV/C

Figure 16

A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.

VOUT

Ta []

mV/°C *1 = VOUT(S) []

V*2  VOUT

Ta  VOUT

[]

ppm/°C*3  1000

*1. Change in temperature of output voltage

*2. Set output voltage

*3. Output voltage temperature coefficient

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Operation

1. Basic operation

Figure 17 shows the block diagram of the S-812C Series.

The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output

voltage resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to

maintain the constant output voltage which is not influenced by the input voltage and temperature

change, to the output transistor.

*1. Parasitic diode

VSS

Current

supply





Vfb

Vref

VIN

VOUT

Error

amplifier

Reference voltage

circuit

Figure 17

2. Output transistor

In the S-812C Series, a low on-resistance P-channel MOS FET is used as the output transistor.

Be sure that VOUT does not exceed VIN  0.3 V to prevent the voltage regulator from being damaged due

to reverse current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential

of VOUT became higher than VIN.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

3. ON/OFF pin

This pin starts and stops the regulator.

When the ON/OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in

P-channel MOS FET output transistor between the VIN pin and the VOUT pin is turned off, reducing

current consumption significantly. The VOUT pin becomes the VSS level due to the internally divided

resistance of several M between the VOUT pin and the VSS pin.

The structure of the ON/OFF pin is as shown in Figure 18. Since the ON/OFF pin is neither pulled down

nor pulled up internally, do not use it in the floating status. Note that if applying the voltage of VIN + 0.3 V

or more, the current flows to VIN via a parasitic diode in the IC.

When not using the ON/OFF pin in the product with the power-off function, connect the ON/OFF pin to

the VIN pin (in positive logic), or to the VSS pin (in negative logic).

The output voltage may increase by stopping regulation when a lower current (100 A or less) is

applied.

If the output voltage increased during power-off, pull the VOUT pin down to the VSS pin and set the

ON/OFF pin to the power-down level.

Table 12

Product Type ON/OFF Pin Internal Circuit VOUT Pin Voltage Current Consumption

B “L”: OFF Stop VSS level ISS2

B “H”: ON Operate Set value ISS

VIN

ON/OFF

VSS

Figure 18

4. Short-circuit protection circuit

In the S-812C Series, users are able to select whether to set the short circuit protection, which protects

the output capacitor from short-circuiting between the VOUT pin and the VSS pin.

The short circuit protection circuit controls the output current against voltage VOUT, as seen in “

Characteristics (Typical Data)”, “1. Output Voltage vs Output Current (When load current

increases)”, and limits the output current at approx. 40 mA even if the VOUT pin and the VSS pins are

short-circuited.

However, this short circuit protection circuit does not work as for thermal protection. Pay attention to the

conditions of input voltage and load current so that, under the usage condition including short circuit, the

loss of the IC will not exceed power dissipation of the package.

Even if pins are not short-circuited, this protection circuit works to limit the current to the specified value,

in order to protect the output capacitor, when the output current and the potential difference between

input and output voltages increase.

In the product without the short circuit protection circuit, the S-812C Series allows the relatively larger

current because this protection circuit is detached.

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Selection of External Components

1. Output capacitor (CL)

The S-812C Series has an internal phase compensation circuit which stabilizes the operation regardless

of the change of output load. Therefore it is possible for users to have a stable operation without an

output capacitor (CL). However, the values of output overshoot and undershoot, which are the

characteristics of transient response, vary depending on the output capacitor. In selecting the value of

output capacitor, refer to the data on CL dependency in “ Reference data”, “1. Transient response

characteristics (Typical data: Ta25 C)”.

Set ESR 10  or less when using a tantalum capacitor or an aluminum electrolytic capacitor. Pay

attention at low temperature, that aluminum electrolytic capacitor especially may oscillate because ESR

increases. Evaluate sufficiently including the temperature characteristics in use.

 Application Circuit

1. Output current boost circuit

As shown in Figure 19, the output current can be boosted by externally attaching a PNP transistor.

Between the input voltage VIN and the VIN pin (for power supply) in the S-812C Series, if setting the

base-emitter voltage VBE which fully switches the PNP transistor on, S-812C Series controls the base

current in a PNP transistor so that the output voltage VOUT reaches the level of voltage which is set by

the S-812C Series.

Since the output current boosting circuit in Figure 19 does not have the good characteristics of transient

response, under the usage condition, confirm if output fluctuation due to power-on, and fluctuations of

power supply and load affect on the operation or not before use.

Note that the short-circuit protection circuit in the S-812C Series does not work as short-circuit protection

for this boost circuit.

Tr1

GND

VOUT

ON/OFF

VIN

VSS

OUT

S-812C

Series

Figure 19

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

2. Constant current circuit

This circuit can be used as a constant current circuit if making the composition seen in Figure 20 and

21. Constant current IO is calculated from the following equation (VOUT(E) = actual output voltage):

IO = (VOUT(E)  RL) + ISS

Note that by using a circuit in Figure 20, it is impossible to set the better driving ability to the constant

amperage (IO) than the S-812C Series basically has.

To gain the driving ability which exceeds the S-812C Series, there’s a way to combine a constant

current circuit and a current boosting circuit, as seen in Figure 21.

The maximum input voltage for a constant current circuit is 16 V + the voltage for device (VO).

It is not recommended to add a capacitor between the VIN pin (power supply) and the VSS pin or the

VOUT pin (output) and the VSS pin because the rush current flows at power-on.

GND

VOUTVIN

OUT

ON/OFF VSS

S-812C

Series

Device

Figure 20 Constant Current Circuit

ON/OFF

GND

VOUT

OUT

VSS

S-812C

Series

Tr1

Device

VIN

Figure 21 Constant Current Boost Circuit

3. Output voltage adjustment circuit

(Only for S-812CxxA Series (Unavailable short-circuit protection and power-off function))

By using the composition seen in Figure 22, users are able to increase the output voltage. The value of

output voltage VOUT1 is calculated from the following equation (VOUT(E) = actual output voltage):

VOUT1 = VOUT(E)  (R1 + R2)  R1 + R2  ISS

Set the value of resistors R1 and R2 so that the S-812C Series is not affected by current consumption

ISS.

Capacitor C1 reduces output fluctuation due to power-on, power fluctuation and load fluctuation. Set the

value according to the actual evaluation.

It is not recommended to add a capacitor between the VIN pin (power supply) and the VSS pin or the

VOUT pin (output) and the VSS pin because it causes output fluctuation and output oscillation due to

power-on.

GND

OUT1

VOUTVIN V

VSS

S-812C

Series

Figure 22

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Precautions

 Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low.

When mounting an output capacitor between the VOUT pin and the VSS pin (CL) and a capacitor for

stabilizing the input between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these

pins should be as short as possible.

 Note that generally the output voltage may increase when a series regulator is used at low load current

(1 A or less).

 At low load current (100 A or less) output voltage may increase when the regulating operation is halted

by the ON/OFF pin.

 Generally a series regulator may cause oscillation, depending on the selection of external parts. The

following conditions are recommended for the S-812C Series. However, be sure to perform sufficient

evaluation under the actual usage conditions for selection, including evaluation of temperature

characteristics.

Equivalent Series Resistance (ESR): 10  or less (in case of using output capacitor)

Input series resistance (RIN): 10  or less

 The voltage regulator may oscillate when the impedance of the power supply is high and the input

capacitance is small or an input capacitor is not connected.

 Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when

the power supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.

 The application conditions for the input voltage, the output voltage, and the load current should not exceed

the package power dissipation.

 Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in

electrostatic protection circuit.

 ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by

products including this IC of patents owned by a third party.

 Precautions for WLP package

● The side of device silicon substrate is exposed to the marking side of device package. Since this portion has lower

strength against the mechanical stress than the standard plastic package, chip, crack, etc should be careful of the

handing of a package enough. Moreover, the exposed side of silicon has electrical potential of device substrate, and

needs to be kept out of contact with the external potential.

● In this package, the overcoat of the resin of translucence is carried out on the side of device area. Keep it mind that it

may affect the characteristic of a device when exposed a device in the bottom of a high light source.

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

 Characteristics (Typical Data)

1. Output Voltage vs Output Current (When load current increases)

0.0

0.5

1.0

1.5

2.0

2.5

0 50 100 150

IOUT (mA)

VOUT

(V)

VIN=2.5V

S-812C20B (Ta=25°C) Short- circuit protection

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0 50 100 150 200

IOUT (mA)

VOUT

(V)

VIN=3.5V

S-812C30B (Ta=25°C) Short-circuit protection

0.0

1.0

2.0

3.0

4.0

5.0

6.0

0 100 200 300

IOUT (mA)

VOUT

(V)

VIN=5.5V

10V

S-812C50B (Ta=25°C) Short-circuit protection

VOUT (V)

No short-circuit protection

S-812C20A (Ta=25ºC)

0.0

0.5

1.0

1.5

2.0

2.5

0 100 200 300

IOUT (mA)

5V4V

2.5V

VIN=2.3V

VOUT (V)

S-812C30A (Ta=25ºC)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0 100 200 300 400

OUT

(mA)

3.5V

=3.3V

No short-circuit protection

VOUT (V)

S-812C50A (Ta=25ºC)

0.0

1.0

2.0

3.0

4.0

5.0

6.0

0 100 200 300 400

OUT

(mA)

10V

5.5V

=5.3V

No short-circuit protection

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

2. Maximum Output Current vs Input Voltage

IOUTMAX (mA)

100

120

140

0481216

VIN (V)

Ta=-40°C

S-812C20B Short-circuit protection

25°C 85°C

IOUTMAX (mA)

100

150

200

0481216

VIN (V)

Ta=-40°C

S-812C30B Short-circuit protection

25°C

85°C

IOUTMAX (mA)

100

150

200

250

300

0481216

VIN (V)

Ta=-40°C

S-812C50B Short-circuit protection

25°C

85°C

IOUTMAX (mA)

S-812C20A

100

120

140

0481216

VIN

(

)

85ºC

Ta=-40ºC

25ºC

No short-circuit protection

IOUTMAX (mA)

S-812C30A

100

150

200

0481216

VIN

(

)

85ºC

Ta=40ºC

25ºC

No short-circuit protection

IOUTMAX (mA)

No short-circuit protection

S-812C50A

100

150

200

250

300

0481216

VIN(V)

85ºC

Ta=-40ºC

25ºC

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

3. Output Current vs. Input Voltage

S-812C20B (Ta=25°C)

2.10

2.05

2.00

1.95

1.90

1.5 2 2.5 3 3.5 4

OUT

(V)

-50 mA

-20 mA

-10 mA

-1 mA

OUT

=-1



(V)

S-812C30B (Ta=25°C)

3.15

3.10

3.05

2.95

2.85

2.5 33.5 4 4.5

OUT

(V)

-50 mA

-20 mA

-10 mA

-1 mA

OUT

=-1



(V)

3.00

2.90

S-812C50B (Ta=25°C)

5.25

5.15

5.05

4.95

4.5 5 5.5 6 6.5 7

VOUT (V)

-50 mA

-20 mA

-1 mA

OUT

=-1



VIN (V)

4.85

4.75

-10 mA

4. Dropout Voltage vs Output Current

500

1000

1500

2000

0 10 20 30 40 50

IOUT

(

)

Vdro

(

)

Ta=-40°C

S-812C20B

25°C

85°C

200

400

600

800

1000

1200

1400

1600

010 20 30 40 50

OUT

(

)

Vdro

(

)

Ta=-40°C

S-812C30B

25°C

85°C

100

200

300

400

500

600

700

800

900

1000

0 10 20 30 40 50

IOUT

(

)

Vdro

(

)

Ta=-40°C

S-812C50B

25°C

85°C

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

5. Output Voltage vs Ambient Temperature

-50

2.02

Ta (°C)

VOUT (V)

2.04

2.00

1.98

1.96 0 50

100

S-812C20B

-50

3.03

Ta (°C)

OUT

(V)

3.06

3.00

2.97

2.94 050

100

S-812C30B

-50

5.05

Ta (°C)

VOUT (V)

5.10

5.00

4.95

4.90 0 50

100

S-812C50B

6. Line Regulation 1 vs Ambient Temperature 7. Line Regulation 2 vs Ambient Temperature

-50

Ta (°C)

VOUT1 (mV)

0 0 50

100

S-812C50B

S-812C20B

S-812C30B

-50

Ta (°C)

VOUT2 (mV)

0050

100

S-812C50B

S-812C20B

S-812C30B

8. Load Regulation vs Ambient Temperature

-50

Ta (°C)

VOUT3 (mV)

0 0 50

100

S-812C50B

S-812C30B

S-812C20B

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

9. Current Consumption vs Input Voltage

0.0

0.5

1.0

1.5

2.0

2.5

0481216

VIN (V)

ISS (A)

S-812C20B

25°C 85°C

Ta=-40°C

0.0

0.5

1.0

1.5

2.0

2.5

0 4 8 12 16

VIN (V)

ISS (A)

S-812C30B

25°C 85°C

Ta=-40°C

0.0

0.5

1.0

1.5

2.0

2.5

0481216

VIN (V)

ISS (A)

S-812C50B

25°C 85°C

Ta=-40°C

0. ON/OFF Pin Input Threshold vs Input Voltage

0.0

0.5

1.0

1.5

2.0

2.5

0 4 8 12 16

(V)

/ V

(V)

Ta40°C

25°C

85°C

Ta40°C

25°C

85°C

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

 Reference Data

1. Transient Response Characteristics (Typical data: Ta25 C)

Overshoot

Input voltage

O utput voltage

Load current

Undershoot

-1. Power-on : S-812C30B (CL=10F; ceramic capacitor)

TIME

(

100



s/div

)

VOUT (0.5 V/div)

0 V

5 V

0 V

3 V

VIN, VON/OFF05 V, IOUT10 mA, CL10 F

Load dependency of overshoot at power-on CL dependency of overshoot at power-on

0.000

0.005

0.010

0.015

0.020

0.025

0.030

0 0.02 0.04 0.06 0.08 0.1

IOUT (A)

Overshoot (V)

S-812C50B

S-812C30B

VIN, VON/OFF0VOUT(S)2 V, CL10 F

0.0

0.2

0.4

0.6

0.8

0 10 20 30 40 50

(



)

Overshoot (V)

S-812C50B

VIN, VON/OFF0VOUT(S)2 V, IOUT10 mA

S-812C30B

VDD dependency of overshoot at power-on “Ta” dependency of overshoot at power-on

0.000

0.005

0.010

0.015

0.020

0.025

0.030

0.035

0 5 10 15 20

VDD (V)

Overshoot (V)

S-812C50B

VIN, VON/OFF



0VDD, IOUT10 mA,

10



S-812C30B

0.00

0.01

0.02

0.03

0.04

0.05

0.06



50 0 50 100

Ta (°C)

Overshoot (V)

S-812C50B

VIN, VON/OFF0VOUT(S)2 V, IOUT10 mA,

10



S-812C30B

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

-2. ON/OFF pin : S-812C30A (CL=10F; ceramic capacitor)

TIME

(

200



s/div

)

VOUT (0.5 V/div)

5 V

0 V

3 V

5 V

ON/OFF

05 V

OUT

10 mA





load dependency of overshoot with ON/OFF pin CL dependency of overshoot with ON/OFF pin

0.0

0.2

0.4

0.6

0.8

0.001 0.01 0.1 1 10 100

IOUT (mA)

Overshoot (V)

S-812C50B

VINVOUT(S)2 V, VON/OFF0 VOUT(S)2 V,

CL10 F

S-812C30B

0.0

0.2

0.4

0.6

0.8

0 10 20 30 40 50

(



)

Overshoot (V)

S-812C50B

VINVOUT(S)2 V, VON/OFF0VOUT(S)2 V,

IOUT10 mA

S-812C30B

VDD dependency of overshoot with ON/OFF pin “Ta” dependency of overshoot with ON/OFF pin

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0 5 10 15 20

VDD (V)

Overshoot (V)

S-812C50B

VINVDD, VON/OFF0VDD, IOUT10 mA,

CL10 F

S-812C30B

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8



50 0 50 100

Ta (°C)

Overshoot (V)

S-812C50B

VINVOUT(S)2 V, VON/OFF0VOUT(S)2 V,

IOUT10 mA, CL10 F

S-812C30B

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

1-3. Power supply fluctuates: S-812C30B (CL=10F; ceramic capacitor)

ON/OFF



4 8 V

OUT

10 m

TIME

(

100



s/div

)

VOUT (0.05V / div)

10 V

0 V

5 V

3 V

2.9 V

Load dependency of overshoot at power supply fluctuates

dependency of overshoot at power supply fluctuates

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16

0 10 20 30 40 50

IOUT (mA)

Overshoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)1 VVOUT(S)5 V,

CL10 F

S-812C30B

0.00

0.05

0.10

0.15

0.20

0.25

0 10 20 30 40 50

(



)

Overshoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)1 VVOUT(S)5 V,

IOUT10 m

S-812C30B

dependency of overshoot at power supply fluctuates “Ta” dependency of overshoot at power supply fluctuates

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16

0 5 10 15 20

VDD (V)

Overshoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)1 VVDD, IOUT10 mA,

CL10 F

S-812C30B

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16



50 0 50 100

Ta (°C)

Overshoot (V)

S-812C50B

VIN, VON/OFF



VOUT(S)1 VVOUT(S)5 V,

IOUT10 mA, CL10 F

S-812C30B

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

TIME

(

500



s/div

)

VOUT (0.05 V / div)

10 V

0 V

5 V

3 V

2.8

2.9

VIN, VON/OFF84 V, IOUT10 mA

Load dependency of undershoot at power supply fluctuates C

dependency of undershoot at power supply fluctuates

0.0

0.2

0.4

0.6

0.8

0 10 20 30 40 50

IOUT (mA)

Undershoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)5 VVOUT(S)1 V,

CL10 F

S-812C30B

0.00

0.05

0.10

0.15

0.20

0.25

0.30

0.35

0 10 20 30 40 50

(



)

Undershoot (V)

S-812C50B

VIN, VON/OFF VOUT(S)5 VVOUT(S)1 V,

IOUT10 mA

S-812C30B

dependency of undershoot at power supply fluctuates “Ta” dependency of undershoot at power supply fluctuates

0.00

0.05

0.10

0.15

0.20

0.25

0 5 10

15 20

VDD (V)

Undershoot (V)

S-812C50B

VIN, VON/OFFVDDVOUT(S)1 V,

IOUT10mA, CL10 F

S-812C30B

0.00

0.05

0.10

0.15

0.20

0.25

0.30



50 0 50 100

Ta (°C)

Undershoot (V)

S-812C50B

S-812C30B

VIN, VON/OFF



VOUT(S)5 VVOUT(S)1 V,

IOUT10mA, CL10 F

16 V INPUT, 75 mA VOLTAGE REGULATOR

S-812C Series Rev.7.0_01

-4. Load fluctuation: S-812C30B (CL=10F; ceramic capacitor)

5 V

OUT

10 mA1



10



TIME (200 ms / div)

VOUT (0.05 V / div)

2.9 V

3.1 V

3 V

0 mA

10 mA

Load dependency of overshoot at load fluctuation CL dependency of overshoot at load fluctuation

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0 20 40 60 80 100

ILoad (mA)

Overshoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)2 V,

IOUTILoad1 A, CL10F

S-812C30B

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16

0 10 20 30 40 50

(



)

Overshoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)2 V,

IOUT10 mA1 A

S-812C30B

VDD dependency of overshoot at load fluctuation “Ta”

dependency of overshoot at load

fluctuation

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16

0 5 10 15 20

VDD (V)

Overshoot (V)

S-812C50B

IOUT10 mA1 A, CL10



S-812C30B

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16



50 0 50 100

Ta (°C)

Overshoot (V)

S-812C50B

VIN, VON/OFF=VOUT(S)2 V,

IOUT10 mA1 A, CL10 F

S-812C30B

16 V INPUT, 75 mA VOLTAGE REGULATOR

Rev.7.0_01 S-812C Series

TIME

(

500



s / div

)

VOUT (0.05 V / div)

2.9 V

3 V

VIN5 V, IOUT1 A,10 mA, CL10



0 mA

10 mA

Load dependency of undershoot at load fluctuation CL dependency of undershoot at load fluctuation

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0 20 40

60 80 100

ILoad (mA)

Undershoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)2 V,

IOUT1 AILoad, CL10F

S-812C30B

0.00

0.05

0.10

0.15

0.20

0.25

0 10 20 30 40 50

(



)

Undershoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)2 V,

IOUT1 A10 mA

S-812C30B

VDD dependency of undershoot at load fluctuation “Ta”

dependency of undershoot at load

fluctuation

0.00

0.05

0.10

0.15

0.20

0 5 10 15 20

VDD (V)

Undershoot (V)

S-812C50B

IOUT1



A10 mA, CL10



S-812C30B

0.00

0.05

0.10

0.15

0.20

0.25



50 0 50 100

Ta (°C)

Undershoot (V)

S-812C50B

VIN, VON/OFFVOUT(S)2 V,

IOUT1 A10 mA, CL10 F

S-812C30B

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

SNT-6A(H)-A-PKG Dimensions

PI006-A-P-SD-2.1

0.2±0.05

0.48±0.02

0.08 +0.05

-0.02

0.5

1.57±0.03

No. PI006-A-P-SD-2.1

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

Feed direction

4.0±0.1

2.0±0.05

4.0±0.1

ø1.5 +0.1

-0

ø0.5

1.85±0.05 0.65±0.05

0.25±0.05

PI006-A-C-SD-2.0

SNT-6A(H)-A-Carrier Tape

No. PI006-A-C-SD-2.0

+0.1

-0

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

12.5max.

9.0±0.3

ø13±0.2

(60°) (60°)

QTY.

No. PI006-A-R-SD-1.0

PI006-A-R-SD-1.0

Enlarged drawing in the central part

SNT-6A(H)-A-Reel

5,000

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

SNT-6A(H)-A

-Land Recommendation

PI006-A-L-SD-4.1

No. PI006-A-L-SD-4.1

0.3

0.2

0.52

1.36

0.52

Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package.

2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm

or less from the land pattern surface.

3. Match the mask aperture size and aperture position with the land pattern.

4. Refer to "SNT Package User's Guide" for details.

1. (0.25 mm min. / 0.30 mm typ.)

2. (1.30 mm ~ 1.40 mm)

2. 0.03 mm

4. SNT

1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.).

2. Do not widen the land pattern to the center of the package (1.30 mm to 1.40 mm).

2. (1.30 mm ~ 1.40 mm)

(0.25 mm min. / 0.30 mm typ.)

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

2.9±0.2

1.9±0.2

0.95±0.1

0.4±0.1

0.16 +0.1

-0.06

123

No. MP005-A-P-SD-1.3

MP005-A-P-SD-1.3

SOT235-A-PKG Dimensions

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

ø1.5 +0.1

-0 2.0±0.05

ø1.0 +0.2

-0 4.0±0.1 1.4±0.2

0.25±0.1

3.2±0.2

123

No. MP005-A-C-SD-2.1

MP005-A-C-SD-2.1

SOT235-A-Carrier Tape

Feed direction

4.0±0.1(10 pitches:40.0±0.2)

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

12.5max.

9.0±0.3

ø13±0.2

(60°) (60°)

QTY. 3,000

No. MP005-A-R-SD-1.1

MP005-A-R-SD-1.1

SOT235-A-Reel

Enlarged drawing in the central part

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

0.4±0.05

1.5±0.1

4.5±0.1

1.6±0.2

1.5±0.1 1.5±0.1

0.45±0.1

0.4±0.1

45°

312

No. UP003-A-P-SD-2.0

UP003-A-P-SD-2.0

SOT893-A-PKG Dimensions

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

2.0±0.1

0.3±0.05

8.0±0.1

ø1.5 +0.1

-0

2.0±0.05

ø1.5+0.1

-0

4.75±0.1

No. UP003-A-C-SD-2.0

UP003-A-C-SD-2.0

SOT893-A-Carrier Tape

Feed direction

4.0±0.1(10 pitches : 40.0±0.2)

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

13.0±0.3

16.5max.

(60°)

QTY. 1,000

No. UP003-A-R-SD-1.1

UP003-A-R-SD-1.1

SOT893-A-Reel

Enlarged drawing in the central part

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

1.5±0.1 1.5±0.1

1.6±0.2

4.5±0.1

132

1.5±0.1

0.4±0.05

0.4±0.1

0.45±0.1

0.4±0.1

SOT895-A-PKG Dimensions

No. UP005-A-P-SD-2.0

UP005-A-P-SD-2.0

45°

0.3

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

2.0±0.1

0.3±0.05

8.0±0.1

ø1.5 +0.1

-0

2.0±0.05

ø1.5 +0.1

-0

4.75±0.1

No. UP005-A-C-SD-2.0

UP005-A-C-SD-2.0

SOT895-A-Carrier Tape

Feed direction

4.0±0.1(10 pitches : 40.0±0.2)

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

16.5max.

13.0±0.3

QTY. 1,000

(60°)

No. UP005-A-R-SD-1.1

UP005-A-R-SD-1.1

SOT895-A-Reel

Enlarged drawing in the central part

No.

TITLE

UNIT

ANGLE

No. YS003-D-P-SD-2.1

YS003-D-P-SD-2.1

TO92-D-PKG Dimensions

5.2max.

0.45±0.1

1.27

0.45±0.1

4.2max.

0.6max.

Marked side

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

No. YZ003-E-P-SD-2.1

YZ003-E-P-SD-2.1

TO92-E-PKG Dimensions

5.2max. 4.2max.

1.27

Marked side

0.45±0.1

2.5 +0.4

-0.1

0.6max.

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

12.7±1.0

6.35±0.4 ø4.0±0.2

1.0max. 1#pin 3#pin

1.0max. 1.0max.

0.7±0.2

1.45max.

Feed direction

Z type

12.7±0.3(20 pitches : 254.0±1.0)

Marked side

No. YZ003-E-C-SD-1.1

YZ003-E-C-SD-1.1

TO92-E-Radial Tape

No.

TITLE

UNIT

ANGLE

ABLIC Inc.

QTY. 2,000

YZ003-E-Z-SD-2.0

TO92-E-Ammo Packing

333

162

Spacer(Sponge)

312 35

154

314

Side spacer placed in front side

Space more than 4 strokes

No. YZ003-E-Z-SD-2.0

No.

TITLE

ANGLE

UNIT

ABLIC Inc.

0.6max.

0.73±0.03

No. HR004-A-P-SD-1.0

WLP-4R-A-PKG Dimensions

HR004-A-P-SD-1.0

B2 ON/OFF

VOUT

VSS

VIN

Pin No.

(S-812CXX)

0.4

ø0.22±0.03 0.06 S

4-(ø0.22)

ø0.05 MSAB

Symbol

No.

TITLE

ANGLE

UNIT

ABLIC Inc.

WLP-4R-A-Carrier Tape

HR004-A-C-SD-1.0

(S-812CXX)

No. HR004-A-C-SD-1.0

Feed direction

A1B1

A2B2

2.0±0.05

4.0±0.1

ø1.5 +0.1

-0 4.0±0.1

0.65±0.1

0.20±0.05

ø0.3±0.05

1.1±0.1

No.

TITLE

ANGLE

UNIT

ABLIC Inc.

No. HR004-A-R-SD-1.0

HR004-A-R-SD-1.0

WLP-4R-A-Reel

QTY. 3,000

(S-812CXX)

11.4±1.0

9.0

ø13±0.2

(60°) (60°)

Enlarged drawing in the central part

+1.0

- 0.0

Disclaimers (Handling Precautions)

1. All the information described herein

(product data,

specifications,

figures,

tables,

programs,

algorithms and application

circuit examples,

etc.)

is current as of publishing date of this document and is subject to change without notice.

2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of

any specific mass-production design.

ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein

(hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use

of the information described herein.

3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein.

4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings,

operation voltage range and electrical characteristics, etc.

ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the

products outside their specified ranges.

5. When using the products, confirm their applications, and the laws and regulations of the region or country where they

are used and verify suitability, safety and other factors for the intended use.

6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related

laws, and follow the required procedures.

7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass

destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to

develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use.

8. The products are not designed to be used as part of any device or equipment that may affect the human body, human

life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control

systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,

aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do

not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc.

Especially, the products cannot be used for life support devices, devices implanted in the human body and devices

that directly affect human life, etc.

Prior consultation with our sales office is required when considering the above uses.

ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products.

9. Semiconductor products may fail or malfunction with some probability.

The user of the products should therefore take responsibility to give thorough consideration to safety design including

redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or

death, fires and social damage, etc. that may ensue from the products' failure or malfunction.

The entire system must be sufficiently evaluated and applied on customer's own responsibility.

10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the

product design by the customer depending on the intended use.

11. The products do not affect human health under normal use. However, they contain chemical substances and heavy

metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be

careful when handling these with the bare hands to prevent injuries, etc.

12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.

13. The information described herein contains copyright information and know-how of ABLIC Inc.

The information described herein does not convey any license under any intellectual property rights or any other

rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any

part of this document described herein for the purpose of disclosing it to a third-party without the express permission

of ABLIC Inc. is strictly prohibited.

14. For more details on the information described herein, contact our sales office.

2.2-2018.06

www.ablic.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

ABLIC:

S-812C31AY-B-G S-812C25BPI-C4FTFG S-812C27BPI-C4HTFG S-812C20BPI-C4ATFG S-812C21BPI-C4BTFG

S-812C22BPI-C4CTFG S-812C23BPI-C4DTFG S-812C24BPI-C4ETFG S-812C26BPI-C4GTFG S-812C28BPI-

C4ITFG S-812C29BPI-C4JTFG S-812C30BPI-C4KTFG S-812C31BPI-C4LTFG S-812C32BPI-C4MTFG S-

812C33BPI-C4NTFG S-812C34BPI-C4OTFG S-812C35BPI-C4PTFG S-812C36BPI-C4QTFG S-812C37BPI-C4RTFG

S-812C38BPI-C4STFG S-812C39BPI-C4TTFG S-812C40BPI-C4UTFG S-812C41BPI-C4VTFG S-812C42BPI-

C4WTFG S-812C43BPI-C4XTFG S-812C44BPI-C4YTFG S-812C45BPI-C4ZTFG S-812C46BPI-C5ATFG S-

812C53BPI-C5HTFG S-812C54BPI-C5ITFG S-812C55BPI-C5JTFG S-812C56BPI-C5KTFG S-812C57BPI-C5LTFG

S-812C58BPI-C5MTFG S-812C59BPI-C5NTFG S-812C60BPI-C5OTFG S-812C20AY-B2-U S-812C50AY-B-G S-

812C53BPI-C5HTFU S-812C21BPI-C4BTFU S-81250SGUP-DQD-T1 S-81250SGY-B S-81230SGY-B S-

81215SGUP-DQK-T1 S-81225SGUP-DQH-T1 S-81230SGUP-DQB-T1 S-812C35AMC-C2P-T2 S-812C33AUA-C2N-

T2 S-812C49AY-B S-812C39AUA-C2T-T2 S-812C48AY-B S-812C35AUA-C2P-T2 S-812C33AMC-C2N-T2 S-

812C46AUA-C3A-T2 S-812C25AY-B S-81225SGY-B S-812C40AUA-C2U-T2 S-812C50AY-B S-812C34AUA-C2O-

T2 S-812C34AMC-C2O-T2 S-812C49AMC-C3D-T2 S-812C36AUA-C2Q-T2 S-812C42AMC-C2W-T2 S-812C35AY-B

S-81235SGY-B S-812C40AMC-C2U-T2 S-812C46AMC-C3A-T2 S-812C45AUA-C2Z-T2 S-812C25AMC-C2F-T2 S-

812C58AUA-C3M-T2 S-812C25AUA-C2F-T2 S-812C33AY-B S-812C30AMC-C2K-T2 S-812C50AUA-C3E-T2 S-

812C40AY-B S-812C30AUA-C2K-T2 S-812C30AY-B S-812C45AMC-C2Z-T2 S-812C20AUA-C2A-T2 S-

812C20AMC-C2A-T2 S-812C50AMC-C3E-T2 S-812C49AUA-C3D-T2 S-812C22AUA-C2C-T2 S-812C27AMC-C2H-

T2 S-812C37AMC-C2R-T2 S-81252SGUP-DQL-T1 S-81240SGUP-DQJ-T1 S-81240SGY-B S-812C52AUA-C3G-T2

S-812C29AMC-C2J-T2 S-812C48AUA-C3C-T2 S-812C26AY-Z2-U S-812C33AY-Z2-U S-812C42AY-Z2-U S-

812C35AY-Z2-U S-812C43AY-Z2-U S-812C57AY-Z2-U S-812C40AY-Z2-U S-812C52AY-Z2-U S-812C59AY-Z2-U