PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Safety Recognized/High Voltage Ceramic Capacitors DEH Series (125 deg. C Guaranteed/Low-dissipation Factor/DC250V-3.15kV) Features 1. Reduced heat dissipation permitted due to small dielectric loss of the ceramic material. 2. Operating temperature range is guaranteed up to 125 degree C. 3. Coated with flame-retardant epoxy resin (equivalent to UL94V-0 standard). 4. Taping available for automatic insertion. 5. Available product for RoHS Restriction (EU Directive 2002/95/EC). T max. T max. 3.0 max. D max. 25.0 min. 25.0 min. e F1.0 od (in mm) [Bulk] Vertical Crimp Long (Fig. 1) Straight Long (Fig. 2) Lead Code Coating Extension e od Style A2, A3, A4 Up to the end of crimp 0.60.05 Fig. 1 0.60.05 Fig. 2 3.0 max. C3 Applications T max. T max. od 5.01.0 e 5.01.0 D max. 3.0 max. Ideal for use on high frequency pulse circuits such as a horizontal resonance circuit for CTV and snubber circuits for switching power supplies. F0.8 (in mm) Lead Code Coating Extension e [Bulk] Vertical Crimp Short (Fig. 1) Straight Short (Fig. 2) od Style B2, B3, B4 Up to the end of crimp 0.60.05 Fig. 1 0.60.05 Fig. 2 D3 3.0 max. Marking DC250V DC500V DC1-3.15kV R C R o6mm HR 102 66 HR 471 66 o7-9mm HR R 332K 250V 66 HR C 152K 66 HR R 102K 1KV 66 o10-21mm HR R 103K 250V 66 HR C 472K 66 HR R 272K 3KV 66 Rated Voltage Nominal Body Diameter Temp. Char. High Temperature Guaranteed Code Temperature Characteristics Nominal Capacitance Capacitance Tolerance DC250V Rated Voltage DC500V DC1-3.15kV 7 HR Marked with code (omitted for nominal body diameter o6mm) Marked with 3 figures Marked with code (omitted for nominal body diameter o6mm) Marked with code (Marked with horizontal line over nominal capacitance for nominal body diameter o6mm) Omitted Marked with code (In case of DC3.15kV, marked with 3KV) Manufacturer's Identification Marked with Manufactured Date Code Abbreviation (omitted for nominal body diameter o9mm and under) 33 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. DC250V, R Characteristics Part Number DC Rated Voltage (Vdc) Capacitance (pF) Body Dia. D (mm) Lead Spacing F (mm) Lead Body Thickness T Package (mm) Long Bulk Lead Package Short Bulk Lead Package Taping DEHR32E221Kppp 250 220 10% 6 5.0 4.0 A2B B2B N2A DEHR32E331Kppp 250 330 10% 6 5.0 DEHR32E471Kppp 250 470 10% 6 5.0 4.0 A2B B2B N2A 4.0 A2B B2B DEHR32E681Kppp 250 680 10% 6 N2A 5.0 4.0 A2B B2B DEHR32E102Kppp 250 1000 10% N2A 6 5.0 4.0 A2B B2B DEHR32E152Kppp 250 N2A 1500 10% 7 5.0 4.0 A2B B2B N2A DEHR32E222Kppp DEHR32E332Kppp 250 2200 10% 8 5.0 4.0 A2B B2B N2A 250 3300 10% 9 5.0 4.0 A2B B2B N2A DEHR32E472Kppp 250 4700 10% 10 5.0 4.0 A2B B2B N2A DEHR32E682Kppp 250 6800 10% 12 5.0 4.0 A2B B2B N2A DEHR32E103Kppp 250 10000 10% 12 5.0 4.0 A2B B2B N2A Lead Package Short Bulk Lead Package Taping Three blank columns are filled with the lead and packaging codes. Please refer to the three columns on the right for the appropriate code. DC500V, C Characteristics Part Number DC Rated Voltage (Vdc) Capacitance (pF) Body Dia. D (mm) Lead Spacing F (mm) Lead Body Thickness T Package (mm) Long Bulk DEHC32H331Kppp 500 330 10% 6 5.0 4.0 A2B B2B N2A DEHC32H471Kppp 500 470 10% 6 5.0 4.0 A2B B2B N2A DEHC32H681Kppp 500 680 10% 7 5.0 4.0 A2B B2B N2A DEHC32H102Kppp 500 1000 10% 8 5.0 4.0 A2B B2B N2A DEHC32H152Kppp 500 1500 10% 9 5.0 4.0 A2B B2B N2A DEHC32H222Kppp 500 2200 10% 10 5.0 4.0 A2B B2B N2A DEHC32H332Kppp 500 3300 10% 12 5.0 4.0 A2B B2B N2A DEHC32H472Kppp 500 4700 10% 14 10.0 4.0 A4B B4B - Lead Package Short Bulk Lead Package Taping Three blank columns are filled with the lead and packaging codes. Please refer to the three columns on the right for the appropriate code. DC1-3.15kV, R Characteristics 7 Part Number DC Rated Voltage (Vdc) Capacitance (pF) Body Dia. D (mm) Lead Spacing F (mm) Lead Body Thickness T Package (mm) Long Bulk DEHR33A221Kppp 1000 220 10% 7 5.0 4.5 A2B B2B N2A DEHR33A331Kppp 1000 330 10% 7 5.0 4.5 A2B B2B N2A DEHR33A471Kppp 1000 470 10% 7 5.0 4.5 A2B B2B N2A DEHR33A681Kppp 1000 680 10% 8 5.0 4.5 A2B B2B N2A DEHR33A102Kppp 1000 1000 10% 9 5.0 4.5 A2B B2B N2A DEHR33A152Kppp 1000 1500 10% 11 5.0 4.5 A2B B2B N2A DEHR33A222Kppp 1000 2200 10% 13 7.5 4.5 A3B B3B N3A DEHR33A332Kppp 1000 3300 10% 15 7.5 4.5 A3B B3B N7A DEHR33A472Kppp 1000 4700 10% 17 7.5 4.5 A3B B3B N7A DEHR33D221Kppp 2000 220 10% 7 7.5 5.0 C3B D3B P3A DEHR33D271Kppp 2000 270 10% 7 7.5 5.0 C3B D3B P3A DEHR33D331Kppp 2000 330 10% 8 7.5 5.0 A3B B3B N3A DEHR33D391Kppp 2000 390 10% 8 7.5 5.0 A3B B3B N3A DEHR33D471Kppp 2000 470 10% 9 7.5 5.0 A3B B3B N3A DEHR33D561Kppp 2000 560 10% 9 7.5 5.0 A3B B3B N3A DEHR33D681Kppp 2000 680 10% 10 7.5 5.0 A3B B3B N3A DEHR33D821Kppp 2000 820 10% 11 7.5 5.0 A3B B3B N3A DEHR33D102Kppp 2000 1000 10% 12 7.5 5.0 A3B B3B N3A DEHR33D122Kppp 2000 1200 10% 12 7.5 5.0 A3B B3B N3A DEHR33D152Kppp 2000 1500 10% 12 7.5 5.0 A3B B3B N3A DEHR33D182Kppp 2000 1800 10% 14 7.5 5.0 A3B B3B N7A Continued on the following page. 34 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Part Number DC Rated Voltage (Vdc) Capacitance (pF) Body Dia. D (mm) Lead Spacing F (mm) Lead Body Thickness T Package (mm) Long Bulk Lead Package Short Bulk Lead Package Taping DEHR33D222Kppp 2000 2200 10% 15 7.5 5.0 DEHR33D272Kppp 2000 2700 10% 17 7.5 5.0 A3B B3B N7A A3B B3B DEHR33D332Kppp 2000 3300 10% 19 10.0 N7A 5.0 A4B B4B DEHR33D392Kppp 2000 3900 10% 20 - 10.0 5.0 A4B B4B - DEHR33D472Kppp 2000 4700 10% DEHR33F151Kppp 3150 150 10% 21 10.0 5.0 A4B B4B - 7 7.5 6.0 C3B D3B P3A DEHR33F181Kppp 3150 DEHR33F221Kppp 3150 180 10% 7 7.5 6.0 C3B D3B P3A 220 10% 7 7.5 6.0 C3B D3B DEHR33F271Kppp P3A 3150 270 10% 7 7.5 6.0 C3B D3B P3A DEHR33F331Kppp 3150 330 10% 8 7.5 6.0 A3B B3B N3A DEHR33F391Kppp 3150 390 10% 9 7.5 6.0 A3B B3B N3A DEHR33F471Kppp 3150 470 10% 10 7.5 6.0 A3B B3B N3A DEHR33F561Kppp 3150 560 10% 10 7.5 6.0 A3B B3B N3A DEHR33F681Kppp 3150 680 10% 11 7.5 6.0 A3B B3B N3A DEHR33F821Kppp 3150 820 10% 12 7.5 6.0 A3B B3B N3A DEHR33F102Kppp 3150 1000 10% 13 7.5 6.0 A3B B3B N3A DEHR33F122Kppp 3150 1200 10% 14 7.5 6.0 A3B B3B N7A DEHR33F152Kppp 3150 1500 10% 15 7.5 6.0 A3B B3B N7A DEHR33F182Kppp 3150 1800 10% 16 7.5 6.0 A3B B3B N7A DEHR33F222Kppp 3150 2200 10% 17 7.5 6.0 A3B B3B N7A DEHR33F272Kppp 3150 2700 10% 19 10.0 6.0 A4B B4B - Three blank columns are filled with the lead and packaging codes. Please refer to the three columns on the right for the appropriate code. 7 35 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. DEH Series Specifications and Test Methods No. Item Specifications Testing Method 1 Operating Temperature Range -25 to +125C 2 Appearance and Dimensions No marked defect on appearance form and dimensions are within specified range. The capacitor should be visually inspected for evidence of defect. Dimensions should be measured with slide calipers. 3 Marking To be easily legible The capacitor should be visually inspected. No failure The capacitor should not be damaged when DC voltage of 200% of the rated voltage (DC1 to 3.15kV) or DC voltage of 250% of the rated voltage (DC250V, DC500V) is applied between the lead wires for 1 to 5 sec. (Charge/Discharge current V 50mA) No failure The capacitor is placed in the container with metal balls of diameter 1mm so that each lead wire, short circuited, is kept about 2mm off the metal balls as shown in the figure at right, and AC1250V(r.m.s.) <50/60Hz> is applied for 1 to 5 sec. between capacitor lead wires and metal balls. (Charge/Discharge current V 50mA) Between Lead Wires 4 Dielectric Strength Body Insulation Char. R [DC1 to 3.15kV], Char. C : 10000M min. Char. R [DC250V] : 1000M min. The insulation resistance should be measured with DC50050V (Char. R [DC 250V]: DC10015V) within 605 sec. of charging. Capacitance Within specified tolerance The capacitance should be measured at 20C with 10.2kHz and AC5V(r.m.s.) max. Dissipation Factor (D.F.) Char. R [DC250V] : 0.4% max. Char. R [DC1 to 3.15kV] : 0.2% max. Char. C : 0.3% max. The dissipation factor should be measured at 20C with 10.2kHz and AC5V(r.m.s.) max. 5 Insulation Resistance (I.R.) 6 7 Between Lead Wires T. C. R C 8 About 2mm Metal balls Temp. Char. -25 to +85C +85 to +125C Within 15% Within +15/-30% Within 20% The capacitance measurement should be made at each step specified in Table. Temperature Characteristics Pre-treatment : Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. before measurements. 2 3 4 5 1 Step 202 -253 202 1252 202 Temp. (C) Pull 9 Lead wire should not be cut off. Capacitor should not be broken. Strength of Lead 7 11 Vibration Resistance Appearance No marked defect Capacitance Within specified tolerance D.F. Char. R [DC250V] : 0.4% max. Char. R [DC1 to 3.15kV] : 0.2% max. Char. C : 0.3% max. Solderability of Leads W Each lead wire should be subjected to 5N (2.5N for lead diameter 0.5mm) of weight and bent 90 at the point of egress, in one direction, then returned to its original position and bent 90 in the opposite direction at the rate of one bend in 2 to 3 sec. Bending 10 As shown in the figure at right, fix the body of the capacitor and apply a tensile weight gradually to each lead wire in the radial direction of the capacitor up to 10N (5N for lead diameter 0.5mm), and keep it for 101 sec. Lead wire should be soldered with uniform coating on the axial direction over 3/4 of the circumferential direction. The capacitor should be firmly soldered to the supporting lead wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in total amplitude, with about a 1 minute rate of vibration change from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs., 2 hrs. each in 3 mutually perpendicular directions. The lead wire of a capacitor should be dipped into a ethanol solution of 25wt% rosin and then into molten solder for 20.5 sec. In both cases the depth of dipping is up to about 1.5 to 2mm from the root of lead wires. Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 2455C H63 Eutectic Solder 2355C * "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa Continued on the following page. 36 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. DEH Series Specifications and Test Methods Continued from the preceding page. No. 12 13 14 15 Item Soldering Effect (Non-Preheat) Soldering Effect (On-Preheat) Specifications Appearance No marked defect Capacitance Change Within 10% Dielectric Strength (Between Lead Wires) Per item 4. Appearance No marked defect Capacitance Change Within 10% Dielectric Strength (Between Lead Wires) Per item 4. Appearance No marked defect Capacitance Change Within 10% D.F. 0.4% max. I.R. 1000M min. Temperature Cycle Humidity (Under Steady State) Dielectric Strength (Between Lead Wires) Per item 4. Appearance No marked defect Capacitance Change Within 10% D.F. 0.4% max. I.R. 1000M min. Testing Method The lead wire should be immersed into the melted solder of 35010C up to about 1.5 to 2mm from the main body for 3.50.5 sec. Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored for 242 hrs. at *room condition. Measurement order: Dielectric strength -> Pre-treatment -> Capacitance -> Soldering effect test -> Post-treatment -> Capacitance * Dielectric strength (Char. R [DC250V]) First the capacitor should be , Capacitor Thermal stored at 120+0/-5C for Screen, , 60+0/-5 sec. , , 1.5 ,,,,,,,,,, , ,,,,,, Then, as in figure, the lead wires ,,,,,,,,,, ,,,, , to 2.0mm , , should be immersed solder of ,,,Molten 260+0/-5C up to 1.5 to 2.0mm Solder from the root of terminal for 7.5+0/-1 sec. Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored for 242 hrs. at *room condition. Measurement order: Dielectric strength -> Pre-treatment -> Capacitance -> Soldering effect test -> Post-treatment -> Capacitance * Dielectric strength (Char. R [DC250V]) The capacitor should be subjected to 5 temperature cycles. Step 1 2 3 4 Temperature (C) Time (min) -253 30 Room Temp. 3 1253 30 Room Temp. 3 Cycle time: 5 cycle Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored for 242 hrs. at *1room condition. Measurement order: I.R. * Dielectric strength -> Pre-treatment -> Capacitance * D.F. -> Temperature cycle test -> Post-treatment -> Capacitance * D.F. * I.R. * Dielectric strength (Char. R [DC250V]) Set the capacitor for 500 +24/-0 hrs. at 402C in 90 to 95% relative humidity. Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored for 1 to 2 hrs. at *1room condition. Measurement order: I.R. -> Pre-treatment -> Capacitance * D.F. -> Humidity test -> Post-treatment -> Capacitance * D.F. * I.R. (Char. R [DC250V]) *1 "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa Continued on the following page. 37 7 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note C85E.pdf 06.6.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. DEH Series Specifications and Test Methods Continued from the preceding page. No. 16 17 Item Specifications Appearance No marked defect Capacitance Change Within 10% D.F. 0.6% max. I.R. 1000M min. Appearance No marked defect Capacitance Change Within 10% D.F. 0.4% max. I.R. Char. R [DC1 to 3.15kV], Char. C : 2000M min. Char. R [DC250V] : 1000M min. Humidity Loading Life Testing Method Apply the rated voltage for 500 +24/-0 hrs. at 402C in 90 to 95% relative humidity. (Charge/Discharge currentV50mA) Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored for 1 to 2 hrs. at *1room condition. (Char. R [DC1 to 3.15kV], Char. C) Post-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. (Char. R [DC250V]) Measurement order: I.R. -> Pre-treatment -> Capacitance * D.F. -> Humidity loading test -> *2 I.R. -> Post-treatment -> Capacitance * D.F. (Char. R [DC250V]) Apply a DC voltage of 200% of the rated voltage (DC250V, DC500V) or DC voltage of 150% of the rated voltage (DC1 to 3.15kV) for 1000 +48/-0 hrs. at 1252C with a relative humidity of 50% max. (Charge/Discharge currentV50mA) Pre-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. before initial measurements. Post-treatment: Capacitor should be stored at 1253C for 1 hr., then placed at *1room condition for 242 hrs. Measurement order: I.R. -> Pre-treatment -> Capacitance * D.F. -> Life test -> *3I.R. -> Post-treatment -> Capacitance * D.F. (Char. R [DC250V]) *1 "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa *2 The measurement of I.R. will be held in 1 to 2 hrs. after Humidity loading test. *3 The measurement of I.R. will be held in 12 to 24 hrs. after Life test. 7 38