CYD04S36V18-200BBC - Cypress Semiconductor Corp.

FullFlex™ Synchronous SDR Dual Port SRAM

FullFlex

Cypress Semiconductor Corporation • 198 Champion Court • San Jose,CA 95134-1709 • 408-943-2600

Document Number: 38-06082 Rev. *H Revised May 15, 2008

Features

■True dual port memory enables simultaneous access to the

shared array from each port

■Synchronous pipelined operation with Single Data Rate (SDR)

operation on each port

❐SDR interface at 200 MHz

❐Up to 28.8 Gb/s bandwidth (200 MHz x 72 bit x 2 ports)

■Selectable pipelined or flow-through mode

■1.5V or 1.8V core power supply

■Commercial and Industrial temperature

■IEEE 1149.1 JTAG boundary scan

■Available in 484-Ball PBGA (x72) and 256-Ball FBGA (x36 and

x18) packages

■FullFlex72 fami ly

❐36 Mbit: 512K x 72 (CYD36S72V18)

❐18 Mbit: 256K x 72 (CYD18S72V18)

❐9 Mbit: 128K x 72 (CYD09S72V18)

❐4 Mbit: 64K x 72 (CYD04S72V18)

■FullFlex36 fami ly

❐36 Mbit: 1M x 36 (CYD36S36V18)

❐18 Mbit: 512K x 36 (CYD18S36V18)

❐9 Mbit: 256K x 36 (CYD09S36V18)

❐4 Mbit: 128K x 36 (CYD04S36V18)

❐2 Mbit: 64K x 36 (CYD02S36V18)

■FullFlex18 fami ly

❐36 Mbit: 2M x 18 (CYD36S18V18)

❐18 Mbit: 1M x 18 (CYD18S18V18)

❐9 Mbit: 512K x 18 (CYD09S18V18)

❐4 Mbit: 256K x 18 (CYD04S18V18)

■Built in deterministic access control to manage ad dress colli-

sions

❐Deterministic flag output upon collision detection

❐Collision detection on back-to-back clock cycles

❐First Busy Address readback

■Advanced features for improved high speed data transfer and

flexibility

❐Variable Impedance Matching (VIM)

❐Echo clocks

❐Selectable LVTTL (3.3V), Extended HSTL (1.4V–1.9V), 1.8V

LVCMOS, or 2.5V LVCMOS IO on each port

❐Burst counters for sequential memory access

❐Mailbox with interrupt flags for message passing

❐Dual Chip Enables for easy de pth expansion

Functional Description

The FullFlex™ dual port SRAM families consist of 2 Mbit, 4 Mbit,

9 Mbit, 18 Mbit, and 36 Mbit synchronous, true dual port static

RAMs that are high speed, low power 1.8V or 1.5V CMOS. Two

ports are provided, enabling simultaneous access to the array.

Simultaneous access to a location triggers deterministic access

control. For FullFlex72 these ports operate independently with

72-bit bus widths and each po rt is independ ently configured for

two pipelined stages. Each port is also configured to operate in

pipelined or flow through mode.

The advanced features include the following:

■Built in deterministic access control to manage address colli-

sions during simultaneous access to the same memory location

■Variable Impedance Matching (VIM) to improve data trans-

mission by matching the output driver impedance to the line

impedance

■Echo clocks to improve data transfer

To reduce the static power consumption, chip enables power

down the internal circuitry. The number of latency cycles before

a change in CE0 or CE1 enables or disables the databus

matches the number of cycles of read latency selected for the

device. For a valid write or read to occur, activate both chip

enable inputs on a port.

Each port contains an optional burst counter on the input address

address, the counter increments the address internally.

Additional device features include a mask re gister and a mirror

counter interrupt (CNTINT) flags notify the ho st that the counter

reaches maximum count value on the next clock cycle. The host

reads the burst counter internal address, mask register address,

and busy address on the address lines. The host also loads the

counter with the address stored in the mirror register by using the

retransmit functionality. Mailbox interrupt flags are used for

message passing, and JTAG boundary scan and asynchronous

Master Reset (MRST) are also available. The Logic Block

Diagram on page 2 shows these features.

The FullFlex72 is offered in a 484-Ball plastic BGA package. The

FullFlex36 and FullFlex18 are available in 256-Ball fine pitch

BGA package.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 2 of 52

Logic Block Diagram

The Logic Block Diagram for FullFlex72, FullFlex36, and FullFlex18 family follows: [1, 2, 3]

FTSEL

PORTSTD[1:0]

DQ[71:0]

[7:0]L

FTSEL

PORTSTD[1:0]

DQ [71:0]

[7:0]R

CE1

A [20:0]

CNT/

MSKL

ADS

CNTEN

CNTRST

RET

CNTINT

WRP

A [20:0]

CNT/

MSKR

ADS

CNTEN

CNTRST

RET

CNTINT

WRP

CONFIG Block CONFIG Block

Control IO

Control

Address &

Counter Logic Address &

Counter Logic

INT

TRST

TMS

TDI

TDO

TCK

JTAG

MRST

READY

LowSPD

READY

LowSPD

RESET

LOGIC

INT

BUSY

Mailboxes

Collision Detection Logic

Dual Port Array

CQEN

CE1

CQ1

CQ0

CQ1

ZQ0

ZQ1

ZQ0

ZQ1

Notes

1. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and

CYD09S18V18 devices have 19 address bits. The CYD18S72V18, CYD09S36V18, and CYD04S18V18 devices have 18 address bits. The CYD09S72V18 and

CYD04S36V18 devices have 17 address bits. The CYD04S72V18 and CYD02S36V18 have 16 address bits.

2. The FullFlex72 family of devices has 72 data lines. The FullFlex36 family of devices has 36 data lines. The FullFlex18 family of devices has 18 data lines.

3. The FullFlex72 family of devices has eigh t byte enables. The FullFlex36 family of de vices has four byte enables. The FullFlex18 family of devices has two byte enable s.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 3 of 52

Figure 1. FullFlex72 SDR 484-Ball BGA Pinout (Top View)

12345678910111213141516171819

20 21 22

ADNU DQ61L DQ59L DQ57L DQ54L DQ51L DQ48L DQ45L DQ42L DQ39L DQ36L DQ36R DQ39R DQ42R DQ45R DQ48R DQ51R DQ54R DQ57R DQ59R DQ61R DNU

BDQ63L DQ62L DQ60L DQ58L DQ55L DQ52L DQ49L DQ46L DQ43L DQ40L DQ37L DQ37R DQ40R DQ43R DQ46RDQ49RDQ52RDQ55RDQ58RDQ60RDQ62RDQ63R

CDQ65L DQ64L VSS VSS DQ56L DQ53L DQ50L DQ47L DQ44L DQ41L DQ38L DQ38R DQ41R DQ44R DQ47R DQ50R DQ53R DQ56R VSS VSS DQ64R DQ65R

DDQ67L DQ66L VSS VSS VSS CQ1L CQ1L VSS LOWS

PDL PORTS

TD0L ZQ0L

[4] BUSYL CNTIN

TL PORTS

TD1L DNU CQ1R CQ1R VSS VSS VSS DQ66R DQ67R

EDQ69L DQ68L VDDIO

LVSS VSS VDDIO

LVDDIO

LVTTL VTTL VTTL VDDIO

RVDDIO

RDNU VSS VDDIO

RDQ68R DQ69R

FDQ71L DQ70L CE1L CE0L VDDIO

LVDDIO

LVCOR

EVCOR

EVDDIO

RVDDIO

RCE0R CE1R DQ70R DQ71R

GA0L A1L RETL BE4L VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RBE4R RETR A1R A0R

HA2L A3L WRPL BE5L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE5R WRPR A3R A2R

JA4L A5L READY

LBE6L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE6R READY

RA5R A4R

KA6L A7L ZQ1L

[4, 5] BE7L VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVDDIO

RBE7R ZQ1R

[4, 5] A7R A6R

LA8L A9L CL OEL VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL OER CR A9R A8R

MA10L A11L VSS BE3L VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL BE3R VSS A11R A10R

NA12L A13L ADSL BE2L VDDIO

LVCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL BE2R ADSR A13R A12R

PA14L A15L CNT/M

SKL BE1L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE1R CNT/M

SKR A15R A14R

RA16L

[8] A17L

[7] CNTEN

LBE0L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE0R CNTEN

RA17R

[7] A16R

[8]

TA18L

[6] DNU CNTRS

TL INTL VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RINTR CNTRS

TR DNU A18R

[6]

UDQ35L DQ34L R/WL CQENL VDDIO

LVDDIO

LVCOR

EVCOR

EVDDIO

RVDDIO

RCQEN

RR/WR DQ34R DQ35R

VDQ33L DQ32L FTSEL

LVDDIO

LDNU VDDIO

LVDDIO

LVTTL VTTL VTTL VDDIO

RVDDIO

RTRST VDDIO

RFTSEL

RDQ32R DQ33R

WDQ31L DQ30L VSS MRST VSS CQ0L CQ0L DNU PORTS

TD1R CNTIN

TR BUSYR ZQ0R

[4] PORTS

TD0R LOWS

PDR VSS CQ0R CQ0R VSS TDI TDO DQ30R DQ31R

YDQ29L DQ28L VSS VSS DQ20L DQ17L DQ14L DQ11L DQ8L DQ5L DQ2L DQ2R DQ5R DQ8R DQ11R DQ14R DQ17R DQ20R TMS TCK DQ28R DQ29R

AA DQ27L DQ26L DQ24L DQ22L DQ19L DQ16L DQ13L DQ10L DQ7L DQ4L DQ1L DQ1R DQ4R DQ7R DQ10R DQ13R DQ16R DQ19R DQ22R DQ24R DQ26R DQ27R

AB DNU DQ25L DQ23L DQ21L DQ18L DQ15L DQ12L DQ9L DQ6L DQ3L DQ0L DQ0R DQ3R DQ6R DQ9R DQ12RDQ15RDQ18RDQ21RDQ23RDQ25R DNU

Notes

4. Leave this ball unconnected to disabl e VIM.

5. This ball is applicable only for 36 Mbit and DNU for 18 Mbit and lower densities.

6. Leave this Ball unconnected for CYD18S72V18, CYD09S72V1 8, and CYD04S72V18.

7. Leave this Ball unconnected for CYD09S72V18 and CYD04S72V18.

8. Leave this Ball unconnected for CYD04S72V18.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 4 of 52

Figure 2. FullFlex36 SDR 484-Ball BGA Pinout (Top View)[9]

12345678910111213141516171819202122

ADNU DNU DNU DNU DNU DQ33L DQ30L DQ27L DQ24L DQ21L DQ18L DQ18R DQ21R DQ24R DQ27R DQ30R DQ33R DNU DNU DNU DNU DNU

BDNU DNU DNU DNU DNU DQ34L DQ31L DQ28L DQ25L DQ22L DQ19L DQ19R DQ22R DQ25R DQ28R DQ31R DQ34R DNU DNU DNU DNU DNU

CDNU DNU VSS VSS DNU DQ35L DQ32L DQ29L DQ26L DQ23L DQ20L DQ20R DQ23R DQ26R DQ29R DQ32R DQ35R DNU VSS VSS DNU DNU

DDNU DNU VSS VSS VSS CQ1L CQ1L VSS LOWS

PDL PORTS

TD0L ZQ0L

[4] BUSYL CNTIN

TL PORTS

TD1L DNU CQ1R CQ1R VSS VSS VSS DNU DNU

EDNU DNU VDDIO

LVSS VSS VDDIO

LVDDIO

RVDDIO

RVTTL VTTL VTTL VDDIO

LVDDIO

LDNU VSS VDDIO

RDNU DNU

FDNU DNU CE1L CE0L VDDIO

LVDDIO

RVDDIO

RVCOR

EVCOR

EVDDIO

LVDDIO

RVDDIO

RCE0R CE1R DNU DNU

GA0L A1L RETL BE2L VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RBE2R RETR A1R A0R

HA2L A3L WRPL BE3L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE3R WRPR A3R A2R

JA4L A5L READY

LDNU VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RDNU READY

RA5R A4R

KA6L A7L ZQ1L

[4] DNU VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVDDIO

RDNU ZQ1R

[4] A7R A6R

LA8L A9L CL OEL VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL OER CR A9R A8R

MA10L A11L VSS DNU VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL DNU VSS A11R A10R

NA12L A13L ADSL DNU VDDIO

LVCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL DNU ADSR A13R A12R

PA14L A15L CNT/M

SKL BE1L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE1R CNT/M

SKR A15R A14R

RA16L A17L CNTEN

LBE0L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE0R CNTEN

RA17R A16R

TA18L A19L CNTRS

TL INTL VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RINTR CNTRS

TR A19R A18R

UDNU DNU R/WL CQENL VDDIO

LVDDIO

RVDDIO

RVCOR

EVCOR

EVDDIO

LVDDIO

RVDDIO

RCQEN

RR/WR DNU DNU

VDNU DNU FTSEL

LVDDIO

LDNU VDDIO

RVDDIO

RVTTL VTTL VTTL VDDIO

LVDDIO

RTRST VDDIO

RFTSEL

RDNU DNU

WDNU DNU VSS MRST VSS CQ0L CQ0L DNU PORTS

TD1R CNTIN

TR BUSYR ZQ0R

[4] PORTS

TD0R LOWS

PDR VSS CQ0R CQ0R VSS TDI TDO DNU DNU

YDNU DNU VSS VSS DNU DQ17L DQ14L DQ11L DQ8L DQ5L DQ2L DQ2R DQ5R DQ8R DQ11R DQ14R DQ17R DNU TMS TCK DNU DNU

AA DNU DNU DNU DNU DNU DQ16L DQ13L DQ10L DQ7L DQ4L DQ1L DQ1R DQ4R DQ7R DQ10R DQ13R DQ16R DNU DNU DNU DNU DNU

AB DNU DNU DNU DNU DNU DQ15L DQ12L DQ9L DQ6L DQ3L DQ0L DQ0R DQ3R DQ6R DQ9R DQ12R DQ15R DNU DNU DNU DNU DNU

Note

9. Use this pinout only for device CYD36S36V18 of the FullFlex36 family.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 5 of 52

Figure 3. FullFlex 1 8 SDR 484-Ball BGA Pino ut (Top View)[10]

12345678910111213141516171819202122

ADNU DNU DNU DNU DNU DNU DNU DNU DQ15L DQ12L DQ9L DQ9R DQ12R DQ15R DNU DNU DNU DNU DNU DNU DNU DNU

BDNU DNU DNU DNU DNU DNU DNU DNU DQ16L DQ13L DQ10L DQ10R DQ13R DQ16R DNU DNU DNU DNU DNU DNU DNU DNU

CDNU DNU VSS VSS DNU DNU DNU DNU DQ17L DQ14L DQ11L DQ11R DQ14R DQ17R DNU DNU DNU DNU VSS VSS DNU DNU

DDNU DNU VSS VSS VSS CQ1L CQ1L VSS LOWS

PDL PORTS

TD0L ZQ0L

[4] BUSYL CNTIN

TL PORTS

TD1L DNU CQ1R CQ1R VSS VSS VSS DNU DNU

EDNU DNU VDDIO

LVSS VSS VDDIO

LVDDIO

RVDDIO

RVTTL VTTL VTTL VDDIO

LVDDIO

LDNU VSS VDDIO

RDNU DNU

FDNU DNU CE1L CE0L VDDIO

LVDDIO

RVDDIO

RVCOR

EVCOR

EVDDIO

LVDDIO

RVDDIO

RCE0R CE1R DNU DNU

GA0L A1L RETL BE1L VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RBE1R RETR A1R A0R

HA2L A3L WRPL DNU VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RDNU WRPR A3R A2R

JA4L A5L READY

LDNU VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RDNU READY

RA5R A4R

KA6L A7L ZQ1L

[4] DNU VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVDDIO

RDNU ZQ1R

[4] A7R A6R

LA8L A9L CL OEL VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL OER CR A9R A8R

MA10L A11L VSS DNU VTTL VCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL DNU VSS A11R A10R

NA12L A13L ADSL DNU VDDIO

LVCOR

EVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VCOR

EVTTL DNU ADSR A13R A12R

PA14L A15L CNT/M

SKL DNU VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RDNU CNT/M

SKR A15R A14R

RA16L A17L CNTEN

LBE0L VDDIO

LVDDIO

LVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDDIO

RVDDIO

RBE0R CNTEN

RA17R A16R

TA18L A19L CNTRS

TL INTL VDDIO

LVDDIO

LVREFL VSS VSS VSS VSS VSS VSS VSS VSS VREFR VDDIO

RVDDIO

RINTR CNTRS

TR A19R A18R

UA20L DNU R/WL CQENL VDDIO

LVDDIO

RVDDIO

RVCOR

EVCOR

EVDDIO

LVDDIO

RVDDIO

RCQEN

RR/WR DNU A20R

VDNU DNU FTSEL

LVDDIO

LDNU VDDIO

RVDDIO

RVTTL VTTL VTTL VDDIO

LVDDIO

RTRST VDDIO

RFTSEL

RDNU DNU

WDNU DNU VSS MRST VSS CQ0L CQ0L DNU PORTS

TD1R CNTIN

TR BUSYR ZQ0R

[4] PORTS

TD0R LOWS

PDR VSS CQ0R CQ0R VSS TDI TDO DNU DNU

YDNU DNU VSS VSS DNU DNU DNU DNU DQ8L DQ5L DQ2L DQ2R DQ5R DQ8R DNU DNU DNU DNU TMS TCK DNU DNU

AA DNU DNU DNU DNU DNU DNU DNU DNU DQ7L DQ4L DQ1L DQ1R DQ4R DQ7R DNU DNU DNU DNU DNU DNU DNU DNU

AB DNU DNU DNU DNU DNU DNU DNU DNU DQ6L DQ3L DQ0L DQ0R DQ3R DQ6R DNU DNU DNU DNU DNU DNU DNU DNU

Note

10.Use this pinout only for device CYD36S18V18 of the FullFlex18 family.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 6 of 52

Figure 4. FullFlex36 SDR 256-Ball BGA (Top View)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

ADQ32L DQ30L DQ28L DQ26L DQ24L DQ22L DQ20L DQ18L DQ18R DQ20R DQ22R DQ24R DQ26R DQ28R DQ30R DQ32R

BDQ33L DQ31L DQ29L DQ27L DQ25L DQ23L DQ21L DQ19L DQ19R DQ21R DQ23R DQ25R DQ27R DQ29R DQ31R DQ33R

CDQ34L DQ35L RETL INTL CQ1L CQ1L DNU TRST MRST ZQ0R[4] CQ1R CQ1R INTR RETR DQ35R DQ34R

DA0L A1L WRPL VREFL FTSELL LOWSPDL VSS VTTL VTTL VSS LOWSPD

RFTSELR VREFR WRPR A1R A0R

EA2L A3L CE0L CE1L VDDIOL VDDIOL VDDIOL VCORE VCORE VDDIOR VDDIOR VDDIOR CE1R CE0R A3R A2R

FA4L A5L CNTINTL BE3L VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR BE3R CNTINTR A5R A4R

GA6L A7L BUSYL BE2L ZQ0L[4] VSS VSS VSS VSS VSS VSS VDDIOR BE2R BUSYR A7R A6R

HA8L A9L CL VTTL VCORE VSS VSS VSS VSS VSS VSS VCORE VTTL CR A9R A8R

JA10L A11L VSS PORTSTD

1L VCORE VSS VSS VSS VSS VSS VSS VCORE PORTSTD

1R VSS A11R A10R

KA12L A13L OEL BE1L VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR BE1R OER A13R A12R

LA14L A15L ADSL BE0L VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR BE0R ADSR A15R A14R

MA16L[13] A17L[12] R/WL CQENL VDDIOL VDDIOL VDDIOL VCORE VCORE VDDIOR VDDIOR VDDIOR CQENR R/WR A17R[12] A16R[13]

NA18L[11] DNU CNT/MSK

LVREFL PORTSTD

0L READYL DNU VTTL VTTL DNU READYR PORTSTD

0R VREFR CNT/MSK

RDNU A18R[11]

PDQ16L DQ17L CNTENL CNTRSTL CQ0L CQ0L TCK TMS TDO TDI CQ0R CQ0R CNTRSTR CNTENR DQ17R DQ16R

RDQ15L DQ13L DQ11L DQ9L DQ7L DQ5L DQ3L DQ1L DQ1R DQ3R DQ5R DQ7R DQ9R DQ11R DQ13R DQ15R

TDQ14L DQ12L DQ10L DQ8L DQ6L DQ4L DQ2L DQ0L DQ0R DQ2R DQ4R DQ6R DQ8R DQ10R DQ12R DQ14R

Notes

11. Leave this ball unconnected for CYD0 9S36V18, CYD04S36V18, and CYD02S36V18.

12.Leave this ball unconnected for CYD04S36V18 and CYD02S36V18.

13.Leave this ball unconnected for CYD02S36V18.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 7 of 52

Figure 5. FullFlex18 SDR 256-Ball BGA (Top View)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

ADNU DNU DNU DQ17L DQ16L DQ13L DQ12L DQ9L DQ9R DQ12R DQ13R DQ16R DQ17R DNU DNU DNU

BDNU DNU DNU DNU DQ15L DQ14L DQ11L DQ10L DQ10R DQ11R DQ14R DQ15R DNU DNU DNU DNU

CDNU DNU RETL INTL CQ1L CQ1L DNU TRST MRST ZQ0R[4] CQ1R CQ1R INTR RETR DNU DNU

DA0L A1L WRPL VREFL FTSELL LOWSPDL VSS VTTL VTTL VSS LOWSPD

RFTSELR VREFR WRPR A1R A0R

EA2L A3L CE0L CE1L VDDIOL VDDIOL VDDIOL VCORE VCORE VDDIOR VDDIOR VDDIOR CE1R CE0R A3R A2R

FA4L A5L CNTINTL DNU VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR DNU CNTINTR A5R A4R

GA6L A7L BUSYL DNU ZQ0L[4] VSS VSS VSS VSS VSS VSS VDDIOR DNU BUSYR A7R A6R

HA8L A9L CL VTTL VCORE VSS VSS VSS VSS VSS VSS VCORE VTTL CR A9R A8R

JA10L A11L VSS PORTSTD

1L VCORE VSS VSS VSS VSS VSS VSS VCORE PORTSTD

1R VSS A11R A10R

KA12L A13L OEL BE1L VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR BE1R OER A13R A12R

LA14L A15L ADSL BE0L VDDIOL VSS VSS VSS VSS VSS VSS VDDIOR BE0R ADSR A15R A14R

MA16L A17L R/WL CQENL VDDIOL VDDIOL VDDIOL VCORE VCORE VDDIOR VDDIOR VDDIOR CQENR R/WR A17R A16R

NA18L[15] A19L[14] CNT/MSK

LVREFL PORTSTD

0L READYL DNU VTTL VTTL DNU READYR PORTSTD

0R VREFR CNT/MSK

RA19R[14] A18R[15]

PDNU DNU CNTENL CNTRSTL CQ0L CQ0L TCK TMS TDO TDI CQ0R CQ0R CNTRSTR CNTENR DNU DNU

RDNU DNU DNU DNU DQ6L DQ5L DQ2L DQ1L DQ1R DQ2R DQ5R DQ6R DNU DNU DNU DNU

TDNU DNU DNU DQ8L DQ7L DQ4L DQ3L DQ0L DQ0R DQ3R DQ4R DQ7R DQ8R DNU DNU DNU

Notes

14.Leave this ball unconnected for CYD09S18V18 and CYD04S18V18.

15.Leave this ball unconnected for CYD04S18V18.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 8 of 52

Selection Guide

Parameter –200 –167 Unit

fMAX[17] 200 167 MHz

Maximum Access T ime (Clock to Data ) 3.3 4.0 ns

Typical Operating Current ICC 800[16] 700[16] mA

Typical Standby Current for ISB3 (Both Ports CMOS Level) 210[16] 210[16] mA

Pin Definitions

Left Port Right Port Description

A[20:0]LA[20:0]RAddress Inputs.[1]

DQ[71:0]LDQ[71:0]RData Bus Input and Output.[2]

BE[7:0]LBE[7:0]RByte Select Inputs.[3] Asserting these signals enables read and write operations to the corresponding

bytes of the memory array.

BUSYLBUSYRPort Busy Output. When there is an address match and both chip enables are active for both ports,

an external BUSY signal is asserted on the fifth clock cycles from when the collision occurs.

CLCRClock Signal. Maximum clock input rate is fMAX.

CE0LCE0RActive LOW Chip Enable Input.

CE1LCE1RActive HIGH Chip Enable Input.

CQENLCQENREcho Clock Enable Input. Assert HIGH to enable echo clocking on respective port.

CQ0LCQ0REcho Clock Signal Output for DQ[35:0] for FullFlex72 Devices. Echo Clock Signal Output for

DQ[17:0] for FullFlex36 devices. Echo Clock Signal Output for DQ[8:0] for FullFlex18 devices.

CQ0LCQ0RInverted Echo Cl ock Signal Output for DQ[35:0] for FullFlex72 Devices. Inverted Echo Clock

Signal Output for DQ[17:0] for FullFlex36 devices. Inverted Echo Clock Signal Output for DQ[8:0] for

FullFlex18 devices.

CQ1LCQ1REcho Clock Signal Output for DQ[71:36] for FullFlex72 Devices. Echo Clock Signal Output for

DQ[35:18] for FullFlex36 devices. Echo Clock Signal Output for DQ[17:9] for FullFlex18 devices.

CQ1LCQ1RInverted Echo Clock Signal Output for DQ[71:36] for FullFlex72 Devices. Inverted Echo Clock

Signal Output for DQ[35:18] for FullFlex36 devices. Inverted Echo Clock Signal Output for DQ[17:9]

forFullFlex18 devices.

ZQ[1:0]LZQ[1:0]RVIM Output Impedance Matching Input.[18] To use, connect a calibrating resistor between ZQ and

ground. The resistor must be five times larger than the intended line impedance driven by the dual

port. Assert HIGH or leave DNU to disable VIM.

OELOEROutput Enable Input. This asynchronous signal must be asserted LOW to enable the DQ data pins

during read operations.

INTLINTRMailbox Interrupt Flag Output. The mailbox permits communications between ports. The upper two

memory locations are used for message passing. INTL is asserted LOW when the right port writes to

the mailbox location of the left port, and vice versa. An interrupt to a port is deasserted HIGH when

it reads the contents of its mailbox.

LowSPDLLowSPDRPort Low Speed Select Input. Assert this pin LOW to disable the DLL . Fo r operation at less than

100 MHz, assert this pin LOW.

Notes

16.For 18 Mbit x72 commercial configuration only, refer to Electrical Characteristics on page 18 for complete information.

17.SDR mode with two pipelined stages.

18.The pin ZQ[1] is applicable only for 36 Mbit devices. This pin is DNU for 18 Mbit and lower density devices.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 9 of 52

PORTSTD[1:0]

L[19] PORTSTD[1:0]

R[19] Port Clock/Address/Control/Data/Echo Clock/I/O Standard Select Input. Assert these pins

LOW/LOW for L VTTL, LOW/HIGH for HSTL, HIGH/LOW for 2.5V L VCMOS, and HIGH/HIGH for 1.8V

LVCMOS, respectively. These pins are driven by VTTL referenced levels.

R/WLR/WRRead/Write Enable Input. Assert this pin LOW to write to, or HIGH to read from the dual port memory

array.

READYLREADYRPort DLL Ready Output. This signal is asse rted LOW when the DLL and Variable Impedance

Matching circuits complete calibration. This is a wired OR capable output.

CNT/MSKLCNT/MSKRPort Counter/Mask Select Input. Counter control input.

ADSLADSRPort Counter Address Load Strobe Input. Counter control input.

CNTENLCNTENRPort Counter Enable Input. Counter control in p ut .

CNTRSTLCNTRSTRPort Counter Reset Input. Counter control input.

CNTINTLCNTINTRPort Counter Interrupt Output. This pin is asserted LOW one cycle before the unmasked portion

of the counter is incremented to all “1s”.

WRPLWRPRPort Counter Wrap Input. When the burst counter reaches the maximum count, on the next counter

increment WRP is set LOW to load the unmasked counter bits to 0. It is set HIGH to load the counter

with the value stored in the mirror register.

RETLRETRPort Counter Retransmit Input. Assert this pin LOW to reload the initial address for repeated access

to the same segment of memory.

VREFLVREFRPort External HSTL IO Reference Input. This pin is left DNU when HSTL is not used.

VDDIOLVDDIORPort Data IO Power Supply.

FTSELLFTSELRPort Flow through Mode Select Input. Assert this pin LOW to select Flow th rough mode. Assert

this pin HIGH to select Pipelined mode.

MRST Master Reset Input. MRST is an asynchronous input signal and affect s both ports. Asserting MRST

LOW performs all of the reset functions as described in the text. A MRST operation is required at

power up. This pin is driven by a VDDIOL referenced signal.

TMS JTAG Test Mode Select Input. It controls the advance of JTAG TAP state machine. State machine

transitions occur on the rising edge of TCK. Operati on for LVTTL or 2.5V LV CMOS.

TDI JTAG Test Data Input. Data on the TDI input is shifted serially into selected registers. Operation for

LVTTL or 2.5V LVCMOS.

TRST JTAG Reset Input. Operation for LVTTL or 2.5V LVCMOS.

TCK JTAG Test Clock Input. Operation for LVTTL or 2.5V LVCMOS.

TDO JT AG T est Data Output. TDO transitions occur on the falling edge of TCK. TDO is normally tri-stated

except when captured data is shifted out of the JTAG TAP. Operation for LV T TL or 2.5V LVCMOS.

VSS Ground Inputs.

VCORE Device Core Power Supply.

VTTL LVTTL Power Supply.

Pin Definitions (continued)

Left Port Right Port Description

Note

19.PORTSTD[1:0]L and PORTSTD[1:0]R have internal pull down resistors.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 10 of 52

Selectable IO Standard

The FullFlex device families offer the option to choose one of the

four port standards for the device. Each port independently

selects standards from single ended HSTL class I, single ended

LVTTL, 2.5V LVCMOS, or 1.8V LVCMOS. The selection of the

standard is determined by the PORTSTD pins for each port.

These pins must be connected to an LVTTL power suppy. This

determines the input clock, address, control, data, and Echo

clock standard for each port as shown in Table 1.

Clocking

Separate clocks synchronize the operations on each port. Each

port has one clock input C. In this mode, all the transactions on

the address, control, and data are on the C rising edge. All trans-

actions on the address, control, data input, output, and byte

enables occur on the C rising edge.

Selectable Pipelined or Flow th rough Mode

To meet data rate and throughput requirements, the FullFlex

families offer selectable pipelined or flow through mode. Echo

clocks are not supported in flow through mode and the DLL must

be disabled.

Flow through mode is selected by the FTSEL pin. Strapping this

pin HIGH selects pipelined mode. S trapping this pin LOW selects

flow through mode.

DLL

The FullFlex familes of devices have an on-chip DLL. Enabling

the DLL reduces the clock to data valid (tCD) time enabling more

setup time for the receiving device. For operation below

100 MHz, the DLL must be disabled. This is selectable by

strapping LowSPD low.

Whenever the operatin g frequency is altered beyond the Clock

Input Cycle to Cycle Jitter specification, reset the DLL, followed

by 1024 clocks before any valid operation.

LowSPD pins are used to reset the DLLs for a single port

independent of all other circuitry . MRST is used to reset all DLLs

on the chip. For more information on DLL lock and reset time,

see Master Reset on page 17 .

Echo Clocking

As the speed of data increases, on-board delays caused by

parasitics make it extremely difficult to provide accurate clock

trees. To counter this problem, the FullFlex families incorporate

Echo Clocks. Echo Clocks are enabled on a per port basis. The

dual port receives input clocks that are used to clock in the

address and control signals fo r a read operation. The dual port

retransmits the input clocks relative to the data output. The

buffered clocks are provided on the CQ1/CQ1 and CQ0/CQ0

outputs. Each port has a pair of Echo clocks. Each clock is

associated with half the data bits. The output clock matches the

corresponding ports IO configuration.

To enable echo clock outp uts, tie CQEN HIGH. To disab le echo

clock outputs, tie CQEN LOW.

Deterministic Access Control

Deterministic Access Control is provided for ease of design. The

circuitry detects when both ports access the same location and

provides an external BUSY flag to the port on which data is

corrupted. The collision detection logic saves the address in

conflict (Busy Address) to a readable register. In the case of

multiple collisions, the first busy address is written to the busy

address register.

If both ports access the same location at the same time and only

one port is doing a write, if tCCS is met, then the data writt en to

and read from the address is valid data. For example, if the right

port is reading an d the left port is writing and the left ports clock

meets tCCS, then the data read from the address by the right port

is the old data. In the same case, i f the right ports clock meets

tCCS, then the data read out of the address from the right port is

the new data. In the above case, if tCCS is violated by the either

ports clock with respect to the other port and the right port gets

the external BUSY flag, the data from the right port is corrupted.

Table 3 on page 11 shows the tCCS timing that must be met to

guarantee the data.

Table 4 on page 11 shows that, in the case of the left port writing

and the right port reading, when an external BUSY flag is

asserted on the right port, the data read out of the device is not

guaranteed.

The value in the busy address register is read back to the

address lines. The required input control signals for this function

are shown in Table 7 on page 13. The value in the busy address

amount of latency as a data read operation. After an initial

address match, the BUSY flag is asserted and the address under

contention is saved in the busy address register . All the following

Table 1. Port Standard Selection

PORTSTD1 PORTSTD0 I/O Standard

VSS VSS LVTTL

VSS VTTL HSTL

VTTL VSS 2.5V LVCMOS

VTTL VTTL 1.8V LVCMOS

Table 2. Data Pin Assignment

BE Pin Name Data Pin Name

BE[7] DQ[71:63]

BE[6] DQ[62:54]

BE[5] DQ[53:45]

BE[4] DQ[44:36]

BE[3] DQ[35:27]

BE[2] DQ[26:18]

BE[1] DQ[17:9]

BE[0] DQ[8:0]

Figure 6. SDR Echo Clock Delay

Input Clock

Echo Clock

Data Out

Echo Clock

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 11 of 52

address matches enable to generate the BUSY flag. However,

none of the addresses are saved into the busy address register .

When a busy readback is performed, the address of the first

match that happens at least two clocks cycles after the busy

readback is saved into the busy address register.

Variable Impedance Matching

Each port contains a Variable Impedance Matching circuit to set

the impedance of the IO driver to match the impedance of the

on-board traces. The impedance is set for all outputs except

JTAG and is done by port. To take advantage of the VIM feature,

connect a calibrating resistor (RQ) that is five times the value of

the intended line impedance from the ZQ[1:0][18] pin to VSS. The

output impedance is then adjusted to account for drifts in supply

voltage and temperature every 1024 clock cycles. If a port’s clock

is suspended, the VIM circuit retains its last setting until the clock

is restarted. On restart, it then resumes periodic adjustmen t. In

the case of a significant change in device temperature or supply

voltage, recalibration happens every 1024 clock cycles. A Master

Reset initializes the VIM circuitry. Table 5 shows the VIM param-

eters and Table 6 describes the VIM operation modes.

To disable VIM, connect the ZQ pin to VDDIO of the relative

supply for the IOs before a Master Reset.

Table 3. tCCS Timing for All Operating Modes

Port A—Early Arriving Port Port B—Late Arriving Port tCCS

C Rise to Opposite C Rise Setup Time for Non Corrupt Data Unit

Mode Active Edge Mode Active Edge

SDRCSDRCt

CYC(min) – 0.5 ns

Table 4. Deterministic Access Control Logic

Left Port Right Port Left Clock Right Clock BUSYLBUSYRDescription

Read Read X X H H No Collision

Write Read >tCCS 0 H H Read OLD Data

0>t

CCS H H Read NEW Data

<tCCS 0 H H Read OLD Data

H L Data Not Guaranteed

0<t

CCS H H Read NEW Data

H L Data Not Guaranteed

Read Write >tCCS 0 H H Read NEW Data

0>t

CCS H H Read OLD Data

<tCCS 0 H H Read NEW Data

L H Data Not Guaranteed

0<t

CCS H H Read OLD Data

L H Data Not Guaranteed

Write Write 0 >–tCCS & <tCCS L L Array Data Corrupted

0>t

CCS L H Array Stores Right Port Data

>tCCS 0 H L Array Stores Left Port Data

Table 5. V ariable Impedance Matching Parameters

Parameter Min Max Unit Tolerance

RQ Value 100 275 Ω± 2%

Output Impedance 20 55 Ω± 15%

Reset T i me N/A 1024 Cycles N/A

Update Time N/A 1024 Cycles N/A

Table 6. Variable Impedance Matching Operation

RQ Connection Output Configuration

100Ω - 275Ω to VSS Output Driver Impedance = RQ/5 ± 15%

at Vout = VDDIO/2

ZQ to VDDIO VIM Disabled. Rout < 20Ω at Vout =

VDDIO/2

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 12 of 52

Address Counter and Mask Register Operations [1]

Each port of the FullFlex family con tains a programmable burst

address counter. The burst counter contains four registers: a

counter register, a mask register, a mirror register, and a busy

address register.

The counter re gister contains the address used to access the

RAM array. It is changed only by the Master Reset (MRST),

Counter Reset, Counter Load, Retransmit, and Counter

Increment operations.

The mask register value affects the Counter Increment and

Counter Reset operations by preventin g the corresponding bi ts

of the counter register from changing. It also affects the counter

interrupt output (CNTINT). The mask register is only changed by

Mask Reset, Mask Load, and MRST. The Mask Load operation

loads the value of the address bus into the mask register. The

mask register defines the counting range of the counter register .

The mask register is divided into two or three consecutive

regions. Zero or more 0s define the masked region and one or

more 1s define the unmasked portion of the counter register . The

counter register may be divided up to three regions. The regio n

containing the least significant bits must be no more than two 0s.

Bits one and zero may be 10 respectively, masking the least

significant counter bit and causing the counter to increment by

two instead of one. If bits one and zero are 00, the two least

significant bits are masked and the counter increments by four

instead of one. For example, in the case of a 256Kx72 configu-

ration, a mask register value of 003FC divides the mask register

into three regions. With bit 0 being the least significant bit and bit

17 being the most significant bit, the two least signi ficant bit s are

masked, the next eight bits are unmasked, and the remaining bits

are masked.

The mirror register reloads a counter register on retransmit

operations (see Retransmit on page 14) and wrap functions (see

Counter Inte rrupt on page 14 below). The last value loaded into

the counter register is stored in the mirror register. The mirror

and counter load.

Table 7 on page 13 summarizes the operations of these registers

and the required input control signa ls. All signals except MRST

are synchronized to the ports clock.

Counter Load Operation [1]

The address counter and mirror registers are loaded with the

address value presented on the address lines. This value ranges

from 0 to 1FFFFF.

Mask Load Operation [1]

The mask register is loaded with the address value presented on

the address bus. This value ranges from 0 to 1FFFFF though not

all values permit correct increment operations. Permitted values

are in the form of 2n–1, 2n–2, or 2n–4. The counter register is only

segmented up to three regions. From the most significant bit to

the least significant bit, permi tted values have zero or more 0 s,

one or more 1s, and the least significant two bits are 11, 10, or

00. Thus 1FFFFE, 07FFFF, and 003FFC are permitted values

but 02FFFF, 003F FA, and 07FFE4 are not.

Counter Readback Operation

The internal value of the counter register is read out on the

address lines. The address is valid tCA after the selected number

of latency cycles configured by FTSEL. The data bus (DQ) is

tri-stated on the cycle that the address is presented on the

address lines. Figure 7 on page 15 shows a block diagram of this

logic.

Mask Readback Operation

The internal value of the mask register is read out on the address

lines. The address is valid tCA after the selected number of

latency cycles configured by FTSEL. The data bus (DQ) is

tri-stated on the cycle that the address is presented on the

address lines. Figure 7 on page 15 shows a block diagram of the

operation.

Counter Reset Operation

All unmasked bits of the counter and mirror registers are reset to

‘0’. All masked bits remain unchanged. A mask reset followed by

a counter reset resets the counter and mirror registers to 00000.

Mask Reset Operation

The mask register is reset to all 1s, that unmasks every bit of the

burst counter.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 13 of 52

Table 7. Burst Counter and Mask Register Control Operations

The burst counter and mask register control operation for any port follows. [20, 21]

CMRST CNTRST CNT/MSK CNTEN ADS RET Operation Description

X L X X X X X Master Reset Reset address counter to all 0s, mask register to all

1s, and busy address to all 0s.

H L H X X X Counter Reset Reset counter and mirror unmasked portion to all 0s.

H L L X X X Mask Reset Reset mask register to all 1s.

H H H L L X Counter Load Load burst counter and mirror with external address

value presented on address lines.

H H L L L X Mask Load Load mask register with value presented on the

address lines.

H H H L H L Retransmit Load counter with value in the mirror register.

H H H L H H Counter

Increment Internally increment address counter value.

H H H H H H Counter Hold Constantly hold the address value for multiple clock

cycles.

H H H H L H Counter

Readback Read out counter internal value on address lines.

H H L H L H Mask Readback Read out mask register value on address lines.

H H L H H L Busy Address

Readback Read out first busy address after last busy address

readback.

HH LLHXReserved

HH LHLLReserved

HH LHHHReserved

HH HHLLReserved

HH HHHLReserved

Notes

20.“X” = Don’t Care, “H” = HIGH, “L” = LOW.

21.Counter operation and mask register operation is independent of chip enables.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 14 of 52

Increment Operation [1]

After the address counter is initially loaded with an external

address, the counter can internally increment the address value

and address the entire memory array . Only the unmasked bits of

the counter register are incremented. For a counter bit to

change, the corresponding bit in the ma sk reg ister must be 1. If

the two least significant bits of the mask register are 1 1, the burst

counter increments by one. If the two least significant bits are 10,

the burst counter increments by two, and if they are 00, the burst

counter increments by four. If all unmasked counter bits are

incremented to 1 and WRP is deasserte d, the next increment l

wraps the counter back to the initially loaded value. The cycle

before the increment that results in all unmasked counter bits to

become 1s, a counter interrupt flag (CNTINT) is asserted if the

counter is incremented again. This increment causes the counter

to reach its maximum value and the ne xt increment returns the

counter register to its initial value that was stored in the mirror

portion of the counter is filled with 0 instead. The example shown

in Figure 8 on page 16 shows an example of the

CYDD36S18V18 device with the mask register loaded with a

mask value of 00007F unmasking the seven least significant bits.

Setting the mask register to this value enables the counter to

access the entire memory space. The address counter is then

loaded with an initial value of 000005 assuming WRP is

deasserted. The ma sked bits, the seventh address through the

twenty-first address, do not increment in an increment operation.

The counter address starts at address 000005 and increments

its internal address value until it reaches the mask register value

of 00007F. The counter wraps around the memory block to

location 000005 at the next count. CNTINT is issued when th e

counter reaches the maximum –1 count.

Hold Operation

The value of all three registers is constantly maintained

unchanged for an unlimited number of clock cycles. This

operation is useful in applications where wait states are needed

or when address is available a few cycles ahead of data in a

shared bus interface.

Retransmit

Retransmit enables repeated access to the same block of

memory without the need to reload the initial address. An internal

mirror register stores the address counter value last loaded.

While RET is asserted low, the counter continues to wrap back

to the value in the mirror register independent of the state of

WRP.

Counter Interrupt

The counter interrupt (CNTINT) is asserted LOW one clock cycle

before an increment operation that results in the unmasked

portion of the counter register being all 1s. It is deasserted by

counter reset, counter load, mask reset, mask load, and MRST.

Counting by Two

When the two least significant bits of the mask register are 10,

the counter increments by two.

Counting by Four

When the two least significant bits of the mask register are 00,

the counter increments by four.

Mailbox Interrupts

Use the upper two memory locations for me ssage passing and

permit communications between ports. Table 8 on page 16

shows the interrupt operation for both ports. The highest memory

location is the mailbox for the right port and the maximum

address – 1 is the mailbox for the left port.

When one port writes to the other port’s mailbox, the INT flag of

the port that the mailbox be longs to is asserted LOW. The INT

flag remains asserted until the mailbox location is read by the

other port. When a port reads its mailbox, the INT flag is

deasserted high after one cycle of latency with respect to the

input clock of the port to which the mailbox belongs and is

independent of OE.

As shown in Tab le 8 on page 16, to set the INTR flag, a write

operation by the left port to address 1FFFFF asserts INTR LOW.

A valid read of the 1FFFFF location by the right port resets INTR

HIGH after one cycle of latency with respect to the right port’s

clock. You must ac tivate at least one byte enable to set or reset

the mailbox interrupt.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 15 of 52

Figure 7. Counter, Mask, and Mirror Logic Block Diagram

Figure 7 shows the counter, mask, and mirror logic block diagram. [1]

From

Mask

Mirror Counter

Address

Decode

RAM

Array

Wrap

Increment

Logic

Wrap

Detect

From

Mask

From

Counter

Bit 0

and 1 Wrap

20 20

Load/Increment

CNT/MSK

CNTEN

CNTRST

Decode

Logic

AMask

Counter/

Address

From

Address

Lines To Readback

and Address

Decode

MRST

RET

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 16 of 52

Figure 8. Programmable Counter-Mask Register Operation with WRP deasserted

Figure 8 shows the programmable counter-mask operation with WRP deasserted. [1, 25]

Table 8. Interrupt Operation Example

Table 8 shows the interrupt operation example. [1, 20, 22, 23, 24]

Function Left Port Right Port

R/WLCELA0L–20L INTLR/WRCERA0R–20R INTR

Set Right INTR Flag L L Max Address X X X X L

Reset Right INTR Flag X X X X H L Max Address H

Set Left INTL Flag X X X L L L Max Address–1 X

Reset Left INTL Flag H L Max Address–1 H X X X X

220 219 2621

2522

242320

220 219 2621

2522

242320

220 219 2621

2522

242320

220 219 2621

2522

242320

0s 1

0111

Xs 0

X001

Xs 1

X111

Xs 0

X001

Masked Address Unmasked Address

Mask

LSB

Address

Counter

LSB

CNTINT

Example:

Load

Counter-Mask

Load

Address

Counter = 00000 5

Max

Address

Value

Max + 1

Address

Value

Notes

22.CE is internal signal. CE = LOW if CE0 = LOW and CE1 = HIGH. For a single read operation, CE only needs to be asserte d once at the rising edge of the C and is

deasserted after that. Data is out after the following C edge and is tri-stated after the next C edge.

23.OE is “Don’t Care” for mailbox operation.

24.At least one of BE0, BE 1 , BE2, BE3, BE4, BE5, BE 6 , or BE7 must be LOW.

25.The “X” in this diagram represents the counter’s upper bits.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 17 of 52

Master Reset

The FullFlex family of Dual Ports undergoes a complete reset

when MRST is asserted. MRST must be driven by VDDIOL refer-

enced levels. The MRST is asserted asynchronously to the

clocks and must remain asserted for at least tRS. When asserted

MRST deasserts READY, initializes the internal bu rst counters,

internal mirror registers, and internal bu sy addresses to zero. It

also initializes the internal mask register to all 1s. All mailbox

interrupts (INT), busy address outputs (BUSY), and burst

counter interrupts (CNTINT) are de asserted upon master reset.

Additionally, do not release MRST until all power supplies

including VREF are fully ramped and all port clocks and mode

select inputs (LOWSPD, ZQ, CQEN, FTSEL, and PORTSTD)

are valid and stable. This begins calibration of the DLL and VIM

circuits. READY is asserted within 1024 clock cycles. READY is

a wired OR capable output with a strong pull up and weak pul l

down. Up to four outputs may be connected together. For faster

pull down of the signal, connect a 250 Ohm resistor to VSS. If

the DLL and VIM circuits are disabled for a port, the port is opera-

tional within five clock cycles. However, the READY is asserted

within 160 clock cycles.

IEEE 1149.1 Serial Boundary Scan (JTAG)

The FullFlex families incorporate an IEEE 1149.1 serial

boundary scan test access port (TAP). The TAP operates using

JEDEC-standard 3.3V or 2.5V IO logic levels d epending on th e

VTTL power supply . It is composed of four input connections and

one output connection re quired by the test logic defin ed by the

standard.

Table 9. JTAG IDCODE Register Definitions

Part Number Configuration Value

CYD36S72V18 512Kx72 0C026069h (x2)

CYD36S36V18 1024Kx36 0C023069h

CYD36S18V18 2048Kx36 0C024069h

CYD18S72V18 256Kx72 0C025069h

CYD18S36V18 512Kx36 0C026069h

CYD18S18V18 1024Kx18 0C027069h

CYD09S72V18 128Kx72 0C028069h

CYD09S36V18 256Kx36 0C029069h

CYD09S18V18 512Kx18 0C02A069h

CYD04S72V18 64Kx72 0C02B069h

CYD04S36V18 128Kx36 0C02C069h

CYD04S18V18 256Kx18 0C02D069h

CYD02S36V18 64Kx36 0C030069h

Table 10.Scan Registers Sizes

Instruction 4

Bypass 1

Identification 32

Boundary Scan n[26]

Table 11.Instruction Identification Codes

Instruction Code Description

EXTEST 0000 Captures the input and output ring contents. Places the BSR between the TDI and TDO.

BYPASS 1111 Places the BYR between TDI and TDO.

IDCODE 1011 Loads the IDR with the vendor ID code and places the register between TDI and TDO.

HIGHZ 0111 Places BYR between TDI and TDO. Forces all FullFlex72 and FullFlex36 output drivers to a

High-Z state.

CLAMP 0100 Controls boundary to 1 or 0. Places BYR between TDI and TDO.

SAMPLE/PRELOAD 1000 Captures the input and output ring contents. Places BSR between TDI and TDO.

RESERVED All other

codes Other combinations are reserved. Do not use other than the mentioned combinations.

Note

26.Details of the boundary scan length is found in the BSDL file for the device.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 18 of 52

Maximum Ratings

Exceeding maximum ratings may impair the useful life of the

device. User guidelines are not te sted.

Storage Temperature................................ –65°C to + 150°C

Ambient Temperature with

Power Applied ........................................... –55°C to + 125°C

Supply Voltage to Ground Potential...............–0.5V to + 4.1V

DC Voltage Applied to

Outputs in High-Z State......................–0.5V to VDDIO + 0.5V

DC Input Voltage ................................–0.5V to VDDIO + 0.5V

Output Current into Output s (LO W)............................ 20 mA

Static Discharge Voltage...........................................> 2200V

(JEDEC JESD8-6, JESD8-B)

Latch-up Current................................... ... .. .............> 200 mA

Operating Range

Range Ambient

Temperature VCORE

Commercial 0°C to +70°C 1.8V ± 100 mV

1.5V ± 80 mV

Industrial –40°C to +85°C 1.8V ± 100 mV

1.5V ± 80 mV

Power Supply Requirements

Min Typ Max

LVTTL VDDIO 3.0V 3.3V 3.6V

2.5V LVCMOS VDDIO 2.3V 2.5V 2.7V

HSTL VDDIO 1.4V 1.5V 1.9V

1.8V LVCMOS VDDIO 1.7V 1.8V 1.9V

3.3V VTTL 3.0V 3.3V 3.6V

2.5V VTTL 2.3V 2.5V 2.7V

HSTL VREF 0.68V 0.75V 0.95V

Electrical Characteristics

Over the Operating Range

Parameter Description Configuration All Speed Bins Unit

Min Typ Max

VOH Output HIGH Voltage

(VDDIO = Min, IOH = –8 mA) LVTTL 2.4[27] V

(VDDIO = Min, IOH = –4 mA) HSTL (DC)[28] VDDIO – 0.4 [27] V

(VDDIO = Min, IOH = –4 mA) HSTL (AC)[28] VDDIO – 0.5[27] V

(VDDIO = Min, IOH = –6 mA) 2.5V LVCMOS 1.7[27] V

(VDDIO = Min, IOH = –4 mA) 1.8V LVCMOS VDDIO – 0.45 [27] V

VOL Output HIGH Voltage

(VDDIO = Min, IOL = 8 mA) LVTTL 0.4[27] V

(VDDIO = Min, IOL = 4 mA) HSTL(DC)[28] 0.4[27] V

(VDDIO = Min, IOL = 4 mA) HSTL (AC)[28] 0.5[27] V

(VDDIO = Min, IOL = 6 mA) 2.5V LVCMOS 0.7[27] V

(VDDIO = Min, IOL = 4 mA) 1.8V LVCMOS 0.45[27] V

VIH Input HIGH Voltage LVTTL 2 VDDIO + 0.3 V

HSTL(DC)[28] VREF + 0.1 VDDIO + 0.3 V

2.5V LVCMOS 1.7 V

1.8V LVCMOS 0.65 x VDDIO V

VIL Input LOW Voltage LVTTL –0.3 0.8 V

HSTL(DC)[28] –0.3 VREF – 0.1 V

2.5V LVCMOS 0.7 V

1.8V LVCMOS 0.35 x VDDIO V

Notes

27.These parameters are met with VIM disabled.

28.The DC specifications are measured under steady state conditions. The AC specifications are measured while switchin g at speed. AC VIH/VIL in HSTL mode are

measured with 1V/ns input edge rates

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 19 of 52

READY

VOH

Output HIGH Voltage

(VDDIO = Min, IOH = –24 mA) LVTTL 2.7[27] V

(VDDIO = Min, IOH = –12 mA) HSTL(DC)[28] VDDIO – 0.4[27] V

(VDDIO = Min, IOH = –12 mA) HSTL (AC) [28] VDDIO – 0.5 [27] V

(VDDIO = Min, IOH = –15 mA) 2.5V LVCMOS 2.0[27] V

(VDDIO = Min, IOH = –12 mA) 1.8V LVCMOS VDDIO – 0.45[27] V

READY VOL Output HIGH Voltage

(VDDIO = Min, IO = 0.12 mA) LVTTL 0.4[27] V

(VDDIO = Min, IOL = 0.12 mA) HSTL(DC)[28] 0.4[27] V

(VDDIO = Min, IOL = 0.12 mA) HSTL (AC)[28] 0.5[27] V

(VDDIO = Min, IOL = 0.15 mA) 2.5V LVCMOS 0.7[27] V

(VDDIO = Min, IOL = 0.08 mA) 1.8V LVCMOS 0.45 [27] V

IOZ Output Leakage Current –10 10 μA

IIX1 Input Leakage Current Except

TDI, TMS, MRST, PORTSTD –10 10 μA

IIX2 Input Leakage Current TDI,

TMS, MRST –300 10 μA

IIX3 Input Leakage Current

PORTSTD –10 300 μA

Electrical Characteristics

Over the Operating Range (continued )

Parameter Description Configuration All Speed Bins Unit

Min Typ Max

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 20 of 52

Electrical Characteristics

Over the Operating Range

Parameter Description Configuration –200 –167 –133 Unit

Typ Max Typ Max Typ Max

ICC Operating Current

(VCORE = Max,IOUT = 0 mA)

Outputs Disabled

512Kx72 Com. 1440 1800 1280 1620 1120 1430 mA

Ind. N/A N/A 1330 1730 1170 1550 mA

1024Kx36 Com. 1180 1500 1050 1350 930 1220 mA

Ind. N/A N/A 1110 1470 980 1330 mA

2048Kx18 Com. 1130 1430 1000 1290 890 1160 mA

Ind. N/A N/A 1060 1410 940 1280 mA

256Kx72 Com. 800 980 700 880 N/A N/A mA

Ind. 820 1030 730 930 N/A N/A mA

512Kx36 Com. 640 800 570 720 N/A N/A mA

Ind. 670 860 590 780 N/A N/A mA

1024Kx18 Com. 610 770 540 690 N/A N/A mA

Ind. 640 830 570 750 N/A N/A mA

128Kx72 Com. 640 790 560 700 N/A N/A mA

Ind. 660 830 580 740 N/A N/A mA

256Kx36 Com. 540 640 470 570 N/A N/A mA

Ind. 550 670 490 600 N/A N/A mA

512Kx18 Com. 550 660 480 580 N/A N/A mA

Ind. 570 690 500 610 N/A N/A mA

64Kx72 Com. 620 740 540 650 N/A N/A mA

Ind. 630 770 550 680 N/A N/A mA

128Kx36 Com. 510 590 450 520 N/A N/A mA

Ind. 520 600 460 530 N/A N/A mA

256Kx18 Com. 530 610 460 530 N/A N/A mA

Ind. 540 620 470 550 N/A N/A mA

64Kx36 Com. N/A N/A mA

Ind. N/A N/A mA

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 21 of 52

ISB1 Standby Current

(Both Ports TTL Level)

CEL and CER ≥ VIH, f = fMAX

512Kx72 Com. 1000 1250 920 1160 830 1060 mA

Ind. N/A N/A 970 1260 880 1170 mA

1024Kx36 Com. 910 1140 820 1050 740 960 mA

Ind. N/A N/A 880 1160 790 1080 mA

2048Kx18 Com. 890 1110 810 1030 730 940 mA

Ind. N/A N/A 860 1140 780 1050 mA

256Kx72 Com. 500 630 460 580 N/A N/A mA

Ind. 530 680 490 630 N/A N/A mA

512Kx36 Com. 460 570 410 530 N/A N/A mA

Ind. 480 630 440 580 N/A N/A mA

1024Kx18 Com. 450 560 410 520 N/A N/A mA

Ind. 470 610 430 570 N/A N/A mA

128Kx72 Com. 400 490 360 450 N/A N/A mA

Ind. 420 540 380 490 N/A N/A mA

256Kx36 Com. 380 440 340 400 N/A N/A mA

Ind. 390 470 360 430 N/A N/A mA

512Kx18 Com. 390 460 350 410 N/A N/A mA

Ind. 410 480 370 440 N/A N/A mA

64Kx72 Com. 380 450 340 400 N/A N/A mA

Ind. 390 480 350 430 N/A N/A mA

128Kx36 Com. 360 400 320 360 N/A N/A mA

Ind. 360 410 330 370 N/A N/A mA

256Kx18 Com. 370 410 320 370 N/A N/A mA

Ind. 370 420 330 380 N/A N/A mA

64Kx36 Com. N/A N/A mA

Ind. N/A N/A mA

Electrical Characteristics

Over the Operating Range (continued )

Parameter Description Configuration –200 –167 –133 Unit

Typ Max Typ Max Typ Max

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 22 of 52

ISB2 Standby Current

(One Port TTL or CMOS Level)

CEL | CER ≥ VIH, f = fMAX

512Kx72 Com. 1300 1570 1160 1410 1020 1260 mA

Ind. N/A N/A 1210 1520 1070 1370 mA

1024Kx36 Com. 1090 1330 980 1210 870 1100 mA

Ind. N/A N/A 1030 1330 920 1210 mA

2048Kx18 Com. 1040 1270 930 1160 830 1050 mA

Ind. N/A N/A 980 1270 880 1160 mA

256Kx72 Com. 650 790 580 710 N/A N/A mA

Ind. 680 840 610 760 N/A N/A mA

512Kx36 Com. 550 670 490 610 N/A N/A mA

Ind. 570 730 520 670 N/A N/A mA

1024Kx18 Com. 520 640 470 580 N/A N/A mA

Ind. 550 690 490 640 N/A N/A mA

128Kx72 Com. 520 630 460 560 N/A N/A mA

Ind. 550 670 480 610 N/A N/A mA

256Kx36 Com. 460 530 400 470 N/A N/A mA

Ind. 480 560 430 500 N/A N/A mA

512Kx18 Com. 460 530 410 480 N/A N/A mA

Ind. 480 560 430 510 N/A N/A mA

64Kx72 Com. 500 580 440 510 N/A N/A mA

Ind. 510 610 450 550 N/A N/A mA

128Kx36 Com. 440 480 380 420 N/A N/A mA

Ind. 450 500 390 440 N/A N/A mA

256Kx18 Com. 440 490 390 430 N/A N/A mA

Ind. 450 500 400 450 N/A N/A mA

64Kx36 Com. N/A N/A mA

Ind. N/A N/A mA

Electrical Characteristics

Over the Operating Range (continued )

Parameter Description Configuration –200 –167 –133 Unit

Typ Max Typ Max Typ Max

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 23 of 52

Electrical Characteristics

Over the Operating Range (continued )

Parameter Description Configuration All Speed Bins Unit

Typ Max

ISB3 Standby Current

(Both Ports CMOS Level)

CEL and CER ≥ VCORE – 0.2V, f = 0

512Kx72 Com. 410 590 mA

Ind. 460 700 mA

1024Kx36 Com. 410 590 mA

Ind. 460 700 mA

2048Kx18 Com. 410 590 mA

Ind. 460 700 mA

256Kx72 Com. 210 300 mA

Ind. 230 350 mA

512Kx36 Com. 210 300 mA

Ind. 230 350 mA

1024Kx18 Com. 210 300 mA

Ind. 230 350 mA

128Kx72 Com. 150 200 mA

Ind. 170 220 mA

256Kx36 Com. 150 200 mA

Ind. 170 220 mA

512Kx18 Com. 150 200 mA

Ind. 170 220 mA

64Kx72 Com. 130 150 mA

Ind. 140 170 mA

128Kx36 Com. 130 150 mA

Ind. 140 170 mA

256Kx18 Com. 130 150 mA

Ind. 140 170 mA

Table 12.Capacitance

Signals Packages

CYD18S72V18

CYD09S72V18

CYD04S72V18

CYD18S36V18

CYD09S36V18

CYD04S36V18

CYD02S36V18

CYD18S18V18

CYD09S18V18

CYD04S18V18

CYD36S72V18

CYD36S36V18 CYD36S18V18

OE 12 pF 12 pF 20 pF 20 pF

BE, DQ 10 pF 18 pF 16 pF 30 pF

All other signals 10 pF 10 pF 16 pF 16 pF

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 24 of 52

AC Test Load and Waveforms

Figure 9. Output Test Load for LVTTL/CMOS

Figure 10. Output Test Load for HSTL

Figure 11. HSTL Input Waveform

Output

50 Ohm 50 O hm

VTH = 1.5V for LVTTL

VTH = 50% VDDIO for 2.5V C MO S

VTH = 50% VDDIO for 1.8V C MO S

RQ =250 Ohm

Device under

test

VREF VREF = NC

Test Point

C = 10pF

READY

R=250 O hm VTH

Output

50 Ohm 50 Ohm

VTH = 50% VDDIO

RQ=250 Ohm

Device under

te st

VREF

VREF = 0.75V

Test Point

C= 10pF for SDR

R=250 Ohm

READY VTH

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 25 of 52

Switching Characteristics Over the Operating Range

Table 13.SDR Mode, Signals Affected by DLL

Parameter

Description DLL ON (LOWSPD=1)[31] DLL OFF

(LOWSPD=0)

[31]

–200 –167 –133 Unit

Min Max Min Max Min Max Min Max

tCD2[34] C Rise to DQ V alid for Pipelined

Mode 3.30

[30, 33] 4.00

[30, 33] 4.50

[30, 33] 6.00

[30, 33] ns

tCCQ[34] C Rise to CQ Rise 1.00 3.30[33] 1.00 4.00[33] 1.00 4.50[33] 1.00 6.00[33] ns

tCKHZ2[29, 34] C Rise to DQ Output High Z in

Pipelined Mode 1.00 3.30

[30, 33] 1.00 4.00

[30, 33] 1.00 4.50

[30, 33] 1.00 6.00

[30, 33] ns

tCKLZ2[29, 34] C Rise to DQ Output Low Z in

Pipelined Mode 1.00 1.00 1.00 1.00 ns

Table 14.SDR Mode

Parameter Description –200 –167 –133 Unit

Min Max Min Max Min Max

fMAX

(PIPELINED)Maximum Operating Frequency for Pipelined Mode 100 200 100 167 100 133 MHz

fMAX (FLOW

THROUGH)Maximum Operating Frequency for Flow Through

Mode 77 66.7 55.6 MHz

tCYC

(PIPELINED)C Clock Cycle Time for Pipelined Mode 5.00

[33] 10.00 6.00

[33] 10.00 7.00

[33] 10.00 ns

tCYC (FLOW X

THROUGH)C Clock Cycle Time for Flow Through Mode 13.00

[33] 15.00

[33] 18.00

[33] ns

tCKD C Clock Duty Time 45 55 45 55 45 55 %

tSD Data Input Setup Time

to C Rise HSTL

1.8V LVCMOS 1.50

[30, 33] 1.70

[30, 33] 1.80

[30, 33] ns

2.5V LVCMOS 3.3V

LVTTL 1.75

[30, 33] 1.95

[30, 33] 2.05

[30, 33] ns

tHD[32] Data Input Hold T ime af ter C Rise 0.5 0.5 0.5 ns

tSAC Address and Control

Input Setup Time to C

Rise

HSTL

1.8V LVCMOS 1.50

[30, 32,

33]

1.70

[30, 32,

33]

1.80

[30, 32,

33]

2.5V LVCMOS 3.3V

LVTTL 1.75

[30, 32,

33]

1.95

[30, 32,

33]

2.05

[30, 32,

33]

tHAC[32] Address and Control Input Hold Time after C Rise 0.50 0.60 0.70 ns

tOE Output Enable to Data Valid 4.40

[30,33] 5.00

[30,33] 5.50

[30,33] ns

tOLZ[29] OE to Low Z 1.00 1.00 1.00 ns

Notes

29.Parameters specified with the load capacita nce in Figure 9 and Figure 10.

30.For the x18 devices, add 200 p s to this parameter in Table 14.

31.Test conditions assume a signal transition time of 2 V/ns.

32.Add 300 ps to this timing fo r 36M devices.

33.Add 15% to this parameter if a VCORE of 1.5V is used.

34.This parameter assumes input clock cycle to cycle jitter of ± 0ps.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 26 of 52

tOHZ[29] OE to High Z 1.00 4.40

[30, 33] 1.00 5.00

[30, 33] 1.00 5.50

[30, 33] ns

tCD1 C Rise to DQ Valid for Flow Through Mode

(LowSPD = 1) 9.00

[30, 33] 11.00

[30, 33] 13.00

[30, 33] ns

tCA1 C Rise to Address Readback Valid for Flow Through

Mode 9.00[33] 11.00[33] 13.00

[33] ns

tCA2 C Rise to Address Readback Valid for Pipelined

Mode 5.00[33] 6.00[33] 7.50[33] ns

tDC[34] DQ Output Hold after C Rise 1.00 1.00 1.00 ns

tJIT Clock Input Cycle to Cycle Jitter +/- 200 +/- 200 +/- 200 ps

tCQHQV[34] Echo Clock (CQ) High

to Output Valid HSTL

1.8V LVCMOS 0.70[30] 0.80[30] 0.90[30] ns

2.5V LVCMOS 3.3V

LVTTL 0.80[30] 0.90[30] 1.00[30] ns

tCQHQX[34] Echo Clock (CQ) High

to Output Hold HSTL

1.8V LVCMOS –0.70 –0.80 –0.90 ns

2.5V LVCMOS 3.3V

LVTTL –0.85 –0.95 –1.05 ns

tCKHZ1[29] C Rise to DQ Output High Z in Flow Through Mode 1.00 9.00

[30, 33] 1.00 11.00

[30, 33] 1.00 13.00

[30, 33] ns

tCKLZ1[29] C Rise to DQ Output Low Z in Flow Through Mode 1.00 1.00 1.00 ns

tAC Address Output Hold after C Rise 1.00 1.00 1.00 ns

tCKHZA1[29] C Rise to Address Output High Z for Flow Through

Mode 1.00 9.00[33] 1.00 11.00

[33] 1.00 13.00

[33] ns

tCKHZA2[29] C Rise to Address Output High Z for Pipelined Mode 1.00 5.00[33] 1.00 6.00[33] 1.00 7.50[33] ns

tCKLZA[29] C Rise to Address Output Low Z 1.00 1.00 1.00 ns

tSCINT C Rise to CNTINT Low 1.00 3.30[33] 1.00 4.00[33] 1.00 4.50[33] ns

tRCINT C Rise to CNTINT High 1.00 3.30[33] 1.00 4.00[33] 1.00 4.50[33] ns

tSINT C Rise to INT Low 0.50 7.00[33] 0.50 8.00[33] 0.50 8.50[33] ns

tRINT C Rise to INT High 0.50 7.00[33] 0.50 8.00[33] 0.50 8.50[33] ns

tBSY C Rise to BUSY Valid 1.00 3.30[33] 1.00 4.00[33] 1.00 4.50[33] ns

Table 14.SDR Mode (continued)

Parameter Description –200 –167 –133 Unit

Min Max Min Max Min Max

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 27 of 52

Table 15.Master Reset Timing

Parameter Description –200 –167 –133 Unit

Min Max Min Max Min Max

tPUP Power Up Time 1 1 1 ms

tRS Master Reset Pulse Width 5 5 5 cycles

tRSR Master Reset Recovery Time 5 5 5 cycles

tRSF Master Reset to Output s Inactive/Hi Z 15 18 22.50 ns

tRDY[35] Master Reset Release to Port Ready 1024 1024 1024 cycles

tCORDY[36] C Rise to Port Ready 9.5[33] 11[33] 13[33] ns

Table 16.JTAG Timing

Parameter Description –200 –167 –133 Unit

Min Max Min Max Min Max

fJTAG JTAG TAP Controller Frequency 20 20 20 MHz

tTCYC TCK Cycle Time 50 50 50 ns

tTH TCK High Time 20 20 20 ns

tTL TCK Low Time 20 20 20 ns

tTMSS TMS Setup to TCK Rise 10 10 10 ns

tTMSH TMS Hold to TCK Rise 10 10 10 ns

tTDIS TDI Setup to TCK Rise 10 10 10 ns

tTDIH TDI Hold to TCK Rise 10 10 10 ns

tTDOV TCK Low to TDO Valid 10 10 10 ns

tTDOX TCK Low to TDO Invalid 0 0 0 ns

tJXZ TCK Low to TDO High Z 15 15 15 ns

tJZX TCK Low to TDO Active 15 15 15 ns

Notes

35.READY is a wired OR capable output with a weak pull down. For a decreased falling delay, connect a 250-Ω resistor to VSS.

36.Add this propagat ion delay after tRDY for all Master Reset Operations

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 28 of 52

Switching Waveforms

Figure 12. JTAG Timing

Figure 13. Master Reset [35]

Test Clock

Test Mode Select

TCK

TMS

Test Data-In

TDI

Test Data-Out

TDO

tTCYC

tTMSH

tTL

tTH

tTMSS

tTDIS tTDIH

tTDOX tTDOV

tPUP tRS

tRSF

tRSR

VCORE

MRST

READY

All Address

& Data

All Other

Inputs

tRDY tCORDY

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 29 of 52

Figure 14. READ Cycle for Pipelined Mode

Figure 15. WRITE Cycle for Pipelined and Flow Through Modes

Switching Waveforms (continued)

CYC

2 Pipelined stages

n+1

n+2

n+3

n+4

n+5

n+6

x-1

n+1

n+2

n+3

n+4

CD2

SAC

HAC

tCYC

R/W

AAnAn+1 An+2 An+3 An+4 An+5 An+6

DQnDQn+1 DQn+2 DQn+3 DQn+4 DQn+5 DQn+6

2 Pipelined stages

tSD tHD

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 30 of 52

Figure 16. READ with Address Counter Advance for Pipelined Mode

Figure 17. READ with Address Counter Advance for Flow Through Mode

Switching Waveforms (continued)

tCYC

DQx-1 DQxDQnDQn+1 DQn+2

Internal

ADS

Address

CNTEN

An+1 An+2 An+3

DQn+3

tCYC

tSAC tHAC

tHAC

tDC

tCD1

tSAC

READ EXTERNAL ADDRESS READ WITH COU NTERCOUNTER HOLDREAD WITH COUN TER

DQx DQn + 1 DQn + 2 DQn + 3 DQn + 4DQn

CNTEN

ADS

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 31 of 52

Figure 18. Port-to-Port WRITE–READ for Pipelined Mode

Figure 19. Chip Enable READ for Pipelined Mode

Switching Waveforms (continued)

Left Port

R/W

Right Port

R/W

CD2

SAC

HAC

CYC

CCS

R/W

n+1

n+2

n+3

n+4

n+5

n+6

SAC

HAC

CYC

CE0

CE1

DQ DQ

n+3

CD2

CKLZ2

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 32 of 52

Figure 20. OE Controlled WRITE for Pipelined Mode

Figure 21. OE Controlled WRITE for Flow Through Mode

Switching Waveforms (continued)

R/W

AAx+1 Ax+2 Ax+3 AnAn+1 An+2 An+3

tCYC

DQx-1 DQx

DQx+1 DQnDQn+1 DQn+2 DQn+3

tOHZ

R/W

AAx+1 Ax+2 Ax+3 AnAn+1 An+2 An+3

tCYC

DQxDQx+1

DQx+2 DQnDQn+1 DQn+2 DQn+3

tOHZ

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 33 of 52

Figure 22. Byte-Enable READ for Pipelined Mode

Switching Waveforms (continued)

R/W

AAnAn+1 An+2 An+3

tCYC

BE7

BE6

BE5

BE4

BE3

BE2

BE1

BE0

DQ63:71

DQ54:62

DQ45:53

DQ36:44

DQ27:35

DQ18:26

DQ9:17

DQ0:8

DQn+1(63:71)

DQn+1(54:62)

DQn+1(27:35)

DQn+2(45:53)

DQn+2(36:44)

DQn+2(18:26)

DQn+3(9:17)

DQn+3(0:8)

tCKLZ2 tCKHZ2

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 34 of 52

Figure 23. Port-to-Port WRITE-to-READ for Flow Through Mode

Switching Waveforms (continued)

tHD

tSD

tCD1

tDC

tSAC tHAC

tCD1

tCCS

tHAC

tSAC

MATCH

VALID

NO MATC H

NO MATCH

MATCH

VALID VALID

R/WL

DQL

R/WR

DQR

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 35 of 52

Figure 24. Busy Address Readback for Pipelined and Flow Th rough Modes, CNT/MSK = RET = LOW[37]

Figure 25. Read Cycle for Flow Through Mode

Switching Waveforms (continued)

Internal Amatch+2 Amatch+3 Amatch+4

tCYC

BUSY

CNTEN

ADS

External Amatch

tCA2 tAC

Address

Pipelined

~Amatch

tCA1 tAC

Flow through

Address

External

Address

tCYC

tSAC tHAC

tCKHZ1

tDC

tOE

tOLZ

tOHZ

tDCtCD1

tCKLZ1

tHACtSAC

CE1

CE0

An + 1 An + 3An + 2

DQn DQn + 1 DQ n + 2

R/W

BEn

Note

37.Amatch is the matching address that is reported on the address bus of the losing port. The counter operation selected for report i ng the address is “Busy Address

Readback.”

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 36 of 52

Figure 26. RE AD-to -W RI TE for P ipe li ne d Mode (OE = VIL)[38, 39, 40]

Figure 27. READ-to-WRITE for Pipelined Mode (OE Controlled)[41, 42]

Switching Waveforms (continued)

AAxAnAn+1 An+2

tCYC

DQx-2 DQx-1 DQxDQnDQn+1 DQn+2

tCH

tCL

tSAC tHAC tSAC tHAC

tDC

tCD2 tCKHZ2 tSD tHD

R/W

tCKLZ2

R/W

AAxAx+1 Ax+2 AnAn+1 An+2 An+3

tCYC

DQx-2 DQx-1 DQxDQnDQn+1 DQn+2 DQn+3

tSAC tHAC

tOHZ tSD tHD

Notes

38.When OE = VIL, the last read operation is enabled to complet e before the DQ bus is tri-stated and the user is enabled to drive write data.

39.Two dummy writes are issued to accomplish bus turnaround. The third inst ruction is the first valid write.

40.Chip enable or all byte enables are held inactive dur ing the two dummy writes to avoid data corruption.

41.OE is deasserted and tOHZ enabled to elapse before the first write operation is issued.

42.Any write scheduled to complete after OE is deasserted is pre-empted.

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 37 of 52

Figure 28. Read-to-Write-to-Read for Flow Through Mode (OE = LOW)

Switching Waveforms (continued)

tHDtSD

tSAC

tCKHZ1

tDC

tCD1

tSAC

tCYC

tHAC

tDC

tCD1tCD1

tCKLZ1

READ READWRITENOP

An A n + 1 A n + 2 An + 2 An + 3 An + 4

DQn + 2

DQn DQn + 1 DQn + 3

R/W

BEn

CE1

DQOUT

DQIN

tHAC

CE0

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 38 of 52

Figure 29. Read-to -Write-to-Read for Flow Through Mode (OE Controlled)

Switching Waveforms (continued)

tCD1

tCKLZ1

tHDtSD

tOHZ

tDCtCD1

tHAC

tSAC

tCYC

tDC

tCD1

tOE

READ READWRITE

A n A n + 1 A n + 2 An + 3 A n + 4 A n + 5

DQn + 2 DQ n + 3

DQn DQ n + 4

R/W

BEn

CE1

DQOUT

DQIN

tHAC

tSAC

CE0

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 39 of 52

Figure 30. BUSY Timing, WRITE-WRITE Collision for Pipelined and Fl ow Through Modes, C lock Timing Violates tCCS.

(Flag Both Ports)

Switching Waveforms (continued)

Port A

R/W

tBSY tBSY

BUSY

Port B < tCCS

R/W

tBSY tBSY

BUSY

Losing Port

R/W

tBSY tBSY

BUSY

Winning Port

R/W

tccs

Match

Figure 31. BUSY Timing, WRITE-WRITE Collision for Pipelined and Flow Through Modes, Clock Timing Meets tCCS.

(Flag Losing Port)

BUSY

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 40 of 52

Figure 32. Read with Echo Clock for Pipelined Mode (CQEN = HIGH)

Switching Waveforms (continued)

n+1

n+2

n+3

n+4

n+5

n+6

x-1

n+1

n+2

n+3

n+4

SAC

HAC

CQ1

CQ0

CQ0 t

CCQ

CQHQV

CQHQX

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 41 of 52

Figure 33. Mailbox Interrupt Output

Switching Waveforms (continued)

CYC

INT

MAX

SINT

RINT

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 42 of 52

Ordering Information

512K

72 (36 Mbit) 1.8V/1.5V Synchronous CYD36S72V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD36S72V18-200BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S72V18-200BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

167 CYD36S72V18-167BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S72V18-167BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S72V18-167BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S72V18-167BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

133 CYD36S72V18-133BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S72V18-133BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S72V18-133BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S72V18-133BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

256K

72 (18 Mbit) 1.8V/1.5V Synchronous CYD18S72V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD18S72V18-200BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S72V18-200BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD18S72V18-200BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S72V18-200BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

167 CYD18S72V18-167BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S72V18-167BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD18S72V18-167BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S72V18-167BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

128K

72 (9 Mbit) 1.8V/1.5V Synchrono us CYD09S72V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD09S72V18-200BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S72V18-200BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD09S72V18-200BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S72V18-200BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

167 CYD09S72V18-167BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S72V18-167BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD09S72V18-167BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S72V18-167BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 43 of 52

64K

72 (4 Mbit) 1.8V/1.5V Synchronous CYD04S72V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD04S72V18-200BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S72V18-200BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD04S72V18-200BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S72V18-200BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

167 CYD04S72V18-167BGXC 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S72V18-167BGC

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

CYD04S72V18-167BGXI 51-85218

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S72V18-167BGI

484-Ball Grid Array 23 mm x 23 mm with 1.0 mm pitch

1024K

36 (36 Mbit) 1.8V/1.5V Synchronous CYD36S36V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD36S36V18-200BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S36V18-200BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

167 CYD36S36V18-167BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S36V18-167BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S36V18-167BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S36V18-167BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

133 CYD36S36V18-133BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S36V18-133BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S36V18-133BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S36V18-133BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

512K

36 (18 Mbit) 1.8V/1.5V Synchronous CYD18S36V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD18S36V18-200BBAXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S36V18-200BBAC

256-ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD18S36V18-200BBAXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S36V18-200BBAI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD18S36V18-167BBAXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S36V18-167BBAC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD18S36V18-167BBAXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S36V18-167BBAI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

Ordering Information (continued)

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 44 of 52

256K

36 (9 Mbit) 1.8V/1.5V Synchrono us CYD09S36V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD09S36V18-200BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S36V18-200BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD09S36V18-200BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S36V18-200BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD09S36V18-167BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S36V18-167BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD09S36V18-167BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S36V18-167BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

128K

36 (4 Mbit) 1.8V/1.5V Synchrono us CYD04S36V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD04S36V18-200BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S36V18-200BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD04S36V18-200BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S36V18-200BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD04S36V18-167BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S36V18-167BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD04S36V18-167BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S36V18-167BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

64K

36 (2 Mbit) 1.8V/1.5V Synchronous CYD02S36V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD02S36V18-200BBXI 51-85108 256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free) Industrial

167 CYD02S36V18-167BBXI 51-85108 256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free) Industrial

Ordering Information (continued)

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 45 of 52

2048K

18 (36 Mbit) 1.8V/1.5V Synchronous CYD36S18V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD36S18V18-200BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S18V18-200BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

167 CYD36S18V18-167BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S18V18-167BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S18V18-167BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S18V18-167BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

133 CYD36S18V18-133BGXC 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD36S18V18-133BGC

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

CYD36S18V18-133BGXI 001-07825

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD36S18V18-133BGI

484-Ball Grid Array 27 mm x 27 mm with 1.0 mm pitch

1024K

18 (18 Mbit) 1.8V/1.5V Synchronous CYD18S18V18 Dual Port SRAM

Speed

MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD18S18V18-200BBAXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S18V18-200BBAC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD18S18V18-200BBAXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S18V18-200BBAI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD18S18V18-167BBAXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD18S18V18-167BBAC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD18S18V18-167BBAXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD18S18V18-167BBAI

256-Ball Grid Array 17 mm x 17mm with 1.0 mm pitch

512K

18 (9 Mbit) 1.8V/1.5V Synchrono us CYD09S18V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD09S18V18-200BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S18V18-200BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD09S18V18-200BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S18V18-200BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD09S18V18-167BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD09S18V18-167BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD09S18V18-167BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD09S18V18-167BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

Ordering Information (continued)

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 46 of 52

256K

18 (4 Mbit) 1.8V or 1.5V Synchronous CYD04S18 V18 Dual Port SRAM

Speed

(MHz) Ordering Code Package

Diagram Package Type Operating

Range

200 CYD04S18V18-200BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S18V18-200BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD04S18V18-200BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S18V18-200BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

167 CYD04S18V18-167BBXC 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Commercial

CYD04S18V18-167BBC

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

CYD04S18V18-167BBXI 51-85108

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch (Pb-Free)

Industrial

CYD04S18V18-167BBI

256-Ball Grid Array 17 mm x 17 mm with 1.0 mm pitch

Ordering Information (continued)

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 47 of 52

Package Diagrams

Figure 34. 256-Ball FBGA (17 x 17 mm), 51-85108

BOTTOM VIEW

TOP VIEW

1098765432 1

PIN 1 CORNER

0.20(4X)

Ø0.25MCAB

Ø0.05 M C

Ø0.45±0.05(256X)-CPLD DEVICES (37K & 39K)

0.25 C

0.70±0.05

SEATING PLANE

0.15 C

16 15 14 13 12 11

161513 141210 11928765431

Ø0.50 (256X)-ALL OTHER DEVICES

+0.10

-0.05

A1 0.36 0.56

A 1.40 MAX. 1.70 MAX.

REFERENCE JEDEC MO-192

15.00

1.00

0.35

17.00±0.10

7.50

15.00

17.00±0.10

1.00

-0.05

+0.10

51-85108-*F

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 48 of 52

Figure 35. 484-Ball PBGA (23 mm x 23 mm x 2.03 mm), 51-85218

Package Diagrams

Ø0.50~Ø0.70(484X)

0.97 REF.

0.20 C

0.56 REF.

SEATING PLANE

-C-

30° TYP.

0.40~0.60

0.132.03 ±

PIN #1 CORNER

1.00

20.00 REF.

3.20*45°(4x)

20.00 REF.

-A-

0.20(4X)

-B-

23.00±0.20

21.00

23.00±0.20

21.00

Ø1.00(3X) REF.

359

10 12

1614

13 15

17 21

20 22 22

21 17

18 16 1214

11 9

1.00

8642

Package Weight - 2.0 grams

Jedec Outline - Design Guide 4.14

0.25 C

0.35 C

51-85218-**

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 49 of 52

Figure 36. 484-Ball PBGA (27 mm x 27 mm x 2.33 mm), 001-07825

Package Diagrams

001-07825-**

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 50 of 52

Document History Page

Document Title: FullFlex™ Synchronous SDR Dual Port SRAM

Document Number: 38-06082

REV. ECN NO. Submission

Date Orig. of

Change Description of Chang e

** 302411 Se e ECN YDT New data sheet

*A 334036 See ECN YDT Corrected typ o on page 1

Reproduced PDF file to fix formatting errors

*B 395800 See ECN SPN Added statement about no echo clocks for flow through mode

Updated electrical characteristics

Added note 16 and 17 (1.5V timing)

Added note 33 (timing for x18 devices)

Updated input edge rate (note 34)

Updated table 5 on deterministic access control logic

Added description of busy readback in deterministic access control section

Changed dummy write descriptions

Updated ZQ pins connection details

Updated note 24, B0 to BE0

Added power supply requirements to MRST and VC_SEL

Added note 4 (VIM disable)

Updated supply voltage to ground potential to 4.1 V

Updated parameters on table 15

Updated and added parameters to table 16

Updated x72 pinout to SDR only pinout

Updated 484 PBGA pin diagram

Updated the pin definition of MRST

Updated the pin definition of VC_SEL

Updated READY descri ption to include Wired OR note

Updated master reset to include wired OR note for READY

Updated minimum VOH value for the 1.8V LVCMOS configuration

Updated electrical characteristics to include IOH and IOL values

Updated electrical characteristics to include READY

Added IIX3

Updated maximum input capacitance

Added Notes 33 and 34Removed Notes 15 and 17

Updated Pin Definitions for CQ0, CQ0, CQ1, and CQ1

Removed -100 Speed bin from Table.1 Selection Guide

Changed voltage name from VDDQ to VDDIO

Changed voltage name from VDD to VCORE

Moved the Mailbox Interrupt Timing Diagram to be the final timing diagram

Updated the Package Ty pe for the CYD36S18V18 parts

Updated the Package Ty pe for the CYD18S18V18 parts

Updated the Package Ty pe for the CYD18S36V18 parts

Included the Package Diagram for the 256-Ball FBGA (19 x 19 mm) BW256

Included an OE Controlled Write for Flow through Mode Switching Waveform

Included a Read with Echo Clock Switching Waveform

Updated Figure 5 and Figure 6

Updated Electrical Characteristics for READY VOH an d READY V

Updated Electrical Characteristics for VOH and VOL for the -167 and -133 speeds

Included a Unit column for Table 5

Removed Switching Characteristic tCA from chart

Included tOHZ in Switching W aveform OE Controlled Write for Pipelined Mode

Included tCKLZ2 in Waveform Read-to-Write-to-Read for Flow through Mode

[+] Feedback

FullFlex

Document Number: 38-0608 2 Rev. *H Page 51 of 52

*C 402238 SEE ECN KGH Updated AC Test Load and Wa veforms

Included FullFlex36 SDR 484-Ball BGA Pinout (Top View)

Included FullFlex18 SDR 484-Ball BGA Pinout (Top View)

Included Timing Parameter tCORDY

*D 45813 1 SEE ECN YDT Changed ordering informatio n with

-free part numbers

Removed VC_SEL

Added IO and core voltage adders

Removed references to bin drop for LVTTL/2.5V LVCMOS and 1.5V core modes

Updated Cin and Cout

Updated ICC, ISB1, ISB2 and ISB3 tables

Updated busy address read back timing diagram

Added HTSL input waveform

Removed HSTL (AC) from DC tables

Added 484-ball 27 mmx27 mmx2.33 mm PBGA package

*E 470031 SEE ECN YDT Changed VOL of 1.8V LVCMOS to 0.45V

Updated tRSF

VREF is DNU when HSTL is not used

Formatted pin description table

Changed VDDIO pins for 36M x 36 and 36M x 18 pinouts

Changed 36Mx72 JTAG IDCODE

*F 500001 SEE ECN YDT DLL Change, added Clock Input Cycle to Cycle Jitter

Modified DLL description

Changed Input Capacitance Table

Changed tCCS number

Added note 31

*G 627539 SEE ECN QSL change all NC to DNU

corrected switching waveform for (CQEN = High) from both Pipeline and Flow

through mode to only pipeline mode

Modified master reset description

Modified switching characteristics tables, extracted signals effected by the DLL

into one table and combine all other signals into one table

updated package name

Added footnote for tHD, tHAC and tSAC

changed note 26 description

Document History Page

Document Title: FullFlex™ Synchronous SDR Dual Port SRAM

Document Number: 38-06082

REV. ECN NO. Submission

Date Orig. of

Change Description of Chang e

[+] Feedback

Document Number: 38-06082 Rev. *H Revised May 15, 2008 Page 52 of 52

FullFlex is a trademark of Cypress Semiconductor Corporation. All product and co mpany names mentioned in this document are trademarks of their respective holders.

FullFlex

of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used

for medical, li fe support, life sa ving, critica l con t rol o r safe ty a ppl i ca ti ons, unless pursuant to an express wr it ten ag reement with C ypr ess. Fur th er mor e, Cyp r ess d oe s no t a uth or i ze i ts product s f or use

as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support

systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),

United States copyright law s and i ntern atio nal t reaty p rovi sions. Cypr ess her eby gr ant s to li censee a per sonal , non- exclu sive, n on-transferable license to copy, use, modify, create derivative works of,

and compile the Cypress Source Co de and derivative works for the sole p urpose of creating custo m software and or firmware in support of l icensee product to be used only in conjun ction with a Cypress

integrated ci rcuit as speci fied in the app licable agreem ent. Any reprod uction, modifi cation, transla tion, compila tion, or represent ation of th is Source Code exce pt as specified above is prohibited without

the express written perm i ssion of Cypr ess.

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED W ARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress re serves the right to make ch anges without further notice to the materials described herein. Cypress does not

assume any liabili ty ar ising ou t of the ap plicati on or u se o f any prod uct or c ircuit descri bed h erein. Cypress d oes not aut horize its pro duct s for use a s critical compo nent s in life-support systems whe re

a malfunctio n or failure may reasonab ly be expected to result in significant injury t o the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer

assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Use may be limited by and subject to the applicable Cypress software license agreement.

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office

closest to you, visit us at cypress.com/sales.

Products

PSoC psoc.cypress.com

Clocks & Buffers clocks.cypress.com

Wireless wireless.cypress.com

Memories memory.cypress.com

Image Sensors image.cypress.com

PSoC Solutions

General psoc.cypress.com/solutions

Low Power/Low Voltage psoc.cypress.com/low-power

Precision Analog psoc.cypress.com/precision-analog

LCD Drive psoc.cypress.com/lcd-drive

CAN 2.0b psoc.cypress.com/can

USB psoc.cypress.com/usb

*H 2505003 See ECN VKN/

AESA Modified footnote #1

Removed 250 MHz spe ed bin

Added 2-Mbit part and it’s related information

Changed ball name ZQ1 to DNU for 18M and lesser density devices

Added 256-Ball (17 x 17 mm) BGA package for 18M

Made PORTSTD[1:0] left and right pins driven only by LVTTL reference level

For 1.8V LVCMOS level, Changed VIH(min) from 1.26V to 0.65 times VDDIO and

Changed VIL(max) from 0.36V to 0.35 times VDDIO

Changed tHD, tHAC specs for 36M from 0.6 ns/0.7 ns to 0.8 ns (See footnote# 32)

Updated Ordering Information table

Document History Page

Document Title: FullFlex™ Synchronous SDR Dual Port SRAM

Document Number: 38-06082

REV. ECN NO. Submission

Date Orig. of

Change Description of Chang e

[+] Feedback